4D-3300 Manual - Perma Pure LLC
Contents
1. I e emnes mense eme en hen nnne nnns 10 Pressure Sensor Model 3300P REA X EXER ARRA ARR Ea 10 Troubleshooting and Maintenance cece cece eee eee 11 Replacemient parts deca et x vault ERE E ah as ERREUR PARERE RM REESE AER 12 Appendix A Flow Control Drawer Drawings 13 A1 Panel drawing i rte HE TA EVENT E 13 A2 Flow schematic eoe dete REN EU EK 13 Appendix B Warranty and Disclaimer 14 Model 3300 User s Manual PERMA PURE LLG Doc 532 Revision 000 HALMA Page 3 of 14 Unpacking Perma Pure has made every effort to ship you a high quality product that has been thoroughly inspected and tested It has been carefully packed to ensure that it arrives at your facility in good condition Even though every effort has been made to prevent damage during the transportation process damage can occur by the carrier This is out of control of Perma Pure and is the responsibility of the carrier to ensure that your equipment arrives intact and undamaged Inspect outside packaging If there is any visible damage inform the carrier at the time of deliver This inspection is important Once the package is signed for responsibility for any visible damage then tra2. SHEET OF 1 DENOTES MILLIMETER EQUIVALENTS WHEN USED Model 3300 User s Manual b Doc 532 Revision 000 PERMA PURE LLG Page 14 of 14 HALMA Appendix B Warranty and Disclaimer Perma Pure LLC Perma Pure Seller warrants that product supplied hereunder shall at the time of delivery to Buyer conform to the published specifications of Seller and be free from defects in material and workmanship under normal use and service Seller s sole obligation and liability under this warranty is limited to the repair or replacement at its factory at Seller s option of any such product which proves defective within one year after the date of original shipment from seller s factory or for a normal usable lifetime if the product is a disposable or expendable item and is found to be defective in material or workmanship by Seller s inspection Buyer agrees that 1 any technical advice information suggestions or recommendations given to Buyer by Seller or any representative of Seller with respect to the product or the suitability or desirability of the product for an particular use or application are based solely on the general knowledge of Seller are intended for information guidance only and do not constitute any representation or warranty by Seller that the product shall in fact be suitable or desirable for any particular use or application 2 Buyer takes sole responsibility for the use and applications to
3. CH3 Analyzer 4 CH4 Analyzer 5 CH5 Analyzer 6 CH6 Calibration Gas 1 14 CG1 8 COPYRI GHT 2008 ALL RIGHTS RESERVED Original Instructions Model 3300 User s Manual b Doc 532 Revision 000 PERMA PURE LLG Page 6 of 14 HALMA Important Safety Warnings Please be sure to review the following basic safety procedures These procedures represent the MI NI MUM requirements to operate the equipment safely It is the ultimate responsibility of the operator to ensure proper safety practices are utilized at the point of operation e NEVER attempt to operate this equipment in an explosive or otherwise hazardous area e NEVER exceed any specified rating for the equipment Voltage temperature and pressure ratings must be closely observed and not exceeded Voltage rating of the equipment MUST match the rating on the data label Please make sure that it matches before powering up the equipment e This equipment is NOT designed to be used in an explosive environment e This equipment is NOT designed to operate in a wet environment e Sample gas is potentially dangerous A leak test is recommended at initial startup and as often as necessary to maintain a safe working environment around the equipment The gas stream exhaust must exit away fro
