General Communication Service R6
Contents
1. button b By Clicking on Save All if want to save all scanned nodes Click on OK in Scan Results Save all dialog window Click on Select All and Save buttons in Scan Results Selection for Database Saving dialog and click on close button to close the window Click on close button in Scan dialog window 6 Close GCS Connection Tool using Exit button EXPECTED RESULTS Connection Tool started successfully Connection is successfully created Connection is successfully saved to the GCS database Node is successfully scanned Node is saved in the GCS database without any errors GCS Connection tool is closed successfully NoRWND 7 5 Pipe Connection to DCN Adaptor C4 X TEST PURPOSE The purpose of this test case is to verify Q1 Pipe Connection to DCN Adaptor C4 x PRECONDITIONS Q1 elements are commissioned and connected to DCN Adaptor C4 x Network connection to DCN Adaptor C4 x is operational and IP address of DCN Adaptor C4 x Q1 Pipe parameters username password and bus number are known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool 2 Create a Nokia Q1 Pipe Connection to Q1 Node In database tab select Connections radio button Click on Add button Enter name to the connection in Name edit box Select Nokia Q1 Pipe Connection2. e Click on Start button 5 Save the scanned nodes if listed in grid box a By clicking the button Save button Click on Save button in Save Node dialog window Close Scan dialog window by clicking Close button b By Clicking on Save All if want to save all scanned nodes Click on OK in Scan Results Save all dialog window Click on Select All and Save buttons in Scan Results Selection for Database Saving dialog and click on close button to close the window Click on close button in Scan dialog window 6 Close GCS Connection Tool using Exit button EXPECTED RESULTS Connection Tool started successfully Connection is successfully created Connection is successfully saved to the GCS database Node is successfully scanned Node is saved in the GCS database without any errors GCS Connection tool is closed successfully O OV OO O 7 7 BTS Connection TEST PURPOSE The purpose of this test case is to verify BTS Connection PRECONDITIONS Nokia Siemens Networks NetAct Framework has a standard configuration and commissioning has been carried out successfully NetAct osscore IP BSC ID BCF ID ornuser password and Q1 NE address are known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool 2 Create a BTS Connection to Q1 Node In database tab select Connec
3. available in GCS installable disk Click Next on General Communication Service R6 2 InstallShield Wizard Select Complete radio button in setup type dialog of the wizard and click on Next button Click on Install button in Ready to install the program dialog Click on Finish to complete the installation 2 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool 3 Check if the below GCS Services are installed and started successfully in Services List from Control Panel gt Administrative Tools gt Services a b C General Communication Service General Communication Service Sync and General Communication Service Q1DB EXPECTED RESULTS 1 GCS is installed successfully without errors 2 GCS is launched successfully 3 Services are installed and started automatically 5 UPGRADE 5 1 Upgrade from GCS R5 x to GCS R6 2 TEST PURPOSE The purpose of this test case is to verify upgrade from GCS R5 x to GCSR R6 2 PRECONDITIONS 1 GCS R5 x installed DOUMENTATION GCS User Manual TEST EXECUTION 1 Install GCS R6 2 using General Communication Service R6 2 msi a Double click on General Communication Service R6 2 msi available in GCS installable disk b Click Next on General Communication Service R6 2 InstallShield Wizard c Select Complete radio button in setup type dialog of the wizard and click on Next butt
4. button after selecting the each connection definition parameters e Network Parameters HOST NAME and PORT of the Spider Port e Terminal Password Parameters PASSWORD Keep other parameters with default values 3 Save itin the GCS database by clicking Save button 4 Scan the above saved connection for a known range of Q1 addresses a In database tab select Connections radio button b Select the saved connection in steps 2 3 c Click on Scan button d In Scan dialog Enter Q1 Address range in Begin and End edit boxes e Click on Start button 5 Save the scanned nodes if listed in grid box by clicking the button Save and close the save and scan dialogs by clicking on Close buttons 6 Close GCS Connection Tool using Exit button EXPECTED RESULTS Connection Tool started successfully Connection is successfully created Connection is successfully saved to the GCS database Node is successfully scanned Node is saved in the GCS database without any errors GCS Connection tool is closed successfully O EE OO 7 10 Test Communication TEST PURPOSE The aim of this test case is to verify that connections saved to GCS database can be used by other applications PRECONDITIONS Node Manager or MSTE which is compatible with GCS R6 2 is available and installed to PC DOCUMENTATION Node Manager s on line help TEST EXCECUTION To run this test case follow instructions from node manager s u
