5300C-X Series - Dultmeier Sales
Contents
1. P HYPRO Series 5300C X 5321C 5322C and 5324C Small Twin Piston and Plunger Pumps Form L 0200P 6 11 Rev B Installation Operation Repair And Parts Manual Description SERIES 5300C X Cast Iron Small Twin Piston Pump Max Flow Rate 1 5 2 0 2 5 and 3 0 gom Max Pressure c 00008 500 psi Max Speed sse seeennnnnznnni 1725 rpm lo l A 1 2 NPT inlet 1 2 NPT outlet Max Operating Temp 1400 F SERIES 5321C amp 5322C Cast Iron Small Twin Plunger Pump Max Flow Rate 2 2 gpm Max Pressure 008 1000 psi Max Speed sssssseeemnnnnnnnni 1725 rpm POTS acnee ni 1 2 NPT inlet 1 2 NPT outlet Max Operating Temp 1800 F Safety Information SERIES 5324C Cast Iron Small Twin Piston Pump Max Flow Rate 2 9 gpm Max Pressure cc0000 800 psi Max Speed 00c000 1725 rpm ee ee ee nn 1 2 NPT inlet 1 2 NPT outlet Max Operating Temp 1400 F The following special attention notices are used to notifv and advise the user of this product of procedures that mav be dangerous to the user or result in damage to the product NOTE Notes are used to notifv of installation oper ation or maintenance information that is important but not safetv related CAUTION Caution is used to indicate the presence of a2. If opening around needle valve stem becomes clogged clean the valve stem and passage way with warm soapy water Rotate the control knob assembly counter clockwise which includes the control knob and needle valve stem until it can be lifted out of the body Inspect the valve stem o ring and replace if necessary Install the control knob assembly by pushing down firmly on the knob and turning clock wise until it is in the closed position Set the injector to the desired setting PARTS LIST Model No 3396 0014 3396 0006 Liquid Injector Heads Ref Quantity Part No Required Number Description 1 1 0257 5300C5 Cylinder Head for Model 3396 0014 cast iron 1 1 0254 5300C5 Cylinder Head for Model 3396 0006 cast iron 2 1 3400 0098 Unitized Valve Assembly 3 1 1720 0029 O ring 4 1 3200 0027 Body 5 1 3240 0006 Retainer Nut 6 1 1720 0033 O ring 7 1 3220 0016 Needle Valve Stem 8 1 2802 0002 Calibrated Adjustment Control Knob de Form L 0200P 6 11 Rev B NOTES Form L 0200P 6 11 Rev B ji NOTES 19 Form L 0200P 6 11 Rev B Limited Warranty on Hypro SHURflo Agricultural Pumps amp Accessories Hypro SHURflo hereafter Hypro agricultural products are warranted to be free of defects in material and workmanship under normal use for the time periods listed below with proof of purchase Pumps one 1 year from the date of manufacture or one 1 year of use This limited warranty will not exceed two 2 years i
3. 0006 Grease Fitting Assembly one No 1610 0011 Key two No 2230 0017 Set Screws Hollow Shaft Assembly No 5500 5321 Consists of one No 5501 5321 Crankshaft Sub Assembly two No 1810 0013 Retaining Rings two No 2008 0001 Main Bearings one No 2130 0007 Bearing Shield Ref Qty Part No Req d No Description 3430 0197 Set of four No 3400 0073 Unitized Valve Assemblies Consists of four each O ring Ref A Valve Seat Qty Part Req d No Description 2 2220 0012 Piston Cap Screw 2270 0011 Washer 2150 0047 Cup 1830 0092 1720 0029 1440 0059 Cup Holder O Ring Seal Ring 1440 0060 0500 5324 0608 5300 Guide Connecting Rod Safety Cover gt swali COIN OF W DY DOJM NH NIN PD 2210 0063 2210 0064 Cylinder Head Bolt 8 required for Hollow Shaft Pump 4 required for top cylinder head ONLY on Solid Shaft Pump Extra Long Cylinder Head Bolt for securing mounting base to Solid Shaft Pump 0201 5300C Cylinder Head Cast Iron 1720 0038 3430 0210 O Ring Ni Resist Cylinder Sleeve Assembly Consists of two each of No 1830 0033 Retainer Ref A No 1720 0079 O ring Ref B and No 3550 0028 Sleeve Ref C 15 Ref B Valve Poppet Ref C Valve Spring Ref D Valve Spring Retainer Ref E 0108 5300C Body Cast Iron 2405 0006 Grease Fitting 2230 0017 1610 0011 Hollow Shaft Sub Assembly see listing above Set Scre
4. 4 Using the Seat and Cage End Valve Extraction Tools remove the Unitized Valve Assembly from the Pump Body See Figures 9 and 10 Figure 11 Piston Sleeve Assembly Removal and Cleanup 5300X and 5324 only See Figures 12 amp 13 for Piston Stack Components Af Cap Screw Q Washer N N O ring N Cup Spreader N N Cup To remove Valve Cage Hook prongs of Valve Cage Extractor under three webs of the Valve Cage and pull up with a twisting motion Figure 9 N Cup Backing Plate O ring Seal Ring _ Guide To remove Valve Seat Hook Valve Seat Extractor under Seat and work out with an up and down motion Figure 12 BX Cap Screw N Washer Ne S Support Ring N Cup Holder W NL O ring Seal Ring wrench remove the Cap Screw from the Piston _ Guide Assembly for Models 5300X and 5324 For Models l 5321 amp 5322 remove the Plunger from the Pump Figure 13 Figure 10 5 Rotate the Pump Shaft so the Cam Bearing is in the upstroke position then using a 3 16 Allen Body after the Cap Screw is removed Form L 0200P 6 11 Rev B 1 Leave the pump body horizontal in the bench vise to remove the Cylinder Sleeves and Piston Assemblies Make sure the Cam Bearing is in the upstroke position Place one of the metal bars provided in the tool kit on the Cylinder Sleeve 2 Using a hammer gently tap the Cylinder Sleeve out of the Cylinder Head end of the pump body The Pis
5. 6 11 Rev B 11 Lubricate the O ring and install it on the Cup Spreader 12 Place the Cup Spreader end opposite O ring in the Cup inside the piston bore 13 Place the Washer on the Piston Cap Screw insert it through the Piston Assembly then tighten it to 130 in Ibs of torque 14 Turn the Pump over and repeat Steps 2 through 13 Plunger Assembly Installation Series 5321 and 5322 only NOTE Make sure the Cam Bearing is in the upstroke position when installing the Cylinder Sleeves and Piston Assemblies 1 Place the assembled Guide Retainer Cartridge and Plunger into the plunger bore of the Pump body making sure the Plunger and Connecting Rod seat together properly inside the Pump Body 2 Lubricate the O ring and place it on top of the Guide Retainer Cartridge 3 Place the Seal Retainer Cartridge over the Plunger beveled side down and press it by hand into the Pump Plunger bore 4 Place a Washer on the Plunger Cap Screw insert it through the Plunger and tighten it to 100 to 115 In Lbs of torque 5 Turn the Pump over and repeat Steps 1 through 4 Head and Grease Fitting Installation All Models 1 Install the O ring into the Pump Cylinder head 2 Place the Pump Body upright in a vise then place the Head on the Pump Body 3 Secure the head to the Pump Body with the Head Bolts then alternately and evenly in a criss cross pattern tighten the head Bolts 4 Turn the Pump over and repeat St
