ZXP Series 7 User`s Manual (en)
Contents
1. Printer User s Manual P1036101 001 6 Cleaning Cleaning the Laminator Step 8 For dual sided laminators only Locate the bottom roller circled below for the lower cassette Step 9 Prepare a second Cleaning Swab Step 10 Locate the bottom roller circled below for the lower cassette Step 11 When ready press Bottom Step 12 Clean the bottom media roller by moving the swab tip side to side until the roller stops turning Only use moderate pressure Step 13 Press Exit to conclude the laminator rollers cleaning process Step 14 The OCP will return to the Clean Printer Menu Step 15 Install the laminate top and bottom spools and close the covers P1036101 001 Zebra ZXP Series 7 Card Printer User s Manual 125 6 Cleaning Cleaning the Laminator Clean the Laminator Oven Heater Rollers Step 1 From the Clean Printer Menu select CLEAN LAM OVEN and follow the OCP instructions Step 2 Wait until the oven temperature falls below 60 C Step 3 Open the laminator covers Step2. 4 Remove the four thumb screws circled below holding the Heater Assembly in place Step 5 Slide the Heater Assembly out of the Laminator arrow below Caution For the next step you may have to wait until the Heater Assembly can be handled comfortably Step 6 When ready press Next 126 Zebra ZXP Series 7 Card Printer User s Manual P1036101 001 P1036101 001 6 Cleaning Cleaning the Laminator Step 7 Prepare the Laminator Hot Roller Cleaning Card for use Step 8 Insert the cleaning card between the heater rollers arrow below Step 10 Remove the card from the Heater Assembly a Step 11 Turn the card over and repeat Step 8 Step 9 and Step 10 Step 12 Press Next to conclude the laminator oven cleaning process Step 13 The OCP will return to the Clean Printer Menu Zebra ZXP Series 7 Card Printer User s Manual 127 6 Cleaning Cleaning the Laminator Step 14 Reinstall the Heater Assembly a Remove the Thumb Drive Tool circled below b While carefully sliding the Heater Assembly into place use the Thumb Drive Tool to slowly rotate the gears counterclockwise dashed arrow until the gears mesh and the Heater Assembly seats properly c Install and tig
3. A Cleaning Caution PROTECT YOUR FACTORY WARRANTY The recommended cleaning procedures must be performed to maintain your factory warranty Allow only Zebra authorized technicians to service the Printer for all tasks other than the recommended cleaning procedures described in this manual NEVER loosen tighten adjust bend etc any part or cable inside the printer NEVER use a high pressure air compressor to remove particles in the printer 6 1 Introduction P1036101 001 NOTE To order a Printer Cleaning Kit go to http www zebra com supplies Clean the Printer using the Cleaning Cards provided in the Printer Cleaning Kit specified in the Note above The regular use of these cards will clean and maintain important parts of the printer including the Printhead Transport Rollers and optional Magnetic Encoder Station Printer usage total number of cards printed and total number of cards laminated can be found on the printer s Properties Device Information tab To access the Device Information tab select Start gt Devices and Printers Right click on the Zebra ZXP Series 7 Card Printer listing and select Printer properties gt Device Information Zebra ZXP Series 7 Card Printer User s Manual 117 6 Cleaning Cleaning the Printer Cleaning the Printer NOTE To order a Printer Cleaning Kit go to http www zebra com supplies When to Clean Cleaning requirements vary according to the environment F
4. aminator Media Rollers at this time see Clean the Laminator Media Rollers on page 124 otherwise go to Step 10 Open the laminator covers install the laminate top and bottom spools and close the covers Close the print cover Zebra ZXP Series 7 Card Printer User s Manual 123 6 Cleaning Cleaning the Laminator Clean the Laminator Media Rollers Step 1 From the Clean Printer Menu select CLEAN LAM ROLLERS to run the Laminator Media Roller Cleaning Routine and follow the OCP instructions Step 2 Wait until the oven temperature falls below 60 C Step 3 Open the laminator covers remove the laminate top and bottom cassettes and leave both covers open Step 4 Prepare a Cleaning Swab for use Step 5 Locate the top roller circled below for the upper cassette Step 6 When ready press Next and then press Top Step 7 Clean the top media roller by moving the swab tip side to side until roller stops turning Only use moderate pressure 124 Zebra ZXP Series 7 Card
5. e Clean Printer Menu P1036101 001 Zebra ZXP Series 7 Card Printer User s Manual 119 120 6 Cleaning Cleaning the Printer Clean the Feeder Path NOTE Do not use previously used cleaning cards Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 From the Clean Printer Menu select CLEAN FEEDER Use the Feeder Cleaning Card and follow the OCP instructions Remove all cards from feeder cartridge and then press Next Insert short cleaning card in top slot then press Clean Press yellow button in feeder cartridge to release pusher plate and then press Next Wait while cleaning process completes The card will eject through same slot Flip the cleaning card reinsert it in top slot and then press Clean Wait while cleaning process completes The card will eject through same slot The OCP will return to the Clean Printer Menu Load the cards back into the feeder cartridge Zebra ZXP Series 7 Card Printer User s Manual P1036101 001 6 Cleaning Cleaning the Printer Polish the Printhead NOTE Use is password protected and limited to Zebra authorized service personnel The Advanced Cleaning button in the Clean Printer section of the ZXP Toolbox provides access to printhead polishing When printhead polishing is enabled in the ZXP Toolbox printhead polishing can be done via the OCP Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Enab
