GT10 General Description
Contents
1. HOD HODW HOD2 HOL HODW2 HOLW Communication RS 232 RS 422 485 1ch RS 422 ch Transmission 115 200 57 600 38 400 19 200 9 600 speed 4 800bps Connector f PLC Connector terminal block 9 pins communication Open 1100 3309 Switched by terminating resistor selector switch At factory shipment 330Q Communication PC Transmission 115 200 57 600 38 400 19 200 9 600 communication 2 speed 4 800bps Connector MINI DIN 6 pins Female Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection For details of GOT multidrop connection refer to the following gt GOT1000 Series Connection Manual Mitsubishi Products for GT Works3 2 Project data upload download OS installation Transparent function Terminating resistor 1 4 Power Supply Specifications For details on power supply wiring such as the allowable cable size and tightening torque refer to the additional manual GT10 User s Manual Specifications Item GT1030 HOD HOD2 HODW HODW2 Input power supply 24VDC 10 15 5VDC 5 voltage ripple voltage 200mV or less supplied from the PLC Fuse built in not 2 2W 90mA 24VDC or less 1 1W 220mA 5VDC or 1 7W 70mA 24VDC or less 0 6W 120mA 5VDC less or less Inrush current 18A or less 26 4VDC 1ms Permissible instantaneous power Within 5ms E failure time 1 N2. 1D7MB9 transmitting data to GOT1000 series GT Designer3 Version Screen Design Manual For GOT1000 Series Functions 1 2 2 2 sold separately 1 GOT1000 Series Connection Manual Mitsubishi Products for GT Works3 sold separately _ Describes specifications and settings of the object functions used in GT Designer3 SH 080867ENG 1D7MC1 Describes system configurations of the connection method applicable to GOT1000 series and cable creation method SH 080868ENG 1D7MC2 Stored in the GT Works3 GT Designer3 in PDF format For details of a PLC to be connected refer to the PLC user s manual respectively Bundled Items Model Name Remark GT1030 HBD HWD GT1030 HBD2 HWD2 GT1030 HBL HWL GOT main unit The maintenance supplies below GT1030 HBDW HWDW are packed with the product GT1030 HBDW2 HWDW2 GT1030 HBLW HWLW Maintenance Supplies Quantity PLC Communication Connector 1 Panel Mounting Bracket with M4 x 20 screws 4 Panel Mounting Packing 1 GT10 General Description This manual 1 Explanation of the GOT model name GT1030 x x x x L Interface type for 2 RS 232 communication with PLC Blank RS 422 Backlight type W white red pink Blank green red orange Power type D 24VDC L 5VDC Panel color type B Black W White Display device type H STN monochrome High contrast Display color type 0 Monochrome black white Screen size type 3 4 5 GOT1000 series GT10 1 Specifications
3. e Manufactured at Mitsubishi Electric Corporation Himeji Works 840 Chiyoda machi Himeji Hyogo 670 8677 Japan e Authorized Representative in the European Community Mitsubishi Electric Europe B V Gothaer Str 8 40880 Ratingen Germany Requirement for Compliance with EMC directive The following products have shown compliance through direct testing to the identified standards and design analysis forming a technical construction file to the European Directive for Electromagnetic Compatibility 2004 108 EC when used as directed by the appropriate documentation Type Programmable Controller Open Type Equipment Standard Remark Compliance with all relevant aspects of the EMI i ae EN61131 2 2007 standard Radiated Emissions Programmable Compliance with all relevant aspects of the controllers Equipment ENE standard ESD RF electromagnetic field EFTB requirement and tests Surge RF conducted disturbances and Power frequency magnetic field For more details please contact the local Mitsubishi Electric sales site Model Code Describes the GT10 hardware relevant content such as part names external dimensions mounting power supply wiring specifications and introduction to option devices GT10 User s Manual sold separately JY997D24701 09R819 GT Designer3 Version Screen Design Manual For GOT1000 Series Fundamentals 1 2 2 2 sold separately 1 Describes methods of the GT Designer3 in
4. 1 1 General Specifications Specifications GT1030 HOD HOD2 HOLI HODW HODW2 HOLW Operat Display ine ambi 0 to 50 C Item ent tempera ia 0 to 55 C When mounted horizontally 0 to 50 C When ture Section mounted vertically Storage ambient 5 temperature ponte OO Operating Storage 10 to 90 RH non condensing The wet bulb temperature ambient humidity is 39 C or less Fre Accel Sweep quency eration Count Con 5 to A oats 380m to JIS Mi di 10 times Vibration resistance B3502 ent 8 4 to 2 each in IEC61131 and Z 2 Un de r a 1 75mm direc continu 9 42 tions ous 8 4 to Conforms to JIS B3502 IEC 61131 2 147m s2 11 ms Sine half wave pulse 3 times each in the X Y and Z directions Shock resistance Must be free of lamp black corrosive gas flammable gas or excessive amount of electro conductive dust particles and must be no direct sunlight Same as for saving 2000 m 6562 ft max Operating atmosphere Operating altitude Installation location Inside control panel Overvoltage ll or less category 2 Pollution degree s 2 or less Cooling method Self cooling Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude Om Oft Failure to observe this instruction may cause a malfunction When the air inside the control panel is purged by pressurization the surface sheet may be lifted by high pressure As a result the touch pa
