Home

2060 KB - R-One Trading

1. SNTP Server SNIP Server Bridge Figure 2 10 Changing Bridge Mode to Router or NAT Mode SB3415 03 Only airClient TOTAL 3415 User Guide Page 24 of 61 intelligent wireless platform 2 9 airClient TOTAL Bridge Configuration sB3415 03 only This section is only valid for the sB3415 03 model The airClient TOTAL in Bridge mode can associate only with a smartBridges airPoint access point in bridge mode as they both use WDS link implementation 2 9 1 LAN Settings This section outlines the procedures for changing the IP settings for bridge mode 1 From the navigation menu bar click on Home LAN Settings to change Ethernet wired side parameters The LAN Settings screen will appear as shown below in Fig 2 11 2 Enter the System Name of the unit if needed 3 Enter the IP address and Subnet mask to set the LAN IP address and subnet mask and any Gateway Address if required Assign the unit a unique IP Address in the designated IP subnet 4 Click on Save to save the changes The settings will be applied after the reboot Home LAN Setting airClient TOTAL 5B3415 03 Bridge mode LAN Setting IP Mode static IP Dynamic IP DHCP Client System Name 8B3415 03 IP Address 192168025 Subnet Mask 255 255 255 0 Gateway Address 192 168 2 220 Save Reset Figure 2 11 airClient TOTAL Bridge LAN Settings sB3415 03 Only 2 9 2 Radio Se
2. Note The system will validate the input parameters and notify users of invalid entry The DHCP Server IP will be in the same network segment as the device wireless Radio IP address The DHCP Server needs to be configured to serve IP range of the wired side Ethernet IP The DHCP Relay Agent is only available to hosts connected to the same LAN segment as the device wired side Ethernet port Networking DHCP Server airClient TOTAL sB3415 03 Router mode DHCP Server Setting DHCP Server provides automation and control of IP address assignment services Enable DHCP Server Enable DHCP Relay Disable DHCP and DHCP Relay once Server IP 192 168 2 220 Save Reset Figure 2 22 airClient TOTAL DHCP Relay Configuration airClient TOTAL 3415 User Guide Page 36 of 61 intelligent wireless platform 2 10 5 IP Port Forwarding IP Port forwarding also referred to as Virtual Server in this document allows the user to define the port mapping between the local area network and the public network This feature is only available when the device is configured in the NAT mode Follow the steps below to map a local port to the global port accessible through the wireless interface 1 Click on Networking IP Port Forwarding from the menu bar to access the IP Port Forwarding page 2 Depending on the application select the protocol as TCP UDP 3 Enter the Local IP Address and the Loc
3. 5 Click on Save to save the settings The settings will take effect after the Reboot Networking Bandwidth Control airClient TOTAL sB3415 02 Router mode Bandwidth Control D Broadcast Packet Piter f I 50 O multicast Packet Filter F s 9 M Bandwidth Control Kbps 1024 Figure 3 2 airClient TOTAL Bandwidth Control SB3415 01 sB3415 02 Save Reset Networking Bandwidth Control airClient TOTAL sB3415 03 Router mode Bandwidth Control O Broadcast Packet Filter F s 50 O Multicast Packet Filter F s Lal Set Download Bandwidth Kbps M Set Upload Bandwidth Kbps 3000 Save Reset Figure 3 3 airClient TOTAL Bandwidth Control SB3415 03 airClient TOTAL 3415 User Guide Page 46 of 61 4 Traffic Statistics intelligent wireless platform Wireless Statistics can be displayed by clicking on Networking Wireless Statistics from the navigation menu The following figure shows the s Networking Wireless Statistics tatistics page Recieve Total Bytes 27154 Broadcast Packets 0 Multicast Packets 0 Unicast Packets 0 airClient TOTAL sB3415 03 Router mode Transmit 24328 69 20 137 Up Time Day 0 0 02 19 Figure 4 1 airClient TOTAL Wireless Statistics The following table summarizes the information for the wireless traffic settings Table 4 1 Wireless Traffic Statistics Wireless Traffic Statistics T
4. SSID of a Radio Up to 32 characters IP address of Ethernet Port 32 bit numeric address IP address of Wireless Port 32 bit numeric address RSSI dBm At present Level in the current firmware version Channel selected for link Radio TX Output Power 0 to 18 dBm Model of smartBridges airClient TOTAL equipment selected for a link sB3415 Antenna Type Internal External Antenna Manufacturer smartBridges Name of other manufacturer Antenna Polarization Horizontal Vertical Beam width of antenna Horizontal deg Vertical deg Antenna Gain airClient TOTAL 3415 User Guide dBi Page 9of 61 Check the crimping of the Ethernet cable at both the ends intelligent Yes No wireless platform Check the proper grounding of the antenna and equipment Yes No Ensure that there are no extreme bends or kinks in the cable Yes No Ensure Ethernet cable is not running near a sharp edge Yes No 5 Ensure antenna is aligned to get the best RSSI Yes No and link quality 6 Ping response ms 7 Ping success rate Percentage 8 Throughput test Upload Download Mbps 9 Link stability based on observation for 1 hour Yes No 10 Shielded RJ 45 cable to be used from POE to Yes No the unit Signature of Engineer Installation Date Commissioned Date For th
5. 1 Click on Networking IP Port Forwarding from the menu bar to Access the Port Forwarding Table page 2 In case you want to edit an existing entry click on the Edit corresponding to the row The entries will show up in the fields Edit the entries and click the Update button to update the table 3 In case you want to delete an existing entry from the Port Forwarding table select the mapping you wish to delete and click Delete 4 Click on Tools Reboot to reboot the unit for the changes to be effective Networking IP Port Forwarding airClient TOTAL sB3415 03 NAT mode Virtual Server defines the port mapping between Local 4rea Network and public network Virtual Server Protocol TCP ze Local IP Address 1192 158 0 10 Local Port 21 Global Port 21 Status Activate Y Add sr ID Local IP and Port Global Port Protocol Status BH Figure 2 25 Editing IP Port Forwarding Table Entry 2 10 6 Routing Table The airClient TOTAL Router web interface has the provision to add delete or view static routes To view the routing table page click on Networking Routing Table from the menu bar To enable dynamic routing select Support RIP v2 on the Routing Table page Dynamic Routing is enabled by default Page 38 of 61 intelligent wireless platform Adding and deleting static routes is allowed in the Router Mode of the airClient TOTAL Follow the steps b
6. 192 168 2 225 Network Mask 255 255 255 0 Gateway Address 1192 168 2 254 d MTU DNs Passthrough Manually Set DNS DNS Server Secondary DNS Save Reset Figure 2 15 airClient TOTAL Router NAT WLAN Settings Static WLAN connection airClient TOTAL 3415 User Guide Page 29 of 61 intelligent wireless platform Home WLAN Setting airClient TOTAL sB3415 03 Router mode WLAN Setting Connection Type O Dynamic O Static IP Address 192 158 2 50 Network Mask 255 255 255 0 Gateway Address 192 168 2 220 MTU Cpns Passthrough Manually Set DNS DNS Server 192 168 0225 Secondary DNS Save Reset Figure 2 16 airClient TOTAL Router NAT WLAN Settings Dynamic WLAN Connection For the airClient TOTAL device to associate with an access point the user also needs to configure the access point s SSID security if used and select External Internal antenna options airClient TOTAL 3415 User Guide Page 30 of 61 TT Request Release gt intelligent wireless platform Follow the steps below to configure the airClient TOTAL Router NAT Mode wireless association parameters i Note airClient TOTAL 3415 User Guide From the navigation menu bar click on Radio Wireless Settings to set the SSID and wireless mode 802 11 b g The Wireless Settings screen will be disp
7. 3 A user login box as shown below Fig 2 1 will appear Enter the User name and Password The default user name is administrator and the password is smartBridges case sensitive Connect to 192 168 0 225 smartBridges User name administrator Password eocccccccese C Remember my password Figure 2 1 airClient TOTAL Administrator Login 4 Click on the OK button A license agreement page will appear as shown in Fig 2 2 below 5 Click Accept The airClient TOTAL Summary Information page Fig 2 3 will appear airClient TOTAL 3415 User Guide Page 11 of 61 intelligent wireless platform Terms of use Software License amp Software Packages airClient TOTAL 241 sB3415 01 sB3415 02 3B3415 03 Software Copyright and Distribution Licenses airClient TOTAL 241 is Copyright 2004 2007 by smartBridges All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution Software Warranty smartBridges warrants that commencing from the date of purchase from a smartBridges authorized distributor reseller to Customer and continuing for a period of 12 months or 16 months from the date of manufacture whichev
8. Key Entry Method HEX v Key Entry Instruction e 64 10 HEX or 5 Ascii e 128 26 HEX 13 Ascii Key ID Key Key Length Key 10 abcde12345 oi sg Key2 None Key 3 None sl f GH eem Gees Key4 i None sl Save Reset Figure 2 29 airClient TOTAL Security Open System Shared Key Configuration Table 2 4 Security Settings for Open System Shared Key Page Items Descriptions Choose between open system and shared key authentication modes Authentication Type Open System Open System is null authentication With WEP enabled airClient TOTAL 3415 User Guide Page 41 of 61 intelligent wireless platform Page Items Descriptions and valid WEP key on both ends it provides data encryption Shared Key Strict authentication for both authentication and data encryption Clients must provide valid WEP key to associate Choose HEX if the key entered is the Hexadecimal format choose ASCII Key Entry Method if the key entered is in ASCII format Key ID Select one of the key indexes from the 1 to 4 Key The value of the encryption key Choose encryption key size between 64bits and 128bits Key Length 64 bits User has to input 10 HEX digits 128 bits User has to input 26 HEX digits 2 11 2 WPA PSK In order to configure WPA PSK follow the steps as shown below 1 Click on Radio Security from the main menu screen as shown in the figure
