OPAX-011GSM User Manual _Turkey_
Contents
1. Enter area code 03 for example and ended with NEW AREA 03 OK Area code has programmed successfully Note It is possible to program up to 4 digits Step 6 Setting the Function of Adding Area Code when Transmitting an Alarm To turn on off this function you can press 14 to proceed AREA ON amp amp OFF AREA ON amp GOFF 1 n To turn on this function simply press 1 To turn off this function simply press O ON amp amp OFF 1 AREA Default Value 0 Step 7 Setting the Delay Time for Transmitting a Dialing Number To set the delay time you can press 34 to proceed OPAX 011GSM USER MANUAL Rev 3 3 14 DTTRANSMIT DTTRANSMIT 00007 Example To set the required delay time at 7 seconds Simply press 000072 DTTRANSMIT 00007 Note The Delay Time is a 5 digits value range from 00000 99999 seconds Default 00004 seconds Step 8 Setting for calling a group of Administrator numbers To program the unit to dial a certain group of numbers for PSTN AC failure or Auto Test you can press 29 to proceed CALL CALL 5 ll Example Setting the unit to dial the first 5 administrator numbers Simply press 5 OK CALL 5 Step 9 Setting for Auto Test 9 1 Time Setting OPAX 011GSM USER MANUAL Rev 3 3 15 To setup time you can press 16 to proceed TI ME 08 30 00 Example To set the time at 8 30am Simply input digits2. uses 30mA while in idle state and 260mA when transmitting an alarm Wall mounting enclosure available The OPAX 011GSM units can be installed inside the alarm panel or inside its own wall mount enclosure 3 Installation Instructions Note It is essential that you read the step by step instructions fully prior to installing and programming the unit 3 1 Description Antenna connect the antenna to the GSM module place the antenna as far as possible from the OPAX 011GSM and do not leave any coiling of the antenna cable to avoid radiant interference SIM Card disable the PIN code and set it to 1234 default For Transmitter Mode Data or SMS as with any transmitter it requires an identifier receiver telephone numbers etc refer to the complete information on Programming page Line Input connect the line input to the PSTN or ISDN network Outputs Back Up Mode connect the RS232 DB15 to additional remote controlling outputs Alarm Input connect the input to output of the Alarm Panel Control Panel Power Supply connect to a 12V power supply Operating State Approximately 20s after power up check the operating state indicated by the Power LED the LED is steady during power up phase and then blinks when the connection to the GSM network is established The Signal indicator LED will stay lit whenever there is signal OPAX 011GSM USER MANUAL Rev 3 3 7 3 2 OPAX 011GSM Inputs and Outputs Wiri
3. ON amp GOFF 1 To enable this function simply press 1 To disable this function simply press 07 POWER UP MSG ON amp amp OFF 1 Default Value 0 Enable Disable System Armed SMS Notification The system is able to generate SMS notification whenever user armed the OPAX 011GSM To enable this function you can press 47 to proceed ARM MESSAGE ON amp amp OFF OPAX 011GSM USER MANUAL Rev 3 3 32 ARM MESSAGE ON amp amp OFF 1 To enable this function simply press 1 To disable this function simply press 02 ARM MESSAGE ON amp GOFF 1 Default Value 0 Activate Output Relay to stay on for a specific time via Voice To activate output relay 1 to stay on for a specific time you can press 21 to proceed RLY1 00050 RE 1 Example To activate relay 1 to stay on for 50 seconds and with SMS reply from the unit after relay has turned off Simply input 00050172 RLY1 00050 RE 1 OK Note RE stands for generation of SMS when relay off value ON 1 or OFF 0 You may continue to activate relay 2 or relay 3 by pressing 22 or 23 Setting the Alarm Time for Audible Alarm via Voice To set the alarm time for audible alarm you can press 33 to proceed OPAX 011GSM USER MANUAL Rev 3 3 33 ALARM 03600 Example To set the audible alarm to sound for 1 hour when triggered Simply press 036002 ALARM 03600 OK Note The alarm time must ent
