DS551LX4_User Manual..
Contents
1. DS551LX4 User Manual 14 Operating Instructions Powering On Off the Display To turn on off the display press the power switch on the back of the display as shown in the diagram below e NOTE The remote control only works when the power switch is ON Using the Remote Control When using the remote control aim the remote at the IR receiver on the display The IR receiver on the DS551LX4 model is at the rear of the display with a receiving angle of 100 degrees The IR receiver configurations of the model are shown in the figure below The operating range of the remote control is 2 5 meters 8 feet Ambient light may affect the performance of the remote control Avoid fluorescent or neon lights in the vicinity DS551LX4 User Manual 15 DS551LX4 Unit mm Front DS551LX4 User Manual 16 Using the Remote Control cont DESCRIPTION Power On Off OSD On Off Move the cursor up or change the setting of selected item Exit the current selection Select the highlighted item Move the cursor down or change the setting of selected item DS551LX4 User Manual 17 Using the Rear Panel Controls ao0o00oa U U L UL Li l 100 OOOOOOOOCGOOOOOCOCSOE JOQOGOWOOQDOOOOOOGOGOO gQooooooooonononogoooaococ 1000006 my a P Pa P a a Pa a P Pa P P aT a Pa P Pa e mS 2000006 D 0 090 0 G 3 0 0 0000 C 0000000060 20 000 Oooo C EREL 0 0 M B el FE LL 1000000900 G D OGO 002. DS551LX4 User Manual 1 Limited Warranty WARRANTY COVERAGE DynaScan s warranty obligations are limited to the terms set forth below DynaScan warrants its product against defects in materials and workmanship for a period of TWO 2 YEARS from the date of initial installation f a defect exists DynaScan will repair the product at no charge A replacement part assumes the remaining warranty of the original product or NINETY 90 DAYS from the date of replacement or repair whichever provides longer coverage for you When a part is exchanged any replacement item becomes your property and the replaced item becomes DynaScan s property OBTAINING WARRANTY SERVICE You must contact DynaScan identify the unit by model number serial number and date of purchase and furnish a brief description of the problem EXCLUSIONS AND LIMITATIONS This Limited Warranty applies only to products manufactured by DynaScan that can be identified by the DynaScan trademark trade name or logo affixed to them The Limited Warranty does not apply to any non DynaScan products or any software even if packaged or sold with DynaScan hardware Non DynaScan manufacturers suppliers or publishers may provide their own warranties DynaScan and its Authorized Service Providers are not liable for any damage to or loss of data or other information stored on any media or any non DynaScan product or part not covered by this warranty This warranty does not apply a to damage ca
3. Professional LCDs User Manual CX XT DynaScan Version 2 00 The use of diagrams and illustrations in the manual are for reference only The actual product may be different Product design and specifications are subject to change without notice Contents Limited Warranty MERE 2 Material Contents Declaration aaa ss nnne nennen nnne ss nan nnns sinas nnns 3 Recycling and Energy Information esse sees eee eee eee 3 BOT eiee eis 4 SAIEIY FIECAUNONS ne o mo m m 5 DATE Proca Uon crm 5 Important Safety Information eee ee eee e 6 amp 2111970 SA EE RRC CE 7 Sod Uc NEL od 7 Installing and Replacing Remote Control Batteries 7 JEZU ZIE mee ES RE sen ee ee ee ORE E ee 8 KIOU ojo OW 8 Connecting tora Power ee Tom a EE aa aa 10 Connecting an External Video Source eee eee eee 10 Connecting Multiple Displays for Video Wall Applications ss 11 SONR CIOFPOSNO S TO TEE EMO 13 BOL OO Tee ee nee 14 ODERAUROJNSKUCNONE Zr mmm 15 Powering On Off the Display 15 Using the Remote Control ans ae 15 Using the Rear Panel Controls 18 Navigating the On Screen Display OSD Menu iii 19 Ree Iena FEE RR NE AE 23 bi BNG o PCO 24 STE Te lT LS RT 25 Digital RGB Output DVI D DV nd 25 Digital RGB Input DVI D DV nn Saai 25 See re o UA EE EEC 26 Ro ZIZ INPUT RE EN 26 OBS GO WAG R CC O CE 27
4. Over Heat Protection Not displayed Information 1 E Adjusted value Each R G B value for this product has been individually adjusted during production to a preset color temperature of 6500K DS551LX4 User Manual 22 Specifications Native Resolution 3000 cd m Typ 1 300 1 Static Contrast Ratio 1 000 000 1 Dynamic Power Supply Hated Voltage 100 240V 50 60Hz MECHANICAL Monitor Dimension SPECS LxHxD w o Stand 1213 4 x 684 2 x 110 5 mm Monitor Weight set package ENVIRONMENT 1096 8096 RH Non Condensing IN 1 OUT 1 support HDMI HDCP IN OUT 1 F2 Design and specifications are subject to change without notice The resolution of DVI D out is 1920 x 1080 1080p only DS551LX4 User Manual 23 Input Mode Active Resolution Refresh Rate Pixel Rate Aspect Ratio HPixels VLines 25 175 MHz 27 MHz gt 59 94 Hz 27 MHz 40 MHz 1024 _ 65 MHz 1280 79 5 MHz 1360 85 5 MHz 1920 1080 om 1485MHz 16 9 DS551LX4 User Manual 24 Pin Assignments Digital RGB Output DVI D DVI O jIXx O9 TXI t7 TXO Shield TX1 TX3 06 DDC Serial Clock 14 5Vpowr 22 Shield TXC 08 DDC Serial Data Hot plug detect Digital RGB Input DVI D DVI 01 RX2 09 RX 17 RKO NC 116 06 08 NC DS551LX4 User Manual 25 RS 232 Output PINNo NAME 0