5. 7 x H76 2 99 x D29 5 1 16 mm inch extemal uimensions Excluding mounting fixtures Horizontal format Panel cutting dimensions Weight Excluding mounting fixtures W137 5 39 x H66 2 59 mm inch Horizontal format 0 3kg 0 28kg 0 3kg 0 28kg Compa uble SONWANE GT Designer3 Version1 19V or later package 4 e Bright dots always lit and dark dots unlit may appear on a liquid crystal display panel It is impossible to completely avoid this symptom as the liquid crystal display comprises of a great number of display elements Flickers may be observed depending on the display color Please note that these dots appear due to its characteristic and are not caused by product defect Flickers and partial discoloration may be generated on the liquid crystal display panel due to the display contents or the contrast adjustment However please note that these phenomena appear due to its characteristic and are not caused by product defect There is a difference in the display brightness and the color tones between liquid crystal display panels When using multiple liquid crystal display panels please note that there is an individual difference between them A crosstalk shadow as an extension of the display may appear on the liquid crystal display panel Please note that it appears due to its characteristic When the display section is seen from the outside of the display angle the display color seems like it has changed Ple
6. GRAPHIC OPERATION TERMINAL GOTico0 GT1030 HBD2 HWD2 HBDW2 HWDW2 2 General notes on the use of the power cable The GT1030 HOD HOD2 HODW HODW2 unit demand that the cable for the power supply is 10m or less e When disposing of the product handle it as industrial waste e When disposing of batteries separate them from other wastes according to the local regulations For details of the battery directive in EU member states refer GOT User s Manual Associated Manuals The following manuals are relevant to this product When these loose manuals are required please consult with our local distributor chemical entering into the GOT TRANSPORTATION of the screws or the GOT and deteriorate the waterproof effect and oilproof effect due to distortion of the protective cover for oil GOT or panel When using the GOT in the environment of oil or chemicals use the protective cover for oil Failure to do so may cause failure or malfunction due to the oil or the registered trademarks or trademarks of each company Effective Apr 2012 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Safety Precaution Read these precautions before using Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual
7. Manual Mitsubishi Products for GT Works3 Cable jacket to remove 7mm 0 27 0 22 to 0 25 Nem SZS 0 4 x 2 5 Phoenix Contact Inc Tightening torque Recommended Tool Screwdriver This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe
8. are concerned with this product In this manual the safety precautions are ranked as DANGER and CAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous CAUTION conditions resulting in medium or slight personal injury or physical damage Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage DESIGN PRECAUTIONS lt SDANGER e Some failures of the GOT or cable may keep the outputs on or off An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction If a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the devi
9. phases can cause a unit failure or malfunction Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit STARTUP MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire e Do not touch the conductive and electronic parts of the unit directly Doing so can cause a unit malfunction or failure e The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault e When unplugging the cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault STARTUP MAINTENANCE PRECAUTIONS CAUTION e Do not drop or apply any impact to the battery If any impact has been applied discard the battery and never use it The battery may be damaged by the drop or impact Before touching the unit always touch grounded metal etc to discharge static electricity from human body etc Not doing so can cause the unit to fail malfunction Replace battery with GT11 50BAT by Mitsubishi electric Co only Use of another battery may present a risk of fire or explosion Dispose of used ba
