Site Requirements_Spot
Contents
1. Phase 220Vac Zero 0 Main power inlet of the Spot e Circuit Breaker The printer electrical input should be protected by a 25A circuit breaker Remark Countries using 110Vac should use a transformer to convert the main power to 220Vac Using 2 phases of 110Vac instead of one phase of 220Vac will disable all safety components and could be dangerous For questions and comments you may contact our tech Support dept at support matanprinters com Matan Digital Printers Ltd 14 Amal St Rosh Ha ayin 48092 Israel Tel 972 3 9002720 Fax 972 3 9002721 Email support matanprinters com Website www matanprinters com Digital Printers e Power Connection the printer is supplied with a male power connector as shown in the picture below e The female connection supplied with the printer inside the tool box and shown below should be connected to the power box by an authorized technician Air Pressure Requirements The site should be equipped with an air compressor and air dryer as per the following specification Air preesure Dry air 5 5 10 Bar 87 1 74psi Air supply flow rate 50 Itr min 13 2 gllon min e The site should be equipped also with an air service unit Example of the air service unit and the connection diagram is detailed below miit ii H aai Air pressure 5 5 10 Bar Air pressure coming from compressor Air pressure to the Spot HNN NA i ii Nh wi ii printer Air t2. color 300m 984 feet e 1 rolls of media 50m 162 feet In addition each site must prepare an appropriate consumable stock of both ribbons and media Matan Digital Printers Ltd 14 Amal St Rosh Ha ayin 48092 Israel Tel 972 3 9002720 Fax 972 3 9002721 Email support matanprinters com Website www matanprinters com TAN Digital Printers Site Preparation End user statement Dear customer Thank you for reading Matan s Site Requirements for the Spot printer We would like you to fill in this document and email it or fax it to your local distributor and to Matan at support matanprinters com Fax 972 3 9002721 Please be aware that Matan s technical staff will not be able to arrive on site for installation amp training until this form is sent back to Matan for our approval Please note that the specifications are according to the user manual Have it on site and Site Requirements docs of the Spot printer Yes No Availability of a Forklift for unpacking the printer from its box Receiving area empty space of at least 10 sqm 108 sq ft for the printer and the installation according the spec Clean and leveled ground Static proof and dust proof floor The temperature amp humidity at the installation site are Temperature 21 28 C 68 83 F Humidity 50 70 not condensing Power output Electrical input amp Power connection on site should are 230 10V AC Single phase 24A Air pr
3. TAN Digital Printers Installation and Training Timetable We recommend that you allow sufficient time after the completion of the training process to allow your operator to get acquainted with the Spot prior to scheduling demonstrations or committing to production Installation and training are scheduled for three 3 working days and divided into three parts Basic installation and adjustment One working day This part will include unpacking site installation and various connections such as power and air as well as adjusting the printer Matan s service engineers will carry out this work Basic training One working day This part will include basic instruction in operation and in routine maintenance of the printer This part will be carried out together with the customer s Spot operator Practice One working day During this period the operators will train in the operation of the Spot under the supervision of Matan s Service engineers Site Preparation Environmental Requirements The delivery area e An empty receiving area of 10 sqm 108 sq ft is required in order to lift the printer from the delivery truck and rotate it for transporting to the site e Net printer dimensions width 164 cm 416 in length 153cm 388 in height 101cm 256 in weight 660k g e Gross printer Dimensions width 190cm 482 in length 190cm 482 in height 145cm 368 in weight 815kg The site area e You wil
