SH7729/SH7709A Evaluation Chip Board (HS7729EBH81H
Contents
1. 3 3 Connecting the HS7410PWB20H and PWB30H Figure 3 6 shows the connection of the HS7410PWB20H and PWB30H Check the location of the connectors that are to be connected on the HS7410PWB20H and PWB30H Align the connectors on the HS7410PWB20H with those on the PWB30H according to their numbers and connect them while holding the PWB30H securely Gradually tighten the screws alternately and repeatedly in a diagonal line on the HS7410PWB20H CAUTION Forcefully tightening only one screw will damage the connectors Also this will apply stress to the soldered QFP sockets on the user system and cause cracks in the solder A WARNING The connector and socket structures prevent the connectors from being inserted in the wrong direction If the connectors cannot be fully inserted or force is required pin 1 on the connector and pin 1 on the socket may not be aligned correctly Forcible insertion will apply stress to the soldered sockets on the user system and cause cracks in the solder Recheck the location of pin 1 on both sides and re insert the connector 23 HITACHI HS7410PWB20H PWB30H Figure 3 6 Connecting the HS7410PWB20H and PWB30H 24 HITACHI 4 1 Section 4 Mounting the SH7729 SH7709A Mounting the SH7729 SH7709A on the User System When mounting the SH7729 SH7709A on the user system position the SH7729 SH7709A on the IC socket after checking the direction of pin 1 and tighten the four screws M2 x 6 m2. IMPORTANT INFORMATION READ FIRST READ this user s manual before using this evaluation chip board hereafter referred to as the EV chip board for Hitachi microcomputer HD6417729 or HD6417709A KEEP the user s manual handy for future reference Do not attempt to use the EV chip board until you fully understand its mechanism EV Chip Board Throughout this document the term EV chip board shall be defined as the following products produced only by Hitachi Ltd excluding all subsidiary products e EV chip board e Device control board The user system or a host computer is not included in this definition Purpose of the EV Chip Board This EV chip board is a software and hardware development tool for systems employing the Hitachi microcomputer HD6417729 or HD6417709A hereafter referred to as SH7729 SH7709A The E8000 emulator and the user system can be connected through the EV chip board This EV chip board must only be used for the above purpose Improvement Policy Hitachi Ltd including its subsidiaries hereafter collectively referred to as Hitachi pursues a policy of continuing improvement in design performance and safety of the EV chip board Hitachi reserves the right to change wholly or partially the specifications design user s manual and other documentation at any time without notice Target User of the EV Chip Board This EV chip board should only be used by those who have carefully read and thorou
3. certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Elect
4. who sold this EV chip board Table 1 1 EV chip Board HS7729EBH81H Components Item Quantity Remarks EV chip board 1 Consists of two boards HS7729EBH81H HS7410PWB20H for connecting to the E8000 station HS7729PWB30H IC socket QFP 208 QPACK208SD manufactured by ELETECH CORPORATION p 7 7 c MEET 0 0 oo ELETECH CORPORATION For mounting the SH7729 Setews or the 16 Sockeiy 4 WE ee tor mounting the wou qucd Mere Screws for ihe IC socket 4 M2 x 30 mm for attaching the EV chip board Spacers 4 13 mm for attaching the EV chip board Four flat washers and four spring washers Screws for the spacers 4 M3 x 6 mm for attaching the EV chip board Four flat washers four spring washers and four nuts 1 HITACHI Table 1 2 EV chip Board HS7709AEBH81H Components Item Quantity Remarks EV chip board 1 Consists of two boards HS7709AEBH81H HS7410PWB20H for connecting to the E8000 station HS7709APWBSOH IC socket QFP 208 PACK208SD manufactured by ELETECH CORPORATION IC socket cover 1 HQPACK208SD manufactured by TOKYO ELETECH CORPORATION For mounting the SH7729 Spacers 4 13 mm for attaching the EV chip board Four flat washers and four spring washers Screws for the spacers 4 M3 x 6 mm for attaching the EV chip board Four flat washers four spring washers and four nuts E G uide pins 3 For positioning the IC socket Specific screwdriver 1 Screwdrive
