Asepti-Cleanse® Dispensing System
Contents
1. WATER RESISTANT SPONGE PAD lt OPTIONAL gt L LES M FOR WALL MOUNTING SCREWS j Ne i y O _M lo g CATCH CHASSIS LE HOLDER NOZZLE COVER LUME SETTING BACK SI T FIGS WATER RESISTA SPONGE PAD OPTIONAL Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 03 OVERVIEW 9 WATER RESISTANT SPONGE PAD COPTIONAL Outlet Cover DECON AHOL Bag DECON HAND Bag Inserted into the Asepti Cleanse Outlet Box 110V Supply j Cc eo m 6V Transformer Transformer Lead to Asepti Cleanse Connection Wall FIG 6 110V Suggested Installation Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 032. Bag are available sterile and non sterile DEC 200 Asepti Cleanse Hands Free Infrared Dispensing System Ordering Asepti Cleanse Dispensing System Description Asepti Cleanse Dispensers for DECON AHOL Operates on 4 D 1 Cell Batteries Asepti Cleanse Dispensers for DECON AHOL or DECON HAND Operates on Battery or 110V transformer plug in to an outlet DECON HAND ag Instant Hand Sanitizer DH 07 DECON HAND Non Sterile Hand Sanitizer Bags for Asepti Cleanse Dispenser 32 ounce fill volume DH 08 DECON HAND Sterile Hand Sanitizer Bags for Asepti Cleanse Dispenser 32 ounce 944 ml fill volume double bag packaged filtered at 0 2 microns and gamma irradiated DECON AHOL WFI Sterile Bag USP 70 filtered and Irradiated Isopropyl Alcohol Order qpescrisioo _ iunicase DECWFI BAG 01 DECON AHOL Sterile 70 USP IPA Bags for Asepti Cleanse Dispenser 32 ounce 944 ml fill volume double bag packaged filtered at 0 2 microns and gamma irradiated Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 03 OVERVIEW 4 Asepti Cleanse Dispensing System Instruction Manual p 2 Soy User Manual 1 Unpacking The dispensers are shipped with mounting screws and plastic anchors for mounting on drillable surfaces The package also contains two double sided adhesive pads as an alternate mounting means F
3. amongst other things in damage to the dispenser and or leakage which in turn could create conditions leading to personal injury In no event shall the vendor be liable for any damage or injury caused by any solutions lotions solutions or other liquids used in the dispenser Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 Toll Free 888 4 STERILE 888 478 3745 Tel 610 644 8335 Fax 610 644 8336 e mail vai sterile com Website http www sterile com Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 03 OVERVIEW 7 OPEN COVER LA I SEA FIG 1 OPENING COVER AI TN Lie TAPE 2 oft O O oR E TARE 7 H MUST BE GREATER THAN 127 H ail VLLLLILILLLLLLL LLL LLL LLL LLL LLL LLL LLL LLL LLL FIG4 POSITIUN TAPE BAC F CHASSIS FIGs 12 ABOVE THE COUNTER LEE ALK Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 03 OVERVIEW 8
4. end of hose into the slot of the nozzle holder Fig 3 Note as cover is closing the unit will cycle but solution will not dispense unless cover is fully closed Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 03 OVERVIEW 6 8 Close Cover Once both the batteries and solution are installed close the cover Make sure that the nozzle seal gasket does not block tip of the nozzle otherwise the cover should be reopened and the position of the nozzle should be adjusted Now place your hand under the solution dispenser the solution will be pumped out on your hand 9 Re opening the cover without discharging solution Use your index finger to approach the latch release bar Fig 3 from the side of the unit Pull down release bar while keeping hand away from the centrally located hand sensing elements Releasing the latch in this manner will avoid needless discharge of solution Warranty This touch free solution dispenser is warranted against defective materials and workmanship for a period of ninety 90 days from the date of the original purchase Equipment covered by this warranty will be repaired or replaced in the United States and Canada WITHOUT CHARGE except for shipping and handling by our Factory Service Center When returning equipment for warranty service the shipping charges must be pre paid and a copy of your receipt mus
