victron energy
Contents
1. WARNING THIS COMMUNICATION PORT IS FOR FUTURE OPTIONS 2 7 Connecting the load Before you connect your appliance s to the inverter output always check it s maximum power consumption Do not connect appliances to the inverter needing more than the nominal power rating of the inverter continuously Some appliances like motors or pumps may draw high inrush currents during startup In this kind of situations it is possible that the startup current exceedes the overcurrent trip level of the inverter In this case the output voltage will quickly decrease to limit the output current of the inverter If this overcurrent trip level is continuously exceeded the inverter will shut down and restart within 18 seconds In this case it is advisable to disconnect this appliance from the inverter since it requires to much power to be driven by this inverter Note that at higher ambient temperature levels the overload capacity of the inverter is reduced Besides indicating the type of error the red LED on the inverter also functions as an overload indicator When heavy loads are switched on this LED will quickly be activated due to the inrush current of the load If the ERROR OVERLOAD LED stays on for 6 seconds the inverter will shut down and jumps into the overload error mode see chapter 3 1 NEVER CONNECT THE INVERTER S OUTPUT TO THE AC DISTRIBUTION GRID LIKE YOUR HOUSEHOLD AC WALL OUTLET IT WILL DAMAGE THE INVERTER CAUTION WHEN CONNECTI2. Inverter is not working AC Present LED OFF Possible cause Remedy A Eo Power switch in OFF 0 position Push the power switch either in the ON I or in the ASB Il position Poor contact between the inverter s battery Clean battery terminals or inverter wire wires and the battery terminals contacts Tighten battery terminal screws Blown inverter fuse Replace damaged fuse with the correct type Make sure you disconnect the battery before changing the fuse See chapter 5 2 for further information regarding fuse replacement Very poor battery condition Replace battery or charge it first Remote ON OFF switch link removed and or Make sure that there is a closed circuit between remote switch in OFF position the two Remote ON OFF switch contacts to start the inverter PROBLEM Battery voltage too low or too high error keeps on appearing AAA en ee a A Possible cause Remedy A AE A Poor connection or inadequate wiring between When extending the battery wires of the inverter battery and inverter resulting in too much make sure you use the correct wire gauge voltage drop 1 5 times larger than the fixed battery wires It s not advisable to extend the battery wires to more than 3 meters General failure in your electrical system in case Check your electrical system or consult an of no direct battery connection electrical engineer to check it for you PROBLEM Overloaded or shorted output error keeps on ap
3. This acoustic message will start at a battery voltage close to the shutdown voltage The inverter also shuts down when too high input ripple voltage is detected reducing the inverter s lifetime High input ripple voltage values are mostly caused by using too small batteries and or extending the DC cables too much or with insufficient wire gauge When the inverter shuts down due to too high input ripple voltage indicated by four blinks per second it must be restarted manually THE PHOENIX 12 1000 MUST BE CONNECTED ONLY TO A 12V BATTERY SYSTEM The inverter will not operate from a 6V battery and will be damaged when connected to battery voltages higher than 16V CAUTION 2 4 1 Using power supplies instead of batteries It is not recommended to power the inverter directly from a DC power supply when full inverter performance is required Most power supplies are not able to supply the huge surge currents required by the inverter and usually generate a too high ripple voltage causing the inverter s high ripple protection to trip 2 5 Connection to the battery The Phoenix 12 1000 is equipped with two 25 mm wires with a length of 1 5 meters Unless it is absolutely necessary Victron Energy advises not to extend the battery wires Extending the battery wires may increase system losses and can cause inverter malfunctioning like tripping the input ripple protection circuit If it is unavoidable to extend these wires use a wire gauge of at le