4. apacity 5 000 BTU Hr min Liquid Outlet temperature 15 C 59 f e Liquid desired distilled water e Flow rate 5 10 GPM e Max Liquid Flow Rate Input 3bar 44pci e Chiller location Indoor 3 5M 10 16 feet from the Printer Connection requirements tubes e Inlet flexible tube Outside Diameter 8mm 0 3lin Inside Diameter 6mm 0 23in e Outlet flexible tube Outside Diameter 8mm 0 31lin Inside Diameter 6mm 0 23in e We recommend that you consult with your local chiller provider for the above requirements You may see more information at http Avww liquidchillers com Matan Digital Printers Ltd 14 Amal St Rosh Ha ayin 48092 Israel Tel 972 3 9002720 Fax 972 3 9002721 Email support matanprinters com Website www matanprinters com TAN Digital Printers PC Requerements The site should be equipped with a PC Laptop in order to control the printer as per the following min specification Window XP Pentium 4 3GHz H D 40G 7200rpm Support USB 2 0 RAM memory 512MB DDR CD drive Min x 52 Network card recommended Video card recommended Antivirus software recommended Site area ELECTRIC POWER Swirer ELECTRIC POWER INLET PNEUMATIC QUICK CONNECTOR CHILLER CONNECTION VACUUM PUMP GUTLET METRIC DIMENSIONS Figure 1 Spot Site Location Consumables Each printer is delivered with the following Starter Kit e 2 resin ribbons spot
5. essure on site Air Pressure Dry air 5 5 10 Bar 87 174psi Max 120 PSI 8 4 kg cm2 Air supply flow rate 50 Itr min 13 2 gallon min The site equipped with a vacuum cleaner with the spec above The site equipped with a Chiller according to the spec above know that the training is in the English Language Someone who speaks amp reads English fluently will be present during training amp installation Does the operator have experience with inkjet thermal printers Please specify which ones Does the operator have knowledge about RIP software Please specify which ones Does the operator have knowledge of any graphics amp design software Please specify which ones Please specify types brand amp model of substrates you will use on the Spot printer Media types O O O O OOOOO O Ee OU OL The site equipped with a PC Laptop with the above Min specification 0o Company name Full Name Full address Phone No Fax No Email Date f f Signature Matan Digital Printers Ltd 14 Amal St Rosh Ha ayin 48092 Israel Tel 972 3 9002720 Fax 972 3 9002721 Email support matanprinters com Website www matanprinters com
6. l need an electrical screwdriver with a Philips head recommended Ellen key 6 amp 4 in order to remove the printer from its box crate e The site should be equipped with a PC chiller vacuum cleaner amp a compressor these units are NOT provided with the printer details of which are to be found later in this chapter e The room must be free of dust dirt and powder of any kind Specifically metal or wooden scraps and pieces Please make sure that the printer is not placed near cutting machines of any sort grinding machines sawing machines or any dust Matan Digital Printers Ltd 14 Amal St Rosh Ha ayin 48092 Israel Tel 972 3 9002720 Fax 972 3 9002721 Email support matanprinters com Website www matanprinters com TAN Digital Printers making machines A dusty environment can cause damage to the print heads by creating scratches Matan will not be held responsible for damage to the printing heads as a result of a dusty environment Keep the box all the nuts bolts washers and spot washers for future transportation or for moving the printer Floor Requirements It is recommended that the floor should not be made of wood and should be covered with an anti static carpet Preliminary Site Preparation for the Spot Power Connection The site should be equipped with the following electrical requirements e Power Consumption 24A Max e Electrical Input 220 230 VAC 50 60 Hz Single phase r
7. ube length nit J li 5m max Air filter at least 20 ukm i _ Air service unit Matan Digital Printers Ltd 14 Amal St Rosh Ha ayin 48092 Israel Tel 972 3 9002720 Fax 972 3 9002721 Email support matanprinters com Website www matanprinters com TAN Digital Printers e The air must be clean dry and at the correct pressure It s recommended to install an air dryer between the compressor and the Spot printer in order to prevent water liquid from going into the pressure system e The air compressor and the air dryer should be connected to a separate phase from the printer e The humidity in the room should be between 50 to 70 e The room temperature must be between 21c to 28c 68 83F using air conditioning if needed Air service units are available from Matan at an additional cost See your local dealer for pricing amp delivery Vacuum Requirements The site should be equipped with a vacuum pump High flow with the following specification Vacuum level 48in Water 120 mbar Vacuum flow 46CFM 78m H Max power 1500W Temperature Control System TCS Requirements The site should be equipped with a chiller The Temperature Control System TCS liquid maintains the temperature of the Print Heads within a preset range of 2 C 35 f during the printing process Temperature Control System Below are the specifications for implementing a chiller Cooling c
Download Pdf Manuals
Related Search