4. input triggered open Default 0 OPAX 011GSM USER MANUAL Rev 3 3 23 CA2 stands for calling the administrators when input triggered close Default O Value ON 1 or OFF 0 You may continue to activate Input 2 Input 3 and Input 4 functions by pressing 25 or 26 Note Please refer to programming instructions via SMS for editing the Input Alert messages on page 27 Step 14 Arm and Disarm the System Via Fixed Line Phone To arm the system you can press 10 to proceed ARM OR DI SARM ON amp amp OFF ARM OR DISARM ON amp amp OFF 1 Example To arm the system simply press 1 To disarm the system simply press O ARM OR DISARM ON amp GOFF 1 System armed successfully Note n Armed mode the OPAX 011GSM can generate SMS alerts alarms and dialing the administrator numbers when the inputs triggered Auto Test PSTN failed or AC failed Alarm Indicator When dialing the Administrator numbers When Input 1 triggered it will generates Beep continuous sound When Input 2 triggered it will generates Beep x 2 continuous sound When Input 3 triggered it will generates Beep x 3 continuous sound When AC failed it will generates Beep x 5 continuous sound When PSTN failed it will generates Beep x 6 continuous sound When Auto Test it will generates Beep endless sound To acknowledge the above alarms simply press the below command on your phone and the system will s
5. M requested any PIN code If this is the case the PIN code can be disabled using the security settings on the phone Warning The OPAX 011GSM identifies only 3V SIM Card Proceed as follows 1 Slide back the SIM door and lift it up Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines up with the clipped corner of the SIM holder 3 Close the SIM door 4 Slide the SIM door to lock the SIM card in place 3 4 Power up the OPAX 011GSM When power up the OPAX 011GSM it will display as below LOADING gt gt gt gt gt OPAX 011GSM USER MANUAL Rev 3 3 9 WAI TI NG When the terminal is ready to use it will display as below C Semi LY Kt OPAX 011GSM Note Whenever the OPAX 011GSM fails to logon to network or fails to detect the SIM card it will restart automatically until it has detected the SIM card or successfully logon to network 3 5 Dialing a number from the attached telephone set Connect ta TELL After the GSM module is connected to the GSM network an attached fixed line phone can be used to make calls If you pick up the phone you will hear a dial tone Simply dial the number you want to call as if you are dialing from a normal fixed line phone You can also dial the OPAX 011GSM unit s phone number from another phone and its attached phone will ring as a normal landline phone would If there is a busy tone on the attached telephone set ei
6. OPAX 011GSM GSM MODULE User Manual Sketch of the OPAX 011GSM ANTENNA The antenna must be well connected before turn on the terminal Installation amp Connections TEL PORT 1 ALARM INPUT TEL PORT 2 Connect to Alarm Panel also function as Phone Input ANTENNA PORT ON OFF SWITCH Connect the provided Turn On or Off the antenna to the Terminal Terminal GSM MODULE Connect to PSTN Line POWER INDI CATOR RED The indicator is illuminated when mains power is present NETWORK INDI CATOR GREEN The indicator is illuminated when the terminal is connected to GSM Network OUTPUT Connect the RS232 DB15 female cable to the terminal for controlling outputs and inputs ae POWER PORT Connect a 12V Power Supply to the Terminal OPAX 011GSM USER MANUAL Rev 3 3 2 OPAX 011GSM USER MANUAL Wiring Diagram A Main Unit 1 cus the l Alarm Transmission ar 1a to fia DTMF SMS Connect to n the LED Modul jule li t a Con nect to the Internal 4 BOISE PSTN General Input for Alarm 12 CAVO System Pane v1 ower nect to Inputs panel Supply amp additional remote controlling outputs Wiring Diagram B DB15 Female Cable OPAX 011GSM USER MANUAL Rev 3 3 3 Please check the following packing list Name Quantity Unit OPAX 011GSM Main Unit 1 set Telephone line 1 set DB15 F cable set Power adapter set 5m GSM ter
7. TC Example of Return Message PSTN O I NPUT2 1 I NPUT3 O Input 2 triggered OPAX 011GSM USER MANUAL Rev 3 3 37 Permanent V Output Facility There is a permanent V output when the OPAX 011GSM is power on This output is available on the connection PI N8 and ground on the main board The output voltage is according to power supply used on OPAX 011GSM It can be used to power on other facility or device 8 Technical Specifications Environment temperature 0 50 C Relative humidity 10 95 Air pressure 86 106kpa Environment yawp lt 60dB A Working frequency GSM900MHz GSM1800MHz Stability of frequency better than 2 5PPM Signal sensitivity 103dBM Transmit power lt 2w Power 220v 15 AC Input Voltage Tolerances 1 20VDC The max distance between terminal and telephone 100M Oe M od ob cee ee Du E e oe e OPAX 011GSM USER MANUAL Rev 3 3 38 OPAX 011GSM USER MANUAL Rev 3 3 39
