USER`S MANUAL
Contents
1. OL OL Pedal Arm Bushing 42 Rear Pedal Arm Bushing 11 4 Extra parts may be included ASSEMBLY Assembly requires two people Place all parts of the PROFORM 485E in a cleared area and remove the packing materials Do not dispose of the packing materials until assembly is completed Assembly requires a phillips screwdriver E mallet i 1 Feed the console wire down through the Upright 3 as shown While another person holds the Upright near the Frame 1 tie the console wire and the Sensor Wire 25 together as shown in drawing 1a Next connect the console wire to the Sensor Wire Gently pull the Resistance Cable 26 and the console wire out of the top of the Upright 3 until there is no slack between the Upright and the Frame 1 Slide the Upright 3 onto the welded bolts on the Frame 1 Be careful to avoid pinching the Resistance Cable 26 and the Sensor Wire 25 Tighten a 3 8 Nylon Locknut 29 onto each welded bolt 2 Feed the console wire back down into the Upright 3 Attach the Console 6 to the Upright with four 8 x 3 4 Round Head Screws 16 Be careful to avoid pinching the console wire Press the Resistance Knob 50 onto the Resistance Control 26 two adjustable wrenches and a rubber AN Console Wire Console pm Wire I 3 Find the Left Pedal 31 which has a ridge on the right side Atta2. Time This mode displays the length of time you have exercised Note If you stop exercising the time mode will pause until you resume Distance This mode displays the total distance you have completed in miles Laps This mode displays the number of 1 4 mile laps you have completed around the LED track Calorie This mode displays the approximate number of Calories you have burned Scan This mode displays the speed time distance laps and calorie modes for 5 seconds each in a repeating cycle BATTERY INSTALLATION Before the console can be operated two AA batter ies must be installed If you have not installed batter ies see assembly step 8 on page 8 10 HOW TO OPERATE THE CONSOLE If there is a thin sheet of clear plastic on the face of the console remove it 1 To turn on the power press the on reset button or simply begin exercising When the power is turned on one LED indicator will light in the LED track and the entire display will appear for two seconds The console will then be ready for operation 2 Select one of the five modes Scan mode When the power is turned on the scan mode will automatically be selected One mode indicator will show that the scan mode is selected and a flashing mode indica tor will show which mode is currently displayed Note If a different mode is selected you can select the scan mode again by repeatedly pressing the mode button SCAN CAL
3. LAPS SPEED TIME DIST Mode Indicators Speed time distance laps or calorie mode To select one of these modes for continuous display press the mode button repeatedly The mode indicators will show which mode is selected Make sure that the scan mode is not selected SCAN CAL LAPS SPEED TIME DIST The LED track represents a distance of 1 4 mile As you exercise the indicators around the track will light one at a time until you have completed 1 4 mile A new lap will then begin To reset the display press the on reset button To turn off the power simply wait for about four minutes Note The console has an auto off feature If the pedals are not moved and the console buttons are not pressed for four minutes the power will turn off automatically in order to conserve the batteries MAINTENANCE Inspect and tighten all parts of the PROFORM 485E regularly Replace any worn parts immediately The 485E can be wiped clean with a soft cloth and mild detergent Do not use abrasives or solvents To prevent damage to the console keep liquids away from the console Use only a sealable water bottle in the console 11 CONSOLE TROUBLE SHOOTING If the console does not function properly the batteries should be replaced To replace the batteries refer to assembly step 8 on page 8 STORAGE When storing the 485E remove the batteries from the console Keep the 485E in a clean dry location