10. regulation 1 General notes on the use of communication cables Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise Therefore when installing any communication cables care should always be taken with the routing and location of those cables The GOT units identified on the previous chapter are compliant with the EMC requirement when the following communication cables are used GOT Unit GT1030 HBD HWD HBL HWL HBDW HWDW HBLW HWLW Existing Cables GT10 C30R4 8P For Melsec FX series PLC GT10 C30R2 6P GT1030 HBD2 HWD2 HBDW2 HWDW2 For Melsec Q series PLC 2 General notes on the use of the power cable The GT1030 HOD HOD2 HODW HODW2 unit demand that the cable for the power supply is 10m or less Associated Manuals The following manuals are relevant to this product When these loose manuals are required please consult with our local distributor Model Code Describes the GT10 hardware relevant content such as part names external dimensions mounting power supply wiring specifications and introduction to option devices Manual name JY997D24701 09R819 GT10 User s Manual sold separately GT Designer3 Version Screen Design Manual For GOT1000 Series Fundamentals 1 2 2 2 sold separately 1 Describes methods of the GT Designer3 installation operation basic operation for drawing and SH 080866ENG
11. 2 in white Intensity adjustment 8 level adjustment Life Approx 50 000h Time for display intensity to become 1 5 at operating ambient temperature of 25 C LED with 3 available colors LED with 3 available colors green red orange white red pink Backlight status colors ON BLINK OFF control Adjustable screensaver activation time Setting the system information enables 2 PLC to control the backlight status Number of Maximum 50 keys screen Matrix resistive film touch touch keys panel Minimum 16 x 16 dots per key Simultaneous Touch pressing of panel two or GT1030 HOLW Backlight no replacement required Enable more areas 2 point press 1 million times or more operating force 0 98N max Flash memory ROM Internal for storing Project data 1 5M bytes or less OS Life Number of 100 000 times write times Memory SRAM Internal for storing alarm history recipe data and arve time action setting value GT11 50BAT lithium battery Magnesium maganese dioxide lithium primary battery Battery Backup Clock data alarm history and recipe data Approx 5 years Operating ambient temperature of 25 Buzzer output a buzzer that sounds when touch keys are pressed Single tone LONG SHORT OFF adjustable Environmental protective structure 4 Equivalent to IP67 JEM1030 front section W145 5
12. 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN Side JY99 7D25301R B TE A JAPANESE B ENGLISH MITSUBISHI e Be sure to shut off all phases of the external power supply used by the system before mounting or removing the GOT to from the panel GT1 030 H go D W H go D W 2 H go L W Not doing so can cause the unit to fail or malfunction GT10 General Description e When installing the battery wear an earth band etc to avoid the static electricity The static electricity can cause the unit to fail or malfunction Manual Number JY997D25301R MOUNTING PRECAUTIONS CAUTION This manual describes the specifications of the product Before use read this e Use the GOT in the environment that satisfies the general specifications described in this manual Not doing so can cause an electric shock fire malfunction or product damage or deterioration manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions When mounting the GOT to the control panel tighten the mounting screws in the specified torque range Undertightening can cause the GOT to drop short circuit or malfunction and deteriorate the waterproof effect and oilproof effect And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to th
13. 9 200 9 600 speed 4 800bps Connector PLC Connector terminal block 9 pins communication Open 1100 330Q Switched by terminating resistor selector switch At factory shipment 3309 Communication PC Transmission 115 200 57 600 38 400 19 200 9 600 communication 2 speed 4 800bps Connector i MINI DIN 6 pins Female 1 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection For details of GOT multidrop connection refer to the following GOT1000 Series Connection Manual Mitsubishi Products for GT Works3 2 Project data upload download OS installation Transparent function Terminating resistor 1 4 Power Supply Specifications For details on power supply wiring such as the allowable cable size and tightening torque refer to the additional manual GT10 User s Manual Specifications Item GT1030 HLUID HUD2 HODW HODW2 Input power supply 24VDC 10 15 5VDC 5 voltage ripple voltage 200mV or less supplied from the PLC Fuse built in not 2 2W 90mA 24VDC or less 1 1W 220mA 5VDC or 1 7W 70mA 24VDC or less 0 6W 120mA 5VDC less or less Inrush current 18A or less 26 4VDC 1ms Permissible instantaneous power Within 5ms failure time 1 Noise voltage 1000Vp p Noise width 1us by noise simulator of 30 to 100Hz noise frequency 500VAC for 1 minute Dielectric withst
14. JY997D25301R Side B Fa JAPANESE S E ENGLISH a MITSUBISHI GT1030 HOD W HOD W 2 HOL W GT10 General Description Manual Number JY997D25301R Changes for the Better GRAPHIC OPERATION TERMINAL GOTico0 This manual describes the specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Apr 2012 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Safety Precaution Read these precautions before using Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this product In this manual the safety precautions are ranked as DANGER and CAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous CAUTION conditions resul