6. Inspection of Pump Parts When disassembling pump thoroughly inspect all parts and replace if necessary with special considera tion given to the following areas 1 Inspect Pump Body for erosion at O ring seal points in Valve and Piston bores Check for wear resulting from Main Bearings turning in Housing especially the Front Bearing area closest to the Cam Bearing Check for cracks in the Pump Body particularly at the discharge port and along the casting seam See Figure 7 2 Inspect for excessive wear on the Cylinder Heads This can result from erosion and or valve seat hammer See Figure 7 3 Inspect for pitting and general wear in the Unitized Valves particularly where the Poppets seal against the seat If this area is worn replace all four Valves See Figure 7 4 Inspect the Connecting Rod If there is more than 007 wear in the total space between the Connecting Rod and Cam Bearing the Connecting Rod should be replaced This can be determined using a feeler gauge The Cam Bearing should also be inspected as a bad cam bearing is the most common cause of a damaged Connecting Rod A worn Connecting Rod results in low volume low pressure a hammering sound and the pump running hot See Figure 8 Use a feeler gauge on this end to check amount of space Check this area for wear on both ends Figure 8 5 Inspect Crankshaft Assembly for general wear Rotate Cam Bearing and Main Bearings to check f
7. L 0200P 6 11 Rev B 7X Metal Valve Seat Points up C Figure 21 Cylinder Sleeve and Piston Stack Installation Series 5300X and 5324 only NOTE Clean the cylinder sleeves using the Burnishing Adapter provided with the tool kit The Burnishing Adapter is to be mounted on an elec tric motor shaft 1 Insert the Cylinder Sleeve Brass Retainer End out into the Burnishing Adapter and polish the inside surface using a No 320 grit emery cloth 2 Use a wire brush to clean the outside of the Cylinder Sleeve NOTE Upon inspection if pitting or scratches still show on the inside of the Cylinder Sleeve the Cylinder Sleeve and the Cylinder Sleeve O ring should be replaced 3 Insert the Cylinder Sleeve into the cylinder bore of the Pump Body 4 Lubricate and place a new Cylinder Sleeve O ring on top of the Cylinder Sleeve 5 Place a Brass Retainer on top of the O ring 6 Insert the Guide into the Cylinder Sleeve making sure the Guide is properly seated on the Connecting Rod inside the Pump Body 7 Place the Seal Ring at a 45 degree angle on top of the Guide then using the Seal Ring Seating Tool press the Seal Ring into the Cylinder sleeve 8 Lubricate the O ring and place it on the Cup Backing Plate 9 Install the Cup Backing Plate on top of the Seal Ring in the piston bore O ring end down 10 Lubricate the Cup and set it on top of the Cup Backing Plate inside the piston bore Form L 0200P
8. Seal Retainer Form L 0200P 6 11 Rev B Clean up of the Pump Body and Heads All Models 1 Using the port wire brush with an air gun or electric hand drill clean the outlet port and inlet port plus the valve and piston bores in the Pump Bodv 2 Use a hand file or belt sander to clean corrosion and rust from the top and bottom of the Pump Bodv and the bottoms of the cvlinder Heads 3 After performing Steps 1 and 2 Hvpro recom mends that the pump Body and Cylinder Head be further cleaned in a solvent tank to remove any remaining rust and corrosion particles NOTE If the solvent cleaning is not performed the valve and piston bores must be wiped as clean as possible Crankshaft and Main Bearing Disassembly Reassembly All Models Disassembly 1 To remove the Front Main Bearing from the Crankshaft position a pipe support fixture on the arbor press then place two metal bars parallel to each other one on each side of the fixture See Figure 17 2 Place the Crankshaft Assembly in the fixture drive end up with the metal bars between the Bearing and fixture to support the Outer Bearing See Figure 17 NOTE Make sure the metal bars do not touch the Retaining Ring on the Crankshaft 3 Using the arbor press press the Crankshaft through the Bearing See Figure 17 WARNING Special attention should be exercised when working with retaining rings Always wear safety goggles when working with spring or ten
9. hazard which will or can cause minor injury or property damage if the notice is ignored WARNING Warning denotes that a potential hazard exists and indicates procedures that must be fol lowed exactly to either eliminate or reduce the haz ard and to avoid serious personal injury or prevent future safety problems with the product DANGER Danger is used to indicate the presence of a hazard that will result in severe personal injury death or property damage if the notice is ignored DANGER DO NOT pump flammable or explosive fluids such as gasoline fuel oil kerosene etc DO NOT use in explosive atmospheres The pump should be used only with liquids compatible with the pump component materials Failure to follow this warning can result in personal injury and or proper ty damage and will void the product warranty A pressure relief device such as an unloader relief valve or balancing regulator must be installed on the outlet side of the pump Failure to do so could result in personal injury and or void the warranty e Be sure all exposed moving parts such as shafts couplers and adapters are properly shielded or guarded and that all coupling devices are securely attached before applying power e Hollow shaft pumps mounted directly onto power shaft must be prevented from rotating with the power shaft by means of a device such as a torque arm Pump must float freely on the power shaft and must not be tied rigidly to equipment o