5. Incorrect usage of batteries may cause leakage or explosion e Pay attention to the polarity when installing the batteries Do not mix different types of batteries or new and used batteries Doing so may shorten the battery life or cause leakage Remove or replace the batteries when they are empty in order to prevent acid leaking in the battery compartment Do not touch the leaked substance from the batteries in case of a battery leakage Doing so may hurt human skin Note If the remote control is not going to be used for a long time we recommend removing the batteries from the remote control DS551LX4 User Manual 7 Installation The LCD must be properly installed using a wall mount Incorrect installation may cause injury or damage the equipment Product warranty does not cover the damage caused by improper installation and DynaScan shall not be held responsible for such incident Mounting o Hanging the Professional LCD from the ceiling or mounting it on the wall is the responsibility of the user Not all ceilings or walls provide enough strength to support the LCD The LCD may drop and cause serious injury if it is hanging from the ceiling with insufficient support or is mounted on a slanted wall Product warranty does not cover improper installation modification or damage caused by natural disasters DynaScan recommends having certified professionals to evaluate the installation site and perform the mounting operation e
6. not cover the vents and or the heat sink o Do not install the LCD beside radiators or other heat sources The installation site should have sufficient ventilation so the heat generated by the LCD can be dissipated e Do not use the Signage in a hot humid dusty or fumy environment e Handle the LCD with care Save the packaging materials for transport later e Clean the LCD backside at least once a month for dust and other particles Unplug the LCD immediately and contact a DynaScan certified service professional as soon as possible when any of the following situations occurs e Damaged power cord or power plug If liquid or foreign object has entered the LCD If the LCD has been exposed to rain or water If the LCD has been dropped or the casing has become damaged If any structural damage such as cracks or unnatural vibration is found If the LCD cannot be operated following the steps outlined in this manual If the LCD emits smoke or other odors or generates strange noises Operating Suggestions e Avoid displaying a stationary image for a long period of time in order to prevent image sticking Cleaning the Panel Use a soft lint free cloth to gently wipe the dust off from the screen panel e Do not use any hard material to wipe the panel Do not poke the panel with your hand or any sharp object such as a pen or a nail or exert excessive pressure on the panel to prevent any damage e Do not use any cleaning solutions o
7. power cable provided plug it in the power inlet on the back of the display shown in the diagram below Connect the power cable to a 110 220 volt 50 60Hz AC power outlet Insert the plug completely into the socket A loose power connection may cause damage to the display and or lead to a fire hazard Connecting an External Video Source Turn OFF the power of both LCD and external video device Using the DVI cable provided insert one end into the DVI IN on the back of the display shown the in the diagram below Connect the other end of the DVI cable to the DVI output of the video source Refer to your video device s manual for additional information DS551LX4 User Manual 10 DVI Cable Connecting Multiple Displays for Video Wall Applications To daisy chain multiple displays for a video wall application connect a video source to the 1 display into the chain with the supplied DVI cable and RS 232 cable Connect the DVI OUT of the 1 display to the DVI IN of the 2 display Using the RS 232 cable provided connect the RS 232 OUT of the 1 display to the RS 232 IN of the Du display Repeat the connection for the remaining displays Use the OSD Menu or Display Manager software to configure the size of the video wall and the position of each display Note The maximum number of DS551LX4 s in a Video Wall is 36 Note The DynaScan Display Manager application is required to be installed on the P