9. deena Verify Password Save Reset Figure 5 4 airClient TOTAL Read Only User Configuration 5 6 SNMP Configuration The user can enable or disable the SNMP configuration using this tool Follow the steps below to change the SNMP settings 1 l Click on Tools SNMP Configuration to access the SNMP Configuration page as shown below in Fig 5 5 airClient TOTAL 3415 User Guide Page 51 of 61 intelligent wireless platform 2 Enable or Disable SNMP by using the checkbox 3 Set the Read Community String to smartBridges 4 Set the System Contact Location on the page if required 5 Click on the Save button for the changes to take effect Tools SNMP Configuration airClient TOTAL sB3415 02 Router mode SNMP Configuration Enable SNMP kd Read Community String smarBridges TF Write Community String System Contact Smartbridges System Location Singapore Save Reset Figure 5 5 airClient TOTAL SNMP Configuration airClient TOTAL 3415 User Guide Page 52 of 61 intelligent wireless platform 5 7 Backup Restore Settings The Backup Restore page backs up good configuration settings of the system This can be used to restore the unit in case of any undesired circumstances Follow the steps below to change the Backup Restore settings 1 From the navigation menu bar click on Tools Backup Restore to save or restore the settings on the
10. Reset To Factory Defaults Reset to Defaults Ethernet MTU Size 1500bytes O Bridge O Router Figure 5 1 airClient TOTAL System Configuration airClient TOTAL 3415 User Guide Page 48 of 61 intelligent wireless platform The following table summarizes the information for the System Configuration page Table 5 1 System Configuration Page Items Configuration Page Item Descriptions System Name Name of the airClient TOTAL SNMP This field links to the SNMP Configuration page settings This button Resets the airClient TOTAL unit A message box is prompted to the Reset user to confirm the reboot SNTP Server Allows user to set the Network Time Server and Time Zone Firmware Version The version of the firmware installed on the unit currently Local MAC SES Address The MAC Address of the local airClient TOTAL unit Reset to Factory Defaults This button resets the unit to the factory default settings A message box is prompted to the user to confirm resetting the unit to factory defaults Ethernet MTU Size Displays the Ethernet MTU size System Log Current Operational Mode This links to the System Log page settings Displays the operating mode of the unit This could be Router or NAT for sB3415 01 and sB3415 02 models This could be Bridge or Router or NAT for sB3415 03 model 5 2 SNTP Setting The device time comes from the network time information source The
11. you need to have fundamental understanding of the concepts and technology of Local Area Networks LAN and wireless networking The system installer will require expertise in the following areas e Outdoor radio equipment installation e Network configuration e Use of web browser for system configuration monitoring and fault finding In this chapter you will find an overview of the user guide and where to obtain additional information regarding installation and set up Overview of User Guide This document provides comprehensive information about the application needed to set up configure and deploy the airClient TOTAL sB3415 unit It is organized into several chapters Chapter 1 e configuration features e system requirements Chapter 2 e deploying the airClient TOTAL 241 in Router or NAT or Bridge SB3415 03 only modes e modify of various configuration settings Chapter 3 e process of configuration on the radio performance parameters e bandwidth Controller Chapter 4 e display of the wireless traffic statistics Chapter 5 e the site survey tool e the system configuration tools airClient TOTAL 3415 User Guide Page 4of 61 intelligent wireless platform e backup restore features e firmware upgrade steps e using the License Key feature for bandwidth upgrade on the unit The abbreviations and acronyms used in this user guide are explained in the Appendix Related Publications In addition to this user
12. Lease Time The maximum time of the DHCP Leases The maximum allowable limit is 2880 minutes NAT Virtual Server Displays the no of entries in the IP Port Forwarding Table Routing Static Routing Displays the no of static routes in the Static Routing Table Setting airClient TOTAL 3415 User Guide Page 14of 61 intelligent wireless platform 2 2 Web GUI Administrator User Name and Password Change The default administrator user name for the airClient TOTAL 3415 is administrator and administrator password is smartBridges please note that this is case sensitive Follow the steps below to change the administrator user name and or password 1 From the top navigation menu bar click on Tools System Admin A System Administration interface will appear as shown below 2 Enter the user name you wish in the User Name field 3 Enter the new password in Password and Verify Password fields Click on the Save button to save the settings 4 Click on the Save button and a message box will appear to confirm if you wish to reboot the unit Click OK to reboot the unit and the new user name and password to take effect Tools System Administration airClient TOTAL sB3415 03 NAT mode System Administration User Name administrator Password 900000000000 Verify Password eocccccccccs Save Reset Figure 2 4 airClient TOTAL Administrator User Name Password Change airClient TOTA
13. Summary Information page will show the status as Associated if the unit has associated successfully as shown in Fig 2 13a below Under Networking Association Status the status will also show the Access Point that the client is associated with as shown in Fig 2 13b below Radio Advanced Settings airClient TOTAL sB3415 03 Bridge mode Advanced Setting SSID NEXUS MASTER SSID suppressed O Yes No Channel 2417MHz Channel 2 emote AP MAC Address 00 30 1 a 29 0040 2 4GHz 54Mbps 802 119 Wireless Mode Antenna Selection O Internal External Distance Within 1Km Country UNITED STATES US v 1 Data Rate Mbps Best v Default Data Rate Mbps 1 i Transmit Power 18 dBm ze Preamble Long Preamble vi Slot Time Short Slot Time ze Protection Mode None Protection Type CTS only RTS CTS RTS CTS Threshold Seefe Save Reset Figure 2 12 airClient TOTAL Bridge Radio Settings SB3415 03 Only airClient TOTAL 3415 User Guide Page 26 of 61 intelligent wireless platform Wireless Settings SSID NEXUS MASTER e Channel Current Channel 2 2417MHz Association Status Associated Wireless Mode 802 11g Security Mode Disable Figure 2 13a airClient TOTAL Summary Inf
14. The radio preamble is a section of data at the head of a packet that contains information the airClient device needs when Preamble sending and receiving packets By default this value is set to Long Slot Time This can be set to Long Short Time or Short Slot time Protection Mode Select None Always or Auto Protection Type Select CTS only or RTS CTS RTS CTS Default value is 2346 bytes The range of value is from 256 to Threshold 2346 bytes 3 2 Bandwidth Control Using the Bandwidth Controller the user can limit the wireless link bandwidth speed The maximum allowable bandwidth is up to 512Kbps in sB3415 01 1 Mbps in 3415 02 and 3 Mbps in 3415 03 This is subject to the available upstream bandwidth signal level and distance Note For the 3415 03 model only the user can control the upload and the download bandwidth for the wireless link Follow the steps below to change the bandwidth parameters 1 From the navigation menu bar click on Networking Bandwidth Control airClient TOTAL 3415 User Guide Page 45 of 61 intelligent wireless platform 2 Click on the Bandwidth Control button to enable the bandwidth controlling feature 3 Enter the desired value in kbps The maximum bandwidth allowable is 512 kbps for 3415 01 1024 kbps for 3415 02 and 3072 kbps for 3415 03 models 4 For the 3415 03 model the user can configure the upload and download limit separately as shown below in Fig 3 3
15. corner of each page The device mode configuration allows the user to configure the airClient TOTAL to a NAT Network Address Translation mode or Router mode for 3415 01 and 3415 02 models and NAT or Router or Bridge mode for the 3415 03 model These modes are explained below NAT This is the default operating mode This mode allows you to use one segment of private IP addresses for multiple hosts to access the external network using a single wireless IP address This translation helps in protecting the access of internal hosts from external network This mode is available in all SB3415 models Router This mode allows you to configure different segment of IP address in Ethernet and Wireless interface A standard routing functionality is available in this mode This mode is available in all sB3415 models Bridge A transparent bridging functionality is provided in this mode which uses WDS implementation This functionality is only available in sB3415 03 model pg aystamcortigurations 3B3415 03 SNMP Configuration System Name SNMP Configuration Reset Reset SNTP Server SNTP Server Firmware Version 2 0 0B1P0 5B3415 03 00 06 c7 01 03 08 Syslog Local MAC Address Reset To Factory Defaults Ethernet MTU Size System Log O Bridge O Router Figure 2 6 airClient TOTAL Device Mode Configuration airClient TOTAL 3415 User Guide Page 20 of 61
16. device needs access to a network timer NTP time server source The NTP time server IP can be configured as follows 1 From the navigation menu bar click on Tools SNTP Setting to configure the NTP Server A page as shown below will appear 2 Enter a valid SNTP server IP address and select the Time Zone The default NTP server is 128 250 36 2 and the default Time Zone is Singapore 3 Click on the Save button to configure the NTP 4 After the Save Reboot the network time will appear on the browser if the NTP server is contactable Tools SNTP airClient TOTAL sB3415 03 NAT mode The system gets the current time from SNTP server SNTP Server Address 128 250 36 2 Time Zone GMT 8 Beijing Hong Kong Singapore Taipei e airClient TOTAL 3415 User Guide Save Reset Reset Figure 5 2 airClient TOTAL SNTP Time Settings Page 49 of 61 intelligent wireless platform 5 3 Site Survey From the navigation menu bar click on Tools Site Survey to access the Site Survey page screen similar to the one below would show all the standards based wireless devices operating in the area Tools Site Survey airClient TOTAL sB3415 03 NAT mode ID Sel ESSID emp ME eent eg EE A 1 SpeedTouchDBFFC4 00 14 7F B0 86 03 802 11g 71 dBm NONE Infrastructure 2 0 RoofTop 00 30 14 01 00 0C 802 11b 1 8