4. and lighting 2 5 1 General precautions about working with batteries 1 Working in vicinity of a lead acid battery is dangerous Batteries can generate explosive gases during operation Never smoke or allow a spark or flame in vicinity of a battery Provide sufficient ventilation around the battery Wear eye and clothing protection Avoid touching eyes while working near batteries Wash your hands when done If battery acid contacts skin or clothing wash immediately with soap and water If acid enters eye immediately flood eye with running cold water for at least 15 minutes and get medical attention immediately Be careful when using metal tools in vicinity of batteries Dropping a metal tool onto a battery might cause a shorted battery and an explosion Remove personal metal items such as rings bracelets necklaces and watches when working with a battery A battery can produce a short circuit current high enough to weld a ring or the like to metal causing severe burns victron energy AO 2 6 The serial communication port The Phoenix 12 1000 inverter is equipped with an RS485 serial communications port for future use The communication port wiring is designed to work with a standard RJ45 terminated Ethernet compatible patch cable Maximum recommended cable length is approx 50 meters DO NOT CONNECT THE INVERTER S SERIAL COMMUNICATION PORT TO AN ETHERNET NETWORK OR TO ANY OTHER NON COMPATIBLE NETWORKS
5. from direct sunlight or heat producing equipment additional cooling by an external fan Note Don t turn off the inverter when it s operating in an Inverter temperature too high Cooling down error The inverter needs this error time to cool down PROBLEM Too high input ripple voltage error keeps on appearing Possible cause Remedy Input voltage ripple is too large caused by poor Reduce load enlarge battery capacity make inverter installation sure the DC wires are not extended too long lt 3 meters and that sufficient wire gauge is used gt 1 5x the standard equipped wire gauge check eventual generators dynamos high ripple chargers which are connected to the same DC system PROBLEM Inverter jumps between continuous mode and pulsed ASB mode all the time Possible cause Remedy Connected load is not compensated or the ratio Connect an additional load to the output between inrush current and continuous current is too large If none of the above remedies will help solve the problem you encounter it s best to contact your local Victron Energy distributor for further help and or possible repair of your inverter Do not try to repair the inverter yourself there are dangerous high voltages present inside Attempts to repair and or modify the inverter will directly void your warranty WARRANTY Victron Energy warrants this inverter to be free from defects in workmanship or materials for 24 month
6. A max 50 meters The main on off switch on the inverter frontpanel always overrides the remote on off switch So in order to use the remote switch the main on off switch must be in the ON or Automatic standby ASB position Maximum recommended length of the remote switch wires are 50 meters Use professional quality wiring for these connections to avoid easy wire damage The recommended wire gauge is 0 2mm AWG24 or greater MAKE SURE THAT WHEN INSTALLING THE REMOTE SWITCH THE BATTERY IS NOT CONNECTED YET CAUTION victron energy Oy 2 3 The ground terminal In order to complete the grounding circuit of your AC system the inverter s housing can be connected to ground by using the dedicated ground screw See the figure below for the location of the ground screw Use a wire gauge of at least 2 5mm AWG13 for the ground wire O 4 1 chassis ground screw 2 4 Battery requirements For correct operation the battery voltage should be between 11V and 14 4V The recommended battery capacity is gt 300 Ah This capacity can be halved for short time inverter usage not requiring more than nominal output power The DC input current at nominal output power is approx 88A The inverter shuts down when the battery voltage is below approx 10 5V and above approx 16V When the battery voltage is too low or too high first the inverter will generate one beep per second to inform you about a possible inverter shut down