8. and ended with TI ME 08 30 00 9 2 Setting the Auto Test Report Time Section 1 The system has the function of sending the test report to the administrators at the programmable time section The time is entered in 24 Hour format To program the auto test report time section 1 you can press 17 to proceed Example To set the auto test report time at 12 00pm Simply input digits and ended with DSTMI 12 00 00 OK 9 3 Setting the Auto Test Report Time Section 2 OPAX 011GSM USER MANUAL Rev 3 3 16 The system has the function of sending the test report to the administrators at the programmable time section The time is entered in 24 Hour format To program the auto test report time section 2 you can press 42 to proceed Example To set the auto test report time at 18 00pm Simply input digits and ended with DSTM2 18 00 00 OK Note Skip this setting if only 1 time section is needed 9 4 Setting the Auto Test Report Time Section 3 The system has the function of sending the test report to the administrator at the programmable time section The time is entered in 24 Hour format To program the auto test report time section 3 you can press 43 to proceed Example To set the auto test report time at 23 59 pm Simply input digits and ended with DSTM3 23 59 00 OK OPAX 011GSM USER MANUAL Rev 3 3 17 Note Skip this setting if only 1 time section
9. are parameters do NOT enter the square brackets When you send a command you will receive the answer for the first time even if your GSM number is not in the administrator list This happens because the OPAX 011GSM recognizes any GSM number as administrator and answers to it Warning The administrator number must be programmed into the OPAX 011GSM unit first via voice mode in order to use SMS programming mode 5 1 Time Setting To set the time you can send the following SMS command to the unit The time is entered in 24 Hour format Text Command SETM HH MM SS HH stands for 2 digits value Hour MM stands for 2 digits value Minute SS stands for 2 digits value Seconds Example When SETM 08 30 15 is applied the time 08 30 15 will be stored inside the OPAX 011GSM memory Return Message SETM OK 5 2 Editing the Message Contents of Auto Test Up to 50 Characters OPAX 011GSM USER MANUAL Rev 3 3 26 The message contents can be edited and programmed up to 50 characters You can change the displayed text by sending the following commands by SMS message to the unit Note Only support normal abc ABC English text no special characters Text Command TSMS XXXXXX XXXXXX stands for message contents Example If you want the SMS Report to display Status Online you would send the following SMS message to the unit TSMS Status Online Return Message TSMS Status Online 5 3 Editing the I n
10. e Step 2 Reset the OPAX 011GSM Unit To reset the unit you can press 15 to proceed REST ON amp OFF REST ON amp OFF 1 Then press 1 to reset REST ONGOFF 1 Note It is advised that you should reset the OPAX 011GSM unit before proceeding to the below programming section Step 3 Programming the Administrator Number Continue pressing 1 to start programming the administrator number 1 TEL 13232353646 1 Enter administrator number 13232353646 for example and ended with OPAX 011GSM USER MANUAL Rev 3 3 12 TEL OK Number has programmed successfully You may continue to program administrator number 2 3 4 5 6 7 and 8 by pressing 2k 3 4 5k f 6 7 8 Note It is possible to program up to 16 digits for a telephone number Step 4 Setting the Recipient that will receive Alert Messages The unit can send text alerts to 1 or all 8 of the programmed administrator s numbers To do this setting you can press 18 to proceed SECT SECT 11111111 Example To turn on this function for all recipients Simply input 111111117 SECT 11111111 OK Note The input for this setting is an 8 digits value ON 1 or OFF 0 only Each of them represents administrator 1 8 Default Value 10000000 Step 5 Programming the Area Code To program area code you can press 9 to proceed OPAX 011GSM USER MANUAL Rev 3 3 13 NEW AREA 03