5. ATION Unit mm Tolerance 0 10 mm Figure 2 2 Component Height Restriction 11 HITACHI A WARNING The screw holes of the EV chip board for attaching the board are connected to the GND of the board Confirm that the spacers nuts or washers of the EV chip board do not make contact with the patterns or components other than the GND on the user system Failure to do so will result in a FIRE HAZARD and will damage the user system and emulator or will result in PERSONAL INJURY The USER PROGRAM will be LOST Ground pattern Bottom view of the HS7729PWB30H 12 HITACHI Section 3 Connecting the EV Chip Board to the User System 3 1 Connecting the HS7729PWB30H HS7709APWB30H to the User System 3 1 1 Installing the QFP 208 Package IC Socket This EV chip board is designed exclusively for the supplied IC socket type number NQPACK208SD manufactured by TOKYO ELETECH CORPORATION Therefore it cannot be used with other IC sockets e Positioning the IC socket Position the IC socket with the supplied guide pins as shown in figure 3 1 Apply an epoxy adhesive to the tips of the four protrusions on the bottom surface of the IC socket to bond the IC socket to the user system board 13 HITACHI IC socket cover Apply epoxy adhesive at four points Guide pins IC socket Pin 1 mark Bottom view of IC socket User system board Figure 3 1 Positioning the IC Socket 14 HITACHI Solderi
6. H7709A on the User System sse 25 HITACHI Figures Figure 1 1 Figure 2 1 Figure 2 2 Figure 3 1 Figure 3 2 Figure 3 3 Figure 3 4 Figure 3 5 Figure 3 6 Figure 4 1 Tables Table 1 1 Table 1 2 Table 2 1 EV Chip Board bach Den necem E Ref 3 Recommended Mounting Pad Dimensions sese 10 Component Height Restriction eese ener nennen 11 Positioning the IC Socket nene enn ee entente nre 14 Top View of the PWB30H 5 eerte ette retener ere tiep den 16 Screw Tightening Sequence Top View of the PWB30H sees 18 Connecting the PWB30H to the User System sese 19 Connecting Trace Cables to the EV Chip Board sese 22 Connecting the HS7410PWB20H and PWBS3O0H see 24 Mounting the SH7729 SH7709A scccsssssssessesscessenseeeseecseeceevsnevensessnessessesssees 26 EV chip Board HS7729EBH81H Components eee 1 EV chip Board HS7709AEBH81H Components seen 2 Pin Assignment of the 208 Pin QFP IC Socket sese 6 HITACHI Section 1 Components 1 1 EV Chip Board Components Tables 1 1 and 1 2 list the product components of the EV chip board respectively HS7729EBH8 1H 208 pin QFP IC socket type H87709AEBHS1H 208 pin QFP IC socket type Check all the components after unpacking If any components are missing contact the Hitachi salesperson
7. HS7729EBH81H HS7709AEBHS81H for the E8000 Emulator User s Manual Renesas Electronics as electoronics com www renesas Cautions Hitachi neither warrants nor grants licenses of any rights of Hitachi s or any third party s patent copyright trademark or other intellectual property rights for information contained in this document Hitachi bears no responsibility for problems that may arise with third party s rights including intellectual property rights in connection with use of the information contained in this document Products and product specifications may be subject to change without notice Confirm that you have received the latest product standards or specifications before final design purchase or use Hitachi makes every attempt to ensure that its products are of high quality and reliability However contact Hitachi s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury such as aerospace aeronautics nuclear power combustion control transportation traffic safety equipment or medical equipment for life support Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating operating supply voltage range heat radiation characteristics installation conditions and other characteristi
8. NI AJPTL A 8 HITACHI 2 2 Connector Mounting Position of the User System Figure 2 1 shows the recommended mounting pad footprint dimensions and the hole position for installing the EV chip board for the supplied 208 pin QFP IC socket NQPACK208SD manufactured by TOKYO ELETECH CORPORATION The screw holes in the EV chip board for attaching the board are connected to the GND of the board The ground lines can be enhanced by forming a GND pattern at the screw hole locations of the user system enabling stable operation during high speed emulation When a hole for EV chip board is set to fix the EV chip board and the user system by using a spacer a crack in the soldered parts on the IC socket NQPACK208SD can be prevented from being generated 9 HITACHI 0 5x 51 25 5 1 E ra Q9 Pin 1 mark pore i I 4 94 i a i 71 5 i 7 75 mS External frame of the EV chip board i A i Unit mm A Center line of the IC socket i Tolerance 0 10 mm E Pattern inhibition area Figure 2 1 Recommended Mounting Pad Dimensions 10 HITACHI Comply with the user system component height restriction shown in Figure 2 2 within the external frame of the EV chip board shown in Figure 2 1 EV chip board HS7729EBH81H or HS7709AEBH81H User system board User system socket NQPACK208SD manufactured by TOKYO ELETECH CORPOR