7. AS FALLEN TO AN ACCEPTABLE LEVEL AGAIN WARNING IN A TOO HIGH INPUT RIPPLE VOLTAGE ERROR THE INVERTER WILL NOT AUTOMATICALLY RESTART BUT NEEDS TO BE RESET MANUALLY Manual reset is neccesary to notify the user that something is wrong with the inverter s installation too small battery too long or thin DC wires etc 3 2 Acoustic messages To warn you before the inverter might shut down it is equipped with an acoustic alarm This can be very useful when you are for example working with a computer that runs from the inverter The inverter will warn you just before it is going to shut down so you can save or finish your work before you lose power There are three kinds of acoustic messages depending on the cause of possible inverter shutdown These messages are related to the red LED blinking sequences mentioned previously Message 1 One beep per second The battery voltage has reached a too low or too high level If the battery voltage respectively decreases or increases any further the inverter shuts down Message 2 Two beeps per second The inverter will shut down soon due to an overloaded output Note that with heavy overloads the alarm will not sound due to rapid inverter shut down Normally the inverter warns approx 10 seconds before shutdown Message 3 Three beeps per second The inverter will shut down when it s temperature rises another two degrees Celsius victron energy Oy 3 3 Troubleshooting guide PROBLEM
8. MC Generic Immunity Standard Signed R Vader U Authority Managing Director Date 27 November 2002 victron energy MO 36 Stock number Dealer Victron Energy B V The Netherlands General phone Customer support desk General and Service fax Sales fax E mail Internet site Doc no Date 31 0 36 535 97 00 31 0 36 535 97 77 31 0 36 531 16 66 31 0 36 535 97 40 sales victronenergy com http www victronenergy com ISM010037000 REV00 doc 27 11 2002 victron energy y
9. NG MORE THAN ONE APPLIANCE TO THE INVERTER IN COMBINATION WITH A COMPUTER NOTE THAT IF ONE OF THE APPLIANCES STARTS UP IT CAN CAUSE YOUR COMPUTER TO REBOOT DUE TO A SUDDEN VOLTAGE DROP WARNING victron energy Oy 2 8 Turning on the inverter When all the above requirements are checked and satisfied and all connections are made it s time to turn on your Phoenix inverter by pushing the power switch in the I position After a short two tone beep the sinewave shaped output voltage gently rises until 230V 50Hz 1 or 115V 60Hz 1 is reached ready to power your appliances When the inverter is not supplying power to an appliance for an extended time it is recommended to use the inverter in Automatic Standby ASB mode to reduce the inverter s own power draw In this case the power switch must be pushed in the II position In ASB mode the inverter will generate a testpulse on it s output once per second to check that there is a load applied When the ASB mode is activated by generating a reversed two tone beep the blue AC Present LED will flash continuously for 4 seconds while the inverter outputs a continuous 230V or 115V sinewave After this 4 seconds the continuous output will change to a pulsed output Every time this pulse is generated the blue LED is activated too in order to indicate that there s a lethal AC voltage present at the output When a load is connected to the inverter output or switched on drawing
10. ast 1 5 times larger than the ones supplied with the inverter Maximum recommended battery wire length is approx 3 meters Make sure that the joint between the original wires and the extension wires is made solid and with very low electrical resistance in mind victron energy AO BATTERY TERMINALS Recommended battery fuse size is 150A 200A TO AVOID FIRE HAZARDS CAUSED BY DAMAGED DC WIRES ALWAYS PLACE A BATTERY SYSTEM FUSE AS CLOSE AS POSSIBLE TO YOUR CAUTION BATTERY THE RED WIRE MUST BE CONNECTED TO THE POSITIVE TERMINAL AND THE BLACK WIRE TO THE NEGATIVE TERMINAL OF THE Reverse polarity connection of the battery wires can damage the inverter Damage caused by reversed polarity is not covered by the warranty Make sure CAUTION the powerswitch is in the OFF 0 position before connecting the battery IF THE INVERTER IS CONNECTED TO THE BATTERY WITH INCORRECT POLARITY THE DC FUSE WILL BLOW To replace the internal DC fuse see chapter 5 2 for further information If the fuse blows again even with the correct polarity applied the inverter is damaged and must be returned for service WARNING DO NOT CONNECT OTHER DC POWERED EQUIPMENT TO THE SAME BATTERY THAT POWERS YOUR INVERTER It s possible that the performance of some equipment that isn t properly WARNING protected against ripple current may be affected when connected to the same battery that powers the inverter This dosn t apply for batterychargers
