Premier Mounts CTM-MS2 flat panel wall mount
Contents
1. cD Installing the Mounting Brackets con d Attaching the Mounting Brackets to the Flat Panel This section presumes that you have read and understood these sections Selecting the Proper Mounting Hardware Universal Washer Installation Universal Spacer Installation Place your flat panel screen side down on a soft flat surface Identify the number and location of the thread inserts on the back of your flat panel Aligning the holes on each mounting bracket with the thread inserts on the back of your flat panel Secure each mounting bracket to your flat panel by inserting a minimum of two 2 screws per bracket A Do not overtighten the mounting hardware Proceed to the Mounting the Flat Panel below Mounting the Flat Panel Attaching the Flat Panel to the Wall Plate A This section requires two people Do not release ae flat panel until you are certain that top and bottom hooks of both mounting brackets are securely seated on the upper and lower mounting rails of the wall panel Raise the flat panel past the top and bottom mounting rails on the wall panel Slide the flat panel down slowly keeping it close to the wall Engage the top and bottom mounting brackets to the rails of the wall plate Page 10 Visit the Premier Mounts website at http www premiermounts com CTM MS2 Installation Instructions C2. Instructions Visit the Premier Mounts website at http www premiermounts com Page 11 gt 4 22 CTM MS2 Locking Safety Screw Installation The locking safety screws keep the flat panel from being accidently dislodged from the CTM MS2 Thread an M6 x 30mm locking safety screw at the bottom of one of the mounting brackets Use a Phillips head screwdriver to tighten the locking safety screw Repeat steps 1 and 2 for the other locking safety screw M6 x 30mm Locking Safety Screw 1 per Bracket ocoooocoocoooooocoooocooooooocoog CTAB 7 A Do not overtighten the locking safety screws Proceed to the Installing the Mounting Bracket below Tilt Adjustment Adjusting the Flat Panel Friction Tilt Angle Place one hand at the center top edge of the flat panel Place the other hand on the center bottom edge of the flat panel Using the upper hand gently pull the top of the flat panel towards you while the lower hand gently pushes the bottom of the flat panel away from you Adjusting the Flat Panel to the Original Position Place one hand at the center top edge of the flat panel Place the other hand on the center bottom edge of the flat panel Using the upper hand gently push the top of the flat panel towards the wall while the lower hand gently pulls the bottom of the flat panel away from the wall Page 12 Visit the Premier Mounts website at http www premi
3. when mounting the flat panel Locking Safety Screws Prevent the flat panel from being removed or dislodged from the wall plate Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 5 b a 24 CTM MS2 Installing the Wall Plate Introduction Directional Mounting Arrow The Directional Mounting Arrow stamped into the CTM MS2 wall plate indicates which edge is the top Visual Centering Diamond The Visual Centering Diamond will guide you in determing the screen placement on the wall Mounting Safety Two people are recommended to install the wall plate You must secure the wall plate to two 2 wall studs with six 6 lag bolts 3 lag bolts for each stud found Use a stud finder to determine the exact center of wall studs in the vicinity of the wall plate Use a pencil to mark the exact center of each of the wall studs Two people are recommended for this step one person to level the wall plate and another person to mark the wall stud location Place the wall plate against the wall in the desired viewing location Adjust the wall plate to align the mount slots in the wall plate with the center of the wall studs Level the wall plate Use a pencil to mark the upper r
4. BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR INANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel If mounting to wall studs or ceiling studs make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs Use of an edge to edge stud finder is recommended A It is recommended that a maximum of plaster board be used when mounting to wooden studs Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure tha
5. SULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Premier Mounts intends to make this manual accurate and c