4. 485E in a commercial rental or institutional setting WARNING Before beginning this or any exercise program consult your physician This is espe cially important for persons over the age of 35 or persons with pre existing health problems Read all instructions before using ICON assumes no responsibility for personal injury or property dam age sustained by or through the use of this product The decal shown at the right has been placed on the 485E If the decal is missing or if it is not legible please call our Do not allow children on or Customer Service Department around machine toll free at 1 800 999 3756 to Keep hands and feet awa order a free replacement decal from moving parts and contact Apply the decal in the location points shown Read owner s manual and follow instructions BEFORE YOU BEGIN Congratulations for selecting the PROFORM 485E low impact elliptical exerciser The 485E is an incredibly smooth exerciser that moves your feet in a natural elliptical path minimizing the impact on your knees and ankles And the unique 485E features adjustable resistance upper body and stationary han dlebars and a multi mode exercise monitor to help you get the most from your exercise Welcome to a whole new world of natural elliptical motion exercise from PROFORM For your benefit read this manual carefully before you use the PROFORM 485E If you have questions after reading the manual call our Custo
5. away from moisture and dust CONDITIONING GUIDELINES The following guidelines will help you to plan your exercise program Remember that proper nutrition and adequate rest are essential for successful results WARNING Before beginning this or any exer cise program consult your physician This is especially important for persons over the age of 35 or persons with pre existing health problems EXERCISE INTENSITY Whether your goal is to burn fat or to strengthen your cardiovascular system the key to achieving the desired results is to exercise with the proper intensity The proper intensity level can be found by using your heart rate as a guide The chart below shows recom mended heart rates for fat burning maximum fat burning and cardiovascular aerobic exercise HEART RATE TRAINING ZONES MIN 125 120 115 110 105 95 90 Fat Burn BPM 145 138 130 125 118 110 103 Max Burn max Y 165 155 AGE 20 30 140 130 50 60 115 Aerobic 80 To find the proper heart rate for you first find your age at the bottom of the chart ages are rounded off to the nearest ten years Next find the three numbers above your age The three numbers are your training zone The smallest number is the recommended heart rate for fat burning the middle number is the heart rate for maximum fat burning the largest number is the heart rate for aerobic exercise Burning Fat To burn fat effectively you must exercise at a rela tively
6. LACEMENT PARTS Back Cover LIMITED WARRANTY LL Back Cover IMPORTANT PRECAUTIONS WARNING To reduce the risk of serious injury read the following important precautions before using the PROFORM 485E 1 Read all instructions in this manual before using the 485E 2 Use the 485E only as described in this manual 3 It is the responsibility of the owner to ensure that all users of the 485E are ade quately informed of all precautions 4 Place the 485E on a level surface with a mat beneath it to protect the floor or carpet Keep the 485E indoors away from moisture and dust 5 Inspect and tighten all parts regularly Replace any worn parts immediately 6 Keep children under the age of 12 and pets away from the 485E at all times 7 The 485E should not be used by persons weighing more than 250 pounds 10 11 12 13 Wear appropriate clothing when using the 485E Always wear athletic shoes for foot protection When mounting and dismounting the 485E always hold the handlebars or the T handle and step onto and off the pedal that is in the lowest position Each time you stop exercising on the 485E allow the pedals to come to a complete stop before dismounting Always keep your back straight when using the 485E Do not arch your back If you feel pain or dizziness at any time while exercising stop immediately and begin cooling down The 485E is intended for in home use only Do not use the
7. ch the Left Pedal to one of the Pedal Arms 12 with three 8 x 3 4 Round Head Screws 16 as shown Repeat this step to attach the Right Pedal to the other Pedal Arm not shown 4 Make sure that there are two Pedal Arm Bushings 42 in each Pedal Arm 12 Slide a Handlebar Spacer 39 and the Pedal Arm 12 with the Left Pedal 31 onto a Handlebar 8 as shown Note These parts fit tightly it may be helpful to use the rubber mallet Refer to the PART IDENTIFICATION CHART on page 5 and identify the 3 4 Axle Caps 43 Tap a 3 4 Axle Cap onto the Handlebar Repeat this step to attach the other Pedal Arm 12 to the other Handlebar 8 5 Make sure that there are two Rear Pedal Arm Bushings 11 in each Pedal Arm 12 Slide a Pedal Arm Spacer 41 and the left Pedal Arm 12 onto the left Crank Arm 59 these parts fit tight ly it may be helpful to use the rubber mallet Be careful not to confuse the left Pedal Arm with the right Pedal Arm not shown look at the position of the Handlebar 8 to identify the left Pedal Arm Tap a 3 4 Axle Cap 48 onto the left Crank Arm 59 Repeat this step to attach the right Pedal Arm not shown 6 Refer to drawing 6a Push the left Pedal Arm 12 until the left Crank Arm 59 is at the back of the Side Shields 4 5 as shown Slide a Weld Spacer 49 and a Pivot Bushing 56 onto the left axle on the Upright 3 Make sure that the ope