10. horsepower required to operate pump For gas engine drive select couplings rated at three times the required pump horsepower Form L 0200P 6 11 Rev B 2 CAUTION For safety always install a shield over rotating shafts and couplings Figure 3 Direct Drive Hollow Shaft Installation Hollow shaft models mount directly on the motor or engine shaft See Figure 4 Adapters are available to convert some solid shaft models for direct shaft mount ing After mounting the pump always turn it by hand to make sure the pump is operating freely Never apply power to a pump that appears to be stuck CAUTION Use a torque arm to keep the pump from rotating with the shaft The pump must be allowed to float on the shaft and must not be tied rigidly to the equipment on which it is mounted CAUTION For safety always install a shield over rotating shafts Or enclose the pump motor assembly inside a housing System Installation Inlet Pressure Regulator Line Strainer Compound Gauge Pulsation Dampener Filled Pressure MI ee ZL Nozzle Spray Gun Bypass Back to Inlet Figure 5 Piston Pump Installation Accessories should be installed with solid piping and be mounted as close to the pump as possible The hose must be used right after accessories NOTE If remaining installation is solid piping a two to four foot length of hose must be installed between accessories and so
11. min Pressure at Pump Outlet 3 45 MPa 3 45 MPa 6 9 MPa 5 52 MPa Pump Inlet Conditions 127 mm Hg 68 9 kPa 137 8 kPa 127 mm Hg 68 9 kPa 137 8 kPaj127 mm Hg 68 9 kPa 137 8 kPaj127 mm Hg 68 9 kPa 137 8 kPa iti Tala 266 4 ml 177 6 ml 148ml 266 4ml 177 6 mi 148ml 266 4ml 177 6 mi 148ml 266 4 mi 177 6 mi 148 mI Form L 0200P 6 11 Rev B i DIMENSIONS X 3 13 16 Y 5 5 16 X 96 8 mm Y 135 mm X 3 3 16 Y 5 11 16 X 106 4 mm Y 144 5 mm INSTALLATION IMPORTANT Liquid injector cylinder head MUST be installed with the flow regulator Flow l Regulator channel over the inlet valve of the Channel 7 pump Inlet Side is cast on the cvlinder head of injector for ease in O ring identification Groove TO ADJUST THE POSITION OF THE INLET PORT To change the position of the liquid injector inlet port loosen the retainer nut Ref 5 and rotate injector body Ref 4 until the opening is in the desired position It is important that the retainer nut be fully tightened to properly compress the o ring seal Ref 3 against the valve assembly Ref 2 OPERATION Before using the injector make sure the retainer nut is tightened securely NOTE The Inlet Port on the body indicates the position of the dial setting closed position is zero The larger the number the more flow is allowed DO NOT rotate the control Knob more than three complete turns MAINTENANCE
12. small knife blade remove the O ring Seal Ring combination from the Guide Retainer 3 Using a small knife blade remove the Brass Support Ring and Support Ring Seal combination from the Seal Retainer 4 Inspect and clean the Brass Guide and Seal Retainers Clean them with a wire brush and check them for burrs and nicks Use 320 grit emery cloth to remove burrs To Reassemble the Plunger Cartridges 1 Lightly lubricate the O ring and place it around the Seal Ring 2 Position the O ring Seal Ring combination in the Guide Retainer at a 45 degree angle 3 Using the Guide seat the O ring Seal Ring Combination into the Guide Retainer leaving the Guide in the Guide Retainer 4 Place the Guide Retainer on a flat surface so that the exposed portion of the Guide is down 5 Place the cap screw end of the Plunger into the Guide Retainer and press it through until the Plunger is flush with the bottom of the Guide Retainer 6 Turn the Cartridge over and push the Guide Retainer down the Plunger until it is flush with the bottom of the Plunger Seal Retainer Cartridge 1 Place the beveled side of the Inner Support Ring in the grooved side of the Seal then place the Seal Retainer over the Support Ring side of the Support Ring Seal combination 2 Press the above items in with your fingers until the Support Ring Seal combination bottoms out inside the Seal Retainer 3 Place the Brass Support Ring on the open side of the
13. 5112 For technical or application assistance call the Hypro Technical Application number 800 445 8360 or send an email to technical hypropumps com To obtain service or warranty assistance call the Hypro Service and Warranty number 800 468 3428 or send a fax to the Hypro Service and Warranty FAX 651 766 6618 Carriers including U S P S airlines UPS ground freight etc require specific identification of any hazardous material being shipped Failure to do so may result in a substantial fine and or prison term Check with your shipping company for specific instructions gt gt Pentair SPRAY amp INJECTION TECHNOLOGIES GROUP 375 Fifth Avenue NW 7 New Brighton MIN 55112 Printed in the USA Phone 651 766 6300 7 800 424 9776 7 Fax 800 323 6496 2011 Hypro www hypropumps com
14. 5C H 5501 5330 5500 5330 5330C H with 5 8 Solid Shaft Ref 15 5001 5315 5000 5315 5315C 5001 5320 5000 5320 5320C 5001 5325 5000 5325 5325C 5001 5330 5000 5330 5330C Description 3430 0197 Set of four No 3400 0073 Unitized Valve Assemblies Consists of four each O ring Ref A Valve Seat Ref B Valve Poppet Ref C Valve Spring Ref D Valve Spring Retainer Ref E 0108 5300C Body Cast Iron 2130 0007 Bearing Shield 2008 0001 Main Bearing Ball Bearing 1810 0013 Bearing Retainer Ring shaft 1820 0025 Bearing Retainer Ring housing 1510 0056 Mounting Base 2820 0040 Torque Arm for Electric Motor Mounting 2220 0039 2270 0042 1830 0056 2150 0027 1830 0054 1720 0079 Models 5321C and 5322C Socket Head Cap Screw Washer Retainer Seal Assembly Consists of No 2150 0049 Seal Ref A and No 1440 0061 Support Ring Ref B Seal Retainer O ring for Seal Retainer 1440 0037 1720 0064 1440 0010 Guide O ring for Seal Ring Seal Ring 1830 0053 3500 0021 3500 0036 Guide Retainer Plunger steel Model 5321 Plunger ceramic Model 5322 2 2 2 2 2 2 2 2 1 1 1 0502 5300 0504 5300 0608 5300 Connecting Rod Model 5321 Connecting Rod Model 5322 Safety Cover 2210 0063 2210 0064 Cylinder Head Bolt 8 bolts required for Model 5321C H Hollow Shaft Pump 4 bolts required for Top Cylinder Head ONLY on Solid Shaft Pumps Extra