17. set the Primary Secondary DNS Server airClient TOTAL 3415 User Guide Page 16 of 61 intelligent wireless platform Menu Item Menu Sub items Description Networking Wireless Statistics Displays traffic statistics on the Wireless side Association Status Shows the status of the association and the MAC of the AP associated with Shows the Link Status Graph for the associated link DHCP Allows user to Enable or Disable DHCP Server Allows user to Enable Disable DHCP Relay Note DHCP Relay feature is only applicable for the 3415 03 model DHCP List Displays the DHCP List if DHCP Server is Enabled IP Port Forwarding Allows user to add entries to map Local Area Network IP Address or port behind the NAT to a global port accessible through the wireless interface User will be able to use this option only when the unit is configured in the NAT mode Routing Table Allows the user to view add and delete or update static routes Allows the user to Enable or Disable RIP running on the device RIPv2 is run by default on the device Bandwidth Control Allows bandwidth management of the wireless link Radio Wireless Settings Allows the user to set SSID Enable or Disable SSID Suppressed select Internal or External antenna configure Distance select Data Rate set Transmit Power set Country settings Preamble and Slot time Secur
18. to an upper layer protocol WEP keys can be either statically configured or dynamically generated In either case WEP has been found to be easily broken WPA Wi Fi Protected Access WPA is a replacement security standard for WEP It is a subset of the IEEE 802 11i standard being developed WPA makes use of TKIP to deliver security superior to WEP 802 1X access control is still employed The Authentication Server provides the material for creating the keys airClient TOTAL 3415 User Guide Page 60 of 61 intelligent wireless platform COFDM COFDM involves modulating the data onto a large number of carriers using the OFDM technique The Key features which makes it work in a manner is so well suited to terrestrial channels includes e Orthogonality the O of COFDM e The addition of Guard interval e The use of error coding the C of COFDM interleaving and channel state information COFDM is resistant to multipath effects because it uses multiple carriers to transmit the same signal RIP The most popular of the TCP IP interior routing protocols is the Routing Information Protocol RIP RIP is used to dynamically exchange routing information RIP routers broadcast their routing tables every 30 seconds by default Other RIP equipments will listen for these RIP broadcasts and update their own route tables DHCP DHCP stands for Dynamic Host Configuration Protocol and is a means for networked computers
19. wireless platform Follow the steps below to edit or delete a static route entry in the airClient TOTAL operating in the Router Mode 1 Click on Networking Routing Table from the menu bar to access the view routing table page 2 From the Routing table on this page select the route you wish to delete and click Delete as shown in Fig 2 18 3 In case you want to edit the existing entry click on the Edit corresponding to the row The entries will show up in the fields Edit the entries and click the Update button to update the table 4 Click on Tools Reboot to reboot the unit for the changes to be effective Networking Routing Table airClient TOTAL sB3415 03 Router mode Routing Mode Selection Save You can manually set a routing entry here Enter the destination IP address and its network mask and the IP of which port the packets are forwarded to Dest IP 1192 168 3 0 IP Mask 255 255 255 0 Gateway 192 168 2 220 Status Activate Add Update ID Destination IP _IPMask Gateway Status 1 192 168 4 0 255 255 255 0 192 168 2 220 Activated Edit Figure 2 28 Deleting the Static Route 2 11 Security This section allows you to configure wireless encryption to prevent unauthorized parties from accessing the network The security options on the airClient TOTAL are as follows 1 Open System 2 Shared Key 3 WPA PSK Note By default security i
20. 2 18c below Page 31 of 61 intelligent wireless platform Radio Advanced Settings airClient TOTAL sB3415 03 Router mode Advanced Setting SSID NEXUS MASTER SSID suppressed OYes No Channel Remote AP MAC Address Wireless Mode Country UNITED STATES US Data Rate Mbps Default Data Rate Mbps 1 v Best ze Transmit Power 18 dBm Preamble Long Preamble v Slot Time Short Slot Time ze Protection Type CTS only RTS CTS RTS CTS Threshold 2346 en Figure 2 17 airClient TOTAL Router Wireless Settings Wireless Settings Current Channel 2 2417MH2 Association Status Wireless Mode 802 11g Figure 2 18a airClient TOTAL Summary Information page airClient TOTAL 3415 User Guide Page 32 of 61 intelligent wireless platform Networking Association Status airClient TOTAL sB3415 03 Router mode ID MAC Address Status Signal Strength NoiseFloor RSSI van EEN Show o 00 30 14 29 00 F0 up 43 dBm 96 dBm BAR Refresh Figure 2 18b airClient TOTAL Wireless Association Status E http 192 168 0 225 Station Graph Microsoft Internet Explorer DER Link Status for 00 30 14 29 00 F0 E 5 S ken a E L I Time s E RSSI Current 60 dBm Average 46 dBm Maximum 42 dBm E Noise Floor Current 96 dBm Average 96 dBm M
21. 2 dem WEP Infrastructure 3 O BRIDGE 00 30 14 29 00 F0 802 11g 6 50 dBm NONE Infrastructure 4 O Alliance 00 E0 98 2A 25 63 802 119 6 69 dBm WEP Infrastructure 5 DEMOROOM_AP 00 30 14 1F 51 7C 802 11b 6 74 dBm NONE Infrastructure 6 linksys 00 14 BF 04 C5 93 802 119 6 30 dBm NONE Infrastructure vd Ath Hello 00 02 6F BE F1 60 802 11g UV 82 dBm NONE Infrastructure 8 O Atheros_STN8 00 90 4B C1 A1 D6 802 11g 3 76 dBm NONE Infrastructure 9 DISNEY 00 30 14 1F 4C BE 802 119 3 83 dem NONE Infrastructure Save Refresh Figure 5 3 airClient TOTAL Site Survey The following table summarizes the information for the Site Survey items Table 5 2 Site Survey Page Items Page Item Descriptions Sel Allows the airClient TOTAL to associate with a different Access Point ESSID The network name for the wireless network BSSID The MAG address of the device Wireless Mode Displays the radio operating mode of the device Channel Displays the channel at which the device is operating RSSI Displays the signal strength of the corresponding device Displays the security mode that the device is currently operating in If WEP or Security security option is enabled on the Access Point then WEP needs to be enabled on the airClient TOTAL and WEP key defined prior to association Displays the current wireless mode of the device This could be Infrastructure or Network Mode Ad Hoc Save b
22. C Address IP Address 1 00 30 1a 01 7f fe 192 168 0 60 Figure 2 20 airClient TOTAL DHCP List Follow the steps below to disable the airClient TOTAL Router NAT DHCP server 1 From the Navigation menu bar click on Networking DHCP Server to access the DHCP configuration page 2 Select the DHCP and DHCP Relay button to disable the DHCP server configuration 3 Click on Save to save the settings The settings will be applied after the Reboot airClient TOTAL 3415 User Guide Page 35 of 61 intelligent wireless platform Networking DHCP Server airClient TOTAL sB3415 03 Router mode DHCP Server Setting DHCP Server provides automation and control of IP address assignment services Enable DHCP Server Enable DHCP Relay Disable DHCP and DHCP Relay Reset Figure 2 21 Disable DHCP and DHCP Relay 2 10 4 DHCP Relay Configuration If the user has a DHCP Server the airClient TOTAL Router can be configured as a DHCP Relay agent of the DHCP Server for IP address assignment Follow the steps below to configure the airClient TOTAL unit as a DHCP Relay Agent 1 From the Navigation menu bar click on Networking DHCP Server to access the DHCP configuration page 2 Click on Enable DHCP Relay to choose DHCP Relay mode 3 Enter a valid DHCP Server IP 4 Click on Save button to apply the settings and to start the DHCP relay agent
23. Firmware Upgrade Allows the user to upgrade downgrade the firmware on the unit Product License Key Allows the user to upgrade the unit to higher bandwidth or to convert the model from 3415 01 to 3415 02 3415 03 or vice versa Link Budget Planning Allows user to calculate the Link Budget between an airClient TOTAL unit and an Access Point Allows user to display the system log locally or remotely Currently this SES device will only log in case of any problems with the unit Reboot Allows user to reboot the unit Note All changes made to the unit will take effect only after a Reboot is done airClient TOTAL 3415 User Guide Page 18 of 61 intelligent wireless platform Menu Item Menu Sub items Description Technical Support Information on Technical Support User Guide Online Link to online user guide Allows user to register product and Help Product Registration and Feedback provide feedback or suggestions Checks smartBridges website for any Check for Updates software updates Geng General system description software About airClient TOTAL version information and warranty information Allows user to logout from the airClient Logout Logout TOTAL device airClient TOTAL 3415 User Guide Page 19 of 61 intelligent wireless platform 2 4 Device Mode Configuration The device operational mode is displayed at the top right hand
24. GPS co ordinates simplify the task of link planning GPS co ordinates may be entered in DD MM MM format airClient TOTAL sB3415 03 Router mode GPS Calculator Latitude1 02 06 07 N Longitude1 v 02 06 01 Latitude2 W 02 06 07 Longitude2 N m 02 06 33 Woy Compute Distance Course 1 2 Degrees 270 Course 2 1 Degrees Distance 90 1 miles Distance from Root Device to Remote Device is 1 miles vw Please Select Figure 5 11 airClient TOTAL Link Budget Planning GPS Calculator Once the distance is computed follow the steps below for the link budget calculations Alternatively the distance parameter can be manually entered in miles or kilometers without filling in the latitude longitude coordinates 1 Select the Radio Mode for station 1 and 2 2 Enter the Transmit Output Power in dBm for station 1 and 2 3 Enter the Antenna Gain in dB for station 1 and 2 4 Enter the RF Cable Losses in dB for station 1 and 2 airClient TOTAL 3415 User Guide Page 57 of 61 intelligent wireless platform 5 Click the Compute Link Budget button to calculate the link budget information 6 The link budget information will be displayed as shown below in Fig 5 9 The link budget information includes the EIRP Free Space Loss and Theoretical RSSI The Receive Sensitivity Maximum Transmit Power System Gain and Available Fa
