User`s Manual
Contents
1. The XERC CME SE User s Guide v1 00 Last updated 03 31 2007 sickmods net pablot com Intr ion Thank you for purchasing the premier case modder s IR device for the Xbox amp Xbox360 The XERC CME SE was designed by pablot and has been produced and distributed by sickmods net Please read this entire manual before beginning setup and visit http cme sickmods net for additional help or to ask any questions The CME Case Modder s Edition version of our XERC was designed to add advanced LED chasers that are controlled via the remote It is offered in 3 versions the C5 C6 and C7 These numbers refer to the number of ports used in the chaser sequences There are 7 ports total on the CME SE so the C7 will use all available ports to cycle through the LEDs The C5 version however uses the first 5 ports for the chasers and the additional ports toggle the LEDs connected to them either on or off To keep the chasers continuous you will want to wire your LEDs in multiples of the number of ports available For example if you have 12 LEDs in a circle you would need to use the C6 version The CME SE features a VU meter mode as one of its chasers This VU meter turns on the ports in order from H1 when the music is low to H5 H7 when the music peaks thus blinking your LEDs along with the beat of the music There are a total of 9 different modes that the H ports can be set to 8 for C5 plus on or off New to the CME SE are the2. Then press the H6 or H7 toggle button This will turn on or off the circuit connected to it by toggling whether it receives ground or not The H6 toggle is only available on the C5 version of the CME SE and the H7 toggle is only available on the C5 and C6 versions The C7 version uses all ports for the chasers so it does not use the toggle feature Controlling X Pads The X1 and X2 pads were made to allow the CME SE to be able to control other devices such as the LED Fader Deluxe This is done by setting the pads to be either Ov or PWR By default the pads are set to low low Each press of the X Pad Control button cycles the pads through the following order low low low high high low high high To use the X Pad Control button you must first turn the XERC on so the status light is on Be aware that this is only to be used as a high or low control signal for other devices and not for supplying power or ground to any circuit For assistance visit http forums sickmods net XERC CME SE User s Guide Page 6 Tr lesh in The LED does not blink when I plug in the Xbox Check that your XERC CME SE is connected to the correct points on the motherboard Specifically check PWR and GND Make sure your SL Status Light is connected properly Refer to the installation document for how to properly connect your own LED The remote is unresponsive Enter config and hold down a button on the remote If the status LED flickers then the XERC
3. X1 amp X2 pads These pads allows the CME SE to control add on devices such as the LED Fader Deluxe by providing either a high or low control signal In addition to the LED control the XERC CME SE also has power on off and eject features to remotely turn on your Xbox When you get the XERC CME SE it will be pre programmed with Pablot s open source code and will have a default button map for the Xbox DVD Kit remote or Xbox360 remote depending on which version you get pre configured This means that once you have connected the XERC you can instantly begin using it with no initial setup You can change this configuration if you wish or set up configuration for a different remote All settings on the XERC can be changed at any time without having to open your Xbox or connect it to a computer When you power off the console or even unplug the console the XERC retains all settings so when you plug it back in your remote codes and chaser settings will remain as you left them For assistance visit http forums sickmods net XERC CME SE User s Guide Page 2 Pr nfiguration The XERC CME SE comes with a default button map pre configured for either the Xbox DVD Kit remote or the Xbox360 remote depending on which version you get After installing your CME SE you can plug in your Xbox and the CME SE s status light should blink 4 times For the Xbox1 version you should now be able to press Short Power Press and have the Xbox boot up
4. is receiving a signal If it does flicker but will not program during config it may be an unsupported remote If the status LED does not flicker during config first test with a different remote If neither remote will cause the status LED to flicker check that the IR receiver is correctly installed The XERC CME SE has worked before but now one or all buttons are unresponsive Try using new batteries in your remote Enter configuration and reprogram the buttons The remote is responding but isn t doing the right commands Enter configuration and reprogram the buttons There might have been a missed command during configuration which caused all subseguent functions to be shifted over I can not enter config or use Safe Off but I can power on with the remote PB might not be connected right her Information The supported remotes for the XERC CME SE are RCA XBOX Philips RC 6 Newer Philips Remotes and XBOX 360 Remotes Full support for mode O normal remotes and partial support for mode 6A doesn t store customer code but accepts both short and exteneded customer code and only accepts 16bit information fields For assistance visit http forums sickmods net XERC CME SE User s Guide Page 7