5. c General Communication Service Q1DB EXPECTED RESULTS 1 GCS is installed successfully without errors 2 GCS is launched successfully 3 Services are installed and started automatically 6 Enhancements 6 1 Enhanced Import logging TEST PURPOSE The purpose of this test case is to verify that the failure messages are logged into event viewer while scheduling of Q1DBTool for importing 2G Node details from NetAct database to GCS database Also verify that the messages are logged into log file when logfile switch is used PRECONDITIONS 1 2 Oracle Client is installed and NetAct database server details are configured successfully through Oracle Net Configuration Assistant The passwords have been saved for Q1DBTool tool TEST EXECUTION 1 2 11 12 13 Log in the Node Manager Server as an administrator or with equivalent rights In the Node Manager Server select Start gt Programs gt Accessories gt System Tools gt Scheduled Tasks Double click Add Scheduled Task And click Next In the Scheduled Task Wizard Click Browse Find and select the location where you have installed Q1DBTool exe The default installation path is c Program Files Nokia Q1IDBTool exe and then Click Next Fill in the name for the import and Set the frequency Click Next Select the values for the start time when this task is to be executed Click Next Fill in the administrator user name a
6. Keep other parameters with default values Save it in the GCS database by clicking Save button Scan the above saved connection for a known range of Q1 addresses a In database tab select Connections radio button b Select the saved connection in steps 2 3 c Click on Scan button d In Scan dialog Enter Q1 Address range in Begin and End edit boxes e Click on Start button Save the scanned nodes if listed in grid box a By clicking the button Save button Click on Save button in Save Node dialog window Close Scan dialog window by clicking Close button b By Clicking on Save All if want to Save all scanned nodes Click on OK in Scan c Results Save all dialog window Click on Select All and Save buttons in Scan d Results Selection for Database Saving dialog and click on close button to close the window Click on close button in Scan dialog window papo 6 Close GCS Connection Tool using Exit button EXPECTED RESULTS Connection Tool started successfully Connection is successfully created Connection is successfully saved to the GCS database Node is successfully scanned Node is saved in the GCS database without any errors GCS Connection tool is closed successfully OnrwNr 7 4 Q1 Pipe Connection to Q1Agent TEST PURPOSE The purpose of this test case is to verify Q1 Pipe Connection to Q1Agent PRECONDITIONS Q1 elements are
7. commissioned and connected to Q1 Agent Network connection to Q1 Agent is operational and IP address Q1 Agent Q1 Pipe parameters username password and bus number are known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool 2 Create a Nokia Q1 Pipe Connection to Q1 Node a In database tab select Connections radio button b Click on Add button c Enter name to the connection in Name edit box d Select Nokia Q1 Pipe Connection from Type drop down list box e Enter following parameters information by clicking on Properties button after selecting the each connection definition parameters e Network parameters HOST NAME and PORT of the Q1 Agent e Q1 Pipe parameters USERNAME PASSWORD BUS NUMBER e Keep other parameters with default values 3 Save it in the GCS database by clicking Save button 4 Scan the above saved connection for a known range of Q1 addresses a In database tab select Connections radio button b Select the saved connection in steps 2 3 c Click on Scan button d In Scan dialog Enter Q1 Address range in Begin and End edit boxes e Click on Start button 5 Save the scanned nodes if listed in grid box a By clicking the button Save button Click on Save button in Save Node dialog window Close Scan dialog window by clicking Close
