COMPACTOR - KitchenAid
Contents
1. cloth and a mild detergent in warm water Rinse and dry thoroughly with a soft cloth 5 If the drawer side was removed slide it back into the tilted position 6 Press the lever action lock or Side Lock Latch down while pushing the drawer side to the upright position 7 Latch the drawer side by pushing up the lever action lock or Side Lock Latch 11 Cleaning Inside the Cabinet Cleaning the Ram NOTE You may want to wear gloves since there may be bits of glass in the cabinet 1 Pull the drawer out until it stops NOTE Look to see how the drawer rollers move in the tracks It will be easier to replace the drawer after you have finished cleaning 2 Lift the front of the drawer to clear the stops 3 Grasp the drawer on the sides and pull it out the rest of the way Set the drawer down gently 4 Vacuum the inside of the cabinet Liquid spills or wet trash should be cleaned up by hand or by using a vacuum designed to pick up liquids 5 Wash the inside of the cabinet with a clean sponge or soft cloth and a mild detergent in warm water Rinse and dry thoroughly with a soft cloth 6 To replace the drawer grasp it by the sides and insert the rollers onto the tracks 7 Lift the front of the drawer and push it in fully past the stops 12 NOTE You may want to wear gloves since there may be bits of glass on the ram cover 1 Wipe glass particles off of the ram cover with a cloth or paper tow2. without a trim kit The panel should be 1 2 13 mm minimum thickness 63 5 cm 15 38 1 cm Installation 1 Remove the mounting screws attaching the foot pedal to the compactor Remove the foot pedal A Mounting screws B Foot pedal 2 Remove the mounting screws attaching the toe guard to the compactor Remove the toe guard 3 Remove the mounting screws attaching the decorative panel to the compactor Remove the decorative panel and discard the mounting screws 4 Align the bottom of the custom panel with the bottom of the drawer front 5 Secure the panel from the back using four 8 x 1 wood screws as shown 6 Attach a 15 x 88 1 cm x 13 mm quarter round filler along the top of the drawer front using glue or screws 7 Reinstall the toe guard using the existing screws and 1 2 washer Then reinstall the foot pedal E Washer F Toe guard screw C Panel screw locations D Toe guard A Custom panel B 15 x 38 1 cm x 13 mm quarter round filler COMPACTOR USE How Your Compactor Works The compacting ram is the part of the compactor which compresses the trash The compacting ram does not go to the bottom of the drawer You will not see compacting of trash the first few times you load the compactor NOTE The compactor drawer should be more than 1 2 full before the compactor can begin to compress the load You may hear a noise when glass breaks Strong gl
3. chance of injury and tell you what can happen if the instructions are not followed State of California Proposition 65 Warnings WARNING This product contains one or more chemicals known to the State of California to cause cancer WARNING This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm IMPORTANT SAFETY INSTRUCTIONS WARNING When using an electrical appliance basic precautions should always be followed including the following m Read all instructions before using the compactor m Do not compact toxic or volatile flammable material such as oily rags and insect sprays Do not compact lighted m Close supervision is necessary when used by or near UPS cigarettes cigars or other hot or burning items Do not children Do not allow to be used as a toy or to run unattended at any time Lock Key Switch when not in use overload the compactor and store key out of reach of children m Do not take apart the compactor Incorrect reassembly can Do not touch moving parts cause electric shock when subsequently used Do not operate with a damaged cord set plug motor or E Handle a loaded trash bag with care Sharp objects can after damage in any manner Have the compactor pierce the bag and cause injury Do not overload trash bag examined repaired or adjusted by an authorized with heavy material such as glass serviceperson m This compactor is intended for h