15. Assembly one No 1610 0011 Key and two No 2230 0017 Set Screws Hollow Shaft Assembly No 5500 5321 Consists of one No 5501 5321 Crankshaft Sub Assembly two No 1810 0013 Retaining Rings two No 2008 0001 Main Bearings and one No 2130 0007 Bearing Shield Valve Assemblies Consists of four each O ring Ref A Valve Seat Ref B Valve Poppet Ref C Valve Spring Ref D and Valve Spring Retainer Ref E 0108 5300C Body Cast Iron 2405 0006 Grease Fitting Hollow Shaft Sub Assembly see listing above 2230 0017 1610 0011 Set Screws for Hollow Shaft Spline Key for Hollow Shaft Solid Shaft Sub Assembly see listing above 1610 0007 2130 0007 2008 0001 1810 0013 1820 0025 1510 0041 3420 0030 Spline Key for Solid Shaft Shield Main Bearing Retaining Ring shaft Retaining Ring housing Mounting Base for Solid Shaft Models Torque Arm Kit for Hollow Shaft Models Consists of No 2820 0035 Torque Arm No 1450 0003 Bumper and two No 2210 0064 Bolts 2270 0097 Washer Model 5322 only Form L 0200P 6 11 Rev B Spec Pumps 53702 and 53703 Crankshaft Assemblies 4 5 TA a e Spec Pump No 53702 6 KI Hollow Shaft Sub Assembiv No 5501 5318 7 SS Consists of one No 0550 5318 Crankshaft one No 3 Cc gt 2007 0029 Cam Bearing one No 2405 0006 9 3 Grease Fitting Assembiv one No 1610 0011 Kev 10 two No 2230 0017 Set Screws ee ES Hollow Shaft Assembl
16. DA approval is required use one of these greases Chevron FM 2 Mobile FM 2 Keystone Penwalt Corp Nevastane SP Medium Lubricate every 50 hours or monthly With a screwdriver or flat tool apply a generous dab of grease to outer diameter surface of cam bearing at top and bottom where bearing contacts connecting rod Do not grease excessively Check periodically and scrape out do not WASH out any excess grease from pump cavity Repair Instructions Recommended Repair Tools For Hypro Small Twin Piston Plunger Pumps Used for Series Ref Part No Description 5321 5324 5300 A 1055 0005 Seal Ring Seating Tool B 3010 0052 Valve Cage Extractor C 3010 0061 Main Bearing Support Tool D 3010 0063 Cam Bearing Support Tool E 3010 0064 Support Bars Qnty 2 F 3010 0065 Prv Bar G 3010 0066 Wire Brush H 3010 0067 Wire Brush Holder 3010 0071 Valve Seat Extractor J 3010 0222 Seal Ring Seating Tool K 3020 0001 3 16 Allen Wrench L 3020 0003 1 8 Allen Wrench M 3020 0009 1 16 Allen Wrench Recommended Shop Tools Bench Press Arbor Press Air Gun or Electric Hand Drill Metal Pipe Support Fixture 3 diameter x 4 1 2 high Ratchet Handle Wrench with 9 16 Hex Socket Bolt 3 8 diameter x 4 1 2 long No 320 Grit Emory Cloth Pliers Small Knife Large File Claw Hammer Standard Screwdriver Lubricating Spray WD 40 or LPS Wire Brush hand or machine Stationary Belt Sander and Cleaning Solvent Tank recommended
17. Head Ni Resist Cylinder Sleeve Assembly Consists of two each of No 1830 0033 Retainer Ref A No 1720 0079 O ring Ref V and No 3550 0018 Sleeve Ref C Form L 0200P 6 11 Rev B 12 Piston Stack Parts Kit Leather Cup Kit No 3430 0007 Consists of two each of the following parts No 2220 0012 Piston Cap Screw Ref 6A No 2270 0011 Washer Ref 6B No 1720 0029 O ring Ref 6C No 2150 0002 Leather Cup Ref 6D No 1720 0039 O Ring Ref 6E and No 1440 0008 Seal Ring Ref 6F Rubber Cup Kit No 3430 0009 Same as above kit except with No 2150 0005 Rubber Cups Piston Stack and Guide Parts Kits Leather Cup and Guide Kit No 3430 0008 Consists of Leather Cup Kit No 3430 0007 plus two No 1440 0004 Piston Guides Ref 7 Rubber Cup and Guide Kit No 3430 0010 Consists of Rubber Cup Kit No 3430 0009 plus two No 1440 0004 Piston Guides Teflon Cup and Guide Kit No 3430 0046 Consists of Teflon Cup Stack Kit plus 2 Piston Guides Crankshaft Assemblies Sub Assemblies include Shaft Ref 12 or 15 with Cam Bearing Grease Fitting Assembly Ref 10 Set Screws for Hollow Shaft Ref 13 and Spline Key Ref 14 or 16 Complete Assemblies include the Sub Assembly plus parts identified by Reference Numbers 24 26 Sub Assembly Complete Assembly Pump Part No Part No Model with 5 8 I D Hollow Shaft Ref 12 5501 5315 5500 5315 5315C H 5501 5320 5500 5320 5320C H 5501 5325 5500 5325 532
18. Long Cylinder Head Bolt for securing mounting base to Solid Shaft Models 0201 5300 1720 0038 Cylinder Head Cast Iron O ring for Cylinder Head 13 Plunger Parts Kits Plunger Stack Parts Kit No 3430 0144 Model 5321 Consists of two each of the following parts No 1440 0010 Seal Rings No 1440 0037 Guides No 1720 0064 O rings No 1720 0079 O rings No 2150 0027 Seal Assemblies No 2220 0039 Socket Head Cap Screws and No 2270 0042 Washers Plunger Parts Kit No 3430 0145 Model 5321 Consists of one No 3430 0144 Plunger Stack Parts Kit and two No 3500 0021 Plungers Plunger Stack Parts Kit No 3430 0291 Model 5322 Consists of two each of the following parts No 1440 0010 Seal Rings No 1440 0037 Guides No 1720 0064 O rings No 1720 0079 O rings No 2150 0027 Seal Assemblies No 2220 0039 Socket Head Cap Screws and No 2270 0042 Washers Plunger Parts Kit No 3430 0292 Model 5322 Consists of one No 3430 0291 Plunger Stack Parts Kit and two No 3500 0036 Plungers Crankshaft Assemblies Solid Shaft Sub Assembly No 5001 5321 Consists of one each of the following parts No 0500 5321 Crankshaft No 1600 0014 Crankpin Retainer No 2007 0029 Cam Bearing No 2405 0006 Grease Fitting Assembly and No 1610 0007 Key Hollow Shaft Sub Assembly No 5501 5321 Consists of one No 0550 5321 Crankshaft one No 2007 0029 Cam Bearing one No 2405 0006 Grease Fitting
19. constant speed dynamometer tests pumping water at one foot approx suction lift with no pulsation damper Performance will vary with application Series 5321C and 5322C J 7BAR 20BAR 40BAR 50BAR OOBAR PAPRJLIMIN L w JUmin w Lmin w fimin w Lmin w 900 42 165 42 261 42 1399 a2 faer 41 1575 1200 6 8 224 56 357 55 596 55 e03 54 730 aso 69 269 68 ao 67 601167 17001 66 e86 Form L 0200P 6 11 Rev B 11 Models 5315C X 5320C X 5325C X and 5330C X NOTE When ordering parts give QUANTITY PART NUM BER DESCRIPTION and COM PLETE MODEL NUMBER Reference numbers are used ONLY to identify parts in the drawing and are NOT to be used as order numbers 2220 0012 2270 0011 1830 0017 Piston Cap Screw Washer Piston Cup Spreader 1410 0030 1440 0004 Cup Backing Plate Piston Stack Parts Kit see listinabove Piston Guide 0502 5300 0608 5300 2405 0006 Connecting Rod Safety Cover Grease Fitting Assembly elea aN ea NINNN N 2230 0017 1610 0011 Crankshaft Assemblies Hollow Shaft Models see listing above Set Screw for Hollow Shaft Spline Key for Hollow Shaft 1610 0007 2210 0062 Crankshaft Assemblies Solid Shaft Models see listing above Spline Kev for Solid Shaft Cvlinder Head Bolt 0204 5300C j Cylinder Head Cast Iron 1720 0038 3430 0209 O ring for Cvlinder