8. from Type drop down list box Enter following parameters information by clicking on Properties button after selecting the each connection definition parameters e Network parameters HOST NAME and PORT of the DCN Adaptor e Q1 Pipe parameters USERNAME PASSWORD BUS NUMBER e Keep other parameters with default values 3 Save it in the GCS database by clicking Save button Dango 4 Scan the above saved connection for a known range of Q1 addresses a In database tab select Connections radio button b Select the saved connection in steps 2 3 c Click on Scan button d In Scan dialog Enter Q1 Address range in Begin and End edit boxes e Click on Start button 5 Save the scanned nodes if listed in grid box a By clicking the button Save button Click on Save button in Save Node dialog window Close Scan dialog window by clicking Close button b By Clicking on Save All if want to save all scanned nodes Click on OK in Scan Results Save all dialog window Click on Select All and Save buttons in Scan Results Selection for Database Saving dialog and click on close button to close the window Click on close button in Scan dialog window 6 Close GCS Connection Tool using Exit button EXPECTED RESULTS Connection Tool started successfully Connection is successfully created Connection is successfully saved to the GCS database Node is successfully sc
9. to be used only with General Communication Service R6 2 delivery General Communication Service R6 2 has an online help and User manual PREREQUISITES Prerequisite for a successful General Communication Service R6 2 System Acceptance are as follows e Serial connection Q1 element is commissioned and connected to GCS PC e Q1 Pipe connection Q1 elements are commissioned and connected to polling device NMS 10 MF C2 0 AXC or DCN Adapter C3 0 C4 X Network connection to polling device is operational e Q1 Pipe connection via Q1 Agent Q1 Agent is commissioned and network connection to Q1 Agent is operational e BSC BTS connection Nokia Siemens Networks NetAct Framework has a standard configuration and commissioning has been carried out successfully Q1 elements are commissioned and configured under BTS BSC e Oracle Client is installed and NetAct database server details are configured successfully through Oracle Net Configuration Assistant if acceptance testing is done in NetAct environment 4 4 1 INSTALLATION GCS R6 2 Installation TEST PURPOSE The purpose of this test case is to verify GCS R6 2 installation PRECONDITIONS Oracle Client is installed if GCS NetAct database integration feature will be used DOCUMENTATION GCS User Manual TEST EXECUTION 1 Install GCS R6 2 using the General Communication Service R6 2 msi a b C d e Double click on General Communication Service R6 2 msi
10. In the Scheduled Q1DBtool dialog the Run field is modified to import data from NetAct db using command line c Program Files Nokia Q1 DBTool exe import After specifying the information in the Run field click OK In the Set Account Information dialog retype the administrator password Click OK Create another task using the above mentioned steps but in the Run Field give the command line c Program Files Nokia Q1DBTool exe compact to compacts the database after the import EXPECTED RESULTS S52 ONO PON E 12 13 Logged in to the Node Manager Sever successfully The Scheduled Tasks application opens The Scheduled Task Wizard opens The path of Q1DBTool is set Given path for Q1DBTool is selected The name amp frequency of schedule is set The time of schedule is set The administrator user name and password is provided The dialog opens for the created Scheduled Q1DBtool task The import functionality scheduled task is set The Set Account Information dialog opens and the scheduled task appears in the Scheduled Tasks window The GCS database is automatically updated as specified Each time the GCS database is recreated the previous one is backed up and named dms mbd 001 The compact db task is performed at its scheduled time and the database is compressed 9 BACKUP RESTORE OF GCS DATABASE 9 1 Backup of GCSDatabase TEST PURPOSE The purpose of this test case is to verify back