11. er in 5 digits range from 00001 99999 Default 00010 seconds Setting the OPAX 011GSM to ignore the front dialing digits when dialing the Administrator via Voice This function is useful when the OPAX 011GSM is connected to the PABX system where Access Digits are required for Extension Line Centrex Line To set the unit to ignore the front dialing digits you can press 44 to proceed DEL NUM DEL NUM 2 ii Example To set the unit to ignore first 2 dialing digits Simply press 2 DEL NUM 2 OK Note The value is 0 4 Default O OPAX 011GSM USER MANUAL Rev 3 3 34 OPAX O11GSM USER MANUAL Adjusting the Speaker and Microphone Volume level via Voice To adjust the speaker and microphone volume level you can press 11 to proceed SPK 3 MI C 3 Example To adjust the speaker volume to 3 and microphone volume to 3 Simply press 334 SPK 3 MI C 3 OK Note Both SPK and MIC volume level range from 1 4 Default 1 Adjust the speaker and microphone volume to compatible with your alarm panel I nquire the Software and Hardware Version of OPAX 011GSM via Voice To check the software and hardware version of OPAX 011GSM unit you can press 13 to proceed HW l lver SW 4 7 ver MW 3 2ver The information will be displayed on screen Press to turn back Inquire All Programmed Administrator Number via SMS To inquire all the programmed administrator you can se
12. is needed 9 5 Enable Disable the function of dialing the programmed Administrator number for Auto Test To turn on this function you can press 27 to proceed DTI MEC ON amp amp OFF DTIMEC ON amp amp OFF 1 To turn on this function simply press 1 To turn off this function simply press O DTI MEC ON amp GOFF 1 Default Value 0 9 6 Enable Disable the generation of SMS Report for Auto Test To turn on this function you can press 28 to proceed DTI MEM ON amp amp OFF DTIMEM ON amp GOFF 1 To turn on this function simply press 1 To turn off this function simply press O DTI MEM ON amp GOFF 1 OPAX 011GSM USER MANUAL Rev 3 3 18 Default Value 0 Note Please refer to programming instructions via SMS for editing the message content of Auto Test on page 26 Step 10 Setting for PSTN Failure To turn on this function you can press 30 to proceed PST ME OU AL CA1 CA2 PST ME 10U 1 AL 1 CA 1 CA2 1 Example Setting the unit to generate an Alert Message call the administrators generate a pulse V and sound the audible alarm when PSTN failed Simply input 11111 PST ME 1 OU 1 AL 1 CA 1 CA2 1 OK Description ME stands for generation of SMS when PSTN failed Default 0 OU stands for generation of pulse V at PIN15 when PSTN failed Default O AL stands for sounding the audible alarm when PSTN failed Defaul
13. minal antenna set User s Manual set 1 Introduction to OPAX 011GSM GSM Alarm SYSteM 0cecnewsnenems sms nmm mmm D 2 Main Features or the OPAX OTLTIGSM s ne viw interwar emen A Eras ax aee cus dese ida Moda dO 3 Installation Instructio usos vea pau uf at cust deu Fest itte tint vtt dte cione edocet os Sb edo ea ea Co be o dius 7 m m m GNI B regleidiolq E M NE an a cA 3 2 OPAX 011GSM Inputs amp Outputs Wiring INStrUCTIONS cae teenie nmm meme e D 2 3 Thstallingitlie SIM Gabe cce matu oou uda em n d E m M de eC i uS Geen une M dc cun 3 4 Power Up the OPAX OIIGSM e dti needa erudi tacet a aeu tna piace sand cha er utatur E 3 5 Dialing a number from the attached telephone set eceisseseeeseiese mmm meme on oO LO 4 OPAX 011GSM Configuration Instructions Via Voice eisscecese emm mm m meme emenesll A PAINOA Oi E E A A a a a ek Stepl Enter Programming Mode eto es Yee a a a A M PAL d n eua ecu anaa AL St p2 Reset the OPAX OLIGSM Wiles invoice hens eoo angst Tecno cet a a eee ew 2 Step3 Programming the Administrator Number sisseseissese mmm mns LD Step4 Setting the Recipient that will receive Alert Messages sisse mmm mns 13 Step5 Programming the Area Ode irs uoi eeokesmrRuc Eden ElUs iens DRE Sa E Ead mus due aan candid Step6 Setting the Function of Adding Area Code when Transmitting an Alarm 14 Step7 Setting the Delay Time for Transmitting a Diali
