User manual Refrigerator ZRX71100WA
Contents
1. Closing the door 1 Clean the door gaskets 2 If necessary adjust the door Refer to In stallation Technical data The door is not closed correctly Refer to Closing the door Set a higher temperature 3 If necessary replace the defective door gaskets Contact the Service Center Dimension Height Width Depth Voltage Frequency The technical information are situated in the rat ing plate on the internal left side of the appli ance and in the energy label Installation 520 mm 525 mm 587 mm 230 V 50 Hz Caution Read the Safety Information carefully for your safety and correct operation of the appliance before installing the appliance Positioning This appliance can be installed in a dry well ventilated indoor garage or cellar also but for optimum performance install this appliance at a location where the ambient temperature corre sponds to the climate class indicated on the rating plate of the appliance Climate Ambient temperature class SN 10 C to 32 C N 16 C to 32 C ST 16 C to 38 C T 16 C to 43 C Rear spacers In the bag with the documentation there are two spacers which must be fitted as shown in the figure www zanussi com Using fine strokes of hammer put them in their place Location The appliance should be installed well away from sources of heat such as radiators boilers direct sunlight etc Ensure that air can circulate f2. the quantity of food stored the location of the appliance Important If the ambient temperature is high or the appliance is fully loaded and the appliance is set to the lowest temperatures it may run continuously causing frost to form on the rear wall In this case the dial must be set to a higher temperature to allow automatic defrosting and therefore reduced energy consumption with lukewarm water and some neutral soap so as to remove the typical smell of a brand new product then dry thoroughly www zanussi com Important Do not use detergents or abrasive powders as these will damage the finish Daily use Using of the ice maker compartment This appliance is equipped with an ice maker compartment In the ice maker compartment can be reached 2 C or lower temperature depending on set ting of thermostat control Helpful hints and tips Normal Operating Sounds You may hear a faint gurgling and a bubbling sound when the refrigerant is pumped through the coils or tubing This is correct When the compressor is on the refrigerant is being pumped around and you will hear a whirring sound and a pulsating noise from the compressor This is correct The thermic dilatation might cause a sudden cracking noise It is natural not dangerous physical phenomenon This is correct When the compressor switches on or switches off you will hear a faint click of the temperature regulator This is correct H
3. User manual Refrigerator U S R MANUAL ZRX71100WA ZAN USSI Contents Safety instructions Operation First use _ Daily us oaia Helpful hints and tips auf BD A Safety instructions In the interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully in cluding its hints and warnings To avoid unnec essary mistakes and accidents it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features Save these instructions and make sure that they remain with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on ap pliance use and safety For the safety of life and property keep the pre cautions of these user s instructions as the manufacturer is not responsible for damages caused by omission Children and vulnerable people safety This appliance is not intended for use by per sons including children with reduced physi cal sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction con cerning use of the appliance by a person re sponsible for their safety Children should be supervised to ensure that they do not play with the appliance Keep all packaging well away from children There is risk of suffocation If you are discarding the appliance pull t
4. 12 Replace the hinge cover 13 Relocate the han dle and the plastic plugs to the opposite side 14 Level the appli ance wait for at least four hours and then connect it to the pow er socket The manufacturer declines any liability should these safety measures not be observed G gt A B c D E XN y www zanussi com Important The wires in the mains lead are coloured in accordance with the following code A Green and Yellow Earth C Brown Live D Blue Neutral As the colours of the wires in the mains lead of this appliance may not correspond with the col oured markings identifying the terminals in your plug proceed as follows 1 Connect the wire coloured green and yel low to the terminal marked either with the letter E or by the earth symbol or col oured green and yellow 2 Connect the wire coloured blue to the ter minal either marked with the letter N or coloured black Environmental concerns The symbol amp A on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent www zanussi com 3 Connect the wire coloured brown to the terminal either marked with the L or col oured red 4 Check that n