5. OVERVIEW 1 Asepti Cleanse DISPENSING SYSTEM Hands Free Auto Eye Sterile Solution For Use with Veltek Associates Inc s DECON AHOL WFI Bag and DECON HAND Zag Products Val Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 03 mn OVERVIEW 2 Asepti Cleanse Dispensing System For use with VAI s DECON AHOL WFI or DECON HAND Zag Alcohol Products Veltek Associates Inc is an EPA and an FDA Registered Manufacturing Operation Asepti Cleanse has been designed by VAI as the most advanced Infrared Sensor Dispensing System available in the pharmaceutical and biotech industry The dispensing unit is designed to meet the requirements of cGMP clean room operations More importantly the dispensers utilize a specially designed package of the premiere brand name DECON AHOL WFI Sterile and DECON HAND Sterile Features The Asepti Cleanse Dispensing System is a sealed unit that protects the coated internal electronics The Asepti Cleanse Dispensing System is photo eye operated Just place your hand underneath and it dispenses a pre measured dose to the hand without contact of the person to the unit The Asepti Cleanse Dispensing System can be adjusted to dispense 1 3 or 5 ml s The Asepti Cleanse Dispensing System is designed in a dual power configuration of power supply The Asepti Cleanse Dispensi
6. d align with the holes of the chassis Do not remove the protective paper from backside of pad Screw the dispenser with the pad onto the wall Close the cover Note somewhat more force is needed in order to overcome the resistance from the pad then open it to see if the edge of the cover is properly sealed amon mA p 4 Battery Installation Four D size professional alkaline batteries are required to power the unit The unit contains two battery compartments one on each side of the dispenser Install two batteries in each compartment Load the space toward the back of the compartment first Place the flat negative end of the battery against the spring and depress the spring until the positive end can be moved in the place Each battery must have the negative end in contact with the spring Load the remaining batteries in a similar fashion 5 Electrical Wiring to 110V It is advisable to check your local codes prior to installation of this unit The power requirement for the dispenser is 6 volts DC unregulated with a minimum of 700ma output the connector is 5 5 mm outer diameter and a 2 5 mm inner with a 9 10 mm length Center pin is positive as is the standard Suggested installation requires A The installation of 110V power line to the desired location B At the introduction site an electrical outlet box should be installed to house the Asepti Cleanse transformer c The size of the transformer may slightly vary due to the
7. model supplied Measure the transformer and assure the electrical outlet box it slightly larger than the transformer D Connect the 110V to an outlet or assure you are using a transformer with direct 110V feed connections E Connect the transformer to the outlet unless the transformer is connected directly to the 110V feed line F Replace the outlet cover with a pre drilled hole for the transformer line to go through to the dispenser G Connect the transformer line to the Asepti Cleanse and then mount the unit to the wall H Contact VAI technical support with any questions at 1 888 478 3745 610 983 4949 6 Volume Setting see Fig 3 The dispenser ejects approximately 1c c of solution per cycle A switch with three setting positions 1 2 3 allows the selection of one three or five cycles per actuation see right view of Fig 3 As shipped the switch is set for one cycle operation Do not load solution at this time Now close the cover to test the unit Note the unit will activate as you close the cover With cover closed place your hand under the bottom of the unit The unit should now activate for one three or five cycles in accordance with the volume switch setting 7 DECON HAND and DECON AHOL Liquid Bag Installation Open the dispenser cover Remove perforated portion of box to expose hose attachment Place the solution container in solution compartment with hose forward Pull hose attachment out and insert flange at the nozzle
8. ng System DEC 200 unit can be powered by 4D cell batteries 4D cell last over 1 year or connected directly to 110V in the same unit In the electrically mounted installation one has the backup of the battery power if a failure in the power line occurs due to abnormal situation Simply it has it s own backup system The Asepti Cleanse Dispensing System mounts directly on glass or walls The Asepti Cleanse System is water resistant in design The Asepti Cleanse Dispensing System uses the brand name DECON AHOL WFI Sterile and DECON HAND Sterile products that have been used in the pharmaceutical and biotechnology industry for over 10 years Bags are removed and replaced in seconds The DECON AHOL WFI Sterile and DECON HAND Sterile products are filtered at 0 2 microns into the Asepti Cleanse bag system Each bag is double bag packaged and subsequently terminally sterilized via gamma irradiation The DECON AHOL WFI Sterile and DECON HAND Sterile products have been completely validated for assay and sterility per AAMI USP and cGMP requirements The Asepti Cleanse Dispensing System is small measuring 12 L x 5 W x 5 H and has a keyless opening and closing of the unit Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 03 OVERVIEW 3 Stand not available unit mounts directly to wall DECON AHOL Bag and DECON HAND