25. L 3415 User Guide Page 15 of 61 intelligent wireless platform 2 3 Using the Configuration Pages The airClient TOTAL configuration system comprises several pages for configuring each parameter common navigation menu bar is provided at the top of each page for easy navigation as shown in the figure below Figure 2 5 smartBridges Networking Home Summary Information airClient TOTAL sB3415 03 Router mode LAN IP Mode Static IP System Name 5B3415 03 IP Address 192 168 0 225 Subnet Mask 255 255 255 0 Figure 2 5 airClient TOTAL Navigation Menu Bar The Navigation menu bar contains menu items that allow the user to go to different configuration pages The following table Table 2 2 summarizes the functions available for the menu item links Table 2 2 Description of Menus Menu Item Menu Sub items Description Displays read only summary page with Summary Information information such as LAN Settings WLAN Settings Wireless Settings DHCP Server Settings Virtual Server and Routing Table Entries Allows user to set system name of the unit IP Address and subnet mask on the wired side LAN Settings Allows the user to set the gateway if the unit is in Bridge Mode Note This is only applicable for 3415 03 model Home Allows user to set IP address mask gateway on the wireless side Allows user to Enable or Disable DNS WLAN Settings Passthrough Allows user to
26. N Settings The wireless parameters need to be configured to allow the airClient TOTAL unit to associate with an airPoint Nexus device or any other third party wireless access point Follow the steps below to configure the airClient TOTAL Router NAT Mode Wireless IP Settings parameters 1 From the navigation menu bar click on the Home WLAN Settings to set the wireless parameters for the unit The WLAN Settings screen will be displayed as shown below 2 Select the Dynamic checkbox if the IP address can be obtained automatically from the wireless link else select the Static checkbox to manually configure the wireless IP mask 3 For Static Connection Type enter the wireless IP Address Network Mask Gateway Address for the airClient TOTAL unit 4 For Dynamic Connection Type select the Connection Type as Dynamic When connection type is changed to Dynamic two buttons Request and Release will appear as shown below in Figure 2 16 Click on the Request button to get the dynamic IP addresses from the DHCP Server If the unit is associated IP addresses will appear in the IP Address Subnet Mask and Gateway Address fields Click on Release button to release the assigned IP addresses 5 To enable DNS Passthrough check the DNS Passthrough checkbox 6 Set the Primary Secondary DNS Server as required 7 Click on Save to apply the settings Home WLAN Setting airClient TOTAL sB3415 03 Router mode WLAN Setting IP Address
27. a wireless deployment Pre Installation Checklist for airClient TOTAL Organization Name Site Name State Zip Code Telephone Number Regulatory Standard to be followed FCC ETSI Frequency Band B3415 2 4GHz only Maximum Output Power as per the Regulatory Authority EIRP 100mW 1W 4W Latitude Deg Min Sec Longitude Deg Min Sec UPS Installed Yes No UPS specification if any KVA Line Voltage 90V 264V AC 50 60 Hz Near Line of Site between sites Yes No Height of tower Feet Meters Required Throughput Mbps Distance between sites Miles km Antenna Type Internal External Antenna Manufacturer smartBridges Other Gain of antenna dBi Antenna Polarization Horizontal Vertical Beam width of antenna Horizontal deg Vertical deg airClient TOTAL 3415 User Guide Page 7 of 61 Length of external cable connecting Radio and antenna intelligent wireless Feet meters platform Fade Margin taken into account for link budgeting Ideally between 15 to 20 dB Model of smartBridges airClient TOTAL equipment selected for a link Please refer to note below for selecting the right equipment sB3415 Grounding Earth to Neutral Voltage Length of the Ethernet cable required for powering the unit Ideally less than 2 Volts Feet meters Choose the best channel wh
28. al Port and the corresponding Global port that can be used to access this Local IP port through the wireless interface 4 Activate Deactivate the entry 5 Click Add to add the entry into the IP Port Forwarding Table This will result in an entry into the table as shown below 6 Add multiple entries to the port forwarding table if required 7 Click Tools Reboot to save all the settings The settings will be applied after the Reboot 8 Upon the reboot the total no of entries in this table will show up in Summary Information page as shown in Fig 2 24 Networking IP Port Forwarding airClient TOTAL sB3415 03 NAT mode Virtual Server defines the port mapping between Local Area Network and public network Virtual Server Protocol TCP x Local IP Address l Local Port L Global Port Status Activate lt j Add ID Local IP and Port Global Port Protocol Status 0 192 168 0 10 21 21 TCP Activated Edit Delete Note Any change in configurations will take effect after reboot Figure 2 23 airClient TOTAL IP Port Forwarding Table airClient TOTAL 3415 User Guide Page 37 of 61 a intelligent wireless platform Figure 2 24 IP Port Forwarding Table Entries on Summary Page Follow the steps below to edit or delete a port forwarding entry in the airClient TOTAL operating in NAT Mode irClient TO TAL 3415 User Guide
29. aximum 96 dBm If you are not able to see the graph please download the Sun JRE available at URL http java sun com j2se 1 5 0 download js Si Applet GraphDraw started vo Internet Figure 2 18c airClient TOTAL Association Status Graph Noise Floor is the measurement of the signal created from the sum of all the noise sources and unwanted signals within a measurement system Note Ifthe Status Graph window does not appear click on the Java link to download the JRE airClient TOTAL 3415 User Guide Page 33 of 61 intelligent wireless platform 2 10 3 DHCP Configurations The airClient TOTAL unit can be used as a DHCP server DHCP Dynamic Host Configuration Protocol allows a host to be automatically assigned a new IP address out of a pool of preconfigured IP addresses for the network This feature will only work when the unit is in Router or NAT operating mode Follow the steps below to configure the airClient TOTAL unit as a DHCP server di airClient TOTAL 3415 User Guide From the Navigation menu bar click on Networking DHCP to access the DHCP configuration Page Click on Enable DHCP Server button to open the DHCP Server settings page The DHCP Server screen will be displayed as shown below in Fig 2 19 Select System Define if you wish the system to assign the IP addresses Select User Define if you wish to assign the IP address from the IP Address Pool If setting is User Define enter the Start IP addres
30. below will appear for the WPA PSK settings 2 Select the Authentication Type as WPA PSK from the drop down menu 3 Enter the Key Entry Method as ASCII or HEX 4 Enter the WPA Shared Key in the Passphrase field 5 Select the Cipher as TKIP or AES Note AES cipher is only available in 3415 03 model 6 Click on Save and click on Tools Reboot to reboot the unit The settings will take effect after the reboot Note For the 3415 03 model WPA PSK security modes will only work when the airClient TOTAL unit is in Router NAT modes airClient TOTAL 3415 User Guide Page 42 of 61 intelligent wireless platform Radio Security airClient TOTAL sB3415 03 NAT mode Security Setting Security Mode Enable vi Authentication Type WPA PS v Key Entry Method ASCII vi Passphrase eocccccccce Cipher TKIP Reset Figure 2 30 airClient TOTAL Security WPA PSK Configuration Table 2 5 Security Settings for WPA PSK Page Items Descriptions WPA PSK is an extra strong encryption where encryption keys are automatically changed called rekeying and authenticated between devices after a specified period of time or after a specified number of packets has been transmitted WPA PSK WPA PSK is far superior to WEP and provides stronger protection for the home or SOHO users The process used to generate the encryption key is very rigorous and the re keying or key changing is done very quic
31. changed model name will appear in the top right corner of the web interface and it will now be possible to upload the changed model firmware to the unit Note The license key feature will not work if the MAC address of the unit is provided wrongly to the smartBridges Technical Support Staff Tools License Key airClient TOTAL sB3415 03 Router mode Enter License Key Save Reset Figure 5 10 airClient TOTAL Product License Key Input airClient TOTAL 3415 User Guide Page 56 of 61 5 10 intelligent wireless platform Link Budget Planning Link Budget Planning is a very useful tool for link budget estimation A GPS Calculator is provided in the Link Budget Planning Calculator page to calculate the distance between an airClient TOTAL unit and an access point To calculate the distance between the two follow the steps below 1 From the top navigation menu bar click on Tools Link Budget Planning The Link Budget Planning web page will appear as shown below in Fig 5 11 2 Enter the GPS co ordinates of Station 1 Latitude1 and Longitude1 and Station 2 Latitude 2 and Longitude 2 GPS co ordinates may be entered in DD MM SS or DD MM SS SS formats 3 Select the distance in units miles or kilometers 4 Clickthe Compute Distance button to calculate the distance between the two stations 5 The distance will be displayed in the Distance text box Tools Link Planning GPS Calculator