5. O position Temperature regulation The temperature is automatically regulated To operate the appliance proceed as follows turn the Temperature regulator toward lower settings to obtain the minimum coldness turn the Temperature regulator toward higher settings to obtain the maximum coldness In the ice making compartment 2 C or lower temperature can be reached if the Temperature regulator is set according to fol lowing table Ambient temperature Temperature regula tor setting First use Cleaning the interior Before using the appliance for the first time wash the interior and all internal accessories 4 Environment Protection This appliance does not contain gasses which could damage the ozone layer in ei ther its refrigerant circuit or insulation materials The appliance shall not be discarded together with the urban refuse and rubbish The insula tion foam contains flammable gases the appli ance shall be disposed according to the appli cable regulations to obtain from your local au thorities Avoid damaging the cooling unit es pecially at the rear near the heat exchanger The materials used on this appliance marked by the symbol 5 are recyclable 10 16C Wl 16 25 C 1 2 25 32 C De 32 38 C 3 4 However the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on room temperature how often the door is opened
6. in order to remove the foot 3 Unscrew the 2 re taining screws and re move the hinge from the appliance 4 Take the door off Do a final check to make sure that All screws are tightened The door opens and closes correctly If the ambient temperature is cold i e in Win ter the gasket may not fit perfectly to the cabi net In that case wait for the natural fitting of the gasket In case you do not want to carry out the above mentioned operations contact the nearest After Sales Service Force The After Sales Service specialist will carry out the reversibility of the doors at your cost Electrical Connection Caution Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person A Warning This appliance must be earthed 10 7 Fix the door hinge and the corresponding foot on the opposite side and then the oth er loosened foot at the former place of the door hinge as shown in the Figure 8 Please make sure to place the lower foot below the door hinge The lower foot is recognizable by its 4 ribs on the outer surface 9 Fix the door onto the lower hinge pin 10 To fit top door hinge remove the plastic blanking plugs carefully and refit them in the holes left by the hinge retaining screws 11 Refit the top hinge using the 2 retaining screws taking care that the edge of the door is parallel with side of the cabinet
7. ane R600a is con tained within the refrigerant circuit of the ap pliance a natural gas with a high level of en vironmental compatibility which is neverthe less flammable During transportation and installation of the appliance be certain that none of the com www zanussi com ponents of the refrigerant circuit become damaged If the refrigerant circuit should become dam aged avoid open flames and sources of ignition thoroughly ventilate the room in which the appliance is situated It is dangerous to alter the specifications or modify this product in any way Any damage to the cord may cause a short circuit fire and or electric shock Warning Any electrical component pow er cord plug compressor must be re placed by a certified service agent or qualified service personnel to avoid hazard 1 Power cord must not be lengthened 2 Make sure that the power plug is not squashed or damaged by the back of the appliance A squashed or damaged power plug may overheat and cause a fire 3 Make sure that you can come to the mains plug of the appliance 4 Do not pull the mains cable 5 If the power plug socket is loose do not insert the power plug There is a risk of electric shock or fire 6 You must not operate the appliance without the lamp cover if foreseen of interior lighting This appliance is heavy Care should be tak en when moving it Do not remove nor touch items from th
8. c paragraphs Unpack the appliance and check if there are damages on it Do not connect the appliance if it is damaged Report possible damages immediately to the place you bought it In that case retain packing It is advisable to wait at least four hours be fore connecting the appliance to allow the oil to flow back in the compressor Adequate air circulation should be around the appliance lacking this leads to overheat ing To achieve sufficient ventilation follow the instructions relevant to installation Wherever possible the back of the product should be against a wall to avoid touching or catching warm parts compressor condens er to prevent possible burn The appliance must not be located close to radiators or cookers Make sure that the mains plug is accessible after the installation of the appliance Connect to potable water supply only If a water connection is foreseen Service Any electrical work required to do the servic ing of the appliance should be carried out by a qualified electrician or competent person This product must be serviced by an author ized Service Centre and only genuine spare parts must be used Operation Switching on Insert the plug into the wall socket Turn the Temperature regulator clockwise to a medium setting The Temperature Regulator is situated on the side of the cabinet Switching off To turn off the appliance turn the Temperature regulator to the