14. nal strength you can press 20 to proceed Yall CSQ lt 23 gt The signal strength will be displayed on screen OPAX 011GSM USER MANUAL Rev 3 3 30 Press to turn back Setting the Waiting Time for Engaged Call via Voice In the event the administrator has not answered the call or engaged it could take a while for the OPAX 011GSM to call the next number You can shorten the time for every call by programming the waiting time Press 12 to proceed WAIT TI ME WAIT TIME 20 Example To set the waiting time for 20 seconds Simply input 20 and ended with WAIT TIME 20 OK Note The waiting time is a 2 digits value range from 20 59 seconds Default 30 seconds Setting Arm Delay Time Input 1 Only Input 1 can be programmed to arm after a preset time when the Arm button is pressed or Arm function is activated by fixed line phone To program the delay time you can press 45 to proceed ARM TI ME ARM TI ME 30 OPAX 011GSM USER MANUAL Rev 3 3 31 Example To set the arm delay time for 30 seconds Simply input 30 and ended with Note The Arm Time is a 2 digits value range from 00 59 seconds Default 00 seconds Enable Disable System Power Up SMS Notification The system is able to generate SMS notification whenever the OPAX 011GSM is turned on To enable this function you can press 46 to proceed POWER UP MSG ON amp amp OFF POWER UP MSG
15. nd the following SMS command to the unit Text Command ADM OPAX 011GSM USER MANUAL Rev 3 3 35 OPAX O1TIGSM USER MANUAL Example of Return Message 1 13256997049 2 15915325252 3 13456679988 oe ee Checking the Signal Strength via SMS To check the signal strength of the unit you can send the following SMS command to the unit Text Command CSQ Example of Return Message CSQ lt 28 gt Checking the Current Time Status via SMS To check the current time you can send the following SMS command to the unit Text Command ASTM Example of Return Message TI ME 01 35 50 Changing the Programming Mode Password via SMS It is possible to change the login password by sending the following SMS command Text Command PAWOZXXXXXX XXXXXX stands for 6 digits New Password Example OPAX 011GSM USER MANUAL Rev 3 3 36 To change the password to 654321 you would send the following SMS command to the unit PAWO 654321 Return Message PAWO OK Reset the OPAX 011GSM unit via SMS To reset the unit you can send the following command by SMS to the unit Text Command REST XXXXXX XXXXXX stands for 6 digits password based on PAWO Default 123456 and it can be changed anytime Return Message REST OK I nquire the Status of Inputs PSTN and AC To inquire the status of inputs PSTN and AC you can send the following SMS command to the unit Text Command C
16. nd the following text command to unit Text Command DARM X X stands for ON 1 or OFF 0 value Example To arm the system you can send the following text message to the unit DARM 1 Return Message ARM To disarm the system you can send the following text message to the unit DARM 0 OPAX 011GSM USER MANUAL Rev 3 3 28 OPAX 011GSM USER MANUAL Return Message DI SARM 6 Miscellaneous Settings I nquire All Programmed Administrator Number via Voice To inquire all administrator numbers you can press 32 to proceed 1 1234567890 ui All the administrator numbers will be displayed in sequence Deleting the Administrator Number via Voice Example To delete the programmed administrator number 1 you can press 1 to proceed Simply press to delete OPAX 011GSM USER MANUAL Rev 3 3 OPAX 011GSM USER MANUAL DEL1 OK Changing the Programming Mode Password via Voice To change the 6 digits programming mode password you can press 0 to proceed NEW PASSWORD NEW PASSWORD 654321 Input new password and ended with NEW PASSWORD 654321 OK I nquire the status of the Recipients that will receive Alert Messages via Voice To inquire the status of the recipients you can press 19 to proceed RECI PI ENTS 11111111 The status will be displayed on screen Press to turn back Checking the Signal Strength via Voice To check the sig
17. ng Instructions RLY1 OUT1 RLY2 OUT2 RLY3 OUT3 Remote Controlling Outputs These open collector outputs can be turned on and off remotely through a SMS Remote control will be reachable by sending a SMS with a certain command Note When sending normal SMS with command below the OPAX 011GSM will turn On Off the output relay and reply a message of output has turned On Off to a programmable phone numbers ZONE1 IN1 ZONE2 IN2 ZONE3 IN3 Inputs Connect ZONE1 ZONE2 and ZONES to inputs panel when there is a short circuit impulse on ZONEI1 ZONE2 ZONE the OPAX 011GSM is possible to send SMS to a programmable phone numbers For Example ZONE3 is connected to an electrical door when there is intruder or the electrical door is opened illegally OPAX 011GSM will receive short circuit impulse on ZONE3 and will automatically send a signal to the monitoring station and also send a SMS to notify the owner wa wa wu p pp LJ a E art r e G3 E E uz ny I ya d Cr i SSS JF M BODAS Rye an L _ _ 12 ry Em E d LV he Ld p i yi Tae 12v OPAX 011GSM USER MANUAL Rev 3 3 8 LAPUT Inputs and Outputs Wiring Diagram 3 3 Installing the SIM Card Note Installing the SIM Card Please be sure the initial 4 digit PIN code of SIM card is disabled This can be done by placing it in an unlocked Mobile phone and first checking if the SI