15. Not doing so may cause an electric shock or malfunction Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the product Not doing so can cause a fire or failure Tighten the terminal screws of the GOT power supply section in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT Not doing so can cause a fire failure or malfunction WIRING PRECAUTIONS CAUTION e Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit TEST OPERATION PRECAUTIONS DANGER e Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter read through the manual carefully and make yourself familiar with the operation method During test operation never change the data of the devices which are used to perform significant operation for the system False output or malfunction can cause an accident S
16. S 0 4 x 2 5 Phoenix Contact Inc Tightening torque Recommended Tool Screwdriver This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system a MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7
17. SHORT OFF adjustable Environmental protective structure 4 Equivalent to IP67 JEM1030 front section W145 5 7 x H76 2 99 x D29 5 1 16 mm inch External dimensions Excluding mounting fixtures Horizontal format Panel cutting dimensions Weight Excluding mounting fixtures W137 5 39 x H66 2 59 mm inch Horizontal format 0 3kg 0 28kg 0 3kg 0 28kg Compatible gowang GT Designer3 Version1 19V or later package 1 e Bright dots always lit and dark dots unlit may appear on a liquid crystal display panel It is impossible to completely avoid this symptom as the liquid crystal display comprises of a great number of display elements Flickers may be observed depending on the display color Please note that these dots appear due to its characteristic and are not caused by product defect e Flickers and partial discoloration may be generated on the liquid crystal display panel due to the display contents or the contrast adjustment However please note that these phenomena appear due to its characteristic and are not caused by product defect e There is a difference in the display brightness and the color tones between liquid crystal display panels When using multiple liquid crystal display panels please note that there is an individual difference between them e A crosstalk shadow as an extension of the display may appear on the liquid crystal display panel Please note that it appears due to its characterist
18. TARTUP MAINTENANCE PRECAUTIONS DANGER e When power is on do not touch the terminals Doing so can cause an electric shock or malfunction e Connect the battery correctly Do not discharge disassemble heat short solder or throw the battery into the fire Incorrect handling may cause the battery to generate heat burst or take fire resulting in injuries or fires Before starting cleaning or terminal screw retightening always switch off the power externally in all phases Not switching the power off in all phases can cause a unit failure or malfunction Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit STARTUP MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire e Do not touch the conductive and electronic parts of the unit directly Doing so can cause a unit malfunction or failure e The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault e When unplugging the cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault PRECAUTIONS CA
19. UTION e When transporting lithium batteries make sure to treat them based on the transport regulations Refer to User s Manual for details of the regurated models Before transporting the GOT turn the GOT power on and check that the battery voltage status is normal on the Time setting amp display screen utilities screen In addition confirm that the adequate battery life remains on the rating plate Transporting the GOT with the low battery voltage or the battery the reached battery life may unstabilize the backup data unstable during transportation Make sure to transport the GOT main unit and or relevant unit s in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of this manual as they are precision devices Failure to do so may cause the unit to fail Check if the unit operates correctly after transportation Compliance with EC directive CE Marking This note does not guarantee that an entire mechanical module produced in accordance with the contents of this note will comply with the following standards Compliance to EMC directive for the entire mechanical module should be checked by the user manufacturer For more details please contact the local Mitsubishi Electric sales site Attention e This product is designed for use in industrial applications e Manufactured by Mitsubishi Electric Corporation 2 7 3 Marunouchi Chiyoda ku Tokyo 100 8310 Japan
