Untitled - Main Light Industries
Contents
1. CAUTION Be careful with your operations With a high voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Important The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Always plug in the power plug least The power plug has to be accessable after installing the device Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth The electric connection repairs and servicing must be carried out by a qualified employee 2 Operating determinations Thi2. 2345 6 Fixture 1 Fixture 2 Fixture 3 Fixture 4 Controller For fixtures with the 6 control channels strobe must be set at the channel 6 only strobe Fixture DMX channels 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 1819 20 21 22 23 24 HAHA AA 12 345612 345 6412345612345 6 Fixture 1 Fixture 2 Fixture 3 Fixture 4 Controller If you want to return to the factory setting press and hold the STEP and TIME button at the same time for 10s If you want delete dedicated the times of the program steps and set the programs no 21 30 to minimum length 1 step press and hold the PROGRAM button and then press the ENTER button Hold both buttons until the reset has run approximately 3 s Set up mode is finished by pressing the ENTER button Setting all LED diodes in this moment is written in EEPROM and will be used as an initial state of the controller Before finishing the adjusting mode check the trigger mode AUTO MUSIC TRIG and the speed mode SLOW MEDIUM FAST for every fixture Calling up a programs Select the desired program between 1 30 CH rn via the PROGRAM UP DOWN buttons The program runs 1 5 s after showing on the PROGRAM DISPLAY The selection CH means that the programs 21 30 will be run through chain The selection rn means that the programs 21 30 will be run randomly selected Programs from 21 to 30 freely programmable chasers Programs from 1 to 10 pre programed for the projectors with the 6 contro
3. DMX Control 24 Pro USER MANUAL Yr Zu NOBE how lighting DMX CONTROL 24 PRO Table of contents 1 Safety instructions 2 sesse BEES ENS EN Ne dee ara Rev N N NN GE WER SE ER We EN wee We beds EViN 4 2 Operating determinations isdie ese dd ek wi Go ed RE Re Ee ene Re N Ee Gee 4 3 Description of the device issie sd Ee UR ER NG Seed Re N Ka de dee ede sd N ke ed WEK nnmnnn 5 d lis talle HOM esse eceseavacnsvenvaninneasetatdeasacandedscadsrutueteneuucuideutiastdebusueudubasceutanvstsvauhemmaceckounye 7 4A Sound Controle Re ed Eb bhas 7 4 2 DMX 512 connection with the projectors ee ee ee ee Re ee ee ee ee ee ee 7 4 3 Fixture addressing si ae Ee EE De ee ER sen lt athcelt aaah eee thay 8 4 4 Connection to the Male RS ES DE EA De Ge nnne 8 Reede EE AE EE duteansvindeseeduesd caueuaudndstvanaineiaveursduancectauasewed 8 6 Technical Specificationi S i s Ne iN dd RE doka AE ed OR ky AE ek EE OER GE RGN Ge n ee EE 10 7 Cleaning and maintenance eeee ees EER RR ER RR AR ER EER REAGEER RR RR R EE REGEER RR RE EE EE 10 Ned EE EE EE EE EE EE EN EE EE OE IE NG Udss 10 CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START UP 1 Safety instructions Every person involved with installation and maintenance of this device have to be qualilfied follow the instructions of this manual
4. ENTER BUTTON Confirming button for programming 21 TIME BUTTON Button for setting of minimum period of last program step in SLOW MEDIUM and FAST modes 22 BLACKOUT BUTTON The Blackout function closes the light output of all connected projectors via the shutter Caution The Blackout key has to be pressed LED is off as soon as a program is called up Otherwise there will not be any light output 23 RANDOM SPEED BUTTON For adjusting the program to random movement 24 FIXTURE SELECT BUTTONS With the fixture select buttons you can choose the desired projector 4 Installation 4 1 Sound control The sound control either works via the Va mono jack socket or the built in microphone If the DMX CONTROL 24 PRO is supposed to work via a soundsignal at the Audio In socket connect the 4 jack socket with the soundsignal of your headphones output or a second adjustable output if existing of your mixer or with the loud speaker output of your amplifier Tip Data Sleeve Ground Caution Never connect the sound input with the DMX output as this will destroy the electric DMX driver 4 2 DMX 512 connection with the projectors ED 120 Ohm Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture wit