4. Model 3300 User s Manual b Doc 532 Revision 000 PERMA PURE LLG Page 4 of 14 HALMA COMPAN General description The Baldwin Series Model 3300 Flow Control Drawer allows easy control of sample and calibration gases With the Model 3300 you may choose whether to control sample gases cal gases and stack probe blowback manually or by PLC The standard Model 3300 is configured for two gas channels and two calibration gases zero and span Manual control switches are provided for selection of system or direct calibration Four flow meters are included for visual indication amp control of stack calibration gas flow individual analyzer flow and bypass Model 3300 has a provision for system bias checks System integrity is verified by comparing the calibration gas flow to the stack filter head and through the entire sample system to the calibration gas introduced directly to the continuous gas analyzer common sample manifold This check indicates problems such as system leakage and gas component loss Features e Manual or PLC control of sample amp calibration gases Up to 6 gas analyzer channels Up to 8 cal gas channels including zero and span Multiple flow meters cal gas to probe total flow to analyzers individual analyzer channels Pump vacuum gauge Sample cal gas pressure gauge Cal gas regulator Optional pressure transmitters Model 3300P The Model 3300 Flow Control Drawer is a 19 Rack Mountable integrated ga
5. the analyzer suite will be protected from blowback pressurization Computer Control Mode Operation Computer Control CC To enter Computer Control mode operation the Remote Local switch must be toggled to the left Computer control is initiated through the 16 Position vertical terminal block on the back panel To activate a particular function 5VDC is applied to the appropriate terminal The Remote and Local functions are identical This can be done in one of two ways The first way is to take the 5 VDC from terminal 10 or 12 pass it through a set of dry contacts on a computer controlled relay and back to the appropriate terminal The second way is to take 5VDC directly from the computer control to the appropriate terminal For this method please note that the flow control drawer GND on Terminal 14 and 16 must be connected to the GND on the computer control unit to electrically reference both systems together Model 3300 User s Manual PERMA PURE LLG Doc 532 Revision 000 4 HALMA COMPANY Page 9 of 14 Computer Control Terminals Summary Terminal 2 System Calibration Terminal 1 Cal Gas 1 Terminal 4 Direct Calibration Terminal 3 Gas 2 Terminal 6 Blowback Terminal 5 Cal Gas 3 Terminal 8 NA Terminal 7 Cal Gas 4 Terminal 10 5 VDC Terminal 9 CalGas 5 Terminal 12 5 VDC Terminal 11 Cal Gas 6 Terminal 14 GND Terminal 13 Cal Gas 7 Terminal 16 GND Terminal 15 Cal Gas 8 Computer Sense CS Alo
6. CER TERMINALS PRESSURE OUTPUTS PS1 0 15PSIG VACUUM PS4 0 30PSIG SAMPLE PRESS PS5 0 30PSIG CAL GAS PRESS TERMINALS 1 2 TERMINALS 7 8 TERMINALS 9 10 1 CALIBRATION GAS INLETS 2 CG 3 CG 4 5 CG 6 BALDWIN ENVIRONMENTAL Soo Flow Controlle Model 1500 3 7 8 00000000Q OOOOOOOOOO OOOOOOOO00 115 VAC 5A USE ONLY WITH 100v O 250 FUSES 120V 230V0 DISCONNECT POWER 240VO BEFORE REPLACING FUSES COMPUTER CONTROL TERMINALS Activated 5vdc TERMINAL FUNCTION CAL GAS VALVE CG1 SYSTEM CALIBRATION CAL GAS VALVE CG2 DIRECT CALIBRATION CAL GAS VALVE CG3 BLOWBACK CAL GAS VALVE CG4 NA CAL GAS VALVE CG5 5 VDC CAL GAS VALVE CG6 5 VDC CAL GAS VALVE CG7 GROUND GND CAL GAS VALVE CG8 GROUND GND CURRENT OUTPUTS 4 20 mAdc Odd numbered terminals are 24vdc inputs LOOP POWERED CURRENT OUTPUTS REQUIRES EXTERNAL 24VDC FROM REMOTE READOUT DEVICE O SAMPLE GAS CONNECTIONS NOTE The 5vdc used to activate computer control functions may be taken from terminals 10 amp 12 and run through dry contacts on a PLC and back to the desired function terminal the 4 5vdc may be supplied by the PLC directly if the PLC ground reference is tied together with the ground reference found on terminals 14 amp 16 Note thot these ground references are NOT earth ground Even numbered terminals are 4 20 mA outputs UNLESS OTHE