6. hten the four thumb screws removed in Step 4 Step 15 Close the laminator covers 128 Zebra ZXP Series 7 Card Printer User s Manual P1036101 001 6 Cleaning Dual Cleaning Cartridge Dual Cleaning Cartridge The Dual Cleaning Cartridge cleans the cards entering the printer via the card feeder To ensure print quality the card cleaning rollers inside the cartridge require periodic replacement Two new card cleaning rollers are included with each ribbon or may be purchased separately To order additional rollers go to http www zebra com supplies Installation of the Dual Cleaning Cartridge is described in Section 2 and is not repeated in detail here Manual Feed Cleaning Cassette The Cleaning Cassette cleans the cards entering the printer via the Manual Feed Slot To ensure print quality the card cleaning roller inside the cassette requires periodic replacement Two new card cleaning rollers are included with each print ribbon or may be purchased separately To order additional rollers go to http www zebra com supplies Installation of the Cleaning Cassette is described in detail in Section 2 and is not repeated here Phone 800 860 9111 IDentiph OO 1810 Joseph Lloyd Pkwy Fax 440 306 9001 Willoughby OH 44094 e mail sales IDentiphoto com Specialists in IDentification web www Dentiphoto com P1036101 001 Zebra ZXP Series 7 Card Printer User s Manual 129
7. le printhead polishing in the ZXP Toolbox Press the MENU button on the Operator Control Panel OCP The OCP will display the Main Menu Scroll through the Main Menu and select Advanced Settings The OCP will display the Advanced Settings Menu Scroll through the Advanced Settings Menu and select Clean Printer From the Clean Printer Menu select POLISH PRINTHEAD Open the printer cover and ribbon drawer remove the ribbon and press Next Close the ribbon drawer and printer cover and press Next Insert a Polishing Card grit up in the Manual Feed Slot and press Clean Step 8 Wait until the cleaning process completes The card will be ejected through the same slot Step 9 Replace the ribbon and press Next to return to the Advanced Settings Menu yj NOTE Card Path Cleaning Page 119 is recommended after printhead polishing to P1036101 001 remove any loose debris from the printer Zebra ZXP Series 7 Card Printer User s Manual 121 6 Cleaning Cleaning the Laminator Cleaning the Laminator NOTE To order a Laminator Cleaning Kit go to http www zebra com supplies When to Clean Cleaning requirements vary according to the environment For a typical office environment the recommended cleaning cycle is e Laminator Card Path cleaning should occur every 5 000 cards e Laminator Roller cleaning should occur every 5 000 cards e Laminator Oven Heater Rollers cleaning should occur eve
8. or a typical office environment the recommended cleaning cycle is e Card Path cleaning should occur every 5 000 cards e Feeder Path cleaning should occur every 5 000 cards Initiate the Cleaning Process Step 1 Press the MENU button on the Operator Control Panel OCP The OCP will display the Main Menu Step 2 Scroll through the Main Menu and select Advanced Settings The OCP will display the Advanced Settings Menu Step 3 Scroll through the Advanced Settings Menu and select Clean Printer The OCP will display the Clean Printer Menu 118 Zebra ZXP Series 7 Card Printer User s Manual P1036101 001 6 Cleaning Cleaning the Printer Clean the Card Path NOTE Do not use previously used cleaning cards Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 From the Clean Printer Menu select CLEAN CARD PATH Use the Printer Cleaning Card and follow the OCP instructions Open print cover open ribbon drawer remove ribbon and then press Next Close ribbon drawer close print cover and then press Next Insert long cleaning card in Manual Feed Slot and then press Clean Wait while cleaning process completes The card will eject through same slot Flip the cleaning card reinsert it in the Manual Feed Slot and then press Clean Wait while cleaning process completes The card will eject through same slot Replace the ribbon and press Next Step 10 The OCP will return to th
9. ry 20 000 cards Initiate the cleaning process NOTE To avoid a long wait while the heated rollers cool to 60 C perform cleaning before y i the rollers heat 1 e when first turned on and the rollers are still cold Step 1 Press the MENU button on the Operator Control Panel OCP The OCP will display the Main Menu Step 2 Scroll through the Main Menu and select Advanced Settings The OCP will display the Advanced Settings Menu Step 3 Scroll through the Advanced Settings Menu and select Clean Printer The OCP will display the Clean Printer Menu 122 Zebra ZXP Series 7 Card Printer User s Manual P1036101 001 6 Cleaning Cleaning the Laminator Clean the Laminator Card Path Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 P1036101 001 From the Clean Printer Menu select CLEAN LAM CARD PATH to run the Laminator Cleaning Routine and follow the OCP instructions Wait until the oven temperature falls below 60 C If you have laminate installed open the laminator covers remove the laminate top and bottom cassettes and close the covers Open the print cover to raise the printhead then press Next Insert the Laminator Cleaning Card into the Manual Feed Slot then press Clean Wait while the cleaning process completes The card will be ejected into the output hopper The OCP will return to the Clean Printer Menu If you want to clean the L
Download Pdf Manuals
Related Search