Product Manual
Contents
1. 1 TD 2 RD 2 2 TD Figure 4 Straight Through Cable Schematic Switch Switch 3 TD 3 RD 6 TD 6 RD 1 RD 1 TD 2 RD 2 TD Figure 5 Crossover Cable Schematic Cabling Twisted pair segments can be connected with unshielded twisted pair UTP or shielded twisted pair STP cable The cable must comply with the IEEE 802 3u 100Base TX standard e g CAT 5 CAT 5e or CAT 6 The cable between the equipment and the link partner switch hub workstation etc must be less than 100 meters 328 ft long Wiring the Power Inputs Please follow the steps below to wire the power cord which from the other compliant external DC power supplier 1 Insert the positive and negative wires into the PWR1 V V and PWR2 V V contacts on the terminal block connector as shown in Figure 6 V V V V Figure 6 Terminal Block Front View for Power1 amp Power2 Contact 2 Tighten the wire clamp screws which as shown in the Figure 7 for preventing the wires from loosing Figure 7 Terminal Block Top View Note gt Use Copper Conductors Only 60 75 C Tighten to 5 Ib in gt The wire gauge for the terminal block should be in the range between 12 24 AWG Power Restriction under 48VDC power IPES 0208CA 12V only can support one 48VDC power source If using two 48VDC power source IPES 0208CA 12V may cause damage 1 battery solution 1 negative power input site ground Rectifier 220VAC 48 VDC2. 75 C 40 F 167 F 5 95 non condensing 40 85 C 5 95 non condensing FCC Class A CE EN61000 4 2 ESD CE EN61000 4 3 RS CE EN 61000 4 4 EFT CE EN61000 4 5 Surge CE EN61000 4 6 CS CE EN61000 4 8 CE EN61000 4 11 CE EN61000 4 12 CE EN61000 6 2 CE EN61000 6 4 IEC60068 2 32 Shock IEC60068 2 27 Vibration IEC60068 2 6 Package Contents Please refer to the package contents list below to verify them against the checklist m IPES 0208CA 12V Industrial Switch with DIN Rail Bracket m User manual m Removable Terminal Block Hm Optional Wall mount Kit 2 wall mount bracket with screws Compare the contents of the industrial switch with the standard checklist above If any item is damaged or missing please contact the local dealer for service Safety Precaution Attention IF DC voltage is supplied by an external circuit please use a protection device on the power supply input Hardware Description In this paragraph the Industrial switch s hardware specs ports cabling information and wiring installation will be described Physical Dimension IPES 0208CA 12V Industrial Switch dimensions W x D x H is 74mm x 114mm x 152mm the detail dimensions as Figure 1 4 i H f i i i 3 a i f f f i 3 Lo f ij i A l u t f Hig i il e gt Hi ire i i i iq i J He IC i i f US j i j bitte i CJ 90 32 5 105 10 Figure 1 Mechanical Dimens
3. Fast Ethernet ports RJ 45 will auto sense for 10Base T or 100Base TX connections Auto MDI MDI X means that the switch can connect to another switch or workstation without changing straight through or crossover cabling Please refer to Table 2 for RJ 45 pin assignment Pin Number Assignment 1 Tx 2 Tx 3 Rx 6 Rx Table 2 RJ 45 Pin Assignment Note and signs represent the polarity of the wires that make up each wire pair All ports on this industrial switch supports automatic MDI MDI X operation users can use straight through cables See figures below for all network connections to PCs or Servers or to other switches hubs In straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable Table 3 shows the 10BASE T 100BASE TX MDI and MDI X port pin outs Pin MDI X Signal MDI Signal Receive Data plus RD Transmit Data plus TD Receive Data minus RD Transmit Data minus TD Transmit Data plus TD Receive Data plus RD OW N Transmit Data minus TD Receive Data minus RD Table 3 MDI MDI X Port Pin outs 10 The following figures show the cable schematic for straight through type Figure 4 and crossover type Figure 5 Switch Router PC 3 TD gt 3 RD 6 TD gt 6 RD 1 RD
4. refer to DIN Rail Mounting section for DIN Rail installation If the user wants to mount the Industrial switch on the wall then please refer to Wall Mounting section for wall mount plate installation 3 To hang the Industrial switch on the DIN Rail or wall please refer to the Mounting Installation section 4 Power on the Industrial switch Please refer to the Wiring the Power Inputs section for knowing the information about how to wire the power cord The power LED on the Industrial switch will light up Please refer to the LED Indicators section for indication of LED lights 5 Prepare the twisted pair straight through CAT 5 above cable for Ethernet connection 6 Insert one side of the RJ 45 cable into the Industrial switch Ethernet port and another side to the network device s Ethernet port e g Switch PC or Server The Ethernet port RJ 45 LED on the Industrial switch will light up when the cable is connected with the network device Please refer to the LED Indicators section for LED light indication 7 When all connections are set and LED lights all show in normal the installation is complete Network Application This segment provides the sample to help user have more actual idea of industrial switch application For a sample application of the industrial switch see the Figure 15 below Fiber Cable IPES 0208CA 12V Industrial Switch VOIP Phone IP Camera Wireless AP IEEE 802 3af Compliant Powered Devices F