8. dlebar 5 16 Lock Washer T Handle Rear Pedal Arm Bushing Pedal Arm 10 x 3 4 Screw Resistance Strap Strap Buckle 8 x 3 4 Round Head Screw 1 4 Nylon Locknut Adjustment Bracket 1 4 Eyebolt 3 8 Nylon Jam Nut Flywheel Axle Flywheel Bearing Flywheel Magnet Sensor Wire Reed Switch Resistance Control Cable Stabilizer Endcap Tension Spring 3 8 Nylon Locknut Belt Left Pedal Pulley w Shaft Crank Arm Extension 8 Tek Screw 5 16 Zinc Bolt Pulley Bearing Key No 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 Qty py RARAN M yDn Po Aa HAH A HSH a Na AA AMS YO an R0498A Description Pedal Disk 8 x 3 4 Tek Screw Handlebar Spacer Side Shield Bracket Pedal Arm Spacer Pedal Arm Bushing 3 4 Axle Cap 8 x 3 4 Flat Head Screw Resistance Control Bracket 8 Flat Washer Clamp Nut Clamp Bolt Weld Spacer Resistance Control Knob 8 x 1 Screw Return Spring 3 8 Washer 1 4 x 3 4 Screw 1 4 Black Nylon Locknut Pivot Bushing 5 8 Axle Cap Resistance Control Spacer Crank Arm Buckle Bracket 5 16 Zinc Washer 12 x 1 2 Screw T Handle Endcap Nylon Washer 3 4 Plastic Spacer 8 x 2 1 2 Screw Right Pedal User s Manual Side Shield Decal Warning Decal Hardware Kit Note indicates a n
9. horized service cen ters with all freight and other transportation charges prepaid accompanied by sufficient proof of purchase All returns must be pre authorized by ICON This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an ICON authorized service center to products used for commercial or rental pur poses or to products used as store displays No other warranty beyond that specifically set forth above is authorized by ICON ICON is not responsible or liable for indirect special or consequential damages arising out of or in con nection with the use or performance of the product or damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyment or use costs of removal installation or other consequential damages of whatsoever nature Some states do not allow the exclusion or limitation of inci dental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal righ
10. in 3 Calf Achilles Stretch With one leg in front of the other reach forward and place your hands against a wall Keep your back leg straight and your back foot flat on the floor Bend your front leg lean for ward and move your hips toward the wall Hold for 15 counts then relax Repeat 3 times for each leg To cause further stretching of the achilles tendons bend your back leg as well Stretches Calves achilles tendons and ankles 4 Quadriceps Stretch With one hand against a wall for balance reach back and grasp one foot with your other hand Bring your heel as close to your buttocks as possible Hold for 15 counts then relax Repeat 3 times for each leg Stretches Quadriceps and hip muscles EXERCISE FREQUENCY To maintain or improve your condition plan three work outs each week with at least one day of rest between workouts After a few months of regular exercise you may plan up to five workouts each week if desired Caution Be sure to progress at your own pace and avoid overdoing it Incorrect or excessive training may result in injury to your health Remember the key to success is make exercise a regular and enjoyable part of your everyday life 13 PART LIST Model No PFEL87075 Key No Qty GBMARANNNABAAA A MNOYNANAARARAAAANMANMNNYNGS A Description Frame Reed Switch Bracket Upright Right Side Shield Left Side Shield Console Foam Handlebar Grip Han