9. TURE OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE EV CHIP BOARD THE USE OF ANY EV CHIP BOARD OR ITS DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS WARRANTY THIS EV CHIP BOARD IS SOLD AS IS AND YOU MUST ASSUME ALL RISK FOR THE USE AND RESULTS OBTAINED FROM THE EV CHIP BOARD HITACHI State Law Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which may vary from state to state The Warranty is Void in the Following Cases Hitachi shall have no liability or legal responsibility for any problems caused by misuse abuse misapplication neglect improper handling installation repair or modifications of the EV chip board without Hitachi s prior written consent or any problems caused by the user system All Rights Reserved This user s manual and EV chip board are copyrighted and all rights are reserved by Hitachi No part of this user s manual all or part may be reproduced or duplicated in any form in hard copy or machine readable form by any means available without Hitachi s prior written consent Other Important Things to Keep in Mind 1 Circuitry and other examples described herein are meant merely to indicate the characteristics and p
10. To our customers Old Company Name in Catalogs and Other Documents On April 1 2010 NEC Electronics Corporation merged with Renesas Technology Corporation and Renesas Electronics Corporation took over all the business of both companies Therefore although the old company name remains in this document it is a valid Renesas Electronics document We appreciate your understanding Renesas Electronics website http www renesas com April 1 5 2010 Renesas Electronics Corporation Issued by Renesas Electronics Corporation http www renesas com Send any inquiries to http www renesas com inquiry 2 NE S AS 8 10 11 12 Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is gr
11. anted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document b
12. ce equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under
13. cs Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges Even within the guaranteed ranges consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail safes so that the equipment incorporating Hitachi product does not cause bodily injury fire or other consequential damage due to operation of the Hitachi product This product is not designed to be radiation resistant No one is permitted to reproduce or duplicate in any form the whole or part of this document without written approval from Hitachi Contact Hitachi s sales office for any questions regarding this document or Hitachi semiconductor products Preface This manual describes how to connect and operate the EV chip board The EV chip board incorporates an evaluation chip for connection to a user system that uses the SH7729 SH7709A with the E8000 emulator Read and understand Sec 3 Preparation before Use of the E8000 Emulator User s Manual before using this EV chip board CAUTION The EV chip board is only for connection to a user system that uses the SH7729 SH7709A with the E8000 emulator It cannot be used for user systems that target other devices The EV chip board is connected only with the device control board HS7729EDD81H Read section 2 Configuration in Part I E8000 Guide of the E8000 SH7729 SH7709A Emulator User s Manual HITACHI
14. erformance of Hitachi s semiconductor products Hitachi assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein 2 No license is granted by implication or otherwise under any patents or other rights of any third party or Hitachi Figures Some figures in this user s manual may show items different from your actual system Limited Anticipation of Danger Hitachi cannot anticipate every possible circumstance that might involve a potential hazard The warnings in this user s manual and on the EV chip board are therefore not all inclusive Therefore you must use the EV chip board safely at your own risk I HITACHI SAFETY PAGE READ FIRST READ this user s manual before using this EV chip board KEEP the user s manual handy for future reference Do not attempt to use the EV chip board until you fully understand its mechanism DEFINITION OF SIGNAL WORDS gt This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potent