5. Lantech IPES 0208CA 12V 8 10 100TX 2 10 100 1000T Dual Speed SFP Combo w 8x12V 24V 48V PoE at af Injector Industrial Switch User Manual V1 00 Jun 2013 Recommendation for Shielded network cables STP cables have additional shielding material that is used to reduce external interference The shield also reduces the emission at any point in the path of the cable Our recommendation is to deploy an STP network cable in demanding electrical environments Examples of demanding indoor environments are where the network cable is located in parallel with electrical mains supply cables or where large inductive loads such as motors or contactors are in close vicinity to the camera or its cable It is also mandatory to use an STP cable where the power device like IP camera is used outdoors or where the network cable is routed outdoors Aluminum Foil Shield Twisted Pair Wires FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particul
6. Rectifier 220VAC 48 VDC Rectifier 220VAC 48 VDC Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as the picture shows below Inserting the wires will detect the fault status including power failure or port link failure managed industrial switch only and from a Normally Close circuit Please refer to Figure 8 for the fault alarm contact and Figure 9 shows the application example for the fault alarm operation r PWR2 p Fajj PWR1 24V dc 1A Resistance Figure 8 Terminal Block Front View for Fault Alarm Contact Figure 9 Fault Alarm Application Example Note gt Use Copper Conductors Only 60 75 C Tighten to 5 Ib in gt The wire gauge for the terminal block should be in the range between 12 24 AWG Mounting Installation DIN Rail Mounting The DIN Rail bracket is screwed on the switch on the production line in the factory If the bracket is not screwed on the switch please refer to Figure 10 to screw it on the switch Follow the steps below to hang the industrial switch L Ch DIN Rail Bracket Figure 10 Rear side of the PoE Injectors Industrial Switch 1 Use the screws to screw the DIN Rail bracket on the rear side of the industrial switch 2 Toremove the bracket reverse the step 1 3 After the DIN Rail bracket is screwed on the rear side of the switch i
7. ar installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver Hm Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Hm Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Content ER FOAULOS diaos eee enhe a eee pA An 1 Technical Specification ccccccccccsssssssssseeeeeeeeeees 3 Package Contents ccccccccccssssssssseseeeeeeeeeeeeeeeeas 6 Salely PreGawtlOn css ae Sees 6 Hardware Description ccceeceeeeeeeeeeeeeeenseeeeeeenees 7 Physical DIMENSION cccceeeeeeeeeeeeeeeeeneeeeeeenaees 7 FORE GING oa mente ne eee teen esac et 8 TOD MIGW tyectectens eh ETERN 8 LED NACO a a seer enes REE 9 PORS a a Ea 10 CAIN ranon eae A 11 Wiring the Power Inputs u ssseeeveeerrerernnrnnnee 12 Wiring the Fault Alarm Contalt ce 14 Mounting Installation cesser 15 DIN Rail MOUNTING zis ar eas 15 Wall MOUMING ease seeder enue cmieraats ote er eee 17 Hardware I
8. igure 15 Network Application Troubleshooting m Verify that you are using the right power cord supplier adapter DC 12V 48V please don t use the power supplier adapter with a non compliant DC output voltage or it will burn the equipment EH Select the proper UTP STP cable to construct your network Please check that you are using the right cable Use unshielded twisted pair UTP or shield twisted pair STP cable for RJ 45 connections 100Q Category 3 4 or 5 cable for 10Mbps connections 100Q Category 5 cable for 100Mbps connections or 100Q Category 5e above cable for 1000Mbps Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet m Diagnosing LED Indicators To assist in identifying problems the Switch can be easily monitored through LED indicators on the front panel which describe common problems the user may encounter and where the user can find possible solutions m If the power indicator does not light on when the power cord is plugged in user may have a problem with the power cord Then check for loose power connections power losses or surges at power outlet If you still cannot resolve the problem contact the local dealer for assistance m If the Industrial switch LED indicators are normal and the connected cables are correct but the packets still cannot transmit Please check your system s Ethernet devices configuration or status 20