8. use alcohol or other chemical liquids If you smell smoke or hear strange noises immediately unplug the monitor and contact the vendor Do not discard this product with general household waste Be sure to comply with the local waste regulations for disposal ouitable for mounting on concrete and non combustible surface only IMAGE BURN IN WARNING When a stationary or fixed image is displayed on the screen for a long time the image may be permanently imprinted on the screen This phenomenon is known as image burn in and is not covered by the manufacturer s warranty In order to avoid burn in avoid prolonged display of static or fixed images on the screen DS551LX4 User Manual 5 Important Safety Information e Disassembling the LCD is strictly prohibited Opening the cover may expose the user to electric shock or other hazards Please contact DynaScan certified service professionals for all maintenance requirements e Do not allow any liquid to enter the LCD Also avoid placing the LCD close to water sources Do not place heavy objects on the power cord A damaged power cord might cause electric shock or fire Do not bend twist or damage the power cord The power cord must comply with the local safety regulations Do not damage or modify the prongs pins and the ground contact on the power cord plug Do not place the LCD on an unleveled surface or an unstable vehicle The LCD could fall over and cause substantial damage Do
9. 006 95 EC Electromagnetic Compatibility Directive 2004 108 EC IEC 60950 1 2005 2 Edition Am1 2009 EN 60950 1 2006 A11 2009 Am1 2010 A12 2011 EN 55022 2010 AC 2011 Class A ITE EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 EN 55024 2010 EN 61000 4 2 2009 EN 61000 4 3 2006 A1 2008 A2 2010 EN 61000 4 4 2012 EN 61000 4 5 2006 EN 61000 4 6 2009 EN 61000 4 8 2010 DynaScan Technology EN 61000 4 11 2004 Inc VCCI report ready VCCI Class A ITE V 3 2013 04 Technical Requirements V 4 2012 04 Supplementary Test Conditions for Equipment under Test DS551LX4 User Manual 4 Safety Precautions CAUTION Do not install the display in a wet environment or place anything filled with liquid such as a vase or beverage on top of it volatile liquids heating devices Do not install the display in the dusty environment Do not damage the power cord or plug Do not disassemble the screen to avoid electric shock The product can normally be operated at an altitude under 2000m Abnormalities may occur when installing the device at an altitude above 2000m WARNING The heat sink behind the screen may be hot after extensive use Do not touch it to avoid being burned damaging the panel confined space Do not drop or allow any objects to fall on the screen N Do not touch the screen with wet hands to avoid electric shock Unplug the power cord before cleaning the device Use a soft and dry cloth to wipe the screen off Do not
10. 009 ome mgood Oooo Ooo 0 01 A 00 0 0 oct GOT ooo 1000006 0 60 0 0 0 0 61 aan B je O O D z O A O C O e I Z LLI z 2 H Cc O o LU e LU E Move the cursor up or change the setting of selected item DOWN Move the cursor down or change the setting of selected item LEFT Exit the current selection RIGHT Select the highlighted item 18 DS551LX4 User Manual Navigating the On Screen Display OSD Menu Press the MENU button on either the rear panel control or remote control to show the OSD Use the navigation arrows to select and adjust the menu items Color Temperature D65 Time R 100 Video Wall G 100 Backlight B 100 Network Contrast 50 Advance Gamma Native Information 1 Information 2 ITEM 1 ITEM 2 DEFAULT DESCRIPTION ea fim Select the color temperature User D93 eure D65 and D55 Picture a 109 C te gree iit lve ergs 0 100 B too Adjust the blue light level Range0 100 Picture Current Time Power Control Timer Video Wall Power On Time Backlight Power Off Time Network Advance Information 1 Information 2 Set the clock Current Time HH MM Note The internal clock will continue to function when the power is turned off Power Control Off Turn on off automatic power schedule Timer function HH MM Set turn on time Power Off Time HH MM Set turn off time DS551LX4 User Manual 19 Picture Number of Rows Time N
11. 6 Gomnectedto4 2 24 07 08 07 Connected to 1 amp 8 Connected to 1 amp 7 09 TNC RS 232 Input PINNo NAME 06 Connected tp 4 08 Connectedto 1 amp 7 S 0 NO DS551LX4 User Manual 26 Troubleshooting ISSUE TRECOMMENDEDSOLUTON lt e Check whether the DVI in cable is completely plugged in e Check whether the main switch is in the ON position and the power cord is completely plugged in e Check whether the image source s resolution is set to 1920 x 1080 1080p e Check whether the DVI cable is damaged or bent excessively Nothing happens when e Unplug the power cord from the socket and plug it in again after e a few seconds to reset the Signage O Note Unplugging the power cord will not change the settings Image is unstable e Check whether the DVI in cable is completely plugged in Check whether there are batteries in the remote control Check the batteries for freshness polarity etc Check whether the remote is in the operation range Bright light may interfere with the remote control Please avoid using the remote control near special fluorescent lights or neon lights Auto on off does not work or e Check whether the TIMER setting in the menu is set to OFF does not function properly e Check whether the Power On Time and Power Off Time settings are set correctly po 5 e Check whether the RS 232 cable is connected properly If you