32. de Margin at various Link Speeds are also computed and displayed in a table The Ideal fade margin for a link is between 10 dB to 20 dB for a stable link base on the environmental condition of a region Fresnel Zone Clearance Required will also be displayed Distance from Root Device to Remote Device is miles v Please Select Device airPoint Nexus m Device airClient Nexus Radio Mode Low Band Radio Mode Low Band Tx Output Power dBm Tx Output 18 dBm 4 to 26 Power dBm 18 dBm 4 to 26 Antenna Gain dBi Antenna Gain dBi RF Cable Loss RF Cable Loss 3 Compute Link Budget EIRP 39 Free Space Loss 104 4 Theoretical RSSI dBm 44 Recommended minimum 75dem Available Fade Margin dBm 38 Fresnel Zone Clearance Required 14 10 feet Figure 5 12 airClient TOTAL Link Budget Planning Calculator Note For the SB3415 models the device can be selected as airClient NEXUS airClient TOTAL 3415 User Guide Page 58 of 61 intelligent wireless platform 5 11 Reboot The device would need to be rebooted in case any changes are to be made to the system or a new firmware is downloaded Click on Tools Reboot to reboot the unit A figure showing the countdown to 0 will appear as shown below during the Reboot process Tools Reboot airClient TOTAL sB3415 03 NAT mode Plea
33. e Key feature this default bandwidth can be enhanced to higher bandwidths depending upon the end user application needs There might also be a market need to convert an originally bought 3415 01 model to a 3415 03 model with Bridge Mode capabilities By default the cross up gradation between models is not allowed This means that the 3415 01 model cannot be loaded with a 3415 03 image It can only be upgraded to future software releases of the same model i e 3415 01 However if a special key is inserted it is possible to upgrade between models The license key is based on the MAC address of the device bandwidth desired for the upgrade and the model number name Follow the steps to convert between models or to enhance the unit to higher bandwidths 1 Go to Tools System Configuration to read the Local MAC address of the unit 2 Send the MAC Address of the unit model name of the unit and the bandwidth needed for the upgrade to smartBridges Technical Support Staff at support smartbridges com 3 The smartBridges Technical Support Staff will generate a unique license key based on these 3 parameters and pass the key via email 4 Click on Tools Product License Key to enter this unique license key and select the Save button to apply the settings 5 If the license key feature was desired for higher bandwidth the unit would be upgraded upon the reboot 6 If the license key feature was desired for the cross upgrade of models the
34. e Set to Static IP by default 8 System Name This is the user defined name of the unit LAN Settings IP Address Ethernet IP Address Subnet Mask Ethernet IP subnet Mask WLAN Type Static IP or Dynamic IP IP Address Wireless IP address WLAN Network mask Wireless IP Mask Settings Gateway Address Wireless IP Gateway DNS Server Primary DNS Server Secondary DNS Secondary DNS Server SSID Displays the SSID currently set for the device This is the public name of the wireless link Channel Displays the channel at which the Client is associated Association Status Displays Associated or Not Associated status Wireless Mode Wireless operating mode 802 11b 802 119 Security Mode Displays if security is Enabled or Disabled Wireless Authentication Open System Shared Key WPA PSK Settings Data Rate Mbps This indicates the rate at which the radio has been asked to operate by the user Transmit Power This is used to set the output power of the radio Preamble The radio preamble is a section of data at the head of a packet The preamble contains information that the radio needs when sending and receiving packets Slot Time This can be set to Long Short time or Short time DHCP Server DHCP Server Displays if DHCP Server is Enabled or Disabled Settings Address Pool Allows the Address Pool to be System defined or User defined Start Address The Starting address of the DHCP Client IP Address pool End Address The Ending address of the DHCP Client IP Address pool
35. e latest information on _ smartBridges http www smartbridges com airClient TOTAL 3415 User Guide products please visit our website at Page 10 of 61 intelligent wireless platform 2 airClient TOTAL Configuration The airClient TOTAL sB3415 01 and sB3415 02 can work in either Router or NAT mode The airClient TOTAL sB3415 03 can work in one of the three modes Bridge Router or NAT The procedures for configuring the various parameters in each mode are outlined in this chapter Some of the details on the technical terms acronyms and abbreviations used can be found in Appendix A 2 1 Administrator Login and License Agreement The airClient TOTAL unit comes with a pre configured default Ethernet wired side IP address 192 168 0 225 and subnet mask 255 255 255 0 This default device IP address should be used when accessing the device configuration management interface for the first time using a web browser The PC must be on the same subnet as the airClient TOTAL unit Follow the steps below to login as an Administrator to the web based configuration management interface 1 Connect the airClient TOTAL using the Power over Ethernet PoE to a PC or network via the ETH Ethernet port Please refer to the Quick Install Guide for more information on connections 2 Open a web browser on the PC type the default device IP address http 192 168 0 225 in the web browser address field and press the Enter key
36. eee 25 2 9 2 Radio Settings usanne vtec yaasiet aeeetit eaten ened 25 2 10 AIRCLIENT TOTAL ROUTER NAT CONFIGURATION ccceeeeeceeeeeeeeeeeeeseeeeeeeeneeeeeeeaes 27 2 10 1 LAN Settings svanen Lundsten bekke shoe eke eae Bae ake 27 2 10 2 WEAN Settings staket eidet tidende 29 2 10 3 DHCP Conttourations ne 34 2 10 4 DHCP Relay Configuration mmrsrrnnnrnnrrrnnrrnnrrnnnrnnrrnnnrnnnrnnnnrnnrnnnrrnnnnennnnnnn 36 2 10 5 IP Port Fonwardmg eee reece eee eee eee aaae etter ee etecaaeeeeeee tent 37 2 10 6 Routing Fable 0 3 cc0 iii i eee 38 2 11 SECURITAS 40 2 11 1 Open System Shared key 40 211 2 WPA PSK iaaa keeten eege deeg Ces 42 CHAPTER 3 WIRELESS SETTINGS AND BANDWIDTH CONTROLLER nonnnnnnvvnnnnnnnvnnnnnnnr 44 3 12 WIRELESS ETRINGER EE 44 3 2 BANDWIDTH GONTROL sura Ee Een Ee Ee eae 45 CHAPTER 4 TRAFFIC STATISTICS ccscccccsseccccccsasececececesstenstecceceesesencderescecseseetesauacetesanacecevecene 47 CHAPTER 5 TOOLS watch neh keke nih edda date eene eegne Eesen 48 5 1 SYSTEM CONEIGUDATION tnnt tEEEEEEE EEES EEEEE EEEE EEE Ennen E Eneee nnne 48 5 2 OSNTP SETTING havin e aaea aa as a aaar aaa aa Ee 49 5 3 SME SURVEY E 50 5 4 SYSTEM ADMIN irinin banna an a aaa a a a a N eae 51 5 5 SYSTEM USER gaai E a added Aa Aiai a AA a E Ea EA 51 5 6 SNMP CONFIGURATION ccceeeeceeeeeeeeeeeeeeaeeeeeeeaaeeeeseaeeeeseaeeeeeseaeeeeeeseeeeeeeneeeeessaas 51 Bil BACKUP RESTORE SETTLING Sivnttsave
37. elow to add a static route entry in the airClient TOTAL operating in the Router Mode 1 Click on Networking Routing Table from the menu bar to access the routing table page 2 Enter the Destination IP IP Mask Gateway for the new route Select Add to add a new route as shown in Fig 2 16 3 Select the Status to activate or deactivate the static route 4 Click on Tools Reboot to reboot the unit The new routes will be activated or deactivated after the Reboot 5 Upon the reboot the total number of entries in this Routing Table will show up in Summary Information page as shown in Fig 2 27 below Networking Routing Table airClient TOTAL sB3415 03 Router mode Routing Mode Selection 4 Save You can manually set a routing entry here Enter the destination IP address and its network mask and the IP of which port the packets are forwarded to Dest IP IP Mask Gateway Status Activate v ms Update o oaeen ID Destination IP IPMask Gateway Status oj 192 168 3 0 255 255 255 0 192 168 2 220 Activated Edit Delete 1 192 168 4 0 255 255 255 0 192 168 2 220 Activated Edit Delete Note Any change in configurations will take effect after reboot Figure 2 26 airClient TOTAL Add Static Route in Routing Table Routing Setting Static Routing Entries D Figure 2 27 Static Route Entries on Summary Page airClient TOTAL 3415 User Guide Page 39 of 61 intelligent
38. er is earlier fa the media on which the Software is furnished will be free of defects in materials and workmanship under normal use and Figure 2 2 airClient TOTAL License Agreement Page airClient TOTAL 3415 User Guide Page Dof l intelligent wireless platform Home Summary Information airClient TOTAL sB3415 03 NAT mode LAN Settings LAN IP Mode Static IP System Name 5B3415 03 IP Address 192 168 0 225 Subnet Mask WLAN Settings Wireless Settings NEXUS MASTER Channel Current Channel 6 2437MHz Not Associated 802 11g Association Status Wireless Mode Security Mode Disable Authentication Open System Data Rate Mbps Best msme Power rege Slot Time Short Slot Time DHCP Server Settings Address Pool System Define Start Address 0 0 0 0 End Address 0 0 0 0 te tine 2080 mini NAT Virtual Server 0 Entrifes Routing Setting Static Routing 0 Entrifes Figure 2 3 airClient TOTAL Summary Information Page airClient TOTAL 3415 User Guide Page 1307 61 intelligent wireless platform The descriptions of the fields in the Summary Information page are provided in the table Table 2 1 below Table 2 1 Description of the field items in the Summary Information page Field Items on Summary Info page Descriptions LAN IP Mod
39. guide the following related publications provide complete information on the TOTAL series airHaul airPoint and airClient of radio units e Quick Install Guide QIG e Release Notes e Technical Specification All the information can also be found on our website at http www smartbridges com Technical Support Center Comprehensive technical support by dedicated smartBridges engineers is available to all customers through the smartBridges support center website The website provides updated tools and documents to help troubleshoot and resolve technical issues related to smartBridges products and technologies To access the technical support resources please visit the support center website at http www smartbridges com support For additional services and free downloads you would need to register on the smartBridges support center website airClient TOTAL 3415 User Guide Page 5 of 61 intelligent wireless platform 1 Introduction This user manual will guide you through initial site preparation installation configuration and troubleshooting of the airClient TOTAL 241 sB3415 unit A web based management tool is provided to assist the user to configure the airClient TOTAL unit for different purposes The airClient TOTAL web based management tool provides the user with the following features System configuration Device operational mode configuration Ethernet and wireless IP configurations Radi