20. e bolt push the Crankshaft Assembly out of the Pump Body See Figure 14 Plunger Cartridge Removal Disassembly Reassembly Series 5321 and 5322 only See Figure 15 for Plunger Cartridge Components DLA Cap Screw Support Ring Brass D Inner Support Ring O ring N n O ring ao Seal Seal Ring A NU Seal Retainer Brass Sj NL Guide Guide Retainer Brass Plunger Steel 5321 Ceramic 5322 Washer 5322 ONLY Figure 15 To Remove the Plunger Cartridges from the Pump Body 1 Position the pump upright on the arbor press with the Safety Cover opening facing out Place the Plunger Cartridge Extractor Tool machined side down on the Guide Retainer inside the pump body Place the bolt threaded end down through the Plunger Bore on the other end of the pump until it rests in the counter sink hole on the Cartridge Extractor Tool Place the arbor press ram on the bolt head and push both the Seal and Guide Retainer out of the pump body See Figure 16 Turn the pump over and repeat Steps 1 through 4 Form L 0200P 6 11 Rev B To Disassemble the Guide and Seal Cartridges 1 Remove the Guide from the Guide Retainer by pulling it out with one finger NOTE If the guide does not come out in this man ner use a screwdriver and a hammer to gently break off a section of the Guide being careful not to damage the Guide Retainer The remaining por tion of the Guide will then fall out 2 With a
21. e of reading double the pump working pres sure Use a silicone filled gauge or a gauge dampener to pro tect the gauge needle against pressure surges and provide easier reading Operation Priming If the liquid is below level of the pump some means should be provided in installation to prime pump such as a foot valve or check valve to hold prime Keep suc tion lift to minimum and avoid unnecessary bends in the suction line Before starting pump make sure air bleed er valve or spray gun is open or unloader valve is adjusted to its lowest pressure After starting pump open and close gun several times if necessary to aid priming the pump If pump does not prime within a few seconds stop motor and inspect installation for suction line leaks or obstructions Make sure that strainer is not clogged Be sure that suction line is not obstructed kinked or blocked lf the pump is to operate hours at a time check fre quently for 1 Adequate liquid supply Pump must not run dry for more than 30 seconds 2 Temperature rise Overheating is harmful to bear ings and piston cups NOTE Models 53702 and 53703 Inlet Requirements Pressure feed 20 to 100 psi Care of Pump Your pump will last longer and give best performance when properly taken care of Proper pump care depends on the liquid being pumped and when pump will be used again In a normal car wash or detergent cleaning installation where each application is followed by a cl
22. ear water rinse the pump will be kept clean After each use flush pump with a neutralizing solution for the liquid just pumped Follow with a clear water rinse This is especially important for corrosive chemi cals Then flush out pump with a 50 solution of auto motive ethylene glycol type radiator antifreeze contain ing a rust inhibitor Form L 0200P 6 11 Rev B While this flushing is not absolutely necessary for short periods of idleness as overnight it is good practice to clean the pump after each use to prevent deposits from forming and damaging the pump The antifreeze not only coats the interior of the pump with an inhibitor but acts as a lubricant as well keeping valves from sticking and protecting against any remaining moisture freez ing in cold weather For infrequent use and before long periods of storage drain pump thoroughly Open any drain plugs remove suction hose from liquid and run pump dry from O to 30 seconds not longer Once again a rust inhibitor should be injected into the pump before both ports are plugged and the pump is stored Then plug both ports to keep out air until pump is used again Lubrication Schedule Use a grease gun to lubricate Hypro Series 5300 and 5324 Piston Pumps and Series 5321 and 5322 Plunger Pumps DO NOT USE AIR POWERED GREASE GUNS as they develop too much pressure and may cause damage to the sealed cam bearing Lubrication EXCEPTION In applications where F
23. eat Ref B Valve Poppet 2150 0049 Seal Ref A and one Ref C Valve Spring Ref D Valve No 1440 0061 Support Ring Ref B Spring Retainer Ref E 0108 5300C Body Cast Iron 2405 0006 Grease Fitting i Hollow Shaft Sub Assembly See listing above for description 2230 0017 Set Screws for Hollow Shaft 1610 0011 Spline Key for Hollow Shaft 2130 0007 Shield 2008 0001 Main Bearing 1810 0013 Retaining Ring shaft 1820 0025 Retaining Ring housing 3420 0030 Torque Arm Kit Includes 1 No 2820 0035 Torque Arm 1 No 1450 0003 Bumper and 2 No 2210 0064 Bolts 2270 0097 Washer Form L 0200P 6 11 Rev B f Models 5324C and 5324C H Piston Parts Kit Piston Stack Parts Kit No 3430 0191 Consists of two each of the following parts No 2220 0012 Cap Screw Ref 2 No 2270 0011 Washer Ref 3 No 2150 0047 Cup Ref 4 No 1720 0029 O ring Ref 6 No 1440 0059 Seal Ring Ref 7 and No 1440 0060 Guide Ref 8 Crankshaft Assembly Kits Model 5324C Solid Shaft Sub Assembly No 5001 5321 Consists of one each of the following parts No 0500 5321 Crankshaft No 1600 0014 Crankpin Retainer No 2007 0029 Cam Bearing No 2405 0006 Grease Fitting Assembly No 1610 0007 Key Model 5324C H Hollow Shaft Sub Assembly No 5501 5321 Consists of one No 0550 5321 Crankshaft one No 1600 0014 Crankpin Retainer one No 2007 0029 Cam Bearing one No 2405
24. eps 1 through 3 5 To install the Grease Fitting into the Cam Bearing place the pump on the arbor press with the Safety Cover side facing up then press the Grease Fitting in with the arbor press ram 6 Grease the pump according to the Lubrication Instructions 7 Install the safety cover 10 Troubleshooting Symptom Probable Cause s Corrective Action s No Flow or Low Flow Pump not primed Refer to Priming in the Operation Section Air leaks in suction line Check and reseal inlet fittings Blocked or clogged line strainer Inspect strainer and clear any debris from screen Undersize suction line or collapsed hose Suction line should be the same diameter as inlet port of Pump or larger Nozzle clogged Clear nozzle or replace Low pressure Debris in Valves Remove debris See Repair section Valves worn Replace Valves See Repair section Repair or replace relief valve TITU e mm Performance Data Unloader or Relief Valve not functioning properly Repair or replace Relief Valve Series 53702 Presssurej 100 psi 300 psi 500 psi 700 psi f 1000 psi RPM JGPMHPJGPM HPJGPM HPJGPM HPJGPM HP Series 53703 Presssure 100 psi 300 psi 500 psi 700 psi 1000 psi 689 4 KPa 2000 KPa 4000 KPAJSO0D KPal 6804 KPa GPM HP GPM HPJGPM HP 8 3 491 8 0 756 7 9 888 689 4 KPa 2000 KPag4000 KPag5000 KPaj 6894 KPa 8 5 298 8 3 491 f 7 9 756 f 7 7 888 7 4 1118 NOTE Above performance figures based on