11. ated externally on the product Whenever it is likely that the earth protection has been damaged the product must be turned off and secured against unintended operation please contact qualified service staff Ensure that the in leads are fitted with fuses and circuit breakers Never replace a safety component with a different type Consult the manual to determine the correct component Before applying power ensure that the available power source matches the configuration settings of the product as described in the manual Ensure that the equipment is used under the correct ambient conditions Never operate the product in a wet or dusty environment Ensure there is adequate free space for ventilation around the product and check that the ventilation vents are not blocked Ensure that the required voltage does not exceed the product s capacity Transport and Storage Ensure that the mains power and battery leads have been disconnected before storing or transporting the product No liability can be accepted for any transport damage if the equipment is shipped in non original packaging Store the product in a dry environment the storage temperature must be between 20 C en 60 C Consult the battery manufacturer s manual in respect of transport storage charging recharging and disposal of the battery victron energy MO TABLE OF CONTENTS INTRODUCTION INSTALLATION F 2 1 Placement of the inverter in 2 2 Using the Remote O
12. iarise yourself with the safety features and instructions by first reading the documentation supplied with this product before using the equipment This product has been designed and tested in accordance with international standards The equipment must be used exclusively for the purpose for which it was designed WARNING ELECTRIC SHOCK HAZARD The product is used in conjunction with a permanent energy source battery Input and or output terminals may still be dangerously energised even when the equipment is switched off Always switch off the A C supply and the battery before carrying out maintenance or servicing the product The product has no internal user serviceable components Do not remove the front plate or operate the product if any panels have been removed All servicing must be undertaken by qualified personnel Never use the product where there is a risk of gas or dust explosions Consult the battery manufacturer s information to ascertain that the product is intended for use in conjunction with the battery Always comply with the battery manufacturer s safety instructions WARNING Do not lift heavy loads without assistance Installation Read the installation instructions in the user manual before switching on the equipment This is a Safety Class product supplied with a protective earthing terminal Uninterruptable protective earthing must be provided at the AC input and or output terminals An additional earth point is loc
13. inverter abuse like reverse polarity of battery connections Both fuses can be accessed by removing the cover of the enclosure as described below BEFORE OPENING THE INVERTER TO REPLACE A FUSE ALWAYS DISCONNECT THE BATTERY FROM THE INVERTER FOLLOWED BY DISCHARGING THE INTERNAL CAPACITORS BY PUSHING THE POWER SWITCH OF THE DISCONNECTED INVERTER IN THE l POSITION FOR 10 SECONDS CAUTION 1 Unscrew the 8 top cover screws 4 on each side see picture below to lift the top cover enabling access to the internal fuses To make removing the top cover easier it is advisable to slightly unscrew the remaining left and right screws on one side of the inverter Remove these four screws at both Gently lift the cover upwards ends of the inverter enclosure 2 Now the top side of the main PCB is visible as well as the location of the two fuses See the figure below for the fuse locations UBA AC Fuse DC Fuse ra OEA victron energy 15 Oy FUSE TYPES Model DC fuse Phoenix 12 1000 5x20mm 10Amp 250V slow blow Pudenz type no 156 5611 6121 125Amp automotive strip fuse 3 The AC side fuse can be replaced by turning and pushing the plastic cap counter clockwise until the cap releases and can be pulled out The DC fuse can be replaced by unscrewing the two nuts Make sure the new fuse is inserted in exactly the same position as the