7. F 005 Pressure regulator 0 30 psig aluminum 2VSB 001 2 way solenoid valve 12 VDC 2VSB 002 3 way solenoid valve 12 VDC 2FTS 021 Cal Gas connector 3DCB 006 Circuit board switch board FCD 4D 3300P 2FTS 021 Cal Gas connector 3DCB 006 Circuit board switch board FCD 2FIV 003 Flow meter 0 1 10 LPM w valve 2FIN 002 Flow meter 0 1 10 LPM no valve 2FIV 005 Flow meter 0 2 2 5 LPM w valve 1PSD 032 Power supply 100W 12VDC 2GAP 006 Pressure gauge 2 1 2 dia Face 2RPF 005 Pressure regulator 0 30 psig aluminum 2VSB 001 2 way solenoid valve 12 VDC 2VSB 002 3 way solenoid valve 12 VDC 2FTS 021 Cal Gas connector 3DCB 006 Circuit board switch board FCD 2FIV 003 Flow meter 0 1 10 LPM w valve Model 3300 User s Manual PERMA PURE LLG Doc 532 Revision 000 HALMA COMPANY Page 13 of 14 A endix A Flow Control Drawer Drawings A1 Panel drawing A2 Flow schematic COPYRI GHT 2008 ALL RIGHTS RESERVED Original Instructions COMPUTER OOOOOOOO Aarorvnawao OOOOOOOO COMPUTER CONTROL PRESSURE TRANSDUCER BLOWBACK BACKPANEL TERMINAL CONNECTIONS COMPUTER SENSE TERMINALS DRY CONTACTS TERMINAL PAIR FUNCTION CAL GAS VALVE CG1 CAL GAS VALVE CG2 CAL GAS VALVE CG3 CAL GAS VALVE CG4 CAL GAS VALVE CG5 CAL GAS VALVE CG6 CAL GAS VALVE CG7 CAL GAS VALVE CG8 SYSTEM CALIBRATION DIRECT CALIBRATION BLOW BACK NORMALLY CLOSED LOCAL MODE NORMALLY CLOSED PRESSURE TRANSDU
8. PERMA PURE LLG Baldwin Series Model 3300 3300P Flow Control Drawer User s Manual PERMA PURE LLG COMPANY 8 Executive Drive Box 2105 Toms River 08754 732 244 0010 800 337 3762 fax 732 244 8140 www permapure com info permapure com Model 3300 User s Manual b Doc 532 Revision 000 PERMA PURE LLG Page 2 of 14 HALMA CO Contents 3 General description IRR Rn OE EROR ROGA T EUR UR UG UO CURE BR RR CRURA 4 Physical descriptlOn iui irr x XA E FA 5 SPECI CAtlOM ETE ETE aaa de 5 eret EET 5 Important Safety Warnings enne nnns annnm annee nnne EEE 6 Operation EET E ERU EVENT VEU HER CURE ERR VERA Y 7 Pressure Sensor Board Option sene 7 Local Mode Operation erre Ie pe ena eu Rao IVA VEDR ER ED VER KE YVVATE VES CUT E UE UR 8 Computer Control Mode Operation cine esee nean ne nia nu xa a a e d nd aan aa 8 Computer Control Terminals Summary 0 cece cece nennen amens nnn nnne nnn nnns 9 Computer Sense Terminals Summary heme senses sensn emen 9 COMPUTER CONTROL TRUTH
9. RWISE SPECIFIED CONCENTRICITY INSIDE CORNERS REMOVE BURRS BLOWBACK LINE POWER OPTION L NG 12 VDC OPTION EARTH DRY CONTACT NO COM NC TOLERANCE DECIMALS 2 PLACE 02 3PLACE 010 00511 R 031R MAX BREAK EDGES TO 005 MIN 020 MAX GROUND PROPRIETARY INFORMATION THIS DOCUMENT CONTAINS INFORMATION PROPRIETARY BALDWIN ENVIRONMENTAL AND IS TO BE USED SOLELY FOR THE PURPOSE FOR WHICH IT IS FURNISHED THIS DOCUMENT SHALL NOT BE USED FOR ENGINEERING DESIGN PROCURE MENT OR MANUFACTURING IN WHOLE OR IN PART BALDWIN ENVIRONMENTAL 2 1 DESCRIPTION TEM MODEL NUMBER 3300 DESCRIPTION Flow Control Drawer Back Panel DATE 8 4 99 DATE USED FOR BALDWIN ENVIRONMENTAL INC MATERIAL DESIGN DIMENSIONS ARE IN INCHES DENOTES MILLIMETER PART DESCRIPTION Flow Control Back Panel SIZE SCALE DRAWNG PART NO 3300REAR 1 Drawer EQUIVALENTS WHEN USED NSTR AIR 90 PSIG 40 F DEWPOINT Blowback Air Accumulator BALDWIN HEATED FILTER PROBE NOTES STANDARD MODEL 3300 HAS 2 GAS ANAYLZER CHANNELS AND 2 CALIBRATION GAS CHANNELS Stack To Manifold Plug Calib Gas 3 Way 3 Way EE Block Bleed Sample Direct ock Blee 2 System Cal Press Regulator set O 10 Psig Flow Meter 0 5 0 L MIN 2 Micron Sample Filter BALDWIN THERMO ELECTRIC COOLER Peristaltic Liquid Pu