15. ghly understood the information and restrictions contained in the user s manual Do not attempt to use the EV chip board until you fully understand its mechanism It is highly recommended that first time users be instructed by users that are well versed in the operation of the EV chip board HITACHI LIMITED WARRANTY Hitachi warrants its EV chip boards to be manufactured in accordance with published specifications and free from defects in material and or workmanship Hitachi at its option will repair or replace any EV chip boards returned intact to the factory transportation charges prepaid which Hitachi upon inspection determine to be defective in material and or workmanship The foregoing shall constitute the sole remedy for any breach of Hitachi s warranty See the Hitachi warranty booklet for details on the warranty period This warranty extends only to you the original Purchaser It is not transferable to anyone who subsequently purchases the EV chip board from you Hitachi is not liable for any claim made by a third party or made by you for a third party DISCLAIMER HITACHI MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED ORAL OR WRITTEN EXCEPT AS PROVIDED HEREIN INCLUDING WITHOUT LIMITATION THEREOF WARRANTIES AS TO MARKETABILITY MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR USE OR AGAINST INFRINGEMENT OF ANY PATENT IN NO EVENT SHALL HITACHI BE LIABLE FOR ANY DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NA
16. ially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE emphasizes essential information lt HITACHI A WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the EV chip board or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Always switch OFF the EV chip board and user system before connecting or disconnecting any CABLES or PARTS 2 Always before connecting make sure that pin 1 on both sides is correctly aligned HITACHI Warnings on EV Chip Board Usage Warnings described below apply as long as you use the EV chip board Be sure to read and understand the warnings below before using the EV chip board Note that these are the main warnings not the complete list A WARNING Always switch OFF the EV chip board and user system before connecting or disconnecting any CABLES or PARTS Failure to do so will result in a FIRE HAZARD and will damage the user system and the EV chip board or will result in PERSONAL INJURY The USER PROGRAM will be LOST VI HITACHI CAUTION Place the emulator station and EV chip board so that the cable is not bent or twisted A bent or twisted cable will impose stress on the user interface lead
17. ing to connection or contact failure Make sure that the emulator station is placed in a secure position so that it does not move during use nor impose stress on the user interface HITACHI Z E8000 T J M VII HITACHI Contents secuond YMCOMPONEMIS oss re Rath nna det cadet ouem eats eager taal as 1 1 4 EV Chip Board Components sees nennen trennen trenes 1 1 2 Component Names onere pee e er P shoes eae ree epe tee ries 3 Section 2 Preparation before Uses siciisssgsaccatenccerasscvedeatecnaade Uo Rena Ph pene Pe ear nat rea 5 2 1 Preparing the User System oo eee a n n a a r i 5 2 2 Connector Mounting Position of the User System sse 9 Section 3 Connecting the EV Chip Board to the User System 13 3 1 Connecting the HS7729PWB30H HS7709APWB30H to the User System 13 3 1 1 Installing the QFP 208 Package IC Socket eee 13 3 1 2 Connecting the HS7729PWB30H HS7709APWB30H to the User System 15 3 2 Connecting the Trace Cables etre ERI teet Rede bete eene Ses 20 32 Connecting the Trace Cables to the E8000 Station sss 20 3 22 2 Connecting the Trace Cables to the EV Chip Board sess 21 3 3 Connecting the HS7410PWB20H and PWB30H seen 23 Section 4 Mounting the SH7729 SH7709A cee ceesseceeneceeeeceeeeeceeeeeceeeeeenteeeees 25 4 1 Mounting the SH7729 S
18. m on the IC socket cover as shown in figure 4 1 When tightening the screws hold the IC socket so that it does not twist CAUTION 1 2 3 4 Before mounting the SH7729 SH7709A on the user system check the location of pin 1 on both sides Use the supplied screwdriver to tighten the screw Set the tightening torque to 0 98 kgfecm 0 098 Nem or lower If the torque cannot be set stop tightening the screw as soon as the tightening force greatly increases If the screw is tightened more forcibly than necessary the screw threads in the IC socket may be damaged or a contact failure may occur due to a solder crack on the IC socket If an electric conduction error occurs during operation a crack may have occurred in the soldered section of the IC socket Check the electric conduction with a tester and resolder the cracked section 25 HITACHI Screws M2 0 x 6 mm for mounting MCU i T U IC socket cover HQPACK208SD manufactured by TOKYO ELETECH CORPORATION KF 78 MCU SH7729 SH7709A i i E Pin 1 mark Y IC socket 18 HQPACK208SD manufactured by possum TOKYO ELETECH CORPORATION User system Figure 4 1 Mounting the SH7729 SH7709A 26 HITACHI