14. ld Operating temperature range ambient voltage and high input ripple voltage blinking sequences of the red LED battery voltage and high input ripple voltage Other indications Overload red LED AC Present blue LED DC input connection AC output connection Enclosure body size I x h x w Protection class Inverter weight e inverter complies with the following standards EN50081 1 Generic Emissions Standard EN50082 1 Generic Immunity Standard EN60950 Safety Standard EN60742 Transformer Standard Note the given specifications are subject to change without notice Measured with resistive load Non linear load crest factor 3 1 Cont output at 25 C 7 Cont output power at 25 C Cont output power at 40 C 7 Peak power Z Output voltage Output waveform Input voltage O O omia f ooo Range static oo Range 1000VA Efficiency Maximum IN Prom Automatic standby threshold gt 17 victron energy MO 6 2 Declaration of conformity CE IMPORTER Victron Energy ADDRESS De Paal 35 1351 JG Almere Haven The Netherlands Declares that the following products PRODUCT TYPE DC TO AC SINEWAVE INVERTER MODELS Phoenix 12 1000 Conforms to the requirements of the following Directive of the European Union EMC Directive 89 336 EEC The above products are in conformity with the following harmonized standards EN50081 1 1994 EMC Generic Emissions Standard EN50082 1 1997 E
15. more than approx 10W the inverter jumps to the continuous mode immediately delivering power to the load When the load is disconnected again or switched off the blue LED starts flashing for 4 seconds and the inverter jumps back to the pulsed output ASB mode This way the inverter automatically jumps to a low power sleep mode when there is no power demand on the output Note that some loads like TV video equipment with standby mode and alarm clocks need continuous power so that the ASB mode can not be used With some small non compensated loads it is possible that the inverter jumps from continuous output to pulsed output and vice versa all the time In this case you have to connect a small additional load to the AC output IF THE INVERTER JUMPED INTO AN ERROR MODE SEE CHAPTER 3 1 DUE TO AN OVERLOAD OR SHORT CIRCUIT THE INVERTER WILL AUTOMATICALLY RESTART AFTER ABOUT 18 SECONDS In case of a high temperature error the inverter will automatically restart after it has reached an acceptable temperature Right before the inverter will restart it will warn you with a short beep WARNING NEVER SERVICE THE AC CONNECTIONS WHEN THE INVERTER IS STILL RUNNING IN AN ERROR MODE THE LARGE BUILT IN ELECTROLYTIC CAPACITORS CAN HOLD SIGNIFICANT DC VOLTAGE WHEN THE BATTERIES ARE DISCONNECTED To avoid sparks or short inverter operation it is advisable to switch on the inverter for 10 seconds after battery disconnection before you transpo
16. n Off function 2 3 The ground terminal 8 2 4 Battery requirements 2 4 1 Using power supplies instead of batteries 2 5 Connection to the battery 2 5 1 General precautions about working with batteries 2 6 The serial communication port nd os 2 7 Connecting the load 2 8 Turning on the inverter SELF DIAGNOSIS SYSTEM TROUBLESHOOTING 3 1 The blink sequence table 3 2 Acoustical messages 3 3 Troubleshooting guideline WARRANTY MAINTENANCE FUSE REPLACEMENT 5 1 Maintenance 5 2 Replacing fuses TECHNICAL SPECIFICATIONS DECLARATION OF CONFORMITY 6 1 Phoenix 12 1000 6 2 Declaration of conformity victron energy MO 1 INTRODUCTION Thank you for choosing a Phoenix DC to AC inverter The Phoenix inverter series are one of the most sophisticated inverters available today With high reliability efficiency and sine quality as our most important design goals the Phoenix inverter series is developed to serve you with safe and trouble free operation for years Your Phoenix inverter features an advanced micro processor control system with a MOSFET power stage and a low loss toroidal transformer This toroidal transformer in combination with well over dimensioned power components ensures very reliable operation so that extreme overload conditions like startup of compressors or pumps can be handled safely To get optimum feedback from your inverter while operating a built in diagnosis system will warn you of sta