9. or installations where water protection is desired a sponge mounting gasket is available upon request Remove the dispenser from the box with the mounting hardware and pads 2 Open cover Fig 1 shows the location of the latch bar at the bottom of the unit Place your index finger behind the bar and pull outward to release the cover latch Lift the top of the cover upward and open cover to full open position 3 Installation CAUTION The bottom of the dispenser should be mounted at least 12 30cm above the horizontal surface of the sink or counter top Fig 2 3 1 Non Water Proof unit 3 1 1 gt A Installing unit with adhesive pads Tape 1 150x75mm about 6 3 Tape 2 130x75mm about 5x3 see Fig 4 Keep the cover fully open Clean the bottom of the chassis and surface where dispenser is to be mounted with isopropyl alcohol Remove protective paper from one side of each adhesive pad and press the pads in the place at the locations indicated in Fig 4 Remove protective covers from the back surface of each pad Mount unit at the desired location by pressing unit against mounting surface 3 1 2 Installing unit with screws A B Keep the cover fully open Place the unit against the wall at the desired location Using the five holes of the unit as a template and marking the wall with pencil Use 11 64 4 4mm drill bit to drill holes Insert anchors into the holes Screw the dispen
10. ser on wall 3 2 Water Protection Fig 3 3 2 1 Installing unit with a sponge pad Fig 5 A B Keep the cover fully open Remove the front side paper from water seal sponge pad Carefully put dispenser chassis on the sponge pad and make sure that the U shape edge of the sponge pad conforms to the edge of the chassis Press the sponge pad on unit and make sure it is properly adhered to the chassis Clean the bottom of the chassis and surface where dispenser is to be mounted with isopropyl alcohol Remove the backside paper and carefully press the dispenser on the clean mounting surface Close the cover Note somewhat more force is needed in order to overcome the resistance from the sponge pad and then open it to see if the edge of the cover is properly sealed Veltek Associates Inc 15 Lee Boulevard Malvern PA 19355 1234 Tel 610 644 8335 Fax 610 644 8336 E mail vai sterile com ASP CLS 01 Rev 12 18 03 OVERVIEW 5 3 2 2 Installing unit with a sponge pad and screws A Keep the cover fully open B Place the unit against the wall at the desired location Using pencil mark the position of the five mounting holes on the wall Use 11 64 4 4mm drill bit to drill holes Insert anchors into the holes Remove the front side paper from the water seal pad Carefully put dispenser chassis on the pad and make sure that the U shape edge of the sponge pad matches the edge of the chassis and the five holes on the pa
11. t be enclosed This warranty covers all defects incurred from normal use of the equipment and does not apply in the following cases a Loss of damage to the equipment due to abuse mishandling accident or failure to follow operating instructions If the equipment is defective as a result of leaking batteries c If the equipment has been serviced or modified by someone other than our authorized agents THE AFOREMENTIONED IS IN LIEU OF ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR ANY PARTICULAR PURPOSE IN NO EVENT SHALL THE VENDOR BE LIABLE FOR CONSEQUENTIAL INCIDENTAL INDIRECT OR SPECIAL DAMAGES OR LIABILITY TRANSPORTATION INSTALLATION OR SUBSTITUTION COSTS DELAYS OR FOR ANY OTHER DAMAGES COSTS OR EXPENSES INCURRED IRRESPECTIVE OF HOW THEY OCCUR THIS WARRANTY SHALL NOT EXTEND TO ANY OTHER PERSON OTHER THAN THE ORIGINAL PUCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT This warranty gives you specific legal rights and you may also have other rights which may vary from state to state This warranty is given with respect to equipment purchased in the United States This warranty is for the touch free solution dispenser only and excludes any representation or warranty with regard to any solution lotion solution or other liquid used in the dispenser Use of improperly formulated solutions lotions solutions or other liquids could result
Download Pdf Manuals
Related Search