10. m all personnel to prevent dangerous exposure e NEVER operate the equipment with any part of the enclosure unsecured All operated doors and covers must be in place and secured prior to operation Electrical current may be present behind covers or doors even if tools are not necessary to access these components e NEVER attempt service on this equipment without first disconnecting all energy sources Repair of this equipment should only be done by properly trained personnel that are familiar with the potential risks involved with servicing of the equipment e NEVER replace fuses with types other then the sample specification of type and current Do not bypass this or any other safety device e NEVER operate this equipment if it is visibly damaged or the possibility exists that it may have been damaged e The use of components that have not been purchased through an authorized Perma Pure dealer or directly from Perma Pure may compromise the safety of the operator Additionally use of non authorized components may change the operating characteristics of this equipment Any changes to the equipment that modify its operation in any way are dangerous and are strictly prohibited e Read the entire operating manual before attempting to set up or operate the equipment e Please heed all warning labels that are on the equipment They are there to remind you of possible hazardous conditions e Verify the integrity of any mechanical and or electrical con
11. mounted on a common manifold at the rear of the drawer and 2 the system direct solenoid valves located in the front of the drawer A block amp bleed solenoid valve which prevents the manifolds from being pressurized during sampling is also part of the system direct solenoid valve set The calibration function will only take place when both a calibration gas solenoid valve and either the system solenoid valve or direct solenoid valve have been selected In Local mode the calibration gas solenoid valves are cascaded that is if there are more than one 1 calibration gas solenoid valve switches in the on position only the highest numerical calibration gas solenoid valve will be active This is not the case with computer control The programmer can select any or all of the calibration gas solenoids Also computer control is not allowed in the Local mode While in the Local Direct Calibration mode manual blowback is allowed but not while in the Local System Calibration mode While under computer control blowback is allowed when nothing else is activated but not in any Calibration mode The Model 3300 has a provision for system bias checks System integrity is verified by comparison of calibration gas flow through the stack filter assembly to calibration gas flow directly to the gas analyzers This check indicates problems such as system leakage and gas component loss A probe filter blowback relay contact is provided on the Flow Control Drawer
12. mp BALDWIN SAMPLE CONDITIONING SYSTEM OPTIONAL VACCUM PRESSURE TRANSMITTER P1 P2 PUMP SAMPLE CALIB VACCUM PRESSURE SAMLE TRANSMITTER PRESSURE TOTAL FLOW 0 10 L MIN 2 WAY SOLENOID SYSTEM CALIBRATION nm V ERN 3 WAY SOLENOID SAMPLE DIRECT CALIBRATION 3 WAY SOLENOID GAS BLOCK amp BLEED OPTIONAL SAMPLE MANIFOLD CALIBRATION GASES NOTE Maximum of TRANSMITTER CG2 CG3 CG4 CG5 CG6 CG7 CG8 FLOW CONTROL DRAWER UNLESS OTHERWISE SPECIFIED PROPRIETARY INFORMATION THIS DOCUMENT CONTAINS INFORMATION PROPRIETARY BALDWIN INC AND IS TO BE USED SOLELY FOR THE PURPOSE FOR WHICH IT IS FURNISHED THIS DOCUMENT SHALL NOT BE USED FOR ENGINEERING DESIGN PROCURE MENT OR MANUFACTURING IN WHOLE FI 0 10 L MIN PK F2 0 2 5 L MIN PK F3 0 2 5 L MIN PK F4 0 2 5 L MIN PK F5 0 2 5 L MIN PK F6 0 2 5 L MIN PK F6 0 2 5 L MIN bkn 2 1 o oraw CALIB GAS TO PROBE RAW SAMPLE Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 or Bypass OPTIONAL CAL GAS PRESSURE DESCRIPTION TEM av USED MODEL NUMBER FOR pescription MODEL 3300 FLOW CONTROL DRAWER DRAWN BY DATE Mr 06 19 02 TN NISH PART DESCRIPTION MODEL 3300 SCALE DRAWING PART NO DESIGN DIMENSIONS 3300 FLOW ARE IN INCHES uo or s stus iow
