Maxxyz Wing installation note
Contents
1. Out connector of the top module 10 Connect the Ethercon network cable to the Wing Out connector of the top module 11 Attach the desk lamp to the connector labeled Lamp on the back of the top module These steps can also be followed for connecting two modules that are not mounted in a Wing Frame Further it is possible to connect one wing to another wing by going from the Wing Out connector on the bottom module of the first wing to the Wing In connector on the top module of the second wing In no case may the number of modules on a given link exceed four and no cable may exceed 5 meters Maxxyz Wing Installation Note CONNECTIONS AND CONFIGURATION WING MAINS WIRELESS i N N 90 250VAC 50 60 Hz 90 250VAC MAX 2 5A IN OUT Martin ADDRESS _ DIP Switch Address see below for settings Wireless Remote reserved for future use USB In reserved for future use with Maxxyz PC Wing In Ethercon connector Wing Out Ethercon connector USB Out reserved for future use with Maxxyz PC Desk Lamp connector Mains In Co oo N O A Fk WO N Mains Out Connections Connections for either an individual Playback Module or a Wing Frame are simple and similar 1 Connect an Ethercon network cable to the Wing In port on the back of the module If you are using the Wing Frame use the Wing In port on the top module 2 Connect the other end of the Ethercon cable t2. to connect up to sixteen 16 modules or eight fully populated Wing Frames to a Maxxyz console No more than four modules may be connected to any given wing port found on the back of the console and every module must have a unique ID These IDs are set using the DIP switches found on the back of the module The table below shows the appropriate settings for each module Module PIN1 PIN2 PIN3 PIN4 PINS PIN6 1 Off Off Off Off Off Off 2 On Off Off Off Off Off 3 Off On Off Off Off Off 4 On On Off Off Off Off 5 Off Off On Off Off Off 6 On Off On Off Off Off 7 Off On On Off Off Off 8 On On On Off Off Off 9 Off Off Off On Off Off 10 On Off Off On Off Off 11 Off On Off On Off Off 12 On On Off On Off Off 13 Off Off On On Off Off 14 On Off On On Off Off 15 Off On On On Off Off 16 On On On On Off Off A DIP switch pin in the down position is on Software The Maxxyz Playback Module requires connection to a Maxxyz console running version 1 3 78 or higher It is recommended that when the wing is first installed that it be powered before the Maxxyz console is started In this way it is assured that the proper software and drivers will be automatically loaded Maxxyz Wing Installation Note 7 CONTROLS The majority of the functionality of the Playback Module is covered in the Maxxyz User Manual in the chapter Working with Cues under the headin
3. Maxxyz Wing amp Playback Module Installation Note v Martin 2005 Martin Professional A S Denmark All rights reserved No part of this document may be reproduced in any form or by any means without permission in writing from Martin Professional A S Denmark Printed in Denmark P N 35000568 Rev A INTRODUCTION Thank you for selecting the Martin Maxxyz Playback Wing The Maxxyz Playback Wing is an extension to the Maxxyz console that consists of either one or two Maxxyz Playback Module s and a Maxxyz Wing Frame Each Maxxyz Playback Module provides 10 playback faders Each optional Maxxyz Wing Frame accommodates up to two Playback Modules This manual matches the functionality provided in Version 1 3 78 of the Maxxyz software For the latest firmware and software updates documentation and other information about this console please visit www maxxyz com Technical Support For a complete list of Technical Support phone numbers please visit our web site at http www martin com service hotline asp Maxxyz Safety Information This product presents risks of lethal or severe injury due to electric shock Read this Installation Note before powering or installing the console follow the safety precautions listed below and observe all warnings in this manual and printed on the console If you have questions about how to operate the console safely please contact your Martin dealer or call the Martin 24 hour service
4. e e Two spindles for attaching Wing Frame to Maxxyz console SET UP ASSEMBLY There are two different methods of setting up the playback modules one for stand alone use and one for mounting in the Wing Frame In most cases a single module will be used in the stand alone mode while the Wing Frame will be used with two modules Single Playback Module A Maxxyz module ships with protective side plates attached to each side These plates support the faceplate and prevent cosmetic damage to the module Aside from connection to the console the module is ready to use as soon as it s removed from the box Module Use with Wing Frame Remove the Playback Module s and Wing Frame from their packing materials 2 Using a 4mm allen wrench remove the three screws that attach the side plates to each side of the module Insert a module into the ower of the two mounting apertures in the wing frame 4 Gently roll the frame and module onto one side Maxxyz Wing Installation Note 3 5 Align the module with the quarter turn screws illustrated below in the frame and attach the module to the frame by turning the screws one full quarter turn clockwise until they lock 6 Connect the IEC power cable to the Mains In connector 7 Connect the Ethercon network cable to the Wing In connector 8 Repeat steps 2 to 4 to insert a module into the top opening 9 Connect the IEC power cable to the Mains