5. ded To return the fixture to the program press the respective FIXTURE button and shortly the PROGRAM button The FIXTURE LED will switch off fixture is returned to the program and at the same time the LED diodes of FIXTURES which are chosen from the program will shine To return all fixtures to the program press shortly twice the PROGRAM button Programming Choose one of the freely programmable chasers between 21 and 30 with the PROGRAM UP DOWN buttons Press and hold the PROGRAM button until its LED flashing The PROGRAM DISPLAY shows number of the programmed steps and STEP LED shines Now you can set the values of DMX channels for the current step Press the TIME button and set time on the PROGRAM DISPLAY The TIME value can be between 0 and 5 sec This value is the minimum period of last program step in SLOW and MEDIUM mode waiting on the termination of PAN and TILT movement The value TIME will be immediately be carried out in the FAST mode without waiting on the termination of PAN and TILT movement Creation of the program By pressing ENTER button the current step is written into memory and simultaneously it is replicated into next step The STEP LED shines and the new step is shown You can repeat this procedure as requested The maximum number of programmable steps per program is 32 Modification of the program In order to enter the programming mode press and hold the Program and ENTER button until the Program LED is shini
6. es is as follows Cable EU _ Cable US LP iterational_ Brown Live Light blue i Neutral Yellow Green Earth The earth has to be connected 5 Operation Preparation adjusting mode Press and hold the PROGRAM UP DOWN buttons for 5 seconds and switch on the POWER switch at the same time The PROGRAM STEP and TIME button flashes The PROGRAM DISPLAY shows the current DMX channel and the DMX VALUE DISPLAY shows setting value for this channel Now you can browse through the channels by pressing PROGRAM UP DOWN button and check the function assignments pan tilt and effect assignments strobe blackout to each channel You can assign the channel to the desired button by pressing the PAN TILT COLOR or GOBO button If you wish to assign the next 2 functions gobo rotation and shutter press and hold the COLOR or GOBO button until the LED flashes If you press the STROBE or BLACKOUT button BLACKOUT LED or STROBE LED shines the channel will be subject to the BLACKOUT button or STROBE button in the standard mode NOTE The STROBE BLACKOUT buttons are assigned at the channels 4 and 6 as default If you use the 6 channels fixture you must set strobe only at the channel 6 otherwise the fixture will strobe at the channels 4 and 6 at the same time Default settings suitable for the fixtures with the 4 control channels strobe Fixture DMX channels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1819 20 21 22 23 24 12345612345 61234561
7. h another Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal If you are using the standard controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other DMX outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the DMX CONTROL 24 PRO with the DMX input of the nearest projector Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 ohms resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 3 Fixture addressing Projector addressing Please note that the DMX CONTROL 24 PRO assigns the DMX starting addresses every 6 steps You have to address every projector to the respective starting address Otherwise the channel assignment will not be correct All projectors with the same starting address work synchronically Projector Startingaddress Projector Starting address Projector 1 1 Projector 3 13 Projector 2 7 Projector 4 19 4 4 Connection to the mains Connect the fixture to the mains with the power plug The occupation of the connection cabl
