Thank you for purchasing the Novopro RGBW LED SCRIM
Contents
1. 512 5 Controller Operation Press Fun to go befween these menus Press up or down to choose sound automatic amp DMX Press up or down to choose program between 1 17 Fast Slow 2 a oe EEJ DMX Address lt lt DMX512 gt o 001 Press Fun to go back Installation 1 After receiving the new LED Scrim unpack everything and check for any damage and that all accessories are as per the packing list 2 Carefully unfold the LED Scrim 3 Hang the LED Scrim on the booth with Velcro straps along the top and down both sides 4 Connect all the electrical parts such as power cables and control leads as per diagram 1 Signal Cable Connection There is a Signal cable with a 5pin plug at the back of each curtain Connect this Signal cable to the controller and then lock the nut on the plug If using several curtains then you need to connect the controllers together using 3pin shielded DMX Signal Cable 2 Power Cable Connection Before connecting the controller to the mains please make sure the voltage supply is AC90V 260V 50Hz 60Hz 3 Disassembly packing into the bag 1 Turn off amp disconnect power cable 2 Disconnect signal cable 3 Unfasten the Velcro straps around the LED Scrim 4 Carefully fold the LED Scrim store away IMPORTANT please ensure care is taken when folding packing the LED scrim to avoid damaging the connections and components V Program List 1 Program List2. Program List Do note that speed SP adjustment can be made when using the above programs SP01 fastest mode SP20 slowest mode 2 DMX Address Setting DMX Address Setting Based on the controller with 16 channels 2nd 17 1 16 5th 65 14 64 3rd 33 14 32 6th 81 1 80 3 DMX Channels Function DMX Channels Function Replacement of the LED s 1 Turn off the power supply 2 Disconnect the power cable and signal cable 3 Open the zipped fastener at the side of led curtain 4 Disconnect the wires between the LED S 5 Take out the LED holder from the cloth observing the amp marks 6 Get the replacement PCB board with LED s and connect to cloth observing correct polarity amp 7 Insert the lamp holder into the hole made on the cloth 8 Connect the power cable and signal cable and then turn on the power for testing 9 If the LED does not light then please double check all the connections 10 Close the zipped cloth again and all ready to go There are a full range of accessories and other related products available for the SDX booth please check out the Novopro website for more information All Novopro products are thoroughly QC checked prior to dispatch but should you have any queries or questions then please contact your place of purchase or contact us at info novopro co uk Novopro is a trade only supplier and only supply wholesale to trade resellers
3. Nnovopre Novopro products are designed and engineered in the UK and manufactured in China e Email info novopro co uk e Web www novopro co uk Due to continuous product developments amp improvements specifications and appearance are subject to change Copyright Novopro Ltd 2013 E amp OE
4. Page ll Thank you for purchasing the Novopro RGBW LED SCRIM novopre This user manual will help you to understand the features and operations of the LED curtain quickly and correctly so please spend a few minutes to read through this information Please ensure care is taken when folding packing and unpacking the LED scrim to avoid damaging the connections and components Due to continuous product developments please check for the latest updated version of this product manual at www novopro co uk Image above shown fitted to the Novopro SDX booth Manual V1 1 Straps ie i 120CM Ss Sa a E 290CM Please read the following Safety Notes as well as those in the User Manual carefully before connecting installing operating or maintaining this product The contents of this Novopro RGBW LED Scrim package are Ix LED Scrim 1x Controller 1x Power cable 2x Spare LED RED 2x Spare LED GREEN 2x Spare LED BLUE 2x Spare LED WHITE lx Novopro carry bag please ensure care is taken when folding packing the LED scrim to avoid damaging the connections and components Safety Notes 1 After receiving the Novopro LED Scrim please open the packing carton to check the goods and all other accessories are consistent with the packing list and in good condition If anything is found to be missing or damaged by transportation please contact your place of purchase as soon as possible 2 This LED Scrim is for i
5. ndoor use only 3 It should not be exposed to rain moisture water or any other liquids 4 The Scrim should be kept away from sources of heat or ignition to protect against fire 5 This item should be protected from shock vibration impact and dust in order to keep it in good working condition Also please take great care when folding unfolding cloth so that no undue strain is put on the internal wiring this will ensure trouble free operation for the life of the cloth 6 LED Scrim controller must be installed in a location with adequate ventilation to prevent overheating 7 The connection installation operation and maintenance of LED Scrim should only be attempted by competent person 8 Make sure no ventilation slots in the controller are blocked 9 Avoid walking on or pulling the LED Scrim with excessive force to keep the internal cables amp connections in order 10 Electrical connection must be carried out by qualified person 11 Make sure the voltage and frequency of the power supply match the power requirements of this device 12 Always connect this product to a grounded circuit to avoid the risk of electrocution 13 Do not connect LED Scrim to any dimmer circuitry 14 Make sure the power cord is not crimped or damaged 15 Never pull out the plug by pulling or tugging on the cord 16 Never operate this product with the covers removed 17 Always disconnect this product from the power supply before cleaning or attem
6. pting any maintenance work 18 Never suspend this product on any moving apparatus and always use the hanging mounting straps supplied 19 The maximum ambient temperature is 40 C Do not operate this product at higher temperatures 20 In case of any serious operation problem stop using this product immediately and contact your place of purchase Warning Any damages caused by the non observance of this manual or any unauthorised modification to this product will not be covered by the warranty Important Please observe the wiring colour coding of your country if connecting this product to the mains with anything other than the mains cable provided Note Make sure this product is connected to the earth properly Advantages of the Novopro RGBW LED Scrim SMD LEDs are small and bright They emit a pure colour and give long life Cloth material is soft smooth lightweight flexible amp can be folded The Fire retardant velvet material protects against fire Easy connection installation and transportation Claes IS 1 Product Description This Led Scrim is made with high brightness SMD LED s and use fire retardant velvet cloth The controller has 17 patterns and supports 8 channels of DMX The LED Scrim also comes equipped with a sound activation mode and the ability to choose and run your favourite program with a simple press of a button without the need for a DMX 512 controller The cloth has 2 layer
7. s of smooth velvet sewn together with wool There are many Velcro Straps fitted around the cloth using our industrial machines to enable it to be hung without the risk of the material tearing but care and attention must still be used Fitted with a standard UK mains plug just connect to the mains turn on the controller and choose and run your favourite program 2 Product Specification Voltage Input Voltage AC90V 240V 50 60Hz 25W 150W 3A 2A Output Voltage DC 12V 38A DC12V 12 5A Fuse 2A Power consumption 30W 150W Lamp SMD LEDs Life 50 000 hours DMX channel 8 ch Digital Screen in the controller Control system DMX Sound Active Auto run Number of programs 17 Led colour Red Green Blue White Cloth colour Black Overview 1 LED Scrim Note Grommets have been replaced with high quality Velcro straps on recent models Curtain Led Lamp bronmet able Overview 2 Controller novopr DMX Channel Display List La CH1 Dimmer PU S Cws Red Digital Display CH4 Green CH5 Blue CH6 Yellow ella hex koei Down UP Enter Fun ACBOV 240 50HZ 60H Powerin Switch DMX In Out Curtain Input PUWER IN DMX OUT DMX IN LED CURTAIN Overview 3 Controller Description tition eio or Menu need function you selected function you selected Overview 4 Menu Options PU Program 01 17 Program speed 01 fast through to 20 slow DMX Address 001
Download Pdf Manuals
Related Search