11. Nokia Siemens Networks ra t General Communication Service R6 2 System Acceptance Test Manual Contents 1 PPM OS staccato sg cated ek ving cee A aOR 3 7am saab nee Rete eat ese RET erating Ret a rome Neon Ene TRENT es ee eee 3 3 PREREQUISITES cusacsssneStacugestiite asme sinus tearatadautioanaomna eaten osetia 3 A INSTALLATION eE r err E tact ats ucran oak tO tical uate oat Le 4 44 GCS REZ IMS tallAN Gs seis ie cota ers eicg soaks Sa aettatic E a RA 4 Ds HUP GRAD EAs ate eat AEE an aauet iad Molo laa tauren entree 5 5 1 Upgrade from GCS R5 x to GCS R612 wesc ciiccescdteciinncuweniecsion 5 5 2 Upgrade from GCS R6 0 to GCS R6 2 ec cccccescseeeeceseesseseeseesscseeeeseees 6 5 3 Upgrade from GCS R6 1 to GCS R6 2 0 ee cccecesescesteescsenescseeeseeseeonens 7 6 Enhancements eaa Saad cred wan cee ear ince A es tedden ae a ei 8 6 1 Enhanced Import logging icuarer de ete aatls tia aie Mena 8 6 2 Windows 7 Database file access privileges check cc ccescsessesseeeeeeees 9 Fo GONNECTIONS orotate ni Oe Ra eee 10 7 1 Serial Port Connection to Q1 NOG oes ccyscaiewusesent esccccctisces eed el Soceiateacs 10 7 2 Network Connection to Q1 NOde cc eccccsscseeescsseeeceseeeeeseesessecseseeseeeees 11 7 3 Q1 Pipe Connection to MF Agent C2 0 uc ccceesesseseeecececeeeceeeaseeeneeaees 12 7 4 Q1 Pipe Connection to QIAGSMIt sa ecsssessesscssdacnsde thes sarstuensisrated eatecnenaastaberzans 13 7 5 Pipe Connection to DON Adapto
12. anned Node is saved in the GCS database without any errors GCS Connection tool is closed successfully QOarhwn 7 6 BSC Connection TEST PURPOSE The purpose of this test case is to verify BSC Connection PRECONDITIONS Nokia Siemens Networks NetAct Framework has a standard configuration and commissioning has been carried out successfully NetAct osscore IP BSC ID ornuser password and Q1 NE address are known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool 2 Create a BSC Connection to Q1 Node In database tab select Connections radio button Click on Add button Enter name to the connection in Name edit box Select BSC Connection from Type drop down list box Enter following parameters information by clicking on Properties button after selecting the each connection definition parameters Dong e Network Parameters HOST NAME and PORT of the NetAct e BSC Parameters USERNAME PASSWORD BSC ID BUS ID e Keep other parameters with default values 3 Save it in the GCS database by clicking Save button 4 Scan the above saved connection for a known range of Q1 addresses a In database tab select Connections radio button b Select the saved connection in steps 2 3 c Click on Scan button d In Scan dialog Enter Q1 Address range in Begin and End edit boxes
13. atabase can be modified 2 Path is specified Restore process should be successful Dbs mdb file should be copied from the specified path to C Documents and Settings All Users Application Data Nokia GCs in XP and 2003 server C ProgramData Application Data Nokia GCs In Vista Windows 2008 server and Windows 7 3 No Path is specified Restore process should be successful Dbs mdb file should be copied from the C Documents and Settings All Users Application Data Nokia GCs in XP and 2003 server C ProgramData Application Data Nokia GCs In Vista Windows 2008 server and Windows 7 4 Able to scan and save the Nodes successfully and Modified or added connections node details should not be present
14. erial Port Connection to Q1 Node In database tab select Connections radio button Click on Add button Enter name to the connection in Name edit box Select Serial Port Connection from Type drop down list box Enter following parameters information by clicking on Properties button after selecting the each connection definition parameters e Serial Port Serial Port is to be given a numeric value 1 or 2 e Baud Rate Baud Rate for the serial port also can be changed this has to be same as the baud rate set for Q1 NE e Keep other parameters with default values 3 Save it in the GCS database by clicking Save button 4 Scan the above saved connection for a known range of Q1 addresses In database tab select Connections radio button Select the saved connection in steps 2 3 Click on Scan button In Scan dialog Enter Q1 Address range in Begin and End edit boxes Click on Start button 5 Save the scanned node if listed in grid box by clicking the button Save Click on Save button in Save Node dialog window Close Scan dialog window by clicking Close button 6 Close GCS Connection Tool using Exit button 9295p oaoop EXPECTED RESULTS Or oP ON 7 2 Connection Tool started successfully Connection is successfully created Connection is successfully saved to the GCS database Node is successfully scanned Node is saved i