4. if it is installed in an inaccessible location or is not installed in accordance with published installation instructions gt BP MONO DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE Outside the 50 United States and Canada this warranty does not apply Contact your authorized KitchenAid dealer to determine if another warranty applies If you need service first see the Troubleshooting section of the Use amp Care Guide After checking Troubleshooting additional help can be found by checking the Assistance or Service section or by calling KitchenAid In the U S A call 1 800 422 1230 In Canada call 1 800 807 6777 9 05 Keep this book and your sales slip together for future 7 Dealer name re
5. the compactor cabinet and put compactor on its side on top of the corner posts rear of the compactor A Cord clip 13 Remove the shipping base from the bottom of the compactor A A Leveling legs B Shipping base Location Requirements Product Dimensions Cutout Dimensions 34 min 87 cm 24 min 61 cm 18 min 45 7 cm 15 min 38 7 cm A Grounded electrical outlet must be a minimum of 3 7 6 cm away from surrounding cabinets or nearby walls as shown It can be placed either to the left or the right side of the product Clearance Dimensions l A Leave 6 15 2 cm of clearance space to the right side of the compactor in order to remove the compactor bags B Leave 23 58 4 cm of clearance in front of the compactor in order to fully open or remove the compactor drawer Electrical Requirements AWARNING 4 Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Recommended Grounding Method This compactor is for use on a single phase 115 volt 60 Hz AC only 15 or 20 amp fused and properly grounded circuit and is equipped with a grounding plug as shown below It is recommended that a separate circuit serving only this appliance be provi
6. 30 DAY LIMITED WARRANTY ON THE CHARCOAL FILTER AND AIR FRESHENER For thirty days from the date of purchase when the compactor is installed operated and maintained according to instructions attached to or furnished with the product KitchenAid will provide a replacement filter or air freshener if the original filter or air freshener fails due to defects in materials or workmanship ITEMS KITCHENAID WILL NOT PAY FOR 1 Service calls to correct the installation of your major appliance to instruct you how to use your major appliance to replace or repair house fuses or to correct house wiring or plumbing 2 Service calls to repair or replace appliance light bulbs or water filters Those consumable parts are excluded from warranty coverage 3 Repairs when your major appliance is used for other than normal single family household use Damage resulting from accident alteration misuse abuse fire flood acts of God improper installation installation not in accordance with electrical or plumbing codes or use of products not approved by KitchenAid Replacement parts or repair labor costs for units operated outside the United States or Canada Pickup and delivery This major appliance is designed to be repaired in the home Repairs to parts or systems resulting from unauthorized modifications made to the appliance Expenses for travel and transportation for product service in remote locations The removal and reinstallation of your appliance
7. KitchenAid COMPACTOR For questions about features operation performance parts accessories or service call 1 800 422 1230 or visit our website at www kitchenaid com In Canada for assistance installation or service call 1 800 807 6777 or visit our website at www KitchenAid ca Table of GONTENUS wii ciis se cescassdenccaciviceceiacuusecsecusasunauecvsedecuususdavessugeaceocads svavdscnebiunacaeeuueeuases gt 2 AK E 9872216B TABLE OF CONTENTS COMPACTOR SAFETY csscessseeseeessersnersesseessesseeneerseeeneeesneneees 2 Using the Air Filter or Freshener 2 ccccccceececeeeeeeeeeeeteeeeneeeeenes 9 INSTALLATION INSTRUCTIONS ccccccocecceccececceseececcocsececsececreceereeee 3 Removing a Filled Bag e csscescsseesseeeseeeeeeeenseeeeseenseeneetenes 10 Unpacking wit tenets aston teeta E i 3 Installing a New Bag ssssssssssssssstrrrrttsstrrresssssssssnnnntttnnnnrtttteeet 10 Location Requirements iiris 4 COMPACTOR CARE ssssssunsensunenrnnnnnnunnunnunnnnnnnnnnnnnnnnannnnnnnnnnnnnnnn nn 11 Electrical Requirements Changing the Air Filter or Freshener 2 cesecceeeeeeeeeeeeeees 11 Freestanding and Undercounter Installation eeeeseeeeeeee 5 CIGANING sadieeiiceived nian tacieiaei tei iaienee ital ites bias 11 Changing the Custom Panel scsscsscseetsssesesesessesesseseastensees 7 TROUBLESHOOTING s ceseseeseessseeeseseseeseseeeseeneneeeeneeneeaeens 13 COMPACTOR SE vsccesc