20. and between the GOT s power voltage supply terminals and the GOT s grounding terminal GT1030 HUL HUOLW Power consumption At backlight off Noise immunity 10MQ or larger by insulation resistance tester between Insulation resistance the GOT s power supply terminals and the GOT s grounding terminal Class D grounding 100Q or less To be connected to the panel when grounding is not possible Grounding The GOT continues to operate even upon 5ms or shorter instantaneous power failure The GOT stops operating if there is extended power failure or voltage drop while it automatically resumes operation as soon as the power is restored 2 Wiring of connection cable The diagram below shows cable assignment for GOT port Cables GT10 COOOR4 8P GT10 COOOR4 2P GT10 COOOR2 6P GOT PLC PLC connection cable GT10 CLIDI OI R4 8P GT10 CLIOI O01 R4 25P GOT GOT GOT terminal terminal terminal block block block 24V 5V SDA roy Brown SDB Red Red RDA Orange Orange Yellow Yellow Green Green Black _Blue_ White r Purple BME Ssi User made cable is necessary depending on the PLC For the detail refer to GOT1000 Series Connection Manual Mitsubishi Products for GT Works3 Cable jacket to remove GT10 cOO0OR2 6P 7mm 0 27 0 22 to 0 25 Nem SZ
21. ase note that it is due to its characteristic Please note that the response time brightness and color of the liquid crystal display panel may vary depending on the usage environmental temperature Especially in the low temperature environment the display response becomes slow due to the characteristics of the STN liquid crystal Please check the display response in advance for using this product e Please note that the response in low temperatures tend to be slower as a characteristic of the liquid crystal display panel e When the same screen is displayed for a long time an incidental color or partial discoloration is generated on the screen due to heat damage and it may not disappear To prevent heat damage the screen saver function is effective For details of the screen saver function refer to the following GT10 User s Manual 2 For the details of system information refer to the following GT Designer3 Version1 Screen Design Manual 3 ROM in which new data can be written without deleting the written data 4 Note that this does not guarantee all users operation environment In addition the product may not be used in environments under exposition of oil or chemicals for a long period of time or in environments filled with oil mist 1 3 Communication Specifications Specifications HOD HODW HOD2 HOL HODW2 HOLW Communication RS 232 RS 422 485 1ch RS 422 1ch Transmission 115 200 57 600 38 400 1
22. ce that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction Incorrect operation of the touch switch s may lead to a serious accident if the GOT backlight is gone out When the GOT backlight goes out causes the monitor screen to appear blank while the input of the touch switch s remains active This may confuse an operator in thinking that the GOT is in screensaver mode who then tries to release the GOT from this mode by touching the display section which may cause a touch switch to operate e Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring and keep them a minimum of 100mm 3 94in apart Not doing so noise can cause a malfunction Do not press the GOT display section with a pointed material as a pen or driver Doing so can result in a damage or failure of the display section Before connecting to GOT turn ON the controller to enable the communication When the communication of controller is not available a communication error may occur in GOT e Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions Please make sure to ground FG terminal of the GOT power supply section by applying 100 or less which is used exclusively for the GOT
23. e Screen size type 3 4 5 GOT1000 series GT10 1 Specifications 1 1 General Specifications Specifications GT1030 HOD HOD2 HOLIHODW HODW2 HOLW Operat Display ing ambi 0 to 50 C Item ent tempera ria 0 to 55 C When mounted horizontally 0 to 50 C When ture section mounted vertically Storage ambient 5 temperature ees Operating Storage 10 to 90 RH non condensing The wet bulb temperature ambient humidity is 39 C or less Fre Accel Sweep quency eration Count Con forms to JIS B3502 Under 5 to 3 5mm tent 8 4 to 2 each in vibration 459Hz 9 8m s xX Y 5 to and Z Smau sake 17 reo tions ous 8 4 to Conforms to JIS B3502 IEC 61131 2 147m s2 11 ms Sine half wave pulse 3 times each in the X Y and Z directions Vibration resistance and 1EC61131 2 Shock resistance Must be free of lamp black corrosive gas flammable gas or excessive amount of electro conductive dust particles and must be no direct sunlight Same as for saving 2000 m 6562 ft max Operating atmosphere Operating altitude Installation location Inside control panel Overvoltage ll or less category 2 Pollution degree s 2 or less Cooling method Self cooling 1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude Om Oft Failure to observe this instruction may cause a malfunction When the air inside the control panel is purged by pressur