18. ng Number seem L4 Step8 Setting for calling a group of Administrator esses mmm LD Step9s Sattiliq TOF AUEtO TOSE sso rub voe erue cid o e eee cuc Tabor E OLD vec ie eters LD SteplO Setting for PSTN Fale cuiusmodi EcE E a duabieo ule bus unde a E uir asas d Steplil Setting Tor AC Failure esas enki du uie easet eara r le ey ceased ne tui eame tS asso aM Step12 Setting for Overcoming GSM Jammers amp GSM Tower Failure eese 2L Stepls Input Setth suxooka mers cd u er smiBhR pede rds tuit ues pede a cd estu MID DE DL EM OM eke O Stepl4 Armand Disarm the Systelisaiuie o eov fanat soo Breve Bud ot quete rd ui per Dude it educa zd Step15 Setting the Automatic Call Answering Feature esses seem nmm ns 24 5 OPAX 011GSM Configuration Instructions Via SMS cesis nmm mmm mmn 20 Deb Time 5 Cll NO Mee RU TT EE o 5 2 Editing the Message Contents of Auto Test ssseseieieeeeei seem meme meme mmn LO 5 3 Editing the Input Alert MessaQge5 sS bot Loo d usi erar edat dee Pasos C oer Crete eue baec datur Ji Dd OHEDUESOEEITGOS unctus aeta ceradiiu ceca hone lena E M dust m UE uS Co SOLDI MID M m SL Lu T 5 5 Arm and Disarm the System Via SMS sisiseelelei seem emm emmememiminissimiuiniuruseieiniuiniuiuis 20 6 Miscellaneous Settings acd reset pud Uoc abad Dwews i E aureus elena ide cos mcH QU pWwbE E Ed ci DD MNE eeejersieus ctm 38 OPAX 011GSM USER MANUAL Rev 3 3 4 l I
19. ntroduction to the OPAX 011GSM GSM Alarm System The OPAX 011GSM GSM Terminal is a wireless communicator for alarm and fire panels that uses the cell phone network GSM to transmit alarms and other panel event The module checks the status of the PSTN line and in case the PSTN line becomes unavailable the OPAX 011GSM GSM emulate the line signal to the panel At this time the panel will dial out using the GSM cell phone network to communicate with the receiver at the monitoring station and transmit the alarms GENERAL OVERVI EW Nobile wm uel um ums m moa me cii im Tm Um ca ma e Um mal Om n d m a cms HENCTUEUNUETENIF EFUTEUEEMSNENNPTETUETENHN Nobile Transmission Recephes en Processing by Standard Receiver operater OPAX 011GSM USER MANUAL Rev 3 3 5 Aerie gibi os EGGGEGEGEE HOEGGGGEGAEGAEM BHBEGEGNEEEAaSBNM 2 Main Features of the OPAX 011GSM Panel compatibility Allows any contact ID alarm panel to transmit alarms over GSM using the GSM voice channel Works over the GSM cell phone networks Units can be used wherever there is cell phone coverage Telephone line backup OPAX 011GSM give priority to the lowest cost network OPAX 011GSM uses the telephone line as the main transmission line and uses the GSM voice channel as backup Auto restart system t can continuously monitor the system status of its own When there is a problem with the SIM card or the module is n
20. ot working properly it will automatically restart the system Sends text messages to user programmable cell phone number SMS The OPAX 011GSM can be programmed to send a SMS to a programmable cell phone number to notify the user that the PSTN line has been cut off or unavailable It is possible to arm disarm the unit remotely via remote control SMS or phone call Alternatively it also can connect to the basic telephone to perform arm disarm Three digital inputs The system has the function to send SMS and call to the user in the event of input triggered For example Zone 3 connected to an electric door when there is intruder or the electric door is open illegally OPAX 011GSM will receive short circuit impulse on Zone 3 and automatically sends a signal to the pre set number and notify the owner OPAX 011GSM USER MANUAL Rev 3 3 6 8 10 11 Three remote control outputs These open collector outputs that can sink max 300ma per output can be turned on and off remotely through a SMS or phone call Remote control will be reachable by sending a SMS or phone call with a certain command For example SMS Call in to switch on lighting air conditional generator sensor or other equipment Standby rechargeable battery to prevent power failure or electricity cut off by intruder The GSM will function as normal when no electricity supply LCD display to check the GSM signal strength and battery capacity Low power consumption