8. ass bottles may not break at all The trash in a full compactor bag will be about 1 4 the size of its original bulk Load bulky trash bottles and cans in the center of the drawer Bottles or cans not placed in the center may become caught between the ram and the drawer The Drawer Monitor Switch then senses a misload and causes the ram to return to the up position without compacting Loading IMPORTANT Do not push items down into compactor with hands or feet NOTE You will not see compacting of trash the first few times you load the compactor The compactor drawer should be about 12 full before the compactor can begin to compress the load 1 Open the drawer Lift and pull the handle or press the toe bar to open the drawer NOTE Pressing the toe bar opens the container only 3 to 6 7 6 cm to 15 2 cm depending on the load N 2 Place trash in compactor m Wrap or cover wet or messy trash m Do not compact items that may develop offensive odors such as raw meat fish grapefruit rinds disposable diapers or personal hygiene items m Load bottles or cans on their sides in the center of the drawer Do not load bottles in an upright position 3 Close the drawer WHISPER QUIET Plus System The WHISPER QUIET Plus system helps to maintain a quiet home environment during compactor operation NOTE The contents of the trash may affect the noise level of your compactor See Com
9. binet opening 10 Using 2 8 18 x 4 mounting screws provided in conversion kit fasten the retaining brackets provided in conversion kit to the countertop with the mounting screws Countertop Mounting A A Countertop B Retaining bracket provided in conversion kit C Mounting screw provided in conversion kit NOTE If retaining brackets cannot be attached to the underside of countertop attach mounting clips provided in conversion kit to retaining brackets Fasten compactor to kitchen cabinet face with mounting screws through the mounting clips Cabinet face Mounting A A Mounting clip provided in conversion kit B Kitchen cabinet C Retaining bracket provided in conversion kit D Mounting screw provided in conversion kit 11 Grasp sides of compactor drawer and place bottom of drawer into tracks 12 Lift at the handle so drawer will go over drawer stops 13 Close drawer 14 Check to see whether drawer opens freely If the toe plate rubs against floor see Adjusting the Toe Plate for further instructions Adjusting the Toe Plate If the toe plate rubs the floor covering the toe plate clearance may be changed as follows 1 Mark on each side of the toe plate the amount of toe plate that rubs the floor covering 2 Remove the drawer from the unit See Step 3 in the Unpacking section 3 Use a ruler and a pencil or chalk to draw a line between the marks o
10. ctecctccecestcccececdecet ctctebsccienscusedeteliestaceeaseescecee 8 ASSISTANCE OR SERVICE sssssssseceessessessessesseesesseessesenseneenennes 14 How Your Compactor WOmKS ccccscsscsscssseseessssessssesseseseesanees 8 In the U S A cccccccccsssseceessnseeesseeeesesseeeessneeeeesssneeesssneseeesssneeeeeses 14 LOAGING EAA hated daa Aeldhaie tle 9 Tg gh 0 f erp es eR a 14 WHISPER QUIET Plus System 0 ceceee eee eset eeeeeteeeeeees 9 ACCESSONIES cccsccesscseecsseeseecseesseessecseecsseseeeseessecsaeceaeeneeeaeesaes 14 Starting the Compactor sssssccccsseessseeeeessneeeeeeeeesennnneeeeeseeneens 9 WARRANTY simian a et rea 15 Using Solid Locked Cycle s sesesssseseeneneeesnenesnensnnrnensrssnenernrernee 9 COMPACTOR SAFETY Your safety and the safety of others are very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean A You can be killed or seriously injured if you don t immediately DANG ER follow instructions You can be killed or seriously injured if you don t follow A WARN i N e instructions All safety messages will tell you what the potential hazard is tell you how to reduce the
11. ded This compactor must be grounded while in use to reduce the risk of electric shock The compactor is equipped with a three conductor cord and 3 prong grounding type plug to fit the proper grounding type receptacle The green or green and yellow conductor in the cord is the grounding wire NOTE Do not connect the green or green and yellow wire to a live terminal Freestanding and Undercounter Installation NOTE Proper installation is your responsibility Make sure you have everything necessary for correct installation It is the personal responsibility and obligation of the customer to contact a qualified installer to assure that electrical installation meets all national and local codes and ordinances Tools Needed Gather the required tools and parts before starting installation m Level m Pliers m Phillips screwdriver m 3 6 hex head wrench m Tape measure m Scissors m Flat blade screwdriver m Utility knife IMPORTANT m Do not grasp control panel to move compactor m Slide compactor onto cardboard or hardboard before moving compactor across floor to avoid floor covering damage m Do not allow the rear frame of the compactor to touch the floor covering when lifting or moving compactor Freestanding Installation 1 Use pliers to lower leveling legs away from cabinet 2 With the drawer still removed from the compactor cabinet place level inside on the floor of the cabinet Check that the compactor is l