13. n the Local LED is OFF the PC or PLC has control and can remotely duplicate local control functions The Local Switch provides an output to the PLC PC to indicate that the Flow Control Drawer is offline i e the analyzers outputs are not reliable CONTROL FUNCTIONS Switches Sample Blowback Direct System Calibration Calibration Local X X X Direct X System X Blowback X Cal Gas 1 8 X X Manual System Calibration To perform manual system calibration toggle the Direct System switch to the right Then toggle any of the Calibration Gas switches to the right This will allow the selected calibration gas to flow to the analyzer suite via the total sampling system In this mode manual blowback is not allowed Manual Direct Calibration To perform manual direct calibration toggle the Direct System switch to the left Then toggle any of the Calibration Gas switches to the right This will allow the selected calibration gas to flow to the analyzer suite directly bypassing the total sampling system In this mode manual blowback is allowed Manual Blowback To perform manual blowback depress the Blowback switch to the right This switch is a momentary switch that is it will return when released When the operator toggles the Blowback switch two things happen first the blowback relay will be activated and second the direct solenoid valve will be activated With the direct solenoid valve activated
14. nections that are made to the unit Verify that the unit is connected to the proper rated power for the system Verify that the unit is plumbed properly to operate effectively Model 3300 User s Manual PERMA PURE LLG Doc 532 Revision 000 HALMA Page 7 of 14 Operation A sample conditioning system supplies a clean dry sample to the back panel of the Model 3300 Flow Control Drawer The stack probe filter and sample pump performance are indicated by the Flow Control Drawer Vacuum Pressure Gauges Note Please refer to the attached Model 3300 Flow Diagram for an example of an integrated continuous emissions monitoring system flow schematic using the Model 3300 Flow Control Drawer Flow from the conditioning system enters the Model 3300 Flow Drawer sample calibration manifold Here either sample or calibration gas for direct calibration can be directed to the atmospheric pressure sample manifold and then on to the individual analyzer gas channels Individual sample flowmeters indicate the flow rate of each gas channel A bypass flowmeter vents excess sample gas not used by the continuous gas channels and also acts as an atmospheric vent The Model 3300 Flow Control Drawer has the ability to switch the sample and as many as eight 8 calibration gases to the analyzer rack directly or via the total sampling system This is done through two 2 sets of solenoid valves 1 the calibration gas solenoid valves which are
15. ng with the computer control mode of operation a computer verification method is also incorporated into the system A 40 pin vertical terminal block on the back panel allows the computer to verify the actions initiated by the computer This is done through a set of normally open dry contacts that are associated with each particular function Computer Sense Terminals Summary FUNCTION TERMINALS Cal Gas Valve 1 1 amp 2 Cal Gas Valve 2 3 amp 4 Cal Gas Valve 3 5 amp 6 Cal Gas Valve 4 7 amp 8 Cal Gas Valve 5 9 amp 10 Cal Gas Valve 6 1184 12 Cal Gas Valve 7 13 amp 14 Cal Gas Valve 8 15 amp 16 System Calibration 17 amp 18 Direct Calibration 19 amp 20 Blowback 31 amp 32 Local Mode 39 amp 40 Note The sense contacts are normally closed when activated except for blowback COPYRIGHT 2008 ALL RIGHTS RESERVED Original Instructions Model 3300 User s Manual b Doc 532 Revision 000 PERMA PURE LLCO Page 10 of 14 HALMA COMPUTER CONTROL TRUTH TABLE Terminal 2 4 T 31 Sy 7T 9 13t 13 15 6 FUNCTION System Calibration 1 System Calibration 2 System Calibration 3 System Calibration 4 System Calibration 5 System Calibration 6 System Calibration 7 System Calibration 8 UUUUUUUCUC Direct Calibration 1 Direct Calibration 2 Direct Calibration 3 Direct Calibration 4 Direct Calibration 5 Direct Calibration 6 Direct Calibration 7 Direct Calib