5. The same button will turn the Xbox off when pressed for 2 4 seconds The power eject buttons are disabled for the Xbox360 remote by default since that remote already has that feature If the default layout is OK then you do not need to configure it and you are done If you would like to change the layout add remove features or set up use for another remote please follow the instructions in the next section hort P P fe Off Eject Safe Eject Short Power Press Safe O Long Power Press Safe Off Speed Up H6 Toggle C5 Only H7 Toggle C5 amp C6 Only XERC On Off Speed Down Chaser Direction Chaser Mode XERC CME SE Preset Configuration For assistance visit http forums sickmods net XERC CME SE User s Guide Page 3 Chaser Direction Chaser Mode Speed Up Speed Down H7 Toggle C5 amp C6 Only H6 Toggle C5 Only X Pad Control XERC On Off XERC CME SE Preset Configuration For assistance visit http forums sickmods net XERC CME SE User s Guide Page 4 nfiguration Configuration is setting up which buttons on your remote perform which functions To enter configuration turn the Xbox on then turn it off and keep the Xbox s power button held in until the XERC CME SE status LED blinks once then release the button This should take about five seconds The Xbox will remain off and your status LED will be dim You are now in the configuration mode where you will choose which buttons perform w
6. ave finished operating the CME SE turn it off by holding down the XERC On Off button for a couple more seconds until the status LED turns off If you turn the Xbox off the XERC also turns off automatically The XERC On Off button was created so you can use those same buttons without controlling the XERC normally and only control the XERC when you want to Changing Modes To cycle through the different chaser modes you must first turn the XERC on so the status light is on Then press the Chaser Mode button Each press will advance to the next chaser and when you reach the end of the list it will return to the beginning The chaser modes in order are Off On Strobe Alternate Spin Spin Hole 3 Spin C6 amp C7 only Changing Speed To change the speed of the chasers you must first turn the XERC on so the status light is on Then press the Speed Up or Speed Down button Be aware that at full speed some chasers will be going so fast that they appear to be on solid and at low speed they will be going very slow There are 8 steps that the speed can be set to Changing Direction This one is pretty self explanitory To change the direction of the chasers you must first turn the XERC on so the status light is on Then press the Chaser Direction button Some chasers such as VU and Strobe will not be affected by the direction H6 H7 Toggle To change the toggled state of these ports you must first turn the XERC on so the status light is on
7. been configured and config has ended Your new buttons are now programmed If the LED does not blink for one of the functions within a few seconds release the button and try again Function LED Flashes Button Assignment Will flash after programmed For your own use to record buttons S Short L Long used Skip Feature ssss bo XERCOnOf SSS Short Power Press Safe Off SS1 S Long PowerPress SafeOff SSP Eject Safe Eject SSS X Pad Control SSP Chaser SpeedUp SELF Chaser Speed Down tsss Jo O Change Chaser Mode L S S o O Change Chaser Direction _L S L S L L L L for C7 H7 Toggle C5 amp C6 Only L S L L L L L L for C6 H6 Toggle C5 Only Oo EN O For assistance visit http forums sickmods net XERC CME SE User s Guide Page 5 ration Turning the XERC on While the Xbox is on the XERC will not respond to any buttons other than Safe Off Safe Eject until you turn the XERC on To do this hold down the button programmed as XERC On Off for a couple seconds You will see the XERC s status light turn on solid indicating it is on and responding to your button presses While the XERC is on buttons programmed to do 2 things such as speed up the chaser and also move up in a menu will still do both things Keep this in mind so you don t accidentally control your Xbox in an unexpected way while trying to just control the CME SE Turning the XERC off Once you h
8. hich functions If you wish to abort config for any reason turn the Xbox on and config will abort and your configuration will remain the way it was before entering config The first button you will program will be a temporary Skip Feature button so use a button that will not be programmed for a main function Hold this button down briefly and the status LED will blink three four short short short short You will notice that while holding the button the status LED will flicker confirming it is receiving the signal If you come to a feature that you do not want to use hold down this Skip Feature button and the XERC 2 will skip that feature For example if you have no use for the Long Power button you can use the Skip Feature button to skip it After configuring the Skip Feature button hold down the button you wish to use to turn the Xbox on with a short power press and after a second or two the status LED will then blink short short short long This button will also become the Safe Off button To turn the Xbox off with this button hold it down for 2 4 seconds This is to prevent you from accidentally turning the Xbox off while navigating menus If you have an Xbox360 that already has power and eject buttons on the remote you can use the skip button to skip these buttons Continue this process for the remaining functions After you ve programmed the last function the status LED will blink long long long long confirming the last button has
Download Pdf Manuals
Related Search