12. e the Key Knob and store it out of children s reach Using the Air Filter or Freshener The fan powered charcoal air filter absorbs and minimizes odor The degree of odor in the compactor depends on the type of trash placed in it The length of time before the filter needs to be replaced varies with the type of trash compacted Under normal use the filter should be replaced once or twice per year To Use the Filter 1 Press ON on the charcoal Air Filter control The fan creates air movement in the compactor for odor removal NOTE The charcoal air filter works even when the Key Knob is in the OFF position IMPORTANT The air freshener will work with or without the fan 2 Press OFF on the charcoal Air Filter control to turn off the fan Air Filter S N S N Off On NALA N oA Removing a Filled Bag When the trash is compacted to the top of the drawer remove the bag If the bag is too heavy compact less trash before emptying it in the future IMPORTANT Do not push items down into compactor with hands or feet 1 Pull the drawer completely open 2 Remove top of bag from bag retainer buttons Pull up all 4 bag cuffs Close bag with twist tie provided 4 Lift out bag 10 Installing a New Bag Do not use any kind of bag other than those designed especially for use in your compactor Order replacement compactor bags through your local dealer or by calling the toll free number on the cover or in
13. els 2 Remove foods with a clean sponge or soft cloth and a mild detergent in warm water Rinse and dry thoroughly with a soft cloth Cleaning Before a Vacation If you will be away for more than a couple of days remove the compactor bag Remove the Key Knob or Key Switch and store it out of children s reach TROUBLESHOOTING Try the solutions suggested here first in order to avoid the cost of an unnecessary service call Trash is not compacting The drawer won t open Is the drawer less than half full Drawer must be more than half full before trash is compacted Your compactor won t operate Is the power supply cord unplugged Plug into a grounded 3 prong outlet Has a household fuse blown or has a circuit breaker tripped Replace the fuse or reset the circuit breaker If the problem continues call an electrician Is the drawer completely closed Close the drawer firmly and start the compactor again Is the Key Knob turned all the way to START Turn the Key Knob Key Switch fully to START and release on some models See Starting the Compactor Did you press ON before pressing START Press ON before pressing START on some models See Starting the Compactor Is the ram all the way up Drawer will open only when ram is fully raised To raise the ram on models with a Key Knob or Key Switch Turn the Key Knob Key Switch to START and release See Starting the Compact
14. er rear wheel A Wheel bracket assembly C Locating stud B Compactor cabinet D Self tapping screw pivot Use pliers to lower leveling legs away from compactor cabinet Adjust legs so there will be a 14 3 mm to 1 4 6 4 mm space between the top of the compactor and the top of the kitchen cabinet opening Stand the compactor upright Remove the plastic plugs from the compactor cabinet top Move the compactor close to its final location Plug into a grounded 3 prong outlet Determine whether you want the compactor cabinet or drawer front flush with the kitchen cabinet face Using 2 8 18 x 6 mounting screws provided in conversion kit attach the retaining brackets provided in conversion kit to the compactor cabinet top as needed See Accessories NOTE Installation hardware is not provided with full cabinet models See Accessories for ordering conversion kit m If the compactor cabinet face is to be flush with the kitchen cabinet face place retaining bracket mounting screws through 1 m f the compactor drawer front is to be flush with the kitchen cabinet face place retaining bracket mounting screws through 3 m If the compactor is to be midway between 1 and 3 place the retaining bracket mounting screws through 2 A Countertop B Retaining bracket provided in conversion kit 9 Slowly lift the front slightly and roll compactor into the kitchen ca