16. nsfers to the consignee Unpack your equipment Visually inspect the outside of your equipment for any damage If there is any damage contact the carrier immediately Generally a carrier must be notified within 24 hours of the delivery to make a hidden damage claim Items in the carton include 1 Model 3300 Flow Control Drawer 1 User s Manual If any of the above parts are missing or damaged call the helpline at 800 337 3762 ext 145 Introduction Thank you for purchasing this product from Perma Pure LLC This manual has been assembled so that it can answer all questions regarding operation Please keep the operators manual near the equipment for future reference There may also be optional equipment available that was not ordered at the time of original purchase which may be described and or illustrated in this manual If you still have any questions regarding your equipment s operation available options or technical support please contact your purchasing dealer or contact Perma Pure directly Perma Pure LLC Tel 732 244 0010 P O Box 2105 Tel 800 337 3762 toll free US 8 Executive Drive Fax 732 244 8140 Toms River NJ 08754 e mail info permapure com website www permapure com This equipment is to be installed and operated by trained personnel with sufficient command of the English language to clearly understand the instructions and safety warnings o COPYRI GHT 2008 ALL RIGHTS RESERVED Original Instructions
17. ration 8 X X X Blowback D Disabled Pressure Sensor Model 3300P The pressure sensor option provides e Vacuum pressure sensor 0 15 psig e Sample pressure sensor 0 30 psig e Calibration gas pressure sensor 0 30 psig Outputs 1 The standard output from all sensors is 4 20 mADC isolated loop powered 1 2 Outputs are terminated on the Flow Control Drawer back panel on the analog output Pressure Transducer Terminal Strip Connections 24 VDC Supply 4 to 20mA Output Vacuum Pin 1 Pin 2 Sample Pin 7 Pin 8 Calibration gas Pin 9 Pin 10 Sensor Calibration 1 All sensors are calibrated at the factory and should not be adjusted in the field without proper calibration pressure sources HALMA COMPAN PERMA PURE LLG Model 3300 User s Manual Doc 532 Revision 000 Page 11 of 14 Troubleshooting and Maintenance Guide Symptom Diagnostic Fix No LED display Not plugged in Power switch is off Fuse blown Power supply defect 12 VDC red black Check jumper JP1 Ribbon cable loose Defective control board Plug in instrument Turn on power Replace fuse Replace power supply Jumper 1 2 3 4 5 6 Tighten ribbon cables Replace control board Manual Control Local Switches have no effect Inadequate sample flow No system cal gas flow No direct cal gas flow Remote Local switch in remote Low sample p
18. ressure No cal gas from bottle Cal gas solenoid not operating Flow drawer regulator set lt 10psig Cal gas Flowmeter closed Block bleed solenoid constantly vents System cal gas solenoid valve defective Direct cal gas solenoid valve defective Select local Adjust sample pressure Cylinder to 15 psig Check cabling Replace cal gas solenoid Replace control board Set regulator to 10 psig Adjust Flowmeter Replace solenoid SV9 Replace solenoid SV10 Replace solenoid SV11 Check cables and connector boards for good connections Computer Control Remote Computer control has no effect No computer sense Remote Local switch in local Computer control wiring to terminal block is wrong Ribbon cable is loose Defective control board Computer sense wiring to terminal block is wrong Ribbon cable is loose Select remote Check cables Replace control board See computer control wiring section in manual Check cables COPYRIGHT 2008 ALL RIGHTS RESERVED Original Instructions Doc 532 Revision 000 HALMA CO Model 3300 User s Manual b PERMA PURE LLC Page 12 of 14 id Replacement parts 4D 3300 Part No Description 2FTS 021 Cal Gas connector 3DCB 006 Circuit board switch board FCD 2FIV 003 Flow meter 0 1 10 LPM w valve 2FIN 002 Flow meter 0 1 10 LPM no valve 2FIV 005 Flow meter 0 2 2 5 LPM w valve 1PSD 032 Power supply 100W 12VDC 2GAP 006 Pressure gauge 2 1 2 dia Face 2RP