11. low intensity level for a sustained period of time During the first few minutes of exercise your body 12 uses easily accessible carbohydrate calories for ener gy Only after the first few minutes of exercise does your body begin to use stored fat calories for energy If your goal is to burn fat adjust the intensity of your exercise until your heart rate is near the smallest number in your training zone as you exercise For maximum fat burning adjust the intensity of your exercise until your heart rate is near the middle num ber in your training zone as you exercise Aerobic Exercise If your goal is to strengthen your cardiovascular sys tem your exercise must be aerobic Aerobic exer cise is activity that requires large amounts of oxygen for prolonged periods of time This increases the demand on the heart to pump blood to the muscles and on the lungs to oxygenate the blood For aerobic exercise adjust the intensity of your exercise until your heart rate is near the largest number in your training zone HOW TO MEASURE YOUR HEART RATE To measure your heart rate first exercise for at least four minutes Then stop exercising and place two fingers on your wrist as shown Take a six second heartbeat count and multiply the result by 10 to find your heart rate For example if your six second heartbeat count is 14 your heart rate is 140 beats per minute A six second count is used because your heart rate will d
12. mer Service Department toll free at 1 800 999 3756 Monday through Friday 6 a m until 6 p m Mountain Time excluding holidays To help us assist you please note the product model number and serial number before calling The model number is PFEL87075 The serial number can be found on a decal attached to the 485E see the front cover of this manual for the loca tion of the decal Before reading further please look at the drawing below and familiarize yourself with the parts that are labeled Water Bottle Holder Bottle not included Book Holder Resistance Knob T Handle Handlebar LEFT SIDE Pedal Upright Side Shield Pedal Disk Pedal Arm PART IDENTIFICATION CHART Use the chart below to identify the small parts used in the quantity needed for assembly Note Some small assembly The number in parenthesis below each part parts may have been pre attached for shipping If refers to the key number of the part from the PART a part is not in the parts bag check to see if it has LIST on page 14 The number after the dash indicates been pre attached 1 4 x 3 4 Screw 54 8 x 3 4 Round Head Screw 16 10 4 Handlebar Spacer 39 1 4 Black Nylon Locknut 55 3 8 Nylon Locknut 29 O Sie Weld Spacer 49 3 4 Axle Cap 43 5 8 Axle Cap 57 Pivot Bushing 56 Pedal Arm Spacer 41 3
13. n side of the Weld Spacer is facing the Upright and that the Pivot Bushing is turned as shown Slide the left Handlebar 8 onto the left axle on the Upright 3 Make sure that the Handlebar slides onto the Pivot Bushing 56 on the axle Slide another Pivot Bushing 56 onto the axle and start it into the Handlebar Using a rubber mallet and the extra Pedal Arm Spacer 41 not shown tap the Pivot Bushing into the Handlebar Remove the Pedal Arm Spacer Tap a 5 8 Axle Cap 57 onto the axle Repeat this step to attach the right side Handlebar not shown Attach the T Handle 10 to the Upright 3 with two 1 4 x 3 4 Screws 54 and two 1 4 Black Nylon Locknuts 55 The Console 6 requires two AA batteries not included Alkaline batteries are recommended To install batteries first locate the battery clip under the Console 6 Insert two batteries into the battery clip as shown Make sure that the batteries are turned so the negative ends of the batteries marked are touching the springs in the battery clip Make sure that all parts of the 485E are properly tightened Place a mat under the 485E to protect the floor or carpet from damage Batteries HOW TO USE THE PROFORM 485E HOW TO EXERCISE ON THE 485E To mount the 485E firmly hold the handlebars or the T handle and carefully step onto the pedal that is in the lo
14. on illustrated part indicates that an extra part may be included Specifications are subject to change without notice See the back cover of this manual for information about ordering replacement parts 14 EXPLODED DRAWING Model No PFEL87075 RO498A HOW TO ORDER REPLACEMENT PARTS To order replacement parts simply call our Customer Service Department toll free at 1 800 999 3756 Monday through Friday 6 a m until 6 p m Mountain Time excluding holidays To help us assist you please be pre pared to give the following information when calling The MODEL NUMBER of the product PFEL87075 The NAME of the product PROFORM 485E low impact elliptical exerciser The SERIAL NUMBER of the product see the front cover of this manual The KEY NUMBER and DESCRIPTION of the part s from page 14 of this manual PROFORM is a registered trademark of ICON Health Fitness Inc LIMITED WARRANTY ICON Health amp Fitness Inc ICON warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of ninety 90 days from the date of pur chase This warranty extends only to the original purchaser ICON s obligation under this warranty is lim ited to replacing or repairing at ICON s option the product at one of its authorized service centers All products for which warranty claim is made must be received by ICON at one of its aut