21. puts Alert Messages Up to 50 Characters The Input Alert Message can be edited and programmed up to 50 characters You can change the displayed text by sending the following commands by SMS message to the unit Note Only support normal abc ABC English text no special characters Text Command USE N XXXXXX N stands for Input number 1 3 XXXXXX stands for alert message content Example If you want the alert message to display Garage Opened when input 1 triggered you would send the following SMS message to the unit USE1 Garage Opened Return Message USE1 Garage Opened 5 4 Output Settings 5 4 1 Activate Output Relay to Stay On for a Specific Time OPAX 011GSM USER MANUAL Rev 3 3 27 To activate the output relay you can send a text command via SMS specifying the number of seconds the output should stay on to the unit It is possible to set up to maximum of 99 999 seconds Text Command RLY N Z XXXXX N stands for Output number 1 3 XXXXX stands for 5 digits value The number of seconds 00000 99999 For example assume you want to turn on the output relay number 2 for 1 hour you would send the following SMS message to the unit RLY2 03600 Return Message RLY2 03600 Sending the following SMS Message to unit would mean turn off the output relay number 1 RLY1 00000 5 5 Arm and Disarm the System Via SMS It is possible to arm and disarm the system by SMS You can se
22. so has a second permanent V output continuously supplied from the battery backup via PIN7 output of the unit which will remain available for the period of AC unavailable Auxiliary V Output when AC Failure PI N7 OPAX 011GSM USER MANUAL Rev 3 3 20 Note Power Down Output facility can be used on alarm panel for alert notification Step 12 Setting for Overcoming GSM Jammers amp GSM Tower Failure 12 1 Enable Disable the function of Activate Output Relay 1 when GSM lammers is detected To turn on this function you can press 38 to proceed NETWORK ON amp amp OFF NETWORK ON amp GOFF 1 To turn on this function simply press 1 To turn off this function simply press O NETWORK ON amp GOFF 1 OK 12 2 Setting the Parameter for Network Failure To set the parameter you can press 39 to proceed NETDTI1 RLY1 NETDT1 05 RLY1 05 Example To set the network failure time for 5 seconds and the turn on time of Relay 1 for 5 seconds Simply press 0505 OPAX 011GSM USER MANUAL Rev 3 3 2l NETDT1 05 RLY1 05 OK Description NETDT1 stands for network failure time range from 00 59 seconds Default 6 seconds RLY1 stands for turn on time of Relay 1 when network fails 00 59 seconds 00 means RLY1 will stay ON permanently 12 3 Enable Disable the function of Activate Output Relay 2 when GSM Tower Failure To turn on this function you can pre
23. ss 40 to proceed NO SIGNAL ON amp amp OFF NO SIGNAL ON amp GOFF 1 To turn on this function simply press 1 To turn off this function simply press O NO SIGNAL ON amp amp OFF 1 OK 12 4 Setting the Parameter for GSM Tower Failure To set the parameter you can press 41 to proceed NETDT2 RLY2 NETDT2 06 RLY2 10 OPAX 011GSM USER MANUAL Rev 3 3 22 Example To set the network failure time for 6 seconds and the turn on time of Relay 2 for 10 seconds Simply press 061072 NETDT2 06 RLY2 10 OK Description NETDT2 stands for network failure time range from 00 59 seconds Default 6 seconds RLY2 stands for turn on time of Relay 2 when network fails 00 59 seconds 00 means RLY2 will stay ON permanently Step 13 Input Settings 13 1 Turn on the function of Inputs To turn on the function of input number 1 you can press 24 to proceed INI OP 1 CL 1 AL 1 CA1 1 CA2 1 Example Setting the input 1 to generate an SMS call the administrators and sound the audible alarm when it triggered Simply input 111117 INI OP 1CL 1 AL 1 CA1 1 CA2 1 OK Description OP stands for generation of SMS when input triggered Open Default O CL stands for generation of SMS when input triggered Close Default 0 AL stands for sounding the audible alarm when input triggered Default 0 CA1 stands for calling the administrators when
