Here - TopSpecUS.com
Contents
1. which 1 Extra Bright One 3 Volt Lithium battery type 2L76 or DL1 3N 50 000 h on setting 7 out of 10 ACET Diode Typically 500 000 h at NVD setting 130 mm 5 1 55 mm 2 2 55 mm 2 2 220 grams 7 8 oz 330 grams 11 6 oz including mount and spacer Range 2 m at 100 meters in windage and elevation 1 click 10 mm at 80 meters 13 mm at 100 meters 1 2 at 100 yards One wide ring 30 mm diam or Aimpoint QR Ring 45 C to 70 C 50 F to 160 F Submersible to 45 m 150 ft water depth MOA Minute Of Angle 1MOA 30 mm at 100 meters 1 at 100 yards NVD Night Vision Device 1 3 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS AND FUNCTIONS See fig 1 1 Battery Lid 2 Battery DL1 3N or similar 3 Cover for adjustment screw 4 Adjustment Screw windage 5 Adjustment Screw elevation 6 Lens Cover rear 7 Lens Cover front 8 Spacer 9 QRP2 Mount 10 Torque knob 11 Mounting Screw 12 Ring Mount 13 Rotary Switch CHAPTER II OPERATION UNDER NORMAL CONDITIONS Assembly and preparation for use WARNING Insure the weapon is unloaded and the safety selector is in the safe position before attempting to install remove or perform maintenance on the sight Installing Battery a Remove battery cap by turning it counter clockwise b Insert battery with positive end toward cap Caution while replacing battery not necessary when the sight is unused Before2. by firing at least three shots at a Zeroing target Check impact points on zeroing target to confirm accuracy and repeat above procedure if required f After initial firing ensure that the mount and sight are secure g Turn rotary switch to OFF position counter clockwise h Close front and rear lens covers CHAPTER IlI OPERATION UNDER EXTREME CONDITIONS a Extreme heat moist or dry No special procedures required b Extreme cold Extreme cold might shorten battery life c Salt air No special procedures required d Sea spray water mud and snow Ensure that battery cap and two adjustment screw caps are tight before exposing the sight to sea spray mud snow or before immersing the sight in water Hand tighten only Keep lens covers closed when sight is not being used Clean lenses with lens paper cloth and wipe the sight dry as soon as possible after exposure to water sea spray mud or snow e Dust storms and sand storms Keep lens caps closed when sight is not being used f High altitudes No special procedures required CAUTI ON The lenses shall never be cleaned with fingers but with lens paper cloth If no lens paper cloth available To clear away debris sand grass etc blow away the dirt To clean lenses mist up the lenses and dry them with a clean and soft piece of cloth CHAPTER IV TROUBLE SHOOTING PROCEDURES 4 1 Red dot does not appear Discharged battery Battery installed incorrectly Rep
3. installing battery cap inspect that the O ring is present and not damaged Failure to do so could result in water leakage into the battery compartment c Install battery cap by turning clockwise until snug Hand tighten only Using tools could damage equipment d Verify that red dot is present by turning the rotary switch clockwise Mounting Procedure a Select a groove on the rail that will give you a correct position of the sight Ensure that the groove is undamaged and clear of dirt and sand b Loosen the Torque Knob 10 by turning it counterclockwise c Install the mount and sight on the rail fig 1 Make sure that the mount is correctly positioned and that the Recoil Stop is in the selected groove d Push the mount forward fig 2 The Recoil Stop shall be in contact with the front edge of the groove e Tighten the Torque Knob fig 3 clockwise until it snaps twice This ensures that the Mount is secured NOTE Grasp the checkered portion of the knob only to prevent pinching of fingers when the shaft opens and snaps shut f Test shoot the weapon with the sight mounted Retighten the Torque Knob 10 after a few rounds if necessary g Perform complete zeroing according to 2 2 1
4. 2 2 OPERATING PROCEDURES 2 2 1 Zeroing Aimpoint s sights are delivered in a centered position Normally this means that only small adjustments are necessary providing that the base s are properly aligned CAUTION Do not continue to adjust windage and elevation mechanisms if you encounter resistance The elevation adjustment screw is located on top of the sight while the windage screw is located on the right side of the sight fig 3 a Open front and rear lens covers b Turn the rotary switch clockwise until the red dot has a sufficient intensity to contrast against the target c Remove the windage and elevation adjustment caps NOTE Each click of the adjustment screw corresponds to a 10 mm movement of the point of impact at 80 meters 3 mm at 25 meters 13 mm at 100 meters and 25 mm at 200 meters or 1 4 at 50 yds 1 2 at 100 yds and 1 at 200 yds d Insert adjustment tool coin screwdriver knife or cartridge casing in adjustment screw slot and turn as follows To move the point of impact to the right turn windage adjustment screw counter clockwise clockwise if screw located on left side To move the point of impact to the left turn windage adjustment screw clockwise counter clockwise if screw located on left side To move the point of impact up turn elevation adjustment screw counter clockwise To move the point of impact down turn elevation adjustment screw clockwise e Confirm zeroing
5. ications Aimpoint sights are designed for the two eyes open method of sighting which greatly enhances situational awareness and target acquisition speed Thanks to the parallax free design the dot follows the movement of the user s eye while remaining fixed on the target eliminating any need for centering Further the sight allows for unlimited eye relief The Patrol Rifle Optic is compatible with 1st 2nd and 3rd generation night vision devices The Patrol Rifle Optic sight is using Advanced Circuit Efficiency Technology ACET which combines Aimpoint s superior accuracy and ease of use with significantly lower power usage If you have further questions please contact your local dealer SPECIFICATION Material housing Material lens covers Surface finish Rubber cover Optical magnification Eye relief Optical coating Dot size Switch dot brightness Battery Battery life hours Length incl lens covers Width Height Weight sight only Weight with integrated mount Adjustment Mounting Max temperature range Water resistance Extruded high strength aluminum anodized Thermoplastic elastomer black non glare Hard Anodized Dark Graphite Grey matte Black or Dark Earth Brown 1X Unlimited no centering required Anti Reflex coating all surfaces Multi layer coating for reflection Band Pass coating for NVD compatibility 2 MOA 10 positions 4 NVD 6 daylight of
6. lace battery Remove and reinstall battery with toward cap Clean contact surfaces and reinstall battery Notify dealer armourer Battery is not making good contact Defective rotary switch 4 2 Impossible to zero Adjustment screw is at its limit Check alignment of mount to barrel Impact point is moving Check mount stability CHAPTER V MAINTENANCE a This reflex sight does not require any particular maintenance while used under normal conditions b Under severe weather conditions please refer to chapter III c Keep lens covers closed whenever the sight is not in use d Warehouse storage Remove battery and allow lens surfaces to dry completely if wet before closing the lens covers e To clean lenses refer to ca ution in chapter Ill FRY A A Ae N iy ROA wif Aimpoint User s manual for Aimpoint Patrol Rifle Optic Aimpoint AB J gershillgatan 15 SE 213 75 Malm Sweden Phone 46 0 40 671 50 20 Fax 46 0 40 21 92 38 e mail info aimpoint se www aimpoint com Aimpoint Inc 14103 Mariah Court Chantilly VA 20151 2113 USA Phone 1 703 263 9795 Fax 1 703 263 9463 e mail info aimpoint com www aimpoint com THE FUTURE IN SIGHT Copyright 2013 Contents property of Aimpoint All rights reserved 13648 0 CHAPTER PRESENTATION Aimpoint s Reflex Sights are rugged precision electronic optical red dot sights developed for civilian military and law enforcement appl
Download Pdf Manuals
Related Search