40. ich can be used with the help of the Site Survey Tool and scanning tools like Netstumbler Network diagram along with IP address of all the interfaces for link to be set up in place Specify channel number Yes No Availability of Quick Installation Guide Yes No Availability of User Guide and CD Yes No Ensure that all items listed in the Package Contents of Quick Installation Guide are included in the shipment Yes No Availability of Installation Kit Yes No Radio MAC address of Access Point MAC ID no Configured for pre installation testing Yes No Ping response ms Ping Success Rate Percentage Throughput test Upload Download sB3415 01 Varies depending on the Bandwidth Control signal strength link quality and distance As much as 512 kbps data throughput with a range of up to 4 miles 6 km sB3415 02 As much as 1 Mbps data throughput with a range of up to 4 miles 6 km B3415 03 As much as 3 Mbps data throughput with a range of upto 4 miles 6 km Signature of Engineer Name airClient TOTAL 3415 User Guide Page 8 of 61 Post Installation Checklist for airClient TOTAL Organization Name Site Name Address City State Zip Code Telephone Number Radio operation mode intelligent wireless platform sB3415 01 sB3415 02 Router NAT sB3415 03 Bridge Router NAT
41. intelligent wireless platform 2 5 Changing from NAT to Router Mode The default configuration of the airClient TOTAL is in the NAT mode Follow the steps below to change the airClient TOTAL from the default NAT mode to Router mode 1 From the navigation menu bar click on Tools System Configuration The System Configuration page will appear as shown below 2 Under the Current Operational Mode choose the operation mode Router 3 Click on Save to reboot the unit and convert to Router mode 4 The IP Address IP Mask and Gateway for LAN Settings and WLAN Settings remain the same in the Router mode as it was in the NAT mode System Configuration airClient TOTAL sB3415 03 NAT mode en Name 5B3415 03 SNMP SNMP Configuration SNMP Configuration Reset Reset Reset Reset SNTP Server SNTP Server Firmware Version 2 0 0B1P0 5B3415 03 Reset To Factory Defaults Reset to Defaults Ethernet MTU Size 1500bytes O Bridge NAT Figure 2 7 Changing NAT Mode to Router Mode airClient TOTAL 3415 User Guide Page 21 of 61 intelligent wireless platform 2 6 Changing from Router to NAT Mode Follow the steps below to change the airClient TOTAL from Router Mode to NAT Mode 1 From the navigation menu bar click on Tools System Configuration The System Configuration screen will appear as shown below 2 Under the Current Operational Mode choose the operation mode NAT 3 Click on Sa
42. ity airClient TOTAL 3415 User Guide Security Allows user to set the security mode for the device User can choose Open System Shared or WPA PSK Open System Shared Key e Allows Allow user to turn on encryption using WEP at 64 or 128 bits and choose between Open Systems and Shared Key e WPA PSK This mode allows user to use WPA pre shared key and cipher as TKIP or AES for client authentication Page 17 of 61 intelligent wireless platform Menu Item Menu Sub items Description Note By default the Security mode is Disabled AES security mode is only available in 3415 03 model Allows user to switch the operation System Contiouration mode between Bridge sB3415 03 ys 9 Only Router or NAT mode Allows the user to Reset the unit Restore unit to Factory defaults Allows user to set the Network Time SNP Settifig Server and the Time Zone Site Surve Shows all the standards based wireless y devices operating in the area Bieter Admih Allows user to change the Administrator y user name and or password Allows read only users to added and System User their user names passwords to be changed This allows the user to Enable Disable SNMP Configuration SNMP and set Read Write community strings Tools Backup Restore Settings Allows user to save or restore good settings backup the configuration file and upload it later do a Factory Reset on the unit
43. kly This stops even the most determined hacker from gathering enough data to break the encryption Key entry method can be HEX or ASCII To associate with the airPoint Key Entry Method Nexus device this value should be set to ASCII This key is used by the client to become authenticated with the airPoint Passphrase Nexus or any third party WPA capable device Cipher This can be set to TKIP or AES Note AES is only supported in 3415 03 model airClient TOTAL 3415 User Guide Page 43 of 61 intelligent wireless platform 3 Wireless Settings and Bandwidth Controller 3 1 Wireless Settings The Wireless Settings can be accessed from the Radio Wireless Settings in the navigation menu bar Radio Advanced Settings airClient TOTAL sB3415 03 Router mode Advanced Setting SSID NEXUS MASTER SSID suppressed Ces No Channel Remote AP MAC Address 00 00 00 00 00 00 Wireless Mode 2 4GHz 54Mbps 802 119 v Antenna Selection Internal O External Distance Within 1Km vi Country UNITED STATES US x Data Rate Mbps Best vi Default Data Rate Mbps A Ni Transmit Power 18 dBm E Preamble Long Preamble v Slot Time Short Slot Time Ji Ga Protection Mode None E Protection Type CTS only RTS CTS RTS CTS Threshold 2346 Reset Figure 3 1 airClient TOTAL Wireless Settings The followi
44. layed as shown in Fig 2 17 Set the SSID and the wireless mode to either 802 11 b g The Channel selection is disabled in the Router NAT mode The airClient unit once associated will follow the corresponding AP The Remote AP MAC Address can be set to 00 00 00 00 00 00 in case the association is only to based on the SSID Or the Remote AP MAC Address can be set to a specific AP MAC Address in case the airClient TOTAL unit needs to be associated with a specific Access Point For the Antenna Selection choose either Internal or External antenna as per the requirement Select the Country for the domain settings Configure the Distance parameter to configure the Ack Window Select the Data rate from the drop down menu By default the data rate is set to Best Select the Transmit power of the radio from the drop down menu Select the Preamble to be Long or Short By default the preamble is set to Long Click on Save to reboot and for the settings to take effect The unit will attempt to associate after the Reboot The Association Status field in the Wireless Settings of the Summary Information page will show the status as Associated if the unit has associated successfully as shown in Fig 2 18a below Under Networking Association Status the status will also show the Access Point that the client is associated with as shown in Fig 2 18b below Click on Show Graph on this table to view the Association Status Graph as shown in Fig
45. ng table summarizes the information for the wireless settings Table 2 3 Wireless Settings Page Items Descriptions SSID The network name for the wireless network SSID Suppressed Shows if the SSID Suppressed is Enable or Disabled This is not selectable in the current Router NAT device configuration The client will follow the channel of the AP to be Channel associated with The channel has to be set in the Bridge Mode configuration SB3415 03 only This is the MAC address of the remote Access Point This has to be set in Bridge Mode configuration sB3415 03 only airClient TOTAL 3415 User Guide Page 44 of 61 Remote AP MAC Address intelligent wireless platform Page Items Descriptions This is the radio operating mode of the client This can be set to the wireless 802 11b or 802 119 Wireless Mode Antenna Selection This sets the Antenna to Internal or External Distance The range of the link which corresponds to ACK window size This allows the selection of a country to change the radio Country regulatory domain This rate at which the operator wants radio to operate Data Rate By default this rate is set to Best Data rate for transmitting beacons broadcast and multicast packets By default this rate is set to 1 Mbps Default Data Rate This is used to set the output power of the radio Transmit Power The valid radio power range is from 0 to 18 dBm
46. o parameter configuration Bandwidth management Traffic Statistics Site Survey Security User Management Link Budget Planning Calculator Upgrading the unit to higher bandwidth using License Key Converting from one model of sB3415 to another using License Key Saving Restoring good configuration settings Restore to Default settings Firmware Upgrade Note Unless specifically stated the configurations mentioned in the user guide are applicable to all the models of SB3415 SB3415 01 sB3415 02 sB3415 03 1 1 System Requirements The following are the minimum system requirements for the airClient TOTAL web based configuration management tool 1 Operating System Windows 98 2000 XP NT or Linux 2 Connection to the Internet for downloading the latest firmware and Sun JRE 3 Web browser either Internet Explorer 5 0 and higher Netscape 7 2 and higher Mozilla 1 7 and higher or Mozilla Firefox 0 8 and higher 4 SUN JRE v1 5 and above You may download it from http java sun com j2se 1 5 0 download jsp airClient TOTAL 3415 User Guide Page 6of 61 1 2 Checklists intelligent wireless platform Deployment time link up time and support time can be improved by adopting proper site Survey analysis link planning pre installation tests and web GUI familiarization The following pre installation and post installation checklist attempts to give the installer the basic understanding on the points to consider for
47. or airClient TOTAL is available for download from the smartBridges support website at http www smartbridges com support aCT241 asp Follow the steps below to upgrade the airClient TOTAL firmware 1 Download the latest or a particular release version of the airClient TOTAL firmware from the web URL http Awww smartbridges com support aCT241 asp for sB3415 2 Unzip the downloaded file to get firmware file with the name eg sB3415 03_v200B1P0 The prefix is the model name of the airClient TOTAL sB3415 01 sB3415 02 sB3415 03 The suffix is the firmware version no 3 Login to the device web interface Click on Tools Firmware Upgrade from the drop down menu The Firmware Upgrade page will be displayed as shown below 4 Use the Browse button to select the location of this firmware file 5 Click on the Upload button to upload the firmware Wait for around 60 seconds to allow the new firmware to be uploaded to the unit 6 When the firmware file transfer is completed successfully a message will be displayed on the web page as shown in Fig 5 9 7 Reboot the unit by clicking Tools Reboot for the new firmware to take effect Note The new firmware will take effect only after the reboot Note During the upgrade period about 1 minute the airClient TOTAL unit MUST NOT be reset or power cycled Improper actions can damage the unit Tools Firmware Upgrade airClient TOTAL sB3415 03 NAT mode Attention Please u