15. file access privileges and all the nodes added by another user are visible PRECONDITIONS 1 GCS R 6 2 installed TEST EXECUTION 1 NOP wh ow Launch GCS as an Administrator user Start gt Nokia Siemens Networks gt GCS Connection Tool Add some nodes to the Database Close GCS Connection tool Launch GCS as normal user other than Administrator user Add some nodes to the Database Close GCS connection tool Again launch GCS as Administrator and check for the nodes added by other user are visible to the Administrator user Close GCS connection tool Again launch GCS as normal other than Administrator user and check for the nodes added by Administrator are visible to the current user EXPECTED RESULTS 1 2 GCS launched successfully Both the administrator and normal users should be able to see all the nodes added in the database CONNECTIONS The aim of these test cases is to verify connection and node details can be added to GCS R6 2 database These test cases also verify communication between GCS and Q1 node Serial Port Connection to Q1 Node TEST PURPOSE The purpose of this test case is to verify Serial Port Connection to Q1 Node PRECONDITIONS PC is connected to Q1 Node via serial cable Node s Q1 address is known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool 2 Create a S
16. n the GCS database without any errors GCS Connection tool is closed successfully Network Connection to Q1 Node TEST PURPOSE The purpose of this test case is to verify Network Connection to Q1 node PRECONDITIONS PC is connected to LAN Q1 element is commissioned and network connection to node is operational Node s IP and Q1 address is known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 2 5 6 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool Create a Network Connection to Q1 Node In database tab select Connections radio button Click on Add button Enter name to the connection in Name edit box Select Network Connection from Type drop down list box Enter following parameters information by clicking on Properties button after selecting the each connection definition parameters e Network Parameters Enter the Host Name and Port of the Q1 Node e Keep other parameters with default values Save it in the GCS database by clicking Save button Scan the above saved connection for a known range of Q1 addresses In database tab select Connections radio button Select the saved connection in steps 2 3 Click on Scan button In Scan dialog Enter Q1 Address range in Begin and End edit boxes Click on Start button Save the scanned nodes if listed in grid box by clicking the button Save and clo
17. n to AXC PRECONDITIONS Q1 elements are commissioned and connected to AXC Network connection to AXC is operational and IP address of AXC Q1 Pipe parameters username password and bus number are known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool 2 Create a Nokia Q1 Pipe Connection to Q1 Node a In database tab select Connections radio button b Click on Add button c Enter name to the connection in Name edit box d Select Nokia Q1 Pipe Connection from Type drop down list box e Enter following parameters information by clicking on Properties button after selecting the each connection definition parameters e Network parameters HOST NAME and PORT of the AXC e Q1 Pipe parameters USERNAME PASSWORD BUS NUMBER e Keep other parameters with default values 3 Save it in the GCS database by clicking Save button 4 Scan the above saved connection for a known range of Q1 addresses a In database tab select Connections radio button b Select the saved connection in steps 2 3 c Click on Scan button d In Scan dialog Enter Q1 Address range in Begin and End edit boxes e Click on Start button 5 Save the scanned nodes if listed in grid box a By clicking the button Save button Click on Save button in Save Node dialog window Clo
18. nd password Click Next Check the Open Advanced properties for marker Click Finish In the Scheduled Q1DBtool dialog the Run field is modified to import data from NetAct db using command line C Program Files Nokia QIDBTool exe import logfile lt LogFilePath gt After specifying the information in the Run field click OK In the Set Account Information dialog retype the administrator password Click OK EXPECTED RESULTS NOORWN Logged in to the Node Manager Sever successfully The Scheduled Tasks application opens The Scheduled Task Wizard opens The path of Q1DBTool is set Given path for Q1DBTool is selected The name amp frequency of schedule is set The time of schedule is set 8 The administrator user name and password is provided 9 The dialog opens for the created Scheduled Q1DBtool task 10 The import functionality scheduled task is set 11 The Set Account Information dialog opens and the scheduled task appears in the Scheduled Tasks window 12 If the process import is completed successfully the information message should be logged in Event viewer and the log file generated at lt LogFilePath gt If any failures occurs in the process of import that should be logged into Event viewer and the log file 6 2 Windows 7 Database file access privileges check TEST PURPOSE The purpose of this test case is to verify that the currently logged in user has appropriate database