15. evel from front to back and side to side 3 Adjust the leveling legs until the compactor is level Move the compactor close to its final location Plug into a grounded 3 prong outlet Slowly move compactor into its final position Check that compactor is still level Repeat Step 1 if necessary 8 Grasp sides of compactor drawer and place bottom of drawer into tracks 9 Lift at the handle so drawer will go over drawer stops 10 Close drawer 11 Check to see whether drawer opens freely If the toe plate rubs against floor see Adjusting the Toe Plate for further instructions NOTA Undercounter Installation NOTE Installation hardware is not provided See Accessories for ordering conversion kit 1 SNOOP Measure the height of your kitchen cabinet opening The top of the compactor should be at least Ys 3 mm from the top of the kitchen cabinet opening The rear wheels are preset for a kitchen cabinet opening height of 341 87 cm position 1 To adjust for other kitchen cabinet opening heights m Loosen self tapping screw enough to clear stud from hole in position 1 m Move the rear wheel and stud to position 2 or 3 as needed for your kitchen cabinet opening measurement Position 2 34 to 34 6 87 to 87 5 cm Position 3 34 6 to 345 87 5 to 88 cm NOTE To level the unit in position 3 you may need to add shims under the front leveling legs m Tighten screw m Repeat for oth
16. ference You must provide proof of purchase or installation date for in warranty service Address Write down the following information about your major appliance to better help you obtain assistance or service if you ever need it Phone number You will need to know your complete model number and serial Model b number You can find this information on the model and serial ocer HUMbEr number label located on the product Serialn mber Purchase date 15 11 13 9872216B 2013 KitchenAid Used under license in Canada All rights reserved Printed in U S A
17. n each side of toe plate 4 Use scissors or utility knife to cut toe plate along line 5 Replace drawer If toe plate still rubs floor covering repeat steps 1 to 4 Changing the Custom Panel Custom Panel with Handle Model KUCPO02IR Dimensions Use these dimensions drawings to create a custom panel for use without a trim kit The panel should be 1 2 to 13 mm to 16 mm thick NOTE A thicker panel may need rounded front corners and a cutout for access to the handle 23136 60 5 cm e 15 ____ 38 1 cm Installation 1 Remove the mounting screws attaching the foot pedal to the compactor Remove the foot pedal SD A A Mounting screws B Foot pedal 2 Remove the mounting screws attaching the toe guard to the compactor Remove the toe guard 3 Remove the mounting screws attaching the decorative panel to the compactor Remove the decorative panel and discard the mounting screws 4 Align the bottom of the custom panel with the bottom of the drawer front 5 Secure the panel from the back using four 8 x 1 wood screws as shown 6 Reinstall the toe guard using the existing screws and 1 2 washer Then reinstall the foot pedal 9 A Handle C Panel screw locations E Washer B Custom panel D Toe guard F Toe guard screw Custom Panel without Handle for all C and S models Dimensions Use these dimension drawings to create a custom panel for use
18. nty and provide after warranty service anywhere in Canada For Further Assistance If you need further assistance you can write to KitchenAid Canada with any questions or concerns at Customer eXperience Centre KitchenAid Canada 200 6750 Century Ave Mississauga Ontario L5N 0B7 Please include a daytime phone number in your correspondence Accessories To ensure the proper functioning of your compactor use KITCHENAID replacement parts only To order replacement parts or accessories call 1 800 462 3819 and ask for the appropriate part number listed below or contact your authorized KitchenAid dealer In Canada call 1 800 807 6777 Replacement Parts m Replacement Bags Call for Part Number m Charcoal Air Filters Part Number 4151750 14 m Air Fresheners scent Fresh Green Apple Part Number 9872166GA Lavender Part Number 9872166L Lemon Grove Part Number 9872166G m Conversion Kit for Freestanding Unit Undercounter Installation Only Part Number 9870118 KITCHENAID COMPACTOR WARRANTY ONE YEAR LIMITED WARRANTY For one year from the date of purchase when this major appliance is operated and maintained according to instructions attached to or furnished with the product KitchenAid or KitchenAid Canada hereafter KitchenAid will pay for factory specified parts and repair labor to correct defects in materials or workmanship Service must be provided by a KitchenAid designated service company