17. ng requirements a Avoid any contact with water on the inverter Do not expose the inverter to rain or moisture b Do not place the unit in direct sunlight or other high temperature environments Ambient air temperature should be between 0 C and 40 C humidity lt 95 non condensing Note that in some extreme situations the inverter s case temperature can exceed 70 C victron energy AO c Do not obstruct the airflow around the inverter Leave at least 10 centimeters clearance around the inverter Do not place items on or over the inverter while it s operating When the inverter is running too hot it will shut down until a safe temperature level is reached to restart the inverter d Never use the inverter in locations where there is gas or explosion danger for example directly on top of batteries or close to volatile liquids e Do not expose the inverter to dusty environments 2 2 Using the Remote On Off function This Phoenix inverter offers the possibility to connect an external remote on off SPST switch min 6OVDC 1A The two wires of the external switch must be connected to the terminals blocks as indicated below Before connecting an external switch the factory installed link wire must be removed first Make sure that when installing the remote switch the battery is NOT connected yet 1 2 s m installed ink il a po
18. pearing Possible cause Remedy Inverter is overloaded Make sure that the total power rating of the connected equipment is lower than the nominal inverter power rating Connected equipment features a bad power reduce the required power consumption of the factor cose at sinusoidal currents load Please note that for example a computer load features a bad power factor which causes a reduction of the maximum output power of the inverter by approx 20 Connected equipment causes a short circuit at Make sure that the connected equipment is not the inverter s output broken or malfunctioning Check if the AC power cord between the inverter and the connected equipment is ok Any physical damage on the power cord can produce a short circuit Be careful in this kind of situations Connected equipment produces a too large Try to power up connected equipment inrush current successively and not simultaneously Or The red Error Overload LED stays on at load connect the load first and then turn on the startup inverter Otherwise stop using the connected load it s not suitable to drive it with this inverter victron energy 13 Oy PROBLEM Inverter temperature too high Cooling down error keeps on appearing Possible cause Remedy Airflow around the inverter is obstructed Make sure there is at least 10 centimeters of clearance around the inverter Remove any items placed on or over the inverter Keep the inverter away
19. previous one see picture below Apply sufficient torque to the nuts so that the spring washers are fully compressed but avoid bending the main PCB gt M5 nut Flatblade Spring washer screwdriver f plain washer ESS an plain washer DC FUSE J AC Fuseholder DC Fuse sideview with correct order sideview of mounting washers and nuts 4 Place the cover carefully back again without hitting the internal DC fuse and or frontpanel printed circuit board Put all eight screws including the spring washers back in place Now you can reinstall your inverter If the replaced fuse blows again while the inverter is installed correctly the unit must be returned for serive to your local distributor 16 victron energy Oy 6 TECHNICAL SPECIFICATIONS DECLARATION OF CONFORMITY 6 1 Phoenix 12 1000 TECHNICAL DATA Phoenix 12 1000 Cont output at 25 Cont output power at 25 C Cont output power at 40 C Peak power Short circuit output current Output frequency Admissible cos y of Toad Input voltage CO Nominal 12VDC Range static 10 5 16VDC Range 1000VA 9 7 16VDC Maximum input ripple voltage 1 3VACrms Efficiency ANN a Maximum Pnom No load power consumption at nominal input voltage No load power consumption at nominal input voltage in automatic standby mode Automatic standby thresho
20. rt the WARNING inverter 3 SELF DIAGNOSIS SYSTEM TROUBLESHOOTING 3 1 The blink sequence table This Phoenix inverter is equipped with a self diagnosis system to inform you about the cause of inverter shut down To visualize this the red Error Overload LED can blink in four different sequences The duration or timeperiod of this sequence is about 1 second During this timeperiod the red LED can blink four times in a row at most The number of blinks in this time period indicates the cause of inverter shut down victron energy 11 AO 12 In the table below you can find out what kind of blinking sequence belongs to which error Red LED conditions O LED blinking e LEDON O LEDOFF Time period 1 second Type of error 0000 Battery voltage too low or too high one blink per second 0000 Overloaded or shorted output two blinks per second 0000 Inverter temperature too high Cooling down three blinks per second 0000 Too high input ripple voltage four blinks per second e Overload output in current limit IN A BATTERY VOLTAGE TOO LOW OR TOO HIGH ERROR THE INVERTER WILL AUTOMATICALLY RESTART WHEN THE BATTERY VOLTAGE IS IN NORMAL SPECIFIED RANGE AGAIN IN AN OVERLOADED OR SHORTED OUTPUT ERROR THE INVERTER WILL AUTOMATICALLY RESTART AFTER APPROX 18 SECONDS IN AN INVERTER TEMPERATURE TOO HIGH ERROR THE INVERTER WILL AUTOMATICALLY RESTART WHEN THE TEMPERATURE H