19. nection Tool 3 Check if the below GCS Services are installed and started successfully in Services List from Control Panel gt Administrative Tools gt Services a General Communication Service b General Communication Service Sync and c General Communication Service Q1DB EXPECTED RESULTS 1 GCS is installed successfully without errors 2 GCS is launched successfully 3 Services are installed and started automatically 5 3 Upgrade from GCS R6 1 to GCS R6 2 TEST PURPOSE The purpose of this test case is to verify upgrade from GCS R6 1 to GCSR R6 2 PRECONDITIONS GCS R6 1 installed DOUMENTATION GCS User Manual TEST EXECUTION 1 Install GCS R6 2 using General Communication Service R6 2 msi a Double click on General Communication Service R6 2 msi available in GCS installable disk b Click Next on General Communication Service R6 2 InstallShield Wizard c Select Complete radio button in setup type dialog of the wizard and click on Next button x Click on Install button in Ready to install the program dialog Click on Finish to complete the installation 2 Sa GCS Connection Tool Start gt Programs gt Nokia Siemens Networks gt GCS Connection Tool 3 Check if the below GCS Services are installed and started successfully in Services List from Control Panel gt Administrative Tools gt Services a General Communication Service b General Communication Service Sync and
20. on d Click on Install button in Ready to install the program dialog e Click on Finish to complete the installation 2 Start GCS Connection Tool Start gt Programs gt Nokia Siemens Networks gt GCS Connection Tool 3 Check if the below GCS Services are installed and started successfully in Services List from Control Panel gt Administrative Tools gt Services a General Communication Service b General Communication Service Sync and c General Communication Service Q1DB EXPECTED RESULTS 1 GCS is installed successfully without errors 2 GCS is launched successfully 3 Services are installed and started automatically 5 2 Upgrade from GCS R6 0 to GCS R6 2 TEST PURPOSE The purpose of this test case is to verify upgrade from GCS R6 0 to GCSR R6 1 PRECONDITIONS GCS R6 0 installed DOUMENTATION GCS User Manual TEST EXECUTION 1 Install GCS R6 2 using General Communication Service R6 2 msi a Double click on General Communication Service R6 2 msi available in GCS installable disk b Click Next on General Communication Service R6 2 InstallShield Wizard c Select Complete radio button in setup type dialog of the wizard and click on Next button d Click on Install button in Ready to install the program dialog e Click on Finish to complete the installation 2 Start GCS Connection Tool Start gt Programs gt Nokia Siemens Networks gt GCS Con
21. one DB is connected and the 2G nodes data is displayed in grid box 2G node details imported without any errors Imported data is verified from GCS access database tab O 0 N D geao N Scheduling Q1DBTool for importing 2G Node details from NetAct TEST PURPOSE The purpose of this test case is to verify scheduling of Q1DBTool for importing 2G Node details from NetAct database to GCS database PRECONDITIONS 1 Oracle Client is installed and NetAct database server details are configured successfully through Oracle Net Configuration Assistant 2 The passwords have been saved for Q1DBTool tool DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Log in the Node Manager Server as an administrator or with equivalent rights 2 In the Node Manager Server select Start gt Programs gt Accessories gt System Tools gt Scheduled Tasks 3 Double click Add Scheduled Task And click Next 4 In the Scheduled Task Wizard Click Browse Find and select the location where you have installed Q1DBTool exe 5 The default installation path is c Program Files Nokia Q1DBTool exe and then Click Next 6 Fill in the name for the import and Set the frequency Click Next 7 Select the values for the start time when this task is to be executed Click Next 8 Fill in the administrator user name and password Click Next 9 Check the Open Advanced properties for marker Click Finish 10 11 12 13