48. ormation Page Networking Association Status airClient TOTAL sB3415 03 Bridge mode Signal ID MAC Address Status Strength RSSI NoiseFloor WERTEN ER a Show 0 00 02 6F 44 18 67 up 89 dBm 96 dBm raph Refresh Figure 2 13b airClient TOTAL Wireless Association Status 2 10 airClient TOTAL Router NAT Configuration This section covers the procedures for configuring various parameters in the Router and NAT modes 2 10 1 LAN Settings The LAN and the WLAN settings are maintained in two different subnets Follow the steps below to re configure the airClient TOTAL Router NAT Ethernet parameters 1 From the navigation menu bar click on Home LAN Settings to change Ethernet wired side parameters The LAN Settings screen will appear as shown below 2 Enter the System Name of the unit if required 3 Enter the IP address and Subnet mask to set the LAN IP address and subnet mask 4 Click on Save to apply the settings airClient TOTAL 3415 User Guide Page 27 of 61 intelligent wireless platform Home LAN Setting airClient TOTAL sB3415 03 Router mode LAN Setting IP Mode Static IP Dynamic IP DHCP IP Address 192 168 0 225 Subnet Mask 255 255 255 0 Reset Figure 2 14 airClient TOTAL Router NAT LAN Settings airClient TOTAL 3415 User Guide Page 28 of 61 intelligent wireless platform 2 10 2 WLA
49. otal Bytes Receive Total no of bytes received on the wireless interface Total Bytes Transmit Total no of bytes transmitted on the wireless interface Broadcast Packets Receive Total no of broadcast packets received Broadcast Packets Transmit Total no of broadcast packets transmitted Multicast Packets Receive Total no of multicast packets received Multicast Packets Transmit Total no of multicast packets transmitted e i Total no of unicast packets received from a specific Unicast Packets Receive destination Total no of unicast packets transmitted to a specific Unicast Packets Transmit destination Up Time Displays the time since the last reboot of the device airClient TOTAL 3415 User Guide Page 47 of 61 intelligent wireless platform 5 Tools In this section you will find relevant information for changing the operating mode of the device saving the configuration restoring to factory defaults and upgrading the firmware 5 1 System Configuration The System Configuration page allows the user to change the operating mode of the unit Click on Tools System Configuration from the navigation menu bar to access the System Configuration page The following figure displays the System Configuration page System Configuration airClient TOTAL sB3415 03 NAT mode System Name 583415 03 SNMP Configuration SNMP Configuration
50. pload the correct firmware Please DO NOT power off or disconnect during uploading Improper actions will damage the system Please DO NOT close the browser during uploading Upload will take around 1 minute File Name Browse Current Version 2 0 082 0_S834i5 03 Upload Figure 5 7 airClient TOTAL Firmware Upgrade page airClient TOTAL 3415 User Guide Page 54 of 61 intelligent wireless platform Tools Firmware Upgrade airClient TOTAL sB3415 03 NAT mode Attention Please upload the correct firmware Please DO NOT power off or disconnect during uploading Improper actions will damage the system Please DO NOT close the browser during uploading Upload will take around 1 minute Figure 5 8 airClient TOTAL Firmware Upgrade Tools Firmware Upgrade airClient TOTAL sB3415 03 NAT mode Post Completed Upload Succeeds The file has been uploaded Back Figure 5 9 airClient TOTAL Successful Firmware Upgrade message airClient TOTAL 3415 User Guide Page 55 of 61 intelligent wireless platform 5 9 Product License Key This feature is used to enhance upgrade the default bandwidth on the airClient TOTAL units and to convert the models between sB3415 01 sB3415 02 and sB3415 03 By default the 3415 01 allows a maximum bandwidth of 512 kbps 3415 02 allows a bandwidth of 1 Mbps and 3415 03 allows a bandwidth of 3 Mbps Using the Product Licens
51. s Disabled 2 11 1 Open System Shared Key airClient TOTAL 3415 User Guide Page 40 of 61 intelligent wireless platform Open System Shared Key authentication is used for security between the airClient TOTAL and the airPoint Nexus or any other access point To enable disable or change security settings the user needs to access the security setting page on the web interface The following table describes the information for the security settings for the Open System or Shared Key authentication Follow the steps below to configure the Data Encryption parameters 1 Click on Radio Security from the main menu and a screen as shown in Fig 2 19 will be displayed 2 Choose the Authentication Type as Open System or Shared Key in the drop down menu 3 Choose the Key Entry Method as HEX or ASCII Key should be HEX when trying to associate with the airPoint Nexus Access Point 4 Choose the Key length 64 bits or 128 bits from the drop down list For HEX entry method Key length is 10 characters for 64 bits and 26 characters for 128 bits 5 Enter the WEP key in the Key Table entries 6 Select the Key ID of the index of the key to be used to associate 7 Click Save to save the settings 8 Select Tools Reboot to reboot the unit The settings will be effective after the reboot Radio Security airClient TOTAL sB3415 03 NAT mode Security Setting Security Mode Enable vi Authentication Type Open System Y
52. s and an End IP Address for the IP pool range that can be assigned to a DHCP client Note that the Start and End IP address have to be in the same network segment as of the Ethernet IP address segment In case you require to reserve certain IP addresses for known devices enter the corresponding MAG and IP address in the DHCP server reserved entries table Enter the lease time in minutes The maximum lease time that is allowed is 2880 minutes Click on Save to apply the settings The revised DHCP settings will show up in the Summary Information page of the unit If any DHCP client is added it will appear in the Networking DHCP List as shown below in Fig 2 20 Page 34 of 61 intelligent wireless platform Networking DHCP Server airClient TOTAL sB3415 03 Router mode DHCP Server Setting DHCP Server provides automation and control of IP address assignment services Enable DHCP Server O Enable DHCP Relay Disable DHCP and DHCP Relay IP Address Pool O system Define User Define Start Address 1192 168 0 50 End Address 192 168 0 80 Lease Time 2880 Minutes 1 2880Min DHCP Server Reserved Entries Please fill up by order MAC Address IP Address EE Save Reset Figure 2 19 airClient TOTAL DHCP Server Configurations Networking DHCP List airClient TOTAL sB3415 03 Router mode DHCP Server List ID MA
53. s mandatory to set the MAC Address of the Remote AP and the Channel when the unit is converted from Router NAT mode to the Bridge Mode System Configuration airClient TOTAL sB3415 03 Router mode System Name 58341 5 03 SNMP Configuration SNMP Configuration Reset Reset SNTP Server SNTP Server Firmware Version 2 0 0B1P0 5B3415 03 Local MAC Address 00 06 c7 01 03 08 Reset To Factory Defaults Reset to Defaults Ethernet MTU Size 1500bytes System Log Syslog Bridge Router Figure 2 9 Changing Router NAT Mode to Bridge Mode sB3415 03 only 2 8 Changing from Bridge to Router NAT Mode sB3415 03 Only This section is only valid for the sB3415 03 model Follow the steps below to change the airClient TOTAL from the Bridge mode to Router NAT mode 1 From the navigation menu bar click on Tools System Configuration The Operation Mode screen will appear as shown below 2 Under the Current Operational Mode settings choose Router or NAT option 3 Click on Save to reboot the unit and to convert the unit to Router NAT mode 4 Toconfigure the Wired parameters see Section 2 10 1 5 Toconfigure the WLAN IP and Radio parameters like SSID see Section 2 10 2 airClient TOTAL 3415 User Guide Page 23 of 61 intelligent wireless platform System Configuration airClient TOTAL sB3415 03 Bridge mode System Name 5B3415 03 SNMP Configuration SNMP Configuration
54. se wait while the system is Rebooting 25 Figure 5 13 airClient TOTAL Reboot page Note The reboot may take around 30 seconds to complete Once the reboot is complete click Here on the following screen to get the last page prior to the reboot Tools Reboot airClient TOTAL sB3415 03 NAT mode Please Click Here To Continue Figure 5 14 airClient TOTAL Reboot page 2 This concludes the user guide For the latest updates tools and documents to help troubleshoot the B3415 visit the support section of the smartBridges website at http www smartbridges com Support airClient TOTAL 3415 User Guide Page 59 of 61 intelligent wireless platform Appendix A Some useful terms and definitions Acronyms and Abbreviations MAG Media Access Control RSSI Receive Signal Sensitivity Indication SSID Service Set Identifier DHCP Dynamic Host Configuration Protocol ACL Access Control List SNMP Simple Network Management Protocol SNTP Simple Network Time Protocol STP Spanning Tree Protocol TCP Transmission Control Protocol IP Internet Protocol WDS Wireless Distribution System SSID Each ESS has a Service Set Identifier SSID used to identify the Radio that belongs to the ESS Radios can be configured with the SSID of the ESS to which they should associate By default radios broadcast their SSID to advertise their presence WDS Wireless Distribution System WDS is a sys