6. TM MS2 24 Safety Knurl Knob Installation If you chose not to install the safety knurl knobs and instead chose to use the Panelock skip this section and proceed to the Panelock Installation section below The Panelock is a theft deterent device It comes with security hardware that requires a special tool that is used to install and remove the security head screws The safety knurl knobs keep the flat panel from being accidently dislodged from the CTM MS2 Fully extend the flat panel away from the wall Install and tighten a safety knurl knob at the top of one of the mounting brackets Repeat steps 1 and 2 for the other safety knurl knob Safety Knurl Knob 1 per Bracket Panelock Installation If the safety knurl knobs were previously installed they must be removed prior to installing the Panelock hardware Slide the Panelock onto the top mounting rail placing the Panelock to the outside edge of the flat panel bracket i A Panelock f Be sure that the Panelock is facing in the same Hook direction as shown in the illustration to the right Insert and tighten one 1 M6 x 12mm screw to attach the Panelock to the flat panel bracket M6 x 12mm Repeat and to attach the remaining Gr n Head 3S Panelock Proceed to Tilt Adjustment on page 12 Security Head Wrench Panelock Hook Security Head Wrench Installation
7. cD PREMIER Cag MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS NORTH AMERICA EUROPE 3130 East Miraloma Avenue Unit 3 The Moorings Business Park USA and Canada Phone 1 800 368 9700 oo eae Fax 1 800 832 4888 Other Locations Fax 44 0 24 7664 4165 Phone 001 714 632 7100 Fax 001 714 632 1044 cus 9531 000 311 08 LISTED 7 D a O 4o 0p N Weight SUN lenis tess te erties te sae a e a E E a eadaees eanerieehs 2 WalMING Staleme S cs S NS S ASS 2 INStallAtON Too ccsesssceettensvedetseeiscaseteenyescecuaenvasiadseeiscasdadtayyaceiaeeevicaslageyscashigen S A AN 3 Pans ISU sscteserets caventecaahagaceactauausee tes vuuteceeusuuieaeeadtqiesdeetay AA 3 Mounting HardWare saa E Soa Hac eocdundaditews pundit da a O Maduecaueaaiaele 4 Nylon Spacers and Flat Washo assen a a ateaeadducecaaheoadenens AS 4 Foa ES ia N E O ONON ONRAN NO een races 5 Installing De Wal Platerak aa a a O N A 6 OOUE E E E a a N E 6 Installing the Mounting Bracko sanonnan n O E N 8 Selecting the Mounting Hardware anrsnnisni in A 8 Griplate Washer InstalatiOMicispnriinienininipaaa E aa aE a aa 9 Nylon Spacer IMS tallations sse E A R 9 Attaching the Mounting Brackets to the Flat Panel eeeeesseessserseesrrererireisererrreerinnnsseesrneessinussattrseeereaeas 10 Mounting the Flat Pamela es cad cccet tiasicselevinscvaicetannscdeans ehddvaed N E O ne aaaadiorseheeeeee eee 10 Attachin
8. er Mounts Universal Washers are designed to accommodate the various M4 M5 M6 and M8 hole sizes required by flat panels Do not place excessive pressure on the back of the flat panel as this may damage the flat panel The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown Does the flat panel have Recessed mount points Uneven mount points Acurved back Any obstruction near the mount point If Yes you must install Universal Spacers Remove the mounting brackets Universal Washers and mounting screws from the back of the flat panel Proceed to the Universal Spacer Installation below If No skip to the Attaching the Mounting Bracket to the Flat Panel on page 10 Universal Spacer Installation Premier Mounts Universal Spacers allow you to attach the mounting bracket to flat panels which have recessed or uneven mount points Each Universal Spacer adds to the distance between the mounting bracket and the flat panel The Universal Spacers must be stacked and oriented as shown The Universal Spacers must only be installed between the mounting bracket and the flat panel The Universal Spacers will fit M4 M5 M6 and M8 screw sizes Proceed to the Attaching the Mounting Bracket to the Flat Panel section Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 9
9. ermounts com Installation Instructions CTM MS2 Technical Specifications All measurements are in inches millimeters 32 25 819 15 26 59 675 491 19 09 484 99 11 09 281 791 a 4 e t 0 fe gt o o O Cc gt z 0 19 00 482 601 f 21 00 533 401 H C 7 x gt C gt rE E 16 12 409 57 32 25 819 15 19 00 482 60 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 13 gt 4 on CTM MS2 PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RE
10. g the Flat Panel to the Wall Plate 0 2 00 cccesecceceseccceeeeeneeeceeenanteceeeneataeeeeenanaeceeeneaseeeeesnaaeeeeenees 10 safety Knud Knob Installationirns2 seb vss vince eadiecls T a wean evdadele dane 11 Locking Safety Screw Installation c isisscictcissccctcesdenccoeaniectanciasedesass adedacmeaadaescancrasehcdettagdeteamuadacncnaaasencee 11 TIME AGJUSUMON eesse aN O nas ceeeaenedeeseeen senna senshi ereedeneereanaiee 11 Technical Specifications cccccaccccscessaeacand scactecnaaneacnch a eE EEA aa E a Era 12 E I O A A I A E A T A E A E E I EE P E I E E T 13 Weight Limit THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF Maximum Flat Panel Weight 1 60 bs a THE FLAT PANEL IF NOT THE WALL STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE STOP PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED
11. ight mounting location along the center of the wall stud Drill a pilot hole in the center of the upper right mark using a 1 4 drill bit and power drill A Only use a drill bit when drilling pilot holes Page 6 Visit the Premier Mounts website at http www premiermounts com Installation Instructions b 4 CTM MS2 D2 Installing the Wall Plate cont d Place the wall plate against the wall and align it with the pilot hole Insert one 1 5 4 x 3 lag bolt and one 1 6 washer into the upper right pilot hole Use a socket wrench and a 2 socket to tighten the lag bolt A Do not overtighten the lag bolt Level the wall plate Use a pencil to mark the remaining five 5 mounting locations along the center of each wall stud Two people are recommended for this step one person to level the wall plate and another person to drill the pilot holes Drill a pilot hole in the center of each of the marks with a power drill and a drill bit A Only use 74 drill bit when drilling the pilot holes Insert one 1 x 3 lag bolt and one 1 he washer into each pilot hole Tighten all lag bolts using a socket wrench and 1 socket Do not overtighten the lag bolts when attaching the mount to the wall Improper installation may result in personal injury or property damage Proceed to the Installing the Mounting Bracket on page 8 Installation Instructions Visi
12. omplete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2011 Page 14 Visit the Premier Mounts website at http www premiermounts com Installation Instructions
13. rew Qty 6 M4 x 25mm Screw Qty 6 M6 x 45mm Screw Qty 6 M4 x 30mm Screw Qty 6 M8 x 16mm Screw Qty 6 M5 x 16mm Screw Qty 6 com ca u 0 a comme M8 x 25mm Screw Qty 6 w CE C M5 x 25mm Screw Qty 6 M8 x 30mm Screw Qty 6 e Ca M5 x 30mm Screw Qty 6 a M8 x 45mm Screw M6 x 16mm Screw Qty 6 Qty 6 M6 x 25mm Screw M8 x 70mm Screw Qty 6 Qty 4 Page 4 Visit the Premier Mounts website at http www premiermounts com Installation Instructions CTM MS2 es Features Mounting Slots Allow for a variety of stud configurations and lateral adjustments when installing the wall plate Cable Electrical Cut Out Allows for easy cable access and power distribution installations Directional Mounting Arrow Lets you know which edge is the top Safety Knurl Knobs Prevent the flat panel from being removed or dislodged from the wall plate i Universal Spacers Premier Mount s uniquely designed spacers that fit multiple screw sizes Visual Centering Diamond The visual centering diamond will guide you in determing the screen placement on the wall Mounting Rails Allow lateral adjustments
14. t is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 CTM MS2 24 Installation Tools The following tools may be required dependent upon your particular installation These tools are not provided by Premier Mounts but you can purchase them at your local hardware store Electronic Stud Finder Protective Eyewear Portable Drill Ya Drill Bit g gt a Socket Wrench 2 Socket Phillips Head Screwdriver Parts List Your Premier Mounts product is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts at 1 800 368 9700 CTM MS2 Tilting Wall Mount Assembly Components Mounting Bracket Thread Depth Indicator Qty 2 Supplied Griplate Washer M6 Safety Knurl Knob Qty 6 Qty 2 M6 x 12mm Security Head Screw Qty 2 She x 3 Lag Bolt 5 16 Flat Washer i i Wooden Studs Only Qty 6 Qty 6 Screw Qty 2 rien e Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 3 b a eZ CTM MS2 Parts List cont d Mounting Hardware M4 x 16mm Screw Qty 6 M6 x 30mm Sc
15. t the Premier Mounts website at http www premiermounts com Page 7 b 4 24 CTM MS2 Installing the Mounting Brackets Selecting the Mounting Hardware lnsert a small straw or toothpick into the threaded inserts found on the back of the flat panel Usea pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert Marking the 1 8 If the screw you selected is longer than the 1 8 Allowance allowance mark on the small straw or toothpick as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark Marking the Depth Threaded Insert Test each size of the screws provided The correct screws should thread easily into the mounting point and not pull out when tension is applied Proceed to the Griplate Installation section Small Straw epth Plus 1 8 Allowance all Str Depth Plus 1 8 Allowance or Toothpick ark or Toothpick Mark Page 8 Visit the Premier Mounts website at http www premiermounts com Installation Instructions CTM MS2 22 Installing the Mounting Brackets contd Griplate Installation Premi
Download Pdf Manuals
Related Search