21. s from the date of purchase During this period Victron Energy will repair the defective inverter free of charge Victron Energy is not responsible for any costs of the transport of this inverter This warranty is void if the inverter has suffered any physical damage or alteration either internally or externally and does not cover damage arising from improper use attempting to operate the inverter with excessive power consumption requirements or from use in an unsuitable environment This warranty will not apply where the product has been misused neglected improperly installed or repaired by anyone other than Victron Energy Victron Energy is not responsible for any loss damage or costs arising from improper use use in an unsuitable environment improper installing of the inverter and inverter malfunctioning victron energy MO 5 MAINTENANCE FUSE REPLACEMENT 5 1 Maintenance Your Phoenix inverter does not need any specific maintenance besides checking all DC and AC connections at least once a year Check if all nuts and bolts in the electrical system are still tightened sufficiently and if that cables are in good condition Keep the inverter reasonably clean and remove dust fibres gathered at the fan in and outlets to avoid airflow obstruction 5 2 Replacing fuses The inverter is equipped with two internal fuses one on the DC side and one on the AC side These fuses will only blow in case of serious malfunction and or external
22. tus optically by different blinking sequences depending on the error situation See the troubleshooting chapter for the blinking sequence table Also the inverter will warn you acoustically before it s going to shut down due to low battery overload or high temperature condition A bidirectional communication port is available too for future options like a remote panel or connection to a network of power system equipment To get optimum performance and safe operation from your inverter it must be installed and used properly Please read this manual very carefully especially the warning and caution statements before installing and using your Phoenix inverter 2 INSTALLATION 2 1 Location of the inverter pas a ea EME 3 l FAN 1 2 3 4 5 1 Ceiling mounting Only recommended when ceiling is fixed and not removable 2 Floor mounting OK 3 Vertical wall mounting fan at bottom OK beware of small objects falling through the ventilation openings on top 4 Vertical wall mounting fan on top Not recommended reduces inverter capacity due to insufficient cooling 5 Horizontal wall mounting OK For best operating results the inverter should be placed on a flat surface To ensure a trouble free operation of the inverter it must be used in locations that meet the followi
23. victron ene AN y rgy USER MANUAL GEBRUIKSAANWIJZING Phoenix 12 1000 CE Copyrights 1999 2000 Victron Energy B V All Rights Reserved This publication or part thereoff may not reproduced in any form by any method for any purpose VICTRON ENERGY B V MAKES NO WARRANTY EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE REGARDING THESE VICTRON ENERGY PRODUCTS AND MAKES SUCH VICTRON ENERGY PRODUCTS AVAILABLE SOLELY ON AN AS IS BASIS IN NO EVENT SHALL VICTRON ENERGY B V BE LIABLE TO ANYONE FOR SPECIAL COLLATERAL INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING OUT OF PURCHASE OR USE OF THESE VICTRON ENERGY PRODUCTS THE SOLE AND EXCLUSIVE LIABILITY TO VICTRON ENERGY B V REGARDLESS OF THE FORM OF ACTION SHALL NOT EXCEED THE PURCHASE PRICE OF THE VICTRON ENERGY PRODUCTS DESCRIBED HERE IN For conditions of use and permission to use this manual for publication in other than the Dutch or English language contact Victron Energy B V Victron Energy B V reserves the right to revise and improve its products as it sees fit This publication describes the state of this product at the time of its publication and may not reflect the product at all times in the future victron energy MO English description Page 4 Nederlandse beschrijving Pagina 19 victron energy MO SAFETY RULES General Please famil
Download Pdf Manuals
Related Search