25. eviation from this document Return Procedures All products must be flushed of any chemical ref OSHA section 1910 1200 d e f g h and hazardous chemicals must be labeled tagged before being shipped to Hypro for service or warranty consideration Hypro reserves the right to request a Material Safety Data Sheet from the returnee for any pump product it deems necessary Hypro reserves the right to disposition as scrap products returned which contain unknown fluids Hypro reserves the right to charge the returnee for any and all costs incurred for chemical testing and proper disposal of components containing unknown fluids Hypro requests this in order to protect the environ ment and personnel from the hazards of handling unknown fluids Be prepared to give Hypro full details of the problem including the model number date of purchase and from whom you purchased your product Hypro may request additional information and may require a sketch to illustrate the problem Contact Hypro Service Department at 800 468 3428 to receive a Return Merchandise Authorization number RMA Returns are to be shipped with the RMA number clearly marked on the outside of the package Hypro shall not be liable for freight damage incurred during shipping Please package all returns carefully All products returned for warranty work should be sent shipping charges prepaid to HYPRO Attention Service Department 375 Fifth Avenue NW New Brighton MN 5
26. lid piping Hose Selection of the right size and type of hose is vital for good performance Be sure to hook up to the proper ports on the pump note markings IN and OUT on pump castings Suction Hose Always use genuine suction hose compatible with the fluids being pumped and at least the same inside diameter as pump ports If the suction hose is over 5 feet long use the next larger size hose Keep the suction hose as short as possible and restrictions such as elbows check valves etc at a minimum Discharge Hose High pressure pumps require the use of special high pres sure discharge hose 2 rayon braid or equivalent Use a hose rated at least 50 greater than the highest operating pressure required of pump Example If required pump pres sure is 200 psi use discharge hose rated at minimum of 300 psi working pressure Unloader Valve The unloader has a very important safety function in your piston pump hookup The unloader valve protects the pump by unloading pressure when the gun is shut off or discharge is otherwise blocked This saves the pump and power because the liquid is bypassed at a very low pressure If the gun is to be shut off for more than 5 minutes install a pump protector in the inlet side or stop the pump to prevent heat buildup The length of time may vary due to the original tem perature of the fluid being pumped Strainers Use a suction line strainer with at least 3 to 5 times the suc
27. n any event Accessories ninety 90 days of use This limited warranty will not apply to products that were improperly installed misapplied damaged altered or incompatible with fluids or components not manufactured by Hypro All warranty considerations are governed by Hypro s written return policy Hypro s obligation under this limited warranty policy is limited to the repair or replacement of the product All returns will be tested per Hypro s factory criteria Products found not defective under the terms of this limited warranty are subject to charges paid by the returnee for the testing and packaging of tested good non warranty returns No credit or labor allowances will be given for products returned as defective Warranty replacement will be shipped on a freight allowed basis Hypro reserves the right to choose the method of transportation This limited warranty is in lieu of all other warranties expressed or implied and no other person is authorized to give any other warranty or assume obligation or liability on Hypro s behalf Hypro shall not be liable for any labor damage or other expense nor shall Hypro be liable for any indirect incidental or consequential damages of any kind incurred by the reason of the use or sale of any defective product This limited warranty covers agricultural products distributed within the United States of America Other world market areas should consult with the actual distributor for any d
28. n which it is mounted e Do not exceed recommended speed pressure and temperature for pump and equipment being used e Before servicing disconnect all power make sure all pressure in the system is relieved drain all liquids from the system and flush e Secure the discharge lines before starting the pump An unsecured line may whip causing personal injury and or property damage e Check hose for weak or worn condition before each use Make certain that all connections are tight and secure Periodically inspect the pump and the system com ponents Perform routine maintenance as required see Maintenance section Protect pump from freezing conditions by draining liquid and pumping rust inhibiting solution such as antifreeze through the system coating the pump interior Use only pipe hose and fittings rated for the maxi mum or greater PSI rating of the pump Do not use these pumps for pumping water or other liquids for human or animal consumption Drive Source Installation This manual will cover the installation of the basic drive configurations available for the Hypro Small Twin Piston and Plunger pumps Consult the manufacturer of your motor or engine for additional information Read all instructions and general safety information before attempting to install or operate the pump Belt Pulley Drive Installation Mounting Belts and Pulleys Mount pulleys as close to pump and motor engine shaft bearings as po