5. eeded As with any computer never spray the cleaner directly onto the module always spray onto a lint free cloth and wipe clean Important Excessive dust and smoke fluid buildup can degrade performance and cause overheating and damage to the module that is not covered by the warranty 8 Maxxyz Wing Installation Note
6. g Playback Controls However to the left side of the module are 5 LCDs one jog wheel and two buttons that have specific functions LCD Keys The LCD keys on the Playback Module are used for selecting the Bank you are working from To load a bank press the desired key Note that when you press a key to select a bank that bank will then be loaded to the center LCD key and the other LCDs will increment or decrement accordingly Jog Wheel The silver jog wheel is used to scroll up and down the bank selections Rolling the jog wheel up away from you will increment the banks displayed in the LCDs by one Rolling the jog wheel down will decrement the display by one Buttons Above and below the jog wheel are two buttons Pressing the top button will cause the banks displayed in the LCDs to increment by five while pressing the bottom button will cause the LCDs to decrement by five SERVICE The Maxxyz module is designed as a rugged roadworthy device Occasional cleaning is the only service required of the user For any other service related concerns please contact your Martin dealer or visit www martin com Any service not described in this installation note must be carried out by a qualified Martin technician Cleaning The Maxxyz module requires periodic cleaning as does any computer The schedule depends heavily on the operating environment please consult a Martin service technician for recommendations if n
7. hot line at 45 70 200 201 or 1 954 858 1800 e Always ground earth the device electrically e Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection Do not expose the device to rain or moisture e Refer any service operation not described in this manual to a qualified technician e Do not modify the device or install other than genuine Martin parts Power Connection You may need to install a cord cap that fits your supply on the power cable A 3 prong grounding type plug must be installed following the manufacturer s instructions The table below shows some possible pin identification schemes if the pins are not clearly identified or if you have any doubts about proper installation consult a qualified electrician Wire Color Pin Symbol Screw US brown live L yellow or brass blue neutral N silver yellow green ground green Maxxyz Wing Installation Note Included Items Each Maxxyz Playback Module part number 90732100 contains the following items e Playback Module e 6 3 AT fuse installed for use with AC supplies of 200 250 volts e IEC Power cable e IEC Extension cable e Ethercon network cable Desk lamp e USB cable Each Maxxyz Wing Frame part number 90732110 contains the following items e Road case e Wing Frame with attached Ethercon and Power interconnect cables e Desk lamp e Ethercon network cabl
8. o either Wing 1 Wing 2 Wing 3 or Wing 4 on the back of the Maxxyz console It doesn t matter which port you use 3 Connect the IEC cable to the Mains In connector on the back of the module and plug the other end to your mains power supply If you are using the Wing Frame use the Mains In on the top module While it is possible to use the Wing Frame standing separately from the Maxxyz console it is also possible to connect the Wing Frame directly to the Maxxyz console Maxxyz Wing Installation Note 5 4 Remove the top and bottom end caps from either the left or right side of the Wing Frame epee f aaa ONN CULL UIN ity 0 Nag 0 iaa SO y E Remove the top and bottom end caps from the opposite side of the Maxxyz console Place the spindles provided with the Wing Frame into the holes formerly occupied by the end caps in the Wing Frame 7 Ona level surface slide the Wing Frame with attached spindles into the end cap holes on the Maxxyz console It is also possible to connect multiple Wing Frames together in this manner After connecting the Wing Frame to the Maxxyz console it may be convenient to move the monitor bracket from the console to the Wing Frame If you wish to hinge the Maxxyz console up or for transport purposes it may be more convenient to temporarily disconnect and detach the Wing Frame Maxxyz Wing Installation Note Configuration It is possible
Download Pdf Manuals
Related Search