9. e freezer compartment if your hands are damp wet as this could cause skin abrasions or frost freezer burns Avoid prolonged exposure of the appliance to direct sunlight Bulb lamps if foreseen used in this appli ance are special purpose lamps selected for household appliances use only They are not suitable for household room illumination Daily Use Do not put hot pot on the plastic parts in the appliance www zanussi com Do not store flammable gas and liquid in the appliance because they may explode Appliance s manufacturers storage recom mendations should be strictly adhered to Refer to relevant instructions Do not place carbonated or fizzy drinks in the ice maker compartment as it creates pres sure on the container which may cause it to explode resulting in damage to the appli ance Ice lollies can cause frost burns if consumed straight from the appliance Care and cleaning Before maintenance switch off the appliance and disconnect the mains plug from the mains socket Do not clean the appliance with metal ob jects Do not use sharp objects to remove frost from the appliance Use a plastic scraper Never use a hair drier or other heating appli ances to speed up defrosting Excessive heat may damage the plastic interior and humidity could enter the electric system making it live Installation Important For electrical connection carefully follow the instructions given in specifi
10. e of the appliance and save electricity con sumption Important Take care of not to damage the cooling system Many proprietary kitchen surface cleaners con tain chemicals that can attack damage the plastics used in this appliance For this reason it is recommended that the outer casing of this appliance is only cleaned with warm water with a little washing up liquid added After cleaning reconnect the equipment to the mains supply Defrosting of the ice maker compartment A certain amount of frost will always form around the ice maker compartment What to do if Important Defrost the ice maker compartment when the frost layer reaches a thickness of about 3 5 mm To remove the frost do these steps 1 Turn the Temperature regulator to the 0 setting and disconnect the mains plug from the mains socket 2 Empty the ice box 3 Leave the door of the appliance and ice maker compartment open 4 Defrosting usually takes several hours When finished pour defrost water gath ered out of the tray and wipe the surfaces dry 5 Insert the plug into the wall socket and turn the thermostat control to a medium setting Warning Never use sharp metal tools to scrape off frost from the evaporator as you could damage it Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer Periods of non operation When the appliance is not in use
11. for long peri ods take the following precautions 1 disconnect the appliance from electricity supply 2 remove all food defrost and clean the appliance and all ac cessories 4 leave the door doors open to prevent un pleasant smells Important If the cabinet will be kept on ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure www zanussi com Warning Before troubleshooting disconnect the mains plug from the mains socket Only a qualified electrician or competent person must do the troubleshooting that is not Important The appliance operates discontinuously so the stopping of compressor does not mean being no current That is why you must not touch the electrical parts of the in this manual appliance before breaking the circuit Important There are some sounds during normal use compressor refrigerant circulation Prolom Possible eause Solution The appliance is noisy The appliance does not operate The compressor operates continually Water flows on the rear plate of the refrigerator The temperature in the ap pliance is too low The temperature in the ap pliance is too high The temperature in the re frigerator is too high www zanussi com The appliance is not supported properly The appliance is switched off The mains plug is not connected to the mains socket correctly The appliance has no power There i
12. he plug out of the socket cut the connection cable as close to the appliance as you can and remove the door to prevent playing chil dren to suffer electric shock or to close themselves into it If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock latch on the door or lid be Care and cleaning 6 What to do if 2 6 Technical data 8 8 1 Installation Subject to change without notice sure to make that spring lock unusable be fore you discard the old appliance This will prevent it from becoming a death trap for a child General safety A Warning Keep ventilation openings in the appliance en closure or in the built in structure clear of ob struction The appliance is intended for keeping food stuff and or beverages in a normal household and similar applications such as staff kitchen areas in shops offices and other working environments farm houses and by clients in hotels mo tels and other residential type environ ments bed and breakfast type environments catering and similar non retail applications Do not use a mechanical device or any artifi cial means to speed up the thawing process Do not use other electrical appliances such as ice cream makers inside of refrigerating appliances unless they are approved for this purpose by the manufacturer Do not damage the refrigerant circuit The refrigerant isobut