8. l channels DJ Scan 250 XT Programs from 11 to 20 pre programed for the moving heads with the 6 control channels Spot 160 XT Note Only programs 21 30 are used for the options CH and rn Adjusting the program speed The programs run through the selected program step by step with the programmed speed You can adjust the program speed via the SLOW SPEED button MEDIUM SPEED button or FAST SPEED button Jump from one step to another Via the MANUAL TRIG button you have the possibility to jump from one step to another If a program is run and the MANUAL TRIG button is pressed the projector jumps to the next step after finishing the current step The MANUAL TRIG LED shines and the program is stopped If you wish to start the program once more press the AUTO TRIG button or the MUSIC TRIG button Activating the sound control If the sound control is activated the program moves in the bass tact of the music Press the MUSIC TRIG button LED shines and the sound control is activated Strobe function Via the STROBE button you can strobe all fixtures at the same time You can strobe PAN or TILT position too Manual controll of the fixtures If LED diode of some FIXTURE button shines the fixture responds to a joystick movement You can also change the desired value by pressing the FUNCTION button and the UP DOWN buttons on DMX VALUE DISPLAY The function which was changed does not respond to the running program function is exclu
9. ng Now you can modify the program By pressing the STEP button the change is written into memory and the PROGRAM DISPLAY shows the number 9 of current step You can change either step For example if you want to shorten the program set the desired step as last by pressing the STEP button repeatedly The little dot shines behind the number of step If you press the STEP button again the little dot will be switched Off By this procedure you can change all steps Completion of programming Press and hold the ENTER button and let the PROGRAM button loose so that the PROGRAM LED stops flashing The current step is written into memory and the programming mode is finished 6 Technical specifications Power supply 100 125V 200 240V AC 50 60Hz Power consumption 5W Number of control channels 24 Sound control either via Va Jack or built in microphone Sound input Va mono Jack Audio sensitivity 0 3 1V DMX 512 output 3 pin XLR connector Pre programed programs 20 Free chasers 10 with up to 32 steps Dimensions LxWxH 350 x 120 x 78 mm Weight 1kg 7 Cleaning and maintenance DANGER Disconnect from the mains before starting any maintenance work We recommend a frequent cleaning of the device Please use a soft lint free and moistened cloth Never use alcohol or solvents There are no servicable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Sho
10. o input socket 4 DMX output socket Top panel 5 6 7 89 10 11 12 13 14 15 DMX Control Beam position Program 1 09 Manual Trig Function F1 F2 A A Ea Ja x series le 7 18 19 20 21 22 23 24 Fast Speed Random o ms Blackout 16 1 5 DMX VALUE UP DOWN BUTTONS For setting DMX value 6 DMX VALUE DISPLAY Shows current DMX value 7 AUTOTRIG BUTTON If the LED shines the controller is in Auto mode normal operation without sound control 8 MUSICTRIG BUTTON If this LED shines the controller is in Audio mode operation with sound control 9 MANUAL TRIG BUTTON With the Manual Trig button you can jump from one step to another 10 PROGRAM DISPLAY Shows program steps 11 PROGRAM UP DOWN BUTTONS For selecting the program 12 FAST SPEED BUTTON For adjusting the program to fast movement 13 MEDIUM SPEED BUTTON For adjusting the program to medium movement 14 SLOW SPEED BUTTON For adjusting the program to slow movement 15 JOYSTICK With the joystick you can move the light beam manually 16 FUNCTION BUTTONS The buttons F3 and F4 have two functions F3 F5 Colour gobo rotation F4 F6 gobo shutter 17 STROBE BUTTON By pressing the Strobe key all fixtures are being strobed 18 PROGRAM BUTTON Button for programming 19 STEP BUTTON Button for modification of programs 20
11. s device was designed for indoor use only If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature When taking the device into operation please make sure that the housing is closed firmly with all the necessary screws tightened up Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture 4 or dust There should not be any cables lying around You endanger your own and the safety of others Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit electric shock etc 3 Description of the device Rear panel 1 Power switch 1 2 3 4 2 Power supply socket 3 Audi
12. uld you need any spare parts please use genuine parts If the power supply cable of this device will be damaged it has to be replaced by authorized dealers only in order to avoid hazards 8 Appendix We believe you will enjoy your DMX CONTROL 24 PRO We assure you will enjoy this product for years if you follow the instructions given in this manual If you have any questions and comments please do not hesitate to contact us Version 1 0
Download Pdf Manuals
Related Search