19. ng the IC socket After the epoxy adhesive has hardened solder the IC socket At this time install the cover on the IC socket to prevent flux or solder from adhering to the guide pins Use more solder than usual so that a fillet is formed on the lead edge being soldered 3 1 2 Connecting the HS7729PWB30H HS7709A PWB30H to the User System 1 At shipment the HS7410PWB20H and HS7729PWB30H are connected to each other HS7729EBH81H The HS7410PWB20H and HS7709APWB30H are connected to each other HS7709AEBH81H These are referred to as PWB30H Before connecting the EV chip board to the user system separate the HS7410PWB20H from the PWB30H The HS7410PWB20H is connected to the PWB30H through three connectors as shown in figure 3 2 15 HITACHI Figure 3 2 Top View of the PWB30H 16 HITACHI 2 Insert the plastic rod between the HS7410PWB20H and PWB30H and lever them apart Alternately between the four corners of the EV chip board gradually force the HS7410PWB20H and PWB30H apart CAUTION The following figure shows the position of the SH7729 SH7709A evaluation chip and connectors between the HS7410PWB20H and PWB30H Insert the plastic rod in the A direction as shown in the figure If the plastic rod is inserted in the B direction wiring patterns and IC leads on the board will be damaged Forcefully loosening only one connector applies unusual force to other connectors thus damaging the connectors and causing contact failu
20. r for fixing the IC socket 2 HITACHI 1 2 Component Names The component names of the EV chip board are described below Pin 1 mark Top view of HS7729EBH81H or Bottom view of HS7729EBH81H or HS7709AEBH81H HS7709AEBH81H ca Station to EV chip board interface connectors Side view of HS7729EBH81H or HS7709AEBH81H Figure 1 1 EV Chip Board 1 Station to EV chip board interface For trace cable 3 which connects the E8000 connector CN3 station to the EV chip board 2 Station to EV chip board interface For trace cable 2 which connects the E8000 connector CN2 station to the EV chip board 3 Station to EV chip board interface For trace cable 1 which connects the E8000 connector CN1 station to the EV chip board 4 Crystal oscillator terminals For installing a crystal oscillator to be used as a clock source for the SH7729 SH7709A 5 User system connector For connecting the user system 6 Board connector For connecting HS7410PWB20H and HS7729PWB30H or HS7709APWB30H 3 HITACHI 7 HS7410PWB20H Includes connectors for interfacing with the E8000 station 8 HS7729PWB30H Mounts the SH7729 and IC socket for connecting with the user system 9 HS7709APWB30H Mounts the SH7709A and IC socket for connecting with the user system 10 Spacer Notes 1 Items 1 through 8 above are called as HS7729EBH81H 2 Items 1 through 7 and 9 are called as HS7709AEBHS81H 4 HITACHI Section 2 Preparation before Use 2 1 Prepa
21. r system check the location of pin 1 on both sides 2 If a malfunction occurs during operation a crack may have occurred in the soldered section of the IC socket Check the electric conduction with a tester and resolder the cracked section Screws M2 x 10 mm Spring washer Spacer Evaluation chip Pin 1 mark Socket anchoring i ek metal fittings JJ gv Flat washer N Y Y e Spring washer A e e Nut ET D D e Figure 3 4 Connecting the PWB30H to the User System 19 HITACHI 3 2 Connecting the Trace Cables 4 WARNING Always switch OFF the emulator and user system before connecting or disconnecting any CABLES or sockets Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator or will result in PERSONAL INJURY The USER PROGRAM will be LOST 3 2 1 Connecting the Trace Cables to the E8000 Station Before connecting the trace cables to the HS7410PWB20H connect the trace cables to the E8000 station CAUTION At shipment trace cables CN2 and CN3 to be connected to the E8000 station are bound into a bundle and trace cables CN1 CN2 and CN3 to be connected to the EV chip board are bound into a bundle to prevent an insertion error For more information on connecting the EV Chip board to the E8000 station refer to section 3 2 2 Connecting the EV Chip Board in the SH7729 SH7709A E8000 Emulator User s Manual 20 HITACHI 3 2 2 Connecting the Trace Cable