24. e end user Registration Overtightening can cause a drop short circuit or malfunction due to the damage The company name and the product name to be described in this manual are Notes for compliance to EMC regulation 1 General notes on the use of communication cables Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise Therefore when installing any communication cables care should always be taken with the routing and location of those cables The GOT units identified on the previous chapter are compliant with the EMC requirement when the following communication cables are used GOT Unit GT1030 HBD HWD HBL HWL HBDW HWDW HBLW HWLW STARTUP MAINTENANCE PRECAUTIONS CAUTION e Do not drop or apply any impact to the battery If any impact has been applied discard the battery and never use it The battery may be damaged by the drop or impact Before touching the unit always touch grounded metal etc to discharge static electricity from human body etc Changes for the Better Not doing so can cause the unit to fail malfunction Replace battery with GT11 50BAT by Mitsubishi electric Co only Use of another battery may present a risk of fire or explosion Dispose of used battery promptly Keep away from children Do not disassemble and do not dispose of in fire Existing Cables GT10 C30R4 8P For Melsec FX series PLC GT10 C30R2 6P For Melsec Q series PLC
25. een adjustment 16 level adjustment Intensity of i ECD an 200 cd m2 in green GT1030 HOLW 500 cd m2 in white Intensity adjustment 8 level adjustment Life Approx 50 000h Time for display intensity to become 1 5 at operating ambient temperature of 25 C LED with 3 available colors LED with 3 available colors green red orange white red pink Backlight status colors ON BLINK OFF control Adjustable screensaver activation time Setting the system information enables 2 PLC to control the backlight status Number of Maximum 50 keys screen Matrix resistive film touch touch keys panel Minimum 16 x 16 dots per key Simultaneous Touch pressing of panel two or Backlight no replacement required Enable more areas 2 point press 1 million times or more operating force 0 98N max Flash memory ROM Internal for storing Project data 1 5M bytes or less OS C drive 3 Life Number of 100 000 times write times f SRAM Internal for storing alarm history recipe data and D drive i f f time action setting value GT11 50BAT lithium battery Magnesium maganese dioxide lithium primary battery Batter y aay Clock data alarm history and recipe data Approx 5 years Operating ambient temperature of 25 Buzzer output a buzzer that sounds when touch keys are pressed Memory Single tone LONG
26. functions in the system afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN
27. ic e When the display section is seen from the outside of the display angle the display color seems like it has changed Please note that it is due to its characteristic Please note that the response time brightness and color of the liquid crystal display panel may vary depending on the usage environmental temperature Especially in the low temperature environment the display response becomes slow due to the characteristics of the STN liquid crystal Please check the display response in advance for using this product e Please note that the response in low temperatures tend to be slower as a characteristic of the liquid crystal display panel e When the same screen is displayed for a long time an incidental color or partial discoloration is generated on the screen due to heat damage and it may not disappear To prevent heat damage the screen saver function is effective For details of the screen saver function refer to the following GT10 User s Manual 2 For the details of system information refer to the following GT Designer3 Version1 Screen Design Manual 3 ROM in which new data can be written without deleting the written data 4 Note that this does not guarantee all users operation environment In addition the product may not be used in environments under exposition of oil or chemicals for a long period of time or in environments filled with oil mist 1 3 Communication Specifications Specifications
28. ization the surface sheet may be lifted by high pressure As a result the touch panel may be difficult to press and the sheet may be peeled off 2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the machinery within the premises Category Il applies to equipment for which electrical power is supplied from fixed facilities The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V 3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used In pollution degree 2 only non conductive pollution occurs but temporary conductivity may be produced due to condensation 1 2 Performance Specifications Specifications ee 288 x 96 dots Horizontal format W109 42 4 3 x H35 98 1 41 mm inch Horizontal Display size format Item GT1030 GT1030 rater GT1030 HOD HOD2 HOL HODW2 HOLW Type STN monochrome white black liquid crystal Specifications Item 2 A GT1030 GT1030 GT1030 DW HOD HOD2 HOL DW2 Display 16 dot standard font 36 characters x 6 lines 12 dot character standard font 48 characters x 8 lines Horizontal format Display Monochrome white black Display Left Right 30 degrees Top 20 degrees Bottom 30 angle degrees Horizontal format Display Contrast