13. ints for energy saving Do not open the door frequently or leave it open longer than absolutely necessary If the ambient temperature is high and the Temperature Regulator is set to low temper ature and the appliance is fully loaded the compressor may run continuously causing frost or ice on the evaporator If this happens set the Temperature Regulator toward warm er settings to allow automatic defrosting and so a saving in electricity consumption Hints for fresh food refrigeration To obtain the best performance do not store warm food or evaporating liq uids in the refrigerator do cover or wrap the food particularly if it has a strong flavour www zanussi com This compartment is suitable for making and storing ice cubes You can purchase the nee ded ice cube tray from a specialist shop Important Do not use metallic instruments to remove the ice cube tray from the freezer position food so that air can circulate freely around it Hints for refrigeration Useful hints Meat all types wrap in polythene bags and place on the glass shelf above the vegetable drawer For safety store in this way only one or two days at the most Cooked foods cold dishes etc these should be covered and may be placed on any shelf Fruit and vegetables these should be thor oughly cleaned and placed in the special draw er s provided Butter and cheese these should be placed in special airtight containers
14. o cut or stray strands of wire is present and the cord clamp E is secure over the outer sheath 5 Make sure the electricity supply voltage is the same as that indicated on the appli ance rating plate 6 Switch on the appliance The appliance is supplied with a 13 amp plug fitted B In the event of having to change the fuse in the plug supplied a 13 amp ASTA ap proved BS 1362 fuse must be used Warning A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that it is disposed of safely potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product 11 www zanussi com shop ES 8 i fN 212000171 A 452012
15. or wrapped in alumi nium foil or polythene bags to exclude as much air as possible Milk bottles these should have a cap and should be stored in the bottle rack on the door Bananas potatoes onions and garlic if not packed must not be kept in the refrigerator Hints for ice maker compartment Water ices if consumed immediately after removal from the ice maker compartment can possibly cause the skin to be freeze burnt Do not open the ice maker compartment door too often and do not leave open longer than necessary Care and cleaning Caution Unplug the appliance before carrying out any maintenance operation This appliance contains hydrocarbons in its cooling unit maintenance and recharg ing must therefore only be carried out by au thorized technicians Periodic cleaning The equipment has to be cleaned regularly clean the inside and accessories with luke warm water and some neutral soap regularly check the door seals and wipe clean to ensure they are clean and free from debris rinse and dry thoroughly Important Do not pull move or damage any pipes and or cables inside the cabinet Never use detergents abrasive powders highly perfumed cleaning products or wax polishes to clean the interior as this will damage the surface and leave a strong odour Clean the condenser black grill and the com pressor at the back of the appliance with a brush This operation will improve the perform anc
16. reely around the back of the cabinet To ensure best performance if the appliance is positioned below an overhanging wall unit the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm Ideally however the appliance should not be positioned below overhanging wall units Accu rate levelling is ensured by one or more adjust able feet at the base of the cabinet If the cabinet is placed in a corner and the side with the hinges facing the wall the distance be www zanussi com tween the wall and the cabinet must be at least 10 mm to allow the door to open enough so that the shelves can be removed ZN Warning It must be possible to disconnect the appliance from the mains power supply the plug must therefore be easily accessible after installation Door reversibility Important To carry out the following operations we suggest that this be made with another person that will keep a firm hold on the doors of the appliance during the operations To change the opening direction of the door do these steps 5 Remove the screw fixing the lower door 1 Remove the plug from the power sock et hinge and the other 2 Remove the top screw fixing the lower hinge cover door hinge and the foot Then remove the door hinge and the foot as shown in the Figure 6 Loosen the screw fixing the foot opposite the lower door hinge
17. s no voltage in the mains socket The temperature is not set correct ly The door is not closed correctly The door has been opened too fre quently The product temperature is too high The room temperature is too high During the automatic defrosting process frost defrosts on the rear plate The temperature regulator is not set correctly The temperature regulator is not set correctly The door is not closed correctly The product temperature is too high Many products are stored at the same time There is no cold air circulation in the appliance Check if the appliance stands stable all the four feet should be on the floor Switch on the appliance Connect the mains plug to the mains socket correctly Connect a different electrical appli ance to the mains socket Contact a qualified electrician Set a higher temperature Refer to Closing the door Do not keep the door open longer than necessary Let the product temperature de crease to room temperature before storage Decrease the room temperature This is correct Set a higher temperature Set a lower temperature Refer to Closing the door Let the product temperature de crease to room temperature before storage Store less products at the same time Make sure that there is cold air circu lation in the appliance problem IT CT There is too much frost The temperature regulator is not set correctly
Download Pdf Manuals
Related Search