22. r C4 X ce cccceeeeeseeeeeeseeseesceeseeeeeeaees 14 76 7 BSG COMMECIIOMN meee a Soca ds cc cont ial eh A Sone has ke 15 fat BTS Connections msni e torent oad A 16 7 8 Q1 Pipe Connection to ANG ices sis since boree ceil hue hice el beet o cine ant 17 7 9 Telnet Connection to Q1 Node s sesesesesesesesesesesesssssssrsrsrsrsrsrerereereseseseses 18 710 MESECOMMUMIGATOM cocetiec cstenttas n na S ARAD ES 19 8 IMPORT DATA FROM NETACT DATABASE ccccccccscseseesessesseseeseeseseeee 21 8 1 Retrieve 2G Node details from NetAct database eccceceseeeneeees 21 8 2 Scheduling Q1DBTool for importing 2G Node details from NetAct 22 9 BACKUP RESTORE OF GCS DATABASE ccccccccsessescsseseescsseeeseeseeseseens 24 9 1 Backup of GCS Database a ci s5 tees0 ch sceseiees toad sea eareartus eadiabeecendieeaslageens 24 9 2 Restore of GOS Database acc sco ccccceces stitch sedscecacds des taeandarnadeatiaserdavectiscacesies 24 PURPOSE The purpose of this document is to describe the System Acceptance Test cases for General Communication Service GCS R6 2 The test cases are chosen to give as complete picture as possible about the usage of the GCS R6 2 SCOPE This document should be used for System Acceptance Test of General Communication Service GCS R6 2 The main scope of system acceptance test is to verify that General CommunicationJ Service works correctly with Q1 management network elements This document is meant
23. se Scan dialog window by clicking Close button b By Clicking on Save All if want to save all scanned nodes Click on OK in Scan Results Save all dialog window Click on Select All and Save buttons in Scan Results Selection for Database Saving dialog and click on close button to close the window Click on close button in Scan dialog window 6 Close GCS Connection Tool using Exit button EXPECTED RESULTS a e 7 9 Connection Tool started successfully Connection is successfully created Connection is successfully saved to the GCS database Node is successfully scanned Node is saved in the GCS database without any errors GCS Connection tool is closed successfully Telnet Connection to Q1 Node TEST PURPOSE The purpose of this test case is to verify Telnet connection to Q1 Node PRECONDITIONS Q1 Node is connected to Spider port Host name PORT of the Spider Port and Terminal password are known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool 2 Create a Telnet connection to Q1 Node a In database tab select Connections radio button b Click on Add button c Enter name to the connection in Name edit box d Select Telnet connection from Type drop down list box e Enter following parameters information by clicking on Properties
24. se the save and scan dialogs by clicking on Close buttons Close GCS Connection Tool using Exit button eoQa2oo0M Dango EXPECTED RESULTS 1 Connection Tool started successfully MaRWN 7 3 Connection is successfully created Connection is successfully saved to the GCS database Node is successfully scanned Node is saved in the GCS database without any errors GCS Connection tool is closed successfully Q1 Pipe Connection to MF Agent C2 0 TEST PURPOSE The purpose of this test case is to verify Q1 Pipe Connection to MF Agent C2 0 PRECONDITIONS Q1 elements are commissioned and connected to MF C2 0 Network connection to MF C2 0 is operational and IP address NMS 10 MF Q1 Pipe parameters username password and bus number are known DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 2 Start GCS Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool Create a Nokia Q1 Pipe Connection to Q1 Node a In database tab select Connections radio button Click on Add button Enter name to the connection in Name edit box Select Nokia Q1 Pipe Connection from Type drop down list box Enter following parameters information by clicking on Properties button after selecting the each connection definition parameters e Network parameters HOST NAME and PORT of the NMS 10 MF e Q1 Pipe parameters USERNAME PASSWORD BUS NUMBER e
25. ser documentation Open node manager Make connection to node by using node details saved in GCS database For example View active alarms from element Close node manager connection exit manager a 2 3 4 5 EXPECTED RESULTS Node manager is launched Connection to node is established and node data is shown For example Active alarms are shown Connection to node is closed Node manager is closed Ou Ona 8 IMPORT DATA FROM NETACT DATABASE 8 1 Retrieve 2G Node details from NetAct database TEST PURPOSE The purpose of this test case is to verify Retrieve 2G Node details from NetAct database using GCS Connection Tool PRECONDITIONS NetAct database is having nodes with sobriquets DB service should be configured in the net manager of oracle client and connection to NetAct database is working DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 2 3 Launch Connection Tool Start gt Nokia Siemens Networks gt GCS Connection Tool Click on Configure DB button from GCS Connection Tool UI Enter the following information GCS DB Configuration Tool e Enter the Service name userID Password of NetAct oracle database e Select the connection type to configure the respective connection parameters BSC BTS parameters are mandatory and Q1 pipe connection parameters are optional for configuration But if the user wants to connect to the node using Q1 pipe connection while node details are no