29. n to appear blank while the input of the touch switch s remains active This may confuse an operator in thinking that the GOT is in screensaver mode who then tries to release the GOT from this mode by touching the display section which may cause a touch switch to operate e Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring and keep them a minimum of 100mm 3 94in apart Not doing so noise can cause a malfunction Do not press the GOT display section with a pointed material as a pen or driver Doing so can result in a damage or failure of the display section Before connecting to GOT turn ON the controller to enable the communication When the communication of controller is not available a communication error may occur in GOT MOUNTING PRECAUTIONS lt SDANGER e Be sure to shut off all phases of the external power supply used by the system before mounting or removing the GOT to from the panel Not doing so can cause the unit to fail or malfunction e When installing the battery wear an earth band etc to avoid the static electricity The static electricity can cause the unit to fail or malfunction MOUNTING PRECAUTIONS NCAUTION e Use the GOT in the environment that satisfies the general specifications described in this manual Not doing so can cause an electric shock fire malfunction or product damage or deterioration When mounting
30. nel may be difficult to press and the sheet may be peeled off 2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the machinery within the premises Category Il applies to equipment for which electrical power is supplied from fixed facilities The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V 3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used In pollution degree 2 only non conductive pollution occurs but temporary conductivity may be produced due to condensation 1 2 Performance Specifications Specifications Item GT1030 GT1030 Baar GT1030 HOD HOD2 HOL HODW2 HOLW STN monochrome white black liquid crystal eran 288 x 96 dots Horizontal format W109 42 4 3 x H35 98 1 41 mm inch Horizontal Display size format Specifications Item z 5 GT1030 GT1030 GT1030 DW HOD HOD2 HOL DW2 Display 16 dot standard font 36 characters x 6 lines 12 dot character standard font 48 characters x 8 lines Horizontal format Display f Monochrome white black Display Left Right 30 degrees Top 20 degrees Bottom 30 angle degrees Horizontal format Display f Contrast Pear adjustment 16 level adjustment Intensity of F LCD cal 200 cd m2 in green 500 cd m
31. oise voltage 1000Vp p Noise width 1ps by noise simulator of 30 to 100Hz noise frequency 500VAC for 1 minute Dielectric withstand between the GOT s power voltage supply terminals and the GOT s grounding terminal GT1030 HUL HUOLW Power consumption At backlight off Noise immunity 10MQ or larger by insulation resistance tester between the GOT s power supply terminals and the GOT s grounding terminal Insulation resistance Class D grounding 100Q or less To be connected to the panel when grounding is not possible Grounding The GOT continues to operate even upon 5ms or shorter instantaneous power failure The GOT stops operating if there is extended power failure or voltage drop while it automatically resumes operation as soon as the power is restored 2 Wiring of connection cable The diagram below shows cable assignment for GOT port Cables GT10 COOOR4 8P GT10 COOOR4 2P GT10 COOOR2 6P GOT PLC PLC connection cable GT10 COIO DI R4 8P GT10 CO O0 R4 25P GOT GOT GOT terminal terminal terminal block block block 24V 5V SDA_ f 1_ Brown SDB Red RDA r 1_ Orange RDB SG RSA RSB CSA CSB GT10 CO10 OR2 6P Yellow User made cable is necessary depending on the PLC For the detail refer to GOT1000 Series Connection
32. s and wire offcuts entering the GOT Not doing so can cause a fire failure or malfunction WIRING PRECAUTIONS NCAUTION e Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit TEST OPERATION PRECAUTIONS DANGER e Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter read through the manual carefully and make yourself familiar with the operation method During test operation never change the data of the devices which are used to perform significant operation for the system False output or malfunction can cause an accident STARTUP MAINTENANCE PRECAUTIONS DANGER e When power is on do not touch the terminals Doing so can cause an electric shock or malfunction e Connect the battery correctly Do not discharge disassemble heat short solder or throw the battery into the fire Incorrect handling may cause the battery to generate heat burst or take fire resulting in injuries or fires Before starting cleaning or terminal screw retightening always switch off the power externally in all phases Not switching the power off in all
33. stallation operation basic operation for drawing and SH 080866ENG 1D7MB9 transmitting data to GOT1000 series GT Designer3 Version Screen Design Manual For GOT1000 Series Functions 1 2 2 2 sold separately 1 GOT1000 Series Connection Manual Mitsubishi Products for GT Works3 sold separately 1 Describes specifications and settings of the object functions used in GT Designer3 SH 080867ENG 1D7MC1 Describes system configurations of the connection method applicable to GOT1000 series and cable creation method SH 080868ENG 1D7MC2 Stored in the GT Works3 GT Designer3 in PDF format For details of a PLC to be connected refer to the PLC user s manual respectively Bundled Items Model Name Remark GT1030 HBD HWD GT1030 HBD2 HWD2 GT1030 HBL HWL GOT main unit The maintenance supplies below GT1030 HBDW HWDW are packed with the product GT1030 HBDW2 HWDW2 GT1030 HBLW HWLW Maintenance Supplies Quantity PLC Communication Connector 1 Panel Mounting Bracket with M4 x 20 screws 4 Panel Mounting Packing 1 GT10 General Description This manual 1 Explanation of the GOT model name GT1030 x x x L Interface type for 2 RS 232 communication with PLC Blank RS 422 Backlight type W white red pink Blank green red orange Power type D 24VDC L 5VDC Panel color type B Black W White Display device type H STN monochrome High contrast Display color type 0 Monochrome black whit