15. ra LOW IMPACT ELLIPTICAL EXERCISER Patent Pending Model No PFEL87075 Serial No Serial Number Decal QUESTIONS As a manufacturer we are committed to providing com plete customer satisfaction If you have questions or if there are missing or damaged parts we will guarantee complete satisfaction through direct assistance from our factory TO AVOID DELAYS PLEASE CALL DIRECT TO OUR TOLL FREE CUSTOMER HOT LINE The trained technicians on our customer hot line will provide immediate assistance free of charge CUSTOMER HOT LINE 1 800 999 3756 Mon Fri 6 a m 6 p m MST CAUTION n USER S MANUAL before using this equipment Keep this manual for future reference ra LOW IMPACT ELLIPTICAL EXERCISER TABLE OF CONTENTS IMPORTANT PRECAUTIONS cee pEr 3 BEFORE YOU BEGIN datar aa an AIA E he e RR Rees Se RE BoA 4 PART IDENTIFICATION CHART eee 5 ASSEMBLY sur dd reei hab heen ed Qtek paca wade Mesa waka aaa 6 HOW TO USE THE PROFORM 485E Le 9 MAINTENANCE AR eR aa awe SERGE RA ada 11 CONDITIONING GUIDELINES tnt 12 PART LIST Ed SERATA Ra A RR eae ae ade 14 EXPLODED DRAWING Es de eee eee Pb dee E 15 HOW TO ORDER REP
16. rop rapidly when you stop exercising Pe WORKOUT GUIDELINES Each workout should include the following three important parts A warm up consisting of 5 to 10 minutes of stretch ing and light exercise See page 13 A proper warm up increases your body temperature heart rate and circulation in preparation for exercise Training zone exercise consisting of 20 to 30 minutes of exercising with your heart rate in your training zone During the first few weeks of your exercise program do not keep your heart rate in your training zone for longer than 20 minutes A cool down with 5 to 10 minutes of stretching This will increase the flexibility of your muscles and will help to prevent post exercise problems SUGGESTED STRETCHES The correct form for several basic stretches is shown at the right Move slowly as you stretch never bounce 1 Toe Touch Stretch Stand with your knees bent slightly and slowly bend forward from your hips Allow your back and shoulders to relax as you reach down toward your toes as far as possible Hold for 15 counts then relax Repeat 3 times Stretches Hamstrings back of knees and back 2 Hamstring Stretch Sit with one leg extended Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg Reach toward your toes as far as possible Hold for 15 counts then relax Repeat 3 times for each leg Stretches Hamstrings lower back and gro
17. ts You may also have other rights which vary from state to state ICON HEALTH amp FITNESS INC 1500 S 1000 W LOGAN UT 84321 9813 Part No 145923 H00791 C R0498A Printed in China 1998 ICON Health amp Fitness Inc
18. west position Next step onto the other pedal Push the pedals until they begin to move with a con tinuous motion Note The pedal disks can turn in either direction it is recommended that you turn the pedal disks in the direction shown below however to give variety to your exercise you may choose to turn the pedal disks in the opposite direction Pedal Disk To dismount the 485E allow the pedals to come to a complete stop CAUTION The 485E does not have a freewheel the pedals will continue to move until the flywheel stops When the pedals are stationary step off the highest pedal first Then step off the low est pedal HOW TO ADJUST THE RESISTANCE OF THE PEDALS As you exercise you can adjust the resistance of the pedals with the resistance knob on the console To increase the resistance turn the knob clockwise to decrease the resistance turn the knob counterclockwise Resistance Knob DESCRIPTION OF THE CONSOLE The console is designed to help you get the most from your workouts As you exercise you can watch your progress around the LED track while the display provides continuous exercise feedback The six modes of the display are described below A O O O PACER O 25 Mile Lap 0000000 LED Track SCAN CAL LAPS 8888 SPEED TIME DIST MODE ON RESET Speed This mode displays your current exercise speed in miles per hour
Download Pdf Manuals
Related Search