29. or roughness due to moisture contamination or lack of grease If main bearings do not turn smoothly or appear to be damaged they should be replaced If cam bearing is damaged a new Crankshaft Sub assembly should be installed and the connecting rod inspected for wear See Figure 8 NOTE Always use new O rings Cups Seal Rings Support Rings Guides Washers and Piston Cap Screws If new Valves are needed always replace the complete set of four Form L 0200P 6 11 Rev B Series 5300X 5321 5322 amp 5324 Disassembly Repair amp Reassembly Instructions NOTE Due to variations in each model s Piston or 6 Turn the Pump over and repeat Steps 1 through 5 Plunger Stack differences in the instructions for each model will be denoted with italics and brack 7 Position the Pump horizontally in the vise with the ets Safety Cover side up HAZARDOUS SUBSTANCE ALERT Always drain 8 Use a claw hammer to remove the Grease fitting and flush pump before servicing or disassembly See Figure 11 In most cases the Grease Fitting is damaged during removal and must be replaced Valve Assembly Removal At this time remove the Connecting Rod in Models 5321 amp 5322 1 Place the Pump upright in a bench mounted vise with the Safety Cover facing out then using a 9 16 wrench remove the Cylinder Head Bolts 2 Remove the Cylinder Head 3 Using a screwdriver or knife remove the Cylinder Head O ring from the Cylinder Head
30. p body until it bottoms out 8 Place the front Main Bearing on the Crankshaft until it touches the pump body 9 Place the smaller opening end of the Main Bearing Support Tool over the Crankshaft See Figure 19 10 Turn the Pump and Main Bearing Support Tool over so that the Safety Cover side of the pump is facing up 11 Position the Cam Bearing Support Tool with the bolt head down over the Safety Cover opening on the pump body Figure 19 12 Turn the bolt down by hand until it comes in con tact with the Cam Bearing 13 Use the arbor press ram to press down on the bolt in the Cam Bearing Support Tool to push the front Main Bearing into the pump bearing bore until it comes in contact with the first retaining ring on the crankshaft 14 Turn the pump over to install the Retaining Ring in the pump bearing bore Valve Assembly Installation 1 Lubricate the Pump Body Valve Bores 2 Install the Valve Assemblies into the INLET side valve bores with the plastic valve cage portion fac ing UP See Figure 20 3 Install the Valve Assemblies into the OUTLET side valve bores with the metal valve seat portion fac ing UP See Figure 21 4 Apply a small amount of grease to the top and bot tom inside surfaces of the Connecting Rod The area where the Cam Bearing comes in contact with the Connecting Rod plastic Valve Cage points Up Figure 20 5 Place the Connecting Rod on the Cam Bearing Form
31. sion loaded fasteners or devices Figure 17 4 Remove the first Retaining Ring on the Crankshaft with a pliers and the second Retaining Ring with a screwdriver 5 Press out the back Main Bearing in the same man ner as the front Main Bearing Refer to Steps 1 through 3 6 Remove the Slinger Ring by working it off the Shaft Reassembly 1 Install the back Main Bearing first Place the Bearing on the small opening end of the Main Bearing Support Tool with the Slinger Ring on top of the Bearing and position it on the arbor press WARNING Special attention should be exercised when working with retaining rings Always wear safety goggles when working with spring or ten sion loaded fasteners or devices 2 Place the Crankshaft in the Bearing and use the arbor press ram to press the Crankshaft through the Bearing until the Retaining Ring can be installed in the second groove of the Crankshaft See Figure 18 NOTE Make sure the Slinger Ring does not touch the Cam Bearing on the Crankshaft when installing Retaining Rings 3 Install both Retaining Rings on the Crankshaft Figure 18 N A 4 Place the Pump Body Safety Cover side down on the arbor press 5 Place the Crankshaft Back Bearing down into the bearing bore of the Pump Body 6 Place the Main Bearing Support Tool large open ing down over the Crankshaft 7 Use the arbor press ram to press the Crankshaft Assembly into the bearing bore of the pum
32. ssible Check alignment with a straight edge as shown See Figure 1 Make sure that belt has proper tension Too much tension will cause bearing wear too little will cause slippage See Figure 2 Check with belt and pulley sources for specific recommendation To figure proper diameter of pump pulley multiply motor engine RPM by diameter of the motor engine pulley and divide that figure by desired pump speed Pump Motor RPM x Motor Pulley Size Pulley Size Desired Pump Speed Refer to pump performance charts to determine desired speed to obtain desired maximum flow NOTE Shaft rotation can be either clockwise or coun terclockwise Four points of contact indicate alignment NOTE Pump may be mounted in other orientations with respect to the motor or engine Figure 1 Push the belt mid way between the pulleys check the deflection d and adjust d 0 016xL Figure 2 Direct Drive Flexible Coupling Installation First slide coupling ends onto motor engine and pump shafts as far as possible See Figure 3 Mount motor engine and pump onto base shimming pump or power unit so that shafts are aligned Leave enough space between ends of shafts to allow coupling disc to be inserted When alignment is made slide coupling ends over coupling disc Leave clearance between cou pling ends and center disc Tighten screws in both cou pling ends For electric motor drive use couplings rated at least twice the