34. the GOT to the control panel tighten the mounting screws in the specified torque range Undertightening can cause the GOT to drop short circuit or malfunction and deteriorate the waterproof effect and oilproof effect Overtightening can cause a drop short circuit or malfunction due to the damage of the screws or the GOT and deteriorate the waterproof effect and oilproof effect due to distortion of the protective cover for oil GOT or panel When using the GOT in the environment of oil or chemicals use the protective cover for oil Failure to do so may cause failure or malfunction due to the oil or chemical entering into the GOT e Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions Please make sure to ground FG terminal of the GOT power supply section by applying 100 or less which is used exclusively for the GOT Not doing so may cause an electric shock or malfunction Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the product Not doing so can cause a fire or failure Tighten the terminal screws of the GOT power supply section in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT Exercise care to avoid foreign matter such as chip
35. the following standards Compliance to EMC directive for the entire mechanical module should be checked by the user manufacturer For more details please contact the local Mitsubishi Electric sales site Attention e This product is designed for use in industrial applications e Manufactured by Mitsubishi Electric Corporation 2 7 3 Marunouchi Chiyoda ku Tokyo 100 8310 Japan e Manufactured at Mitsubishi Electric Corporation Himeji Works 840 Chiyoda machi Himeji Hyogo 670 8677 Japan e Authorized Representative in the European Community Mitsubishi Electric Europe B V Gothaer Str 8 40880 Ratingen Germany Requirement for Compliance with EMC directive The following products have shown compliance through direct testing to the identified standards and design analysis forming a technical construction file to the European Directive for Electromagnetic Compatibility 2004 108 EC when used as directed by the appropriate documentation Type Programmable Controller Open Type Equipment Standard Remark Compliance with all relevant aspects of the EMI i ae EN61131 2 2007 standard Radiated Emissions Programmable Compliance with all relevant aspects of the controllers Equipment ENE standard ESD RF electromagnetic field EFTB requirement and tests Surge RF conducted disturbances and Power frequency magnetic field For more details please contact the local Mitsubishi Electric sales site Notes for compliance to EMC
36. ting in medium or slight personal injury or physical damage Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage DESIGN PRECAUTIONS lt SDANGER e Some failures of the GOT or cable may keep the outputs on or off An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction If a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction Incorrect operation of the touch switch s may lead to a serious accident if the GOT backlight is gone out When the GOT backlight goes out causes the monitor scree
37. ttery promptly Keep away from children Do not disassemble and do not dispose of in fire e When disposing of the product handle it as industrial waste e When disposing of batteries separate them from other wastes according to the local regulations For details of the battery directive in EU member states refer GOT User s Manual TRANSPORTATION PRECAUTIONS CAUTION e When transporting lithium batteries make sure to treat them based on the transport regulations Refer to User s Manual for details of the regurated models Before transporting the GOT turn the GOT power on and check that the battery voltage status is normal on the Time setting amp display screen utilities screen In addition confirm that the adequate battery life remains on the rating plate Transporting the GOT with the low battery voltage or the battery the reached battery life may unstabilize the backup data unstable during transportation Make sure to transport the GOT main unit and or relevant unit s in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of this manual as they are precision devices Failure to do so may cause the unit to fail Check if the unit operates correctly after transportation Compliance with EC directive CE Marking This note does not guarantee that an entire mechanical module produced in accordance with the contents of this note will comply with
Download Pdf Manuals
Related Search