26. t present in the MS Access database i e node details are present in oracle database configuring Q1 pipe parameters are mandatory e Enter the OSSPKG CORE IP Address Port User and Password details of the NetAct core server e Enter the port number user and password of Q1 pipe required for GCS to formulate the target string by selecting the Q1 pipe type of connection e Click on Add button to configure the above values into the registry Click on Modify button to modify the configured database parameters if needed e After the changes occur in the dialog restart the application using the GCS Select NetAct from Database drop down list box from GCS Connection Tool Ul Select service name which was saved in step 3 from Service drop down box in NetAct database tab Select ALL if you have only one node manager server installation or select current machine IP for NM IP if your system is having multiple node manager server installation Click on DB Connect button o N 8 Click on Import button to import 2G element connection details which were displayed in grid box 9 Select Access from Database list Check the connections and nodes in Database tab to verify the new data imported EXPECTED RESULTS Connection Tool started successfully GCS DB Configuration Tool is launched Required data is entered NetAct Ul is displayed Service is selected Selection can be d
27. tions radio button Click on Add button Enter name to the connection in Name edit box Select BTS Connection from Type drop down list box Enter following parameters information by clicking on Properties button after selecting the each connection definition parameters e Network Parameters HOST NAME and PORT of the NetAct e BSC Parameters USERNAME PASSWORD BSC ID BUS ID e BTS Parameters BCF ID TRX ID e Keep other parameters with default values 3 Save it in the GCS database by clicking Save button 4 Scan the above saved connection for a known range of Q1 addresses a In database tab select Connections radio button b Select the saved connection in steps 2 3 c Click on Scan button d In Scan dialog Enter Q1 Address range in Begin and End edit boxes e Click on Start button 5 Save the scanned nodes if listed in grid box by clicking the button Save and close the save and scan dialogs by clicking on Close buttons 6 Close GCS Connection Tool using Exit button oQa2oo0M EXPECTED RESULTS Connection Tool started successfully Connection is successfully created Connection is successfully saved to the GCS database Node is successfully scanned Node is saved in the GCS database without any errors GCS Connection tool is closed successfully OF E0 7 8 Q1 Pipe Connection to AXC TEST PURPOSE The purpose of this test case is to verify Q1 Pipe Connectio
28. up of GCS Database PRECONDITIONS GCS R6 2 should be installed Open Command Prompt in Run as Administrator mode DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Run the GCSdbBackup bat file at the command prompt by specifying the destination path 2 Run the GCSdbBackup bat file at the command prompt with out giving the destination path EXPECTED RESULTS 1 Path is specified Backup process should be successful Dbs mdb file should be copied to the specified path from GCS Database Path 2 No Path is specified Backup process should be successful Dbs mdb file should be copied to the C Documents and Settings All Users Application Data Nokia GCs in XP and 2003 server C ProgramData Application Data Nokia GCs In Vista Windows 2008 server and Windows 7 9 2 Restore of GCSDatabase TEST PURPOSE The purpose of this test case is to verify restore of GCS Database PRECONDITIONS GCS R6 2 should be installed Open Command Prompt in Run as Administrator mode DOCUMENTATION GCS online help User Manual TEST EXECUTION 1 Modify GCS database by adding deleting modifying Connection Nodes 2 Run the GCSdbRestore bat file at the command prompt by specifying the destination path 3 Run the GCSdbRestore bat file at the command prompt with out giving the destination path 4 Scan for nodes to verify restored connections by executing test case 9 0 step EXPECTED RESULTS 1 GCS d
Download Pdf Manuals
Related Search