Audiovox Prestige P-105 User's Manual
Contents
1. 7 Re assemble the dash using the reverse of the disassembly procedure 5 TYPICAL INSTALLATION FOR CHRYSLER Figure 2 pue p 995 NILNNOIN YS 1ISAYHO SMAYOS wwo dO SAYVMGYVH ONILNNOW ONILSIXA SSAINYVH 9094 SSSNYVH 553 5 HSVd Y3LNO ATOIHSA H gt S KON 9 1104 SNOT 5 5 FTOIHSA v ALI IANNADNV14 137505 VNNALNV 418V9 VO YOLOANNOO dydS dMd Nid tL HSVd A TOIHSA VNNSALNV YOLOANNOO YASNVHO GO MAIA dvad 8xOVERSAMPLING i S ISO REPEAT T SCAN LOUD Ena 0257 6 REPEAT SHUFFLE Figure 3 TAB 2 8xOVERSAMPLING SS ee T EM 1 6 DISC amp REPEAT SHUFFLE GD Figure 4 ISC PAUSE REPEAT SHUFFLE mD GD O ODO Figure 5 2001 Audiovox Electronics Corp Hauppauge NY 11788 iN For Customer Service Visit Our Website At Www audiovox com Product Information Photos FAQ s Owner s Manuals 128 5914A2. by AUDIOVOX INSTALLATION MANUAL P 105 AM FM MPX RADIO WITH COMPACT DISC PLAYER CD CHANGER CONTROLS AND QUARTZ CLOCK ISE DIGITAL AUDIO INSTALLATION INSTRUCTIONS This unit is designed for installation GM and Chrysler cars trucks and vans with a 1 1 2 DIN radio opening In some cases a special installation kit will be required to mount the radio to the dashboard These kits are available at electronics supply stores and car stereo specialty shops Always check the kit application before purchasing to make sure the kit works with your vehicle If you need a kit but cannot it available call our toll free HELP line at 1 800 645 4994 PRE INSTALLATION CONSIDERATIONS IMPORTANT Disconnect the ground cable from the negative terminal of the battery a Dash Disassembly NOTE Locations and types of fasteners will vary depending on the make and model of the vehicle Carefully check the dash for all fasteners that may require removal in order to remove the factory radio from the sub dash 1 Remove the screws securing the upper and or lower portion of the dash panel 2 Remove the screws above the instrument cluster and all screws from the trim panel that may surround the factory radio Remove the ashtray and open the glove box to see if there are any screws that need to be removed from the dash panel Do not discard any screws NOTE The gear shifter may need to be in low gear to allow for dash panel removal 4
3. Gently unclip and remove the dash panel b Removing the Factory Radio 1 Remove any hardware securing the factory radio assembly to the sub dash Do not discard any hardware 2 Disconnect the wiring and antenna cable from the factory radio c Removing the Factory Radio Brackets If Applicable 1 Remove all nuts that secure the original factory brackets to the radio 2 Remove and retain the original mounting brackets from the factory radio NOTE Not allradios have removable mounting brackets For GM radios with non removable brackets use the two enclosed These will satisfy most 1993 and up GM radio mounting applications If this is not the case it will be necessary to purchase a special installation kit Please consult your local car stereo installation shop or consumer electronics store d Check the dashboard opening size by measuring the height and width If the opening is not large enough carefully cut or file as necessary until the opening slightly exceeds the radio size Check that there will be sufficient space behind the dashboard for the radio chassis NOTE After confirming fit place the P 105 aside and proceed with the wiring instructions USING A WIRING ADAPTER The easiest wiring method to connect the P 105 to the vehicle is to buy a wire harness adapter from your dealer a car stereo installation shop or an electronics store If you use a wiring adapter all wires can be connected to your P 105 even before your old radio
4. the enclosed brackets 6 if the original factory brackets are not removable Additionally four brass spacers bave been provided to raise the bracket height as required Simply place the spacer on the quickie bolt and secure the mounting bracket Some vehicle applications incorporate a rear mounting support Remove the rubber rear bushing from the factory radio Match the rear quickie bolt on the P 105 radio to the rear factory radio bolt location and snap the long quickie bolt Item 3 into place Thread the rubber rear bushing from the factory radio onto the P 105 long quickie bolt 4 Plug supplied wire harness 1 into the mating socket on the rear of the P 105 Installation 1 Connect the wiring harness