55. smartBridges to the future unwiring our world oy airClient TOTAL 241 Series B3415 01 SB3415 02 sB3415 03 User Guide Version 2 0 Copyright smartBridges Pte Ltd All Rights Reserved intelligent wireless platform CONTENTS ABOUT THIS DOCUMENT 2 32 22 adada LEE Ree RE RAE BALE Ai Ride 4 Overview of User Guide 00 cccccccceccccceeeeceeeeeeeaeeeeeeaeeeeeeeaeeeeeeeaaeeeeseaeeeeseeeeeeseeneeeeess 4 Related Publications 5 Technical Support Center 5 CHAPTER 1 INTRODUCTION bebes esse seet wach ec cent en nena ea ce st oeandkdennnnensnenenenbnnnekaenaekdeke 6 LJ OSYSTEM REQUIREMENTS dere deed deed 6 12 e REH 7 CHAPTER 2 AIRCLIENT TOTAL CONFIGURATION rrnnnnnvvnnnnnnvvnnnnnnnvnnnnnnnvnnnnnnnnnnnnnnnnnnnnnnnnn 11 2 1 ADMINISTRATOR LOGIN AND LICENSE AGPBEEMENT 11 2 2 WEB GUI ADMINISTRATOR USER NAME AND PASSWORD CHANGE sssssssssressrrrrssrrrreeere 15 2 3 USING THE CONFIGURATION PAGES ranrrnnnrnnvrnnnnnnnvnnnnrnnnrnnnrnnrrnnnrrnnnnennrnnnnnennnnnrnnnnnnnnnnnn 16 2 4 DEVICE MODE CONFIGURATION cccceceeeeeeeeeeeeeeceeeeeeeeeeeeeaeeeeseaeeeeseeeeeeeseneeeesenaeees 20 2 5 CHANGING FROM NAT TO ROUTER Mon 21 2 6 CHANGING FROM ROUTER TO NAT Mon 22 2 7 CHANGING FROM ROUTER NAT TO BRIDGE MODE SB3415 03 ONGe 22 2 8 CHANGING FROM BRIDGE TO ROUTER NAT MODE SB3415 03 ONGe 23 2 9 AIRCLIENT TOTAL BRIDGE CONFIGURATION SB3415 03 ON 25 2 9 1 RE dl chien Jeera nid tate dainty ii
56. tem that provides a means to extend the range of Wireless Local Area Network It allows the creation of large wireless networks by linking several wireless stations with WDS links To create a WDS link peer MAC addresses need to be exchanged as can be done through the Wireless Settings page for 3415 03 Bridge Mode All stations in WDS should be configured to use the same radio channel and share the same WEP keys if they are used smartBridges radios functions as a transparent bridge while operating as WDS links WEP According to the IEEE 802 11 standard Wired Equivalent Privacy WEP is intended to provide confidentiality that is subjectively equivalent to the confidentiality of a wired local area network medium and that does not employ cryptographic techniques to enhance privacy WEP relies on a secret key that is shared between a mobile station and an access point WEP uses the RC4 stream cipher invented by RSA Data Security RC4 is a symmetric stream cipher that uses the same variable length key for encryption and decryption With WEP enabled the sender encrypts the data frame payload and replaces the original payload with the encrypted payload The sender then forwards the encrypted frame to its destination The encrypted data frames are sent with the MAC header WEP bit set Thus the receiver knows to use the shared WEP key to decrypt the payload and recover the original frame The new frame with an unencrypted payload can then be passed
57. to get their TCP IP networking settings from a central server Importantly DHCP assigns IP addresses and other TCP IP configuration parameters automatically SNMP Short for Simple Network Management Protocol a set of protocols for managing complex networks The first versions of SNMP were developed in the early 80s SNMP works by sending messages called protocol data units PDUs to different parts of a network SNMP compliant devices called agents store data about themselves in Management Information Bases MIB and return this data to the SNMP requesters SYSLOG In order to track information on events device jobs and packets flows most security devices out put these events using the syslog information model airClient TOTAL 3415 User Guide Page 61 of 61
58. ttings Follow the steps below to configure the Radio parameters in the airClient TOTAL Bridge Mode 1 From the navigation menu bar click on Radio Wireless Settings to set the radio parameters The Wireless Settings screen will be displayed as shown in Fig 2 12 2 Setthe SSID and the wireless mode to either 802 11 b g 3 Enter the MAC address of the remote AP Note This is mandatory to set when the unit is converted to Bridge Mode 4 Setthe Channel to the channel setting of the Access Point Note This is mandatory to set when the unit is converted to Bridge Mode airClient TOTAL 3415 User Guide Page 25 of 61 intelligent wireless platform 5 Forthe Antenna Selection choose either Internal or External antenna as per the requirement 6 Select the Country for the domain settings 7 Configure the Distance parameter to configure the Ack Window 8 Select the Data Rate from the drop down menu By default the data rate is set to Best 9 Set the Default Data Rate to set the data rate for transmitting beacons broadcast and multicast traffic By default this rate is set to 1 Mbps 10 Select the Transmit power of the radio from the drop down menu 11 Select the Preamble to be Long or Short By default the preamble is set to Long 12 Click on Save to reboot and for the settings to take effect The unit will attempt to associate after the Reboot Note The Association Status field in the Wireless Settings of the
59. unit A page will appear as shown below 2 Click on the Save button to save the current good settings of the system 3 In the event the unit needs to be restored select the Restore amp Reboot button to recover the settings of unit that was saved earlier This action will also reboot the system for the new settings to take effect 4 The user can also save the current settings of the system to the PC through the Ethernet interface Click on Here to save the options to a PC 5 The saved file can be used to restore the system at a later time Note The system will currently only allow a file with the name apcfg to be uploaded 6 By clicking the FactoryReset amp Reboot button the unit will reset and go back to the factory defaults Tools Backup Restore Settings airClient TOTAL sB3415 03 NAT mode Good Settings Save the Good Settings Restore to the Good Settings Restore amp Reboot Configuration File Backup the current settings to a file Click Here to save Upload the Configuration File apefg Upload Factory Reset Press the button to set all the configurations to factory default settings Factory Reset amp Reboot Figure 5 6 airClient TOTAL Backup Restore Settings airClient TOTAL 3415 User Guide Page 53 of 61 intelligent wireless platform 5 8 Firmware Upgrade The airClient TOTAL unit firmware can be upgraded from the web management interface The latest firmware f
60. utton Select a different SSID and select on the Save button to move to another AP Refresh button Refreshes the Site Survey page airClient TOTAL 3415 User Guide Page 50 of 61 intelligent wireless platform 5 4 System Admin This menu option allows the user to change the User Name and or password to access the unit Refer to chapter 2 2 to change the user name and or administrator password The default user name is administrator and the default password is smartBridges case sensitive 5 5 System User The airClient TOTAL unit allows the user to create Read Only users to only allow the users to only view the configurations of the unit This Read Only user cannot edit any configurations and cannot reboot the unit or restore the unit to factory default settings This menu option allows the user to change the Read Only user name and or password to access the unit Follow the steps here to change the user name and or password for this Read Only User 1 From the top navigation menu bar click on Tools System User A System User interface will appear as shown below 2 Enter the user name you wish in the Common User field 3 Enter the new password in Password and Verify Password fields Click on the Save button to save the settings 4 Click on the Save button to save the settings Tools System User airClient TOTAL sB3415 03 Router mode Common User Name user Password
61. ve to reboot the unit and convert to NAT mode 4 The IP Address IP Mask and Gateway for Ethernet Configuration and Wireless Configuration remains the same in the NAT mode as it was in the Router mode System Configuration airClient TOTAL sB3415 03 Router mode System Configuration System Name SB341 5 03 SNMP Configuration SNMP Configuration Reset Reset SNTP Server SNTP Server Firmware Version 2 0 0B1P0 5B3415 03 Local MAC Address 00 06 c7 01 03 08 Reset To Factory Defaults Reset to Defaults Ethernet MTU Size 1500bytes System Log Syslog Current Operational Mode p O Bridge O Router Figure 2 8 Changing Router Mode to NAT Mode 2 7 Changing from Router NAT to Bridge Mode sB3415 03 Only This section is only valid for the sB3415 03 model Follow the steps below to change the airClient TOTAL from the Router or NAT mode to Bridge mode 1 From the navigation menu bar click on Tools System Configuration The System Configuration screen will appear as shown below 2 Under the Current Operational Mode settings choose Bridge option 3 Click on Save to convert the unit to Bridge mode airClient TOTAL 3415 User Guide Page 22 of 61 intelligent wireless platform 4 To configure the IP settings in Bridge mode refer to Section 2 9 1 5 To configure the Radio Settings in Bridge mode refer to Section 2 9 2 Note It
62. veseatvavesestvevestatitwentnti tannin AEN 53 5 8 FIRMWARE UPGRADE ssssssessketseitnetttt nteti ttnet ttn SttEAnEEEEEEEEEEEEEEEEEEEENEEEAEE EEEE EEEE EnEn E Eneee 54 5 9 PRODUCT LICENSE KE Ving 56 airClient TOTAL 3415 User Guide Page 2 of 61 intelligent wireless platform 5 10 LINK BUDGET PLANNING rrrrrrrrrvrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrnrrsrrnnrrrrrrrrrrrnrrrrrrrrrrrrrrrrrnrnnnnnnnn 57 Sili REBOOT Ls 59 APPENDIX A SOME USEFUL TERMS AND DEFINITIONS Qsnvennnnvennnvvnnnnvnnnnvnnnnvennnnvennnnennnnn 60 airClient TOTAL 3415 User Guide Page 3 of 61 intelligent wireless platform Congratulations on your purchase of sB product Your airClient TOTAL 241 unit is designed so that you can set it up easily and be on your way to get unwired Important Read all user instructions carefully before you use your device About This Document This user guide is for the networking professional who installs configures and manages the smartBridges airClient TOTAL 241 series Unless specifically stated the configurations mentioned in the user guide are applicable to all the models of SB3415 SB3415 01 SsB3415 02 sB3415 03 It provides detailed information on using the web based configuration Graphics User Interface GUI to configure the airClient TOTAL sB3415 unit This manual will help you gain a better understanding of how the various components of the sB3415 work To configure smartBridges products

2060 KB - R-One Trading

Contents

Download Pdf Manuals

Related Search

Related Contents