19. s flow control system for monitoring and controlling of Total Extracted Sample Flow Individual Analyzer Sample Flow Bypass Flow Control Calibration Gas Pressure Regulation amp Flow Bias Check Sample Loss Due to Leaks or Gas Absorption Calibration Gas Leak Detection Stack Probe Blowback Tos IN Model 3300 User s Manual PERMA PURE LLG Doc 532 Revision 000 4 HALMA COMPANY Page 5 of 14 Physical description e Dimensions 5U 8 75 19 Rack Mount 18 depth e Weight 24 Ibs 10 9 kg Specifications Input cal gas channels maximum of 14 Sample 5 15 psig Vacuum 0 30 in Hg Calibration 5 35 psig Output gas channels 0 2 5 maximum of 6 Blowback Specify 12 VDC line voltage or dry contact Electrical requirements 90 240 VAC 50 60 Hz 100 watts Connections refer to Appendix A3 for back panel drawing 1 Sample Gas Connections are via 1 4 stainless steel bulkhead fittings 2 All Calibration Gases are 1 4 SS Tube Quick Connects 3 All Bulkhead Connections are labeled and follow the following functions Sample In SAMPLE Sample Vacuum Sense In VACUUM Calibration Gas Out to Stack Filter Assembly STACK Analyzer 1 CH1 Analyzer 2 CH2 Analyzer
20. to facilitate Manual or computer initiated blowback For Blowback there is a 250V 6Amp dry contact form C relay output provided on the back panel for blowback implementation There are two 2 vertical terminal block assemblies on the back panel provided for computer interface The 16 point terminal block is used for computer control and the 40 point terminal block is used for computer verification of flow control drawer operation Pressure Sensor Board Option Upstream stack filter and sample line the pressure drop is actively monitored by a vacuum transmitter the sample gas flow is verified by a sample manifold pressure transmitter and presence of adequate calibration gas is verified by a pressure transmitter on the calibration gas manifold COPYRI GHT 2008 ALL RIGHTS RESERVED Original Instructions Model 3300 User s Manual b Doc 532 Revision 000 PERMA PURE LLG Page 8 of 14 N HALMA Local Mode Operation To enter the Local mode toggle the Remote Local switch to the right While in the Local mode the operator can perform manual calibrations and blowback The flow control drawer is in Local Control when the Local Switch is selected the red LED is on and the green Sample LED is on as well In this mode all switches on the front panel are enabled for local operator control and Computer Control is disabled All Calibration Gas CG functions Direct System and blowback are available for the local operator Whe
21. which the product is put and Buyer shall conduct all testing and analysis necessary to validate the use and application to which Buyer puts the product for which Buyer may recommend the use or application of the product by others and 3 the characteristics specifications and or properties of the product may be affected by the processing treatment handling and or manufacturing of the product by Buyer or others and Seller takes no responsibility for he nature or consequence of such operations or as to the suitability of the product for the purposes intended to be used by Buyer or others after being subjected to such operations SELLER MAKES NO OTHER WARRANTY EXPRESS OR IMPLIED OF THE PRODUCT SUPPLIED HEREUNDER INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE AND ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED SELLER SHALL HAVE NO LIABILITY FOR LOSS OF PROFITS OR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES UNDER ANY CIRCUMSTANCES OR LEGAL THEORY WHETHER BASED ON NEGLIGENCE BREACH OF WARRANTY STRICT LIABILITY TORT CONTRACT OR OTHERWISE SELLER SHALL IN NO EVENT BE LIABLE IN RESPECT OF THIS ORDER AND OR PRODUCT DELIVERED ON ACCOUNT OF THIS ORDER FOR ANY AMOUNT GREATER THAN THAT PAID TO SELLER ON ACCOUNT OF THIS ORDER
Download Pdf Manuals
Related Search