24. t O CA1 stands for calling the administrators when PSTN failed Default O CA2 stands for calling the administrators when PSTN connected Default 0 Value ON 1 or OFF 0 Auxiliary PSTN Failure Output Facility via PIN15 In additional to the alarm and text alert on PSTN failure the system also has a permanent V output continuously supplied from the unit via PIN15 output which will remain available for the period of PSTN unavailable Auxiliary V Output when PSTN Failure PIN15 OPAX 011GSM USER MANUAL Rev 3 3 19 Note PSTN Failure Output facility can be used on alarm panel for alert notification Step 11 Setting for AC Failure To turn on this function you can press 31 to proceed ADC ME AL CA1 CA2 ADC ME 1 AL 1 CA1 1 CA2 1 Example Setting the unit to generate an Alert Message call the administrators generate a pulse V and sound the audible alarm when AC failed Simply input 1111 ADC ME 1 AL 1 CA1 1 CA2 1 OK Description ME stands for generation of SMS when AC failed Default 0 AL stands for sounding the audible alarm when AC failed Default O CA1 stands for calling the administrators when AC failed Default 0 CA2 stands for calling the administrators when AC connected Default 0 Value ON 1 or OFF 0 Auxiliary Power Down Output Facility via PI N7 In additional to the alarm and text alert on AC failure the system al
25. ther the line you are calling is busy or the GSM communicator is busy with previous communication at that moment for example data transfer to the monitoring station Note Some telephone sets are sensitive to the GSM radio signal For this reason you may hear a characteristic noise in the telephone receiver when calling If the noise is disturbing change the location of the phone set try to keep it as far as OPAX 011GSM USER MANUAL Rev 3 3 10 OPAX 011GSM USER MANUAL possible from the OPAX 011GSM unit antenna Usually it is possible to find a suitable location for the phone with minimal level of interference 4 OPAX 011GSM Programming Instructions Via Fixed Line Phone Introduction The OPAX 011GSM can be programmed manually by a connected normal telephone Connect ta TELL Note Before commencing programming it is advisable to read the below programming setting instructions thoroughly To start with programming user must plug in a normal single line phone to TEL1 Port 1 Step 1 Enter Programming Mode Pick up the handset or press hands free press 123456 to enter programming mode If the password has entered correctly you should see HAND FREE displayed on OPAX 011GSM screen Now you may proceed with programming settings ENTER SETTING When pick up the handset ENTER OK SETTING OPAX 011GSM USER MANUAL Rev 3 3 ll Password entered correctly Programming Mod
26. top calling you OPAX 011GSM USER MANUAL Rev 3 3 1234562 Default password 123456 Note If the wrong password is entered the system will still continue to call the administrators Step 15 Setting the Automatic Call Answering Feature The OPAX 011GSM can be programmed to answer all incoming calls automatically even there is no fixed line phone attached to it When the call is answered it allows the owner to arm or disarm the system by entering a command from their phone s keypad To turn on this function you can press 35 to proceed AUTO ANSWER ON amp amp OFF AUTO ANSWER ON amp amp OFF 1 To turn on this function simply press 1 To turn off this function simply press O AUTO ANSWER ON amp GOFF 1 Default Value 0 Note Once this function is turned on the attached fixed line phone will not ring when there is an incoming call Arm and Disarm Command via Voice Press 123456 to arm the system when OPAX 011GSM answered the call Press 123456 to disarm the system when OPAX 011GSM answered the call Note 123456 is a 6 digits password that is programmable by O0 function or PAWO Z command by SMS at page 29 and page 36 OPAX 011GSM USER MANUAL Rev 3 3 25 OPAX 011GSM Programming Instructions Via SMS Programming the OPAX 011GSM can also be done via SMS commands using your phone Any programming command sent by SMS must be in CAPITAL letters The fields between square brackets
Download Pdf Manuals
Related Search