22. res Pay attention to the IC and wiring patterns on the EV chip board when inserting the plastic rod O es lo O Connectors gb sH7729 sH77094 3 Attach the spacers on the PWB30H and install the PWB30H onto the user system after checking the pin 1 location of the IC socket 17 HITACHI 4 Attach the HS7420PWB30H to the IC socket on the user system with four screws M2 x 10 mm Gradually tighten the screws alternately in a figure 8 pattern see figure 3 3 Never forcibly tighten only one screw Otherwise a contact failure will occur or performance will be degraded When tightening the screws hold the IC socket so that it does not twist 5 Affix the IC socket with screws by using the supplied screwdriver Stop tightening each screw when the tightening force greatly increases an approximate target is 0 098 Nem or lower when the torque can be set If the screw is tightened more forcibly than necessary the screw threads in the IC socket may be damaged or a contact failure may occur due to a solder crack on the IC socket Figure 3 3 Screw Tightening Sequence Top View of the PWB30H 6 Affix the PWB30H to the user system with the appropriate screws and nuts See figure 3 4 Cracking due to insertion of the trace cable can be prevented in the soldered section of the socket on the user system 18 HITACHI CAUTION 1 Before connecting the EV chip board to the use
23. ring the User System Table 2 1 lists the user interface pin assignment of the 208 pin QFP IC socket NQPACK208SD manufactured by TOKYO ELETECH CORPORATION when the target MCU is the SH7729 SH7709A 5 HITACHI Table 2 1 Pin Assignment of the 208 Pin QFP IC Socket Pin No Pin Name Pin No Pin Name Pin No Pin Name 1 MD1 32 D16 PTA 0 63 A8 29 Vcc 1 8V 60 A5 91 WE2 DQMUL ICIORD PTK 6 30 D18 PTA 2 61 A6 92 WE3 DQMUU ICIOWR PTK 7 31 D17 PTA 1 62 A7 93 RD WE 6 HITACHI Table 2 1 Pin Assignment of the 208 Pin QFP IC Socket cont Pin No Pin Name Pin No Pin Name Pin No Pin Name 94 AUDSYNC PTE 7 122 BREQ 150 Vcc PLL2 1 8V 7 HITACHI Table 2 1 Pin Assignment of the 208 Pin QFP IC Socket cont Pin No Pin Name Pin No Pin Name 176 CTS2 IRQ5 SCP 7 204 AN S PTL 5 177 MCS7 PTQ 7 PINT 205 Avc 33V s i is sSsSOSSSSCS 178 MCSG PTC G PINTIe 206 AN DGJDAMJPTLIO 170 MCSSPTOBJPINTI 207 ANZJDADJPTLU 0 38e WARMUP k LI e LL A ghost 184 RESETOUT PTD 2 ee ee ser cd Tasca atest sateen gate E oe E 187 MCS1 PTCHYPINTH TTT 188 MCSOPPTCIOPINTIO TTI Hg DRAKO PTDI1 ge ee ee ee ee aoe 190 DAK UPTDJ 000000 191 DREQUPTD A 000000 192 DREQIPTD G 0 7198 RESETP 000000 PUNE Me ee re poe gee poe ee NS EM NEMPE 195 MDS KC NO DAN cee UON ee un eee eg eg ee ee eye eee K GM O TTCS 198 AVSS 0000000 n a O 802 ANBIPTLS nnn 203 A
24. ronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics To all our customers Regarding the change of names mentioned in the document such as Hitachi Electric and Hitachi XX to Renesas Technology Corp The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas Technology Corporation on April 1st 2003 These operations include microcomputer logic analog and discrete devices and memory chips other than DRAMs flash memory SRAMs etc Accordingly although Hitachi Hitachi Ltd Hitachi Semiconductors and other Hitachi brand names are mentioned in the document these names have in fact all been changed to Renesas Technology Corp Thank you for your understanding Except for our corporate trademark logo and corporate statement no changes whatsoever have been made to the contents of the document and these changes do not constitute any alteration to the contents of the document itself Renesas Technology Home Page http www renesas com Renesas Technology Corp Customer Support Dept April 1 2003 24 N SAS Renesas Technology Corp C 7 D Ims on lt D D 44 NE S AS SH7729 SH7709A Evaluation Chip Board
25. s to the EV Chip Board Align the trace cables with the station to EV chip board interface connectors CN1 CN2 and CN3 on the EV chip board Confirm that each trace cable connected to a connector on the E8000 station is also connected to its corresponding station to EV chip board interface connector on the EV chip board For the prevention of insertion errors colors are specified on the trace cable connectors and the corresponding EV chip board interface connectors CN1 red CN2 yellow CN3 blue CAUTION For the prevention of insertion errors colors are specified on the trace cable connectors and the corresponding EV chip board interface connectors Trace cable screws CN1 red CN3 blue CN2 yellow CN1 red Trace cable connector Top view of the HS7410PWB20H 21 HITACHI Tighten the screws to connect the trace cable connectors to the station to EV chip board interface connectors while holding the HS7410PWB20H securely Trace cable CN3 b Trace cable CN2 Trace cable CN1 p Station to EV chip board interface connector CN1 Station to EV chip board interface connector CN3 Station to EV chip board interface connector CN2 Figure 3 5 Connecting Trace Cables to the EV Chip Board A WARNING Make sure the connector shapes and numbers are correctly matched when connecting the trace cables to the station to EV chip board interface connectors Failure to do so will result in a FIRE HAZARD 22 HITACHI
26. ut Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers offi
Download Pdf Manuals
Related Search