19. or To raise the ram on models with push button controls Press OFF and then press ON See Starting the Compactor Is the Solid Cycle engaged Drawer remains LOCKED until you reset by lifting the foot pedal up There is not enough compaction or force m Do you use the compacting cycle frequently enough Compacting works best when only a few items are loaded Bottles don t break m How often do you notice this Bottles will not break every time The thickness of the bottle s glass and the content of the trash load below it may keep the bottle from breaking 13 ASSISTANCE OR SERVICE Before calling for assistance or service please check Troubleshooting It may save you the cost of a service call If you still need help follow the instructions below When calling please know the purchase date and the complete model and serial number of your appliance This information will help us to better respond to your request If you need replacement parts If you need to order replacement parts we recommend that you use only factory specified parts These factory specified parts will fit right and work right because they are made with the same precision used to build every new KITCHENAID appliance To locate factory specified parts in your area call us or your nearest KitchenAid designated service center In the U S A Call the KitchenAid Customer eXperience Center toll free 1 800 422 1230 or visit o
20. ousehold use only Use only for intended use as described in this manual Do not use other than manufacturer s recommended SAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS Installer Leave Use and Care Guide with the homeowner Homeowner Keep Use and Care Guide for future reference and for local electrical inspector s use if required Unpacking 6 Place the 2 corner posts from the carton on the floor near the AWARNING compactor 7 Open the compactor drawer and remove any shipping Excessive Weight Hazard materials or other items from the drawer Use two or more people to move and install compactor NOTE Do not remove the compactor bag Failure to do so can result in back or other injury 8 Grasp the handle and raise the front of drawer until it clears the drawer stops 9 Grasp sides of drawer and lift drawer out of compactor IMFORTANT 10 Place the drawer on the 2 corner posts m Do not grasp console to move compactor m Begin in the room where the compactor will be located 1 Remove compactor from shipping carton 2 Remove all packaging materials such as tape and shipping pads 3 Use a mild detergent and warm water to remove waxy residue caused by shipping material 4 Dry thoroughly with a soft cloth For more information see Cleaning 5 Be sure the power cord is attached to the cord clip on the 11 Place the other 2 corner posts on the floor to the side of the compactor A 12 Grasp the sides of
21. pactor Use Starting the Compactor 1 Press NORMAL UNLOCKED on the Compact Control Turn the Key Knob to START and then release it OFF NoN Compact SA N ns START Solid Normal Locked Unlocked N47 4 2 The compactor stops after completing the cycle NOTE When the compacting cycle is done turn the Key Knob to OFF Remove the Key Knob and store it out of children s reach Using Solid Locked Cycle The Solid Locked cycle extends the use of a bag by putting constant pressure on the trash to keep it from springing back Regular use of the Solid Locked cycle can increase bag capacity up to 25 percent During the Solid Locked cycle the ram will stay in the down position for extra compacting While the Solid Locked cycle is operating an indicator shows on the control panel The drawer is locked and cannot be opened when the ram is down For best results use the Solid Locked cycle for at least 30 minutes at a time To Use Solid Locked Cycle 1 Press SOLID LOCKED on the Compactor Control Turn the Key Knob to START and then release the Key Knob NOTE The indicator on the control panel shows when the Solid Locked cycle is in use OFF SON Compact Solid Normal START Locked Unlocked SNI NA 2 After 30 minutes or more turn the Key Knob to START to raise the compacting ram OR press NORMAL UNLOCKED NOTE When the compacting cycle is done turn the Key Knob to OFF Remov