33. tion port area in open screen area For example an area of approximately 1 1 to 1 9 square inches for a 1 2 suction port Be sure the screen is suitable for the liquid being pumped Keep the filter clean A clogged strainer will cause cavitation which usually leads to a poor performance and wear of the pump parts Form L 0200P 6 11 Rev B Compound Gauge Optional The pump should not be subjected to high suction line vacu ums To check on this install a compound gauge at pump inlet For ultimate performance and life the vacuum should be limit ed to 5 inches of mercury High vacuum conditions may cause premature product failure and void warranty Pulsation Dampener This device absorbs the shock and smooths out the pump dis charge pulsations providing smoother operation For the proper operation of many unloader valves the pulsation damp ener should be installed on the discharge side downstream from the unloader valve However for maximum system pro tection the pulsation dampener may be installed upstream from the unloader valve provided the unloader valve will func tion properly The dampener can be mounted vertically or horizontally Pressure Regulator Use a pressure regulator to limit incoming pressure to 20 psi when equipped with a suction side injector Volume pressure and horsepower figures in pump performance tables do not apply when incoming pressure exceeds 40 psi Pressure Gauge Dampener Use gauge capabl
34. ton will also come out with the Cylinder sleeve 3 Turn the pump around in the vise and repeat Steps 1 and 2 4 Remove the Connecting Rod 5 Remove the Piston Assembly from the Cylinder Sleeve by pushing it out with your fingers then remove the washer 6 Clean the cylinder sleeves using the burnishing adapter supplied with the tool kit The adapter is mounted to an electric motor shaft Insert the Cylinder Sleeve brass retainer end facing out into the furnishing adapter and polish the inside surface using a No 320 grit emery cloth Use a wire brush to clean the outside of the cylinder sleeve Upon inspection if pitting or scratches still show on the inside of the cylinder sleeve the cylinder sleeve must be replaced along with the cylinder sleeve o ring Crankshaft Assembly Removal All Models WARNING Special attention should be exercised when working with retaining rings Always wear safety goggles when working with spring or ten sion loaded fasteners or devices 1 Place the pump on a flat surface with the shaft side facing up then remove the retaining ring from the bearing bore 2 Using a metal pipe 3 in diameter by 4 1 2 high as a support fixture place the pump on the fixture shaft side down Position the fixture with pump on the arbor press See Figure 14 Figure 14 Place a bolt 3 8 in diameter by 4 1 2 long thread ed end up on the Crankshaft Cam Bearing then using the arbor press ram on th
35. w for Hollow Shaft Pump Key for Hollow Shaft Pump 1610 0007 2130 0007 Solid Shaft Sub Assembly see list ing above Key for Solid Shaft Pump Shield 2008 0001 1810 0013 1820 0025 Bearing Retaining Ring shaft Retaining Ring housing 1510 0041 3420 0030 Mounting Base for Solid Shaft Pump Torque Arm Kit for Hollow Shaft Pump Consists of 1 No 2820 0035 Torque Arm 1 No 1450 0003 Bumper and 2 No 2210 0064 Bolts Form L 0200P 6 11 Rev B atte 3396 0006 HYPRO SERIES 3396 0014 Liquid Injector Heads Model 3396 0014 for Hypro Series 5300 cast iron pumps with suffix X Model 3396 0006 for Hypro Series 5321 and 5324 cast iron pumps SPECIFICATIONS Cylinder Head Cast iron with special flow Inlet Port 1 8 NPT F can be positioned to face any direction Brass Valve Stem Needle type metering for accurate mixing of injected solution and liquid being pumped Unitized Valve Assembly Stainless steel valve spring ball and valve seat Nylon spring retainer b Control Knob Calibrated with 9 steps in a 360 turn y Q Can be rotated up to three times gg 0 Maximum Temperature 140 Fahrenheit 60 C Net Weight Model 3396 0014 1 Ib 8 oz 594 8 g Model 3396 0006 1 Ib 12 oz 793 2 g The Hypro Series 3396 Liquid Injector Head mounts directly on the pump replacing the regular cylinder head It feeds solution directly into the pump mi
36. xing it with the regular pump flow No internal pump parts are removed or disassembled to install the injector Amount of solution injected is regulated by a needle valve and adjusted by a calibrated control knob Positive seating ball type check valve prevents back flow of liquid from the pump into the injector This allows application of soap detergent and other solutions through the injector then by closing the injector supply followed by a clear water rinse through the pump The 1 8 NPT F inlet port can be positioned to face any direction A built in s flow regulator channel in the cylinder head compensates for various inches of Series 5300 Pump Series 5321 Pump mercury 127 mm Hg up to a maximum incoming pressure of 20 psi 137 8 with Model 3396 0014 with Model 3396 0006 kPa NOTE If incoming pressure is higher a pressure regulator must be Liquid Injector Head Liquid Injector Head used Add suffix letter D to pump model number MODEL 5320 MODEL 5330 MODEL 5321 MODEL 5324 HYPRO PISTON PUMP 2 GPM 3 GPM 2 2 GPM 2 9 GPM Pressure at Pump Outlet 500 psi 500 psi 1000 psi 800 psi Pump Inlet Conditions 5 Hg 10 psi 20 psi 5 Hg 10 psi 20 psi 5 Hg 10 psi 20 psi 5 Hg 10 psi 20 psi A oe Hlectes 9 OZ 6 OZ 5 OZ 10 oz f 9 oz 8 oz 11 1 2 oz 10 1 2 oz 8 oz 17 oz f 15 1 2 oz 13 oz Per Minute MODEL 5320 MODEL 5330 MODEL 5321 MODEL 5324 HYPRO PISTON RUME 7 57 L min 11 4 L min 8 3 L min 11 L
37. y No 5500 5318 14 pe Consists of one No 5501 5318 Crankshaft Sub Assembly two No 1810 0013 Retaining Rings two No 2008 0001 Main Bearings one No 2130 0007 Bearing Shield WEA Ee ta 900000Q00 Spec Pump No 53703 Hollow Shaft Sub Assembiv No 5501 5320 Consists of one No 0551 5320 Crankshaft one No 2007 0029 Cam Bearing one No 2405 0006 Grease Fitting Assembly one No 1610 0011 Key two No 2230 0017 Set Screws Hollow Shaft Assembly No 5500 5320 Consists of one No 5501 5320 Crankshaft Sub Assembly two No 1810 0013 Retaining Rings two Plunger Parts Kits No 2008 0001 Main Bearings one No 2130 0007 Plunger Stack Parts Kit No 3430 0291 sil ki Consists of two each of the following parts No 1440 0010 6 Seal Rings No 1440 0037 Guides No 1720 0064 O rings No 1720 0079 O rings No 2150 0027 Seal Assemblies NOTE When ordering parts No 2220 0039 Socket Head Cap Screws give QUANTITV PART NUM No 2270 0042 Washers and No 2270 0051 BER DESCRIPTION and COM Washers PLETE MODEL NUMBER Reference numbers are used Plunger Parts Kit No 3430 0292 ONLY to identify parts in the Consists of one No 3430 0291 Plunger Stack drawing and are NOT to be Parts Kit and two No 3500 0036 Plungers used as order numbers Ref Qty Part No Req d No Description 3430 0197 Set of four No 3400 0073 Unitized Valve Assemblies Consists of four each O ring Ref A Valve S
Download Pdf Manuals
Related Search