9. ions Front Panel The Front Panel of IPES 0208CA 12V Industrial Switch is shown below Figure 2 Figure 2 Front Panel of the POE Injectors Industrial Switch Top View The top view of IPES 0208CA 12V Industrial Switch has one terminal block connector of two DC power inputs and Relay circuit contact Please refer to Figure 3 for further information Figure 3 Top View of the POE Injectors Industrial Switch LED Indicators The diagnostic LEDs located on the front panel of the industrial switch provide real time information of system and operation status Table 1 provides the description of the LEDs status and their definitions for the switch LED Color Description Pi een On Power input 1 is active Off Power input 1 is inactive p3 ee On Power input 2 is active Off Power input 2 is inactive On Power input 1 or 2 has failed P Fail Red or Power input 1 and 2 are both functional or no power inputs PoE indicator On The port is supplying power to the powered device Port 1 8 ee Off No powered device attached or power supplying fails Green On Connected to network Flashing Networking is active LAN Port 1 8 a Off Not connected to network RJ 45 Green On Connected to network at speed of 100Mbps o Connected to network at speed of 10Mbps or not connected to network Table 1 LED Indication Definition Ports E RJ 45 ports The
10. nsert the top of the bracket into the rail as Figure 11 Figure 11 4 Then lightly pull down the bracket into the rail as shown in Figure 12 Figure 12 5 Check if the bracket is tightened on the rail or not 6 To remove the switch from the rail reverse steps above Wall Mounting optional Please refer to Figure 13 and follow the steps below to mount the industrial switch with wall mount bracket and the detail dimension of the bracket as Figure 14 1 Remove the DIN Rail bracket from the switch loose the screws to remove it 2 Place the wall mount bracket on the top side and bottom side of the switch 3 4 Use the hook holes at the corners of the wall mount bracket to hang the industrial Use the screws to screw the wall mount bracket on the switch switch on the wall To remove the wall mount bracket reverse steps above Figure 13 Wall Mount Bracket Installation 2 25 11 S 3 e J i J 9 00 _ 30 00 15 00 Figure 14 Wall Mount Bracket Dimensions 17 Hardware Installation In this paragraph we are going to explain how to install IPES 0208CA 12V Industrial Switch and the installation points to be attended to it Installation Steps 1 Unpack the Industrial switch packing 2 Check if the DIN Rail bracket is screwed on the Industrial switch or not If the bracket is not screwed on the Industrial switch please
11. nstallation screen 18 Installation Steps secerek irao neaten EE Ea a 18 Network Application scenerne 19 Troubleshooting scener eee EDEL 20 Introduction IPES 0208CA 12V Industrial Switch is a cost effective solution which meets the high reliability requirements demanded by industrial applications and also supports to operate in the wide temperature 40 C 75 C environments E model Besides the equipment supports 12V 24V 48V DC power input and provides the PoE function with 48VDC output for any kinds of powered devices to receive power as well as data over an RJ 45 cable Features m System Interface Performance gt VV VV V VV WV RJ 45 port support Auto MDI MDI X Function Embedded 8 port booster PoE injector function SFP Mini GBIC supports 100 1000 Dual Mode IEEE 802 3af at Standards Back plane Switching Fabric 5 6Gbps 1Mbits Packet Buffer 8K MAC Address Table Support Operating Temperature 20 C 60 C 40 C 75 C E models DC 12V 24V 48V Redundant Power Input Hm Operating Temperature gt gt Standard Temperature 20 C 60 C Extended Temperature 40 C 75 C E Case Installation gt gt gt IP 30 Protection Installation in a Pollution Degree 2 environment DIN Rail and Wall Mount Design Provides EFT protection 3 000 VDC for power line EH Supports 6 000 VDC Ethernet ESD protection Technical Specification Communications Compatibility LAN Switch Architecture I
12. nterface Connectors LED Indicators PoE Power Output Pin Assignment Power Power Consumption The technical specifications of IPES 0208CA 12V Industrial Switch are listed as follows IEEE 802 3 802 3u 802 3ab 802 3z 802 3x 802 3af at 10 100Base T Back plane Switching Fabric 5 6Gbps Packet throughput ability Full Duplex 8 3Mpps 64bytes 10 100TX 8 x RJ 45 10 100 1000T Mini GBIC Combo 2 x RJ 45 2 x 100 1000 SFP sockets Unit Power1 Power2 P Fail PoE Ethernet port Link Active Speed Per port 48 Vpc 15 4 Watts 802 3af 30Watts at RJ 45 port 1 gt 8 support IEEE 802 3af at End point Alternative A mode Positive VCC RJ 45 pin 1 2 Negative VCC RJ 45 pin 3 6 Data 1 2 3 6 10 Watts Max POE Power Budget 240 Watts 48V input 120W 24V input 9OW 12V Power Input Fault Output Mechanism Dimensions WxHxD Enclosure Mounting Protection ESD Ethernet Surge EFT for power Power Reverse Overload current protection Environment Operating Temperature Operating Humidity Storage Temperature Storage Humidity Certifications EMC Free Fall External Power Supply DC 9 56V Redundant power D9V DC 56V and connective removable terminal block 1 Relay Output 74mm W x 114mm D x 152mm H IP 30 Metal shell with solid mounting kits DIN Rail and Wall Mount Design 6 000 Vpc 3 000 Voc Yes Yes Standard 20 C 60 C 4 F 140 F Extended 40 C
Download Pdf Manuals
Related Search