from the radio to the vehicle side radio harness 2 Plug the factory antenna cable into the antenna socket on the radio NOTE GM vehicles 1992 and up will require an antenna adapter cable to convert the vehicle mini connector to a standard 3 connector Antenna adapter cables are available at car stereo speciality shops If a compatible CD changer 15 to be used with this radio connect the cable from the changer to the 8 mating socket on the radio If an external amplifier will be used for the rear speakers connect the low level output RCA leads from the radio to the low level inputs on the amplifier Reconnect the battery and perform a brief functional test of the radio to verify proper performance
5. 344 which is furnished with the radio 1 Select two of the four mounting tabs provided and match the radio mounting style of the vehicle as shown in Figures 3 4 and 5 NOTE The tab number is stamped the bottom of the tab 2 Attach the mounting tabs to the radio chassis with the four small Phillios head screws provided 9 3 Attach the 14 pin connector from the harness to the radio 4 Plug the antenna cable into the antenna socket on the radio Installation 1 Attach the ring lug on the ground wire black from the radio side harness along with the vehicle side grounding strap to the rear of the radio chassis using the short quickie bolt 2 and the flange nut 4 provided 2 Connect the mating side of the harness to the vehicle side wiring harness 3 Connect the vehicle antenna cable to the radio antenna connector 4 compatible CD changer is to be used with this radio connect the cable from the changer to the 8 pin mating socket on the radio If an external amplifier will be used for the rear speakers connect the low level output RCA leads from the radio to the low level inputs on the amplifier 5 Reconnect the battery and perform a brief functional test of the radio to verify proper performance 6 After verification turn off the ignition switch and install the radio into the sub dash of the vehicle using either two 10mm hex head screws not provided or use the existing factory hardware
6. After verification turn off the ignition switch and fasten the radio to the sub dash using the mounting hardware previously removed from the factory radio Re assemble the dash using the reverse of the disassembly procedure WIRING DIAGRAM TYPICAL INSTALLATION FOR GM Figure 1 SS9V1d Z lt 9 6 c INALI 110g IMNO LUYOHS ONILLNNOIN 5 paijddns 24 WALI 1109 3 21 0 L 5 5 01 ATSaLVYVdSaS SSVWHOUNd SSSNYVH WD EE SSANUVH 9 NILI 6307 19 2 oN Kook A OldVd SOl d ACIS ATOIHSA JTOIHSA 4 7 INN AdOLOVA e WALI N 5 9 SIMDINO N SNOT N R 137205 S319V9 VOU do 55 INI W9 Nid v4 YOLOANNOO GHYVGNVLS OL YOLOANNOOD ININ 5 ATOIHSA AHL LYAANO9 OLATEV9S 1 VNNALNV NV SYINOAY 2661 SATOIHSA WS ALON HSVd A TOIHSA YOLOANNOO YASDNVHO MAIA Avay A TYPICAL CHRYSLER APPLICATION See Figure 2 Radio Preparation NOTE For Chrysler car installations use the Chrysler Hardware Kit Part Number 150 1
7. is removed from the car Connecting the Wires Splice crimp or solder the wires from the Audiovox P 105 radio connector to the wiring adapter Match the wires according to the function vs color code relationship expressed in the following table and the wiring adapter instructions Attach Wires to Radio See Figures 1 and 2 a After splicing the wiring adapter to the radio connector attach the connector to the back of the radio b Attach an antenna extender cable not supplied and antenna adapter if needed NOTE The Dimmer function may not work in conjunction with some Chrysler vehicle models In this case leave the Dimmer wire disconnected Radio backlighting will illuminate when radio power is on Install Wiring Inside the Car See Figures 1 and 2 a Connect wiring adapter to the car s existing wiring harness b Connect an antenna extender cable not supplied to car antenna lead if needed WIRING COLOR CODES hed TYPICAL GM APPLICATION See Figure 1 Radio Preparation NOTE For GM car installations use the GM Hardware Kit Part Number 150 1343 which is furnished with the radio 1 Match quickie locations on the 105 radio to the factory radio locations and snap the short quickie bolts 2 into the appropriate locations Attach the original factory brackets or those from the radio mounting kit if required to the P 105 radio using the supplied flange nuts 4 or use
Download Pdf Manuals
Related Search