22. the Assistance or Service section IMPORTANT Before installing a new bag be sure m The drawer side is securely locked m The container is clean and free of debris 1 Place folded bag into the drawer Open bag and pull top edges over the drawer top 2 Lock bag in place by pulling the 4 prepunched holes over the bag retainer buttons Holes will expand over the buttons without damaging the bag 3 Press inside of bag against the drawer bottom sides and corners for a smooth fit COMPACTOR CARE Your new compactor is designed to give you many years of dependable service However there are a few things you are expected to do in order to properly maintain your compactor This section will tell you how to clean and care for your compactor Changing the Air Filter or Freshener It is recommended that you use either the charcoal air filter or the air freshener in the filter compartment The solid air freshener system is an alternative to the air filter and is designed to control odors that might develop in the trash To order the correct replacement charcoal filters or air fresheners call the toll free number listed on the cover or in the Assistance or Service section 1 Insert fingertips in the air filter cover and pull until the side tabs release Then lift the cover to release the bottom tabs 2 Remove the air filter by pulling the top edge of the filter The filter should pull out easily Throw away
23. ur website at www kitchenaid com Our Consultants Provide Assistance With Features and specifications on our full line of appliances Installation information Use and maintenance procedures Accessory and repair parts sales Specialized customer assistance Spanish speaking hearing impaired limited vision etc m Referrals to local dealers repair parts distributors and service companies KitchenAid designated service technicians are trained to fulfill the product warranty and provide after warranty service anywhere in the United States To locate the KitchenAid designated service company in your area you can also look in your telephone directory Yellow Pages For Further Assistance If you need further assistance you can write to KitchenAid with any questions or concerns at KitchenAid Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor MI 49022 2692 Please include a daytime phone number in your correspondence In Canada Call the KitchenAid Canada Customer eXperience Centre toll free 1 800 807 6777 or visit our website at www kitchenaid ca Our Consultants Provide Assistance With m Features and specifications on our full line of appliances m Use and maintenance procedures m Accessory and repair parts sales E Referrals to local dealers repair parts distributors and service companies KitchenAid Canada designated service technicians are trained to fulfill the product warra
24. used filter OR Remove the air freshener by simply lifting out of the filter compartment Throw away used freshener 3 To replace air filter push the replacement filter into place OR To replace the air freshener place the replacement in the filter compartment 4 Insert the bottom tabs of the air filter cover and push in until the side tabs snap into place Cleaning Before cleaning the compactor turn the Key Knob or Key Switch to the OFF amp LOCK position and remove it NOTE Any services other than those outlined in this section should be performed by a designated service representative Cleaning Exterior Surfaces 1 Wash exterior surfaces including stainless steel with a clean sponge or soft cloth and a mild detergent in warm water Do not use abrasive or harsh cleaners Rinse and dry thoroughly with a soft cloth 2 Wipe up spills right away Some foods can damage the finish if left on the compactor surface Cleaning Inside the Drawer NOTE You may want to wear gloves since there may be bits of glass in the drawer 1 Remove the bag See Removing a Filled Bag 2 Press down on the lever action lock or Side Lock latch 3 Hold the lever action lock down and tilt the side of the drawer out until the lock clears the drawer front NOTE If desired the drawer side can be removed by tilting it up then lifting it out 4 Wash the interior of the drawer with a clean sponge or soft
Download Pdf Manuals
Related Search