12. C in order to use the External Control feature Note The Daisy Chain Setting video wall function only supports a resolution of 1920 x 1080 1080p DS551LX4 User Manual 11 Video Source DVI OUT DISPLAY 1 RS 232 IN i i DVI IN DISPLAY 2 a DISPLAY 3 DS551LX4 User Manual 12 Connector Positions HB B we nf 3000000006 mm 2009000000 100000 nanann M U ias 300000000000000000090C 300000000000000000000 3900000006 x LO D 0000000001 a a a00000C 1000000000 201 0 38 3 4 39 8 105 1 35 3 13 DS551LX4 User Manual Input Output Terminals RJ 45 IN RJ45 network input connection for remote control from PC RS 232 IN RS232C network input connection for remote control from PC DVI IN Connect the DVI D output of a PC or the HDMI output of an AV device via a DVI HDMI cable Audio IN Connect the audio input from an external AV device Extension Connector Extension Connector for optional IR Extension sensor kit ESK201 DVI OUT Output the signal from DVI IN RS 232 OUT RS232 control function for daisy chain application Audio OUT Connect the audio signal output from Audio IN jack to an external AV device Power Switch Press to switch the main power on off AC IN Connect the supplied power cord to the wall outlet AC OUT AC outlet 110 220V up to 100 Watt P gt za SPR ee
13. Do not to cover the vent and or the heat sink in order to ensure proper heat dissipation e Refer to the installation guide provided by the manufacturer for proper mounting When mounting on a wall or hanging from a ceiling e A wall mount is not included in the accessory Please purchase a VESA Standard wall mount to secure the LCD DynaScan is not responsible for the damage caused by using non standard wall mounts e Verify that the mounting location can support the weight of the LCD before installation e The installation angle must be within 15 degrees of the vertical axis Do not install the wall mount while the power is turned on as it may cause serious injury due to electrical shock Greater than 10mm A C 600 400 400 Smaller than 12mm DS551LX4 nor includi 400 400 not including wa mount thickness DS551LX4 User Manual 8 DS551LX4 600 0 Unit mm 306 7 306 7 LSL D UU SOOO oo 39 OOOO Oe 2 00 0 0 0 0 0 QG 000 OC D 0000000000000 amoo a 3D 00 0000 00 0 0 00000009 0 a 9 9 GA D GDA 6 0 9 00 0 EJ EJ 0 0 CI C3 E 0 DEO CI OE CL Ca Ea E a D 0 DDD EL CI OOO oOo ooo oo 2oO00n0005noooooc noonogogaogrc 729 oO 36 60 AE aaa B 15 10 0 0 0 00 00 0 A GO 10 0 0 0 b a c dr Oca 0 0 0 0 DO Goa oo000000nr Orientation When using the LCD in portrait orientation it should be turned clockwise so that the l
14. TAIN THE CONFIDENTIALITY OF DATA STORED ON THE PRODUCT DYNASCAN SPECIFICALLY DOES NOT REPRESENT THAT IT WILL BE ABLE TO REPAIR ANY PRODUCT UNDER THIS WARRANTY OR MAKE A PRODUCT EXCHANGE WITHOUT RISK TO OR LOSS OF PROGRAMS OR DATA DS551LX4 User Manual 2 Material Contents Declaration Hazardous Substances Part Name Lead Mercury Cadmium Hexavalent Polybrominated Polybromodiphenyl Chromium Biphenyls Ethers Pb Hg Cd C PCBA O O O0 O oo Oo cHASSIS O o o o oO o ACCSSORY O O O O O 0 P PACKAGE O O O o o o O indicates that the level of the specified chemical substance is less than the threshold level specified in the standards of SJ T 11363 2006 and EU 2005 618 EC X indicates that the level of the specified chemical substance exceeds the threshold level specified in the standards of SJ T 11363 2006 and EU 2005 618 EC Recycling and Energy Information DynaScan is firmly committed to its environmental protection efforts and we believe that reducing our products impact on the environment is of the utmost importance We are dedicated to meet the latest environmental protection regulations Energy usage Energy Consumption O Mode J Max 500 W Disposal Do not dispose of electrical appliances as unsorted municipal waste use separate collection facilities Contact your local government for information regarding the collection systems a
15. are still having trouble with your DynaScan DS Professional LCD contact your dealer or DynaScan directly for more assistance No image is displayed The remote control does not work DS551LX4 User Manual 27 www dynascanusa com Copyright DynaScan Technology Inc All Rights Reserved
16. eft edge becomes the top edge Installation Location The ceiling or the wall must have enough strength to support the LCD and its accessories Do not install the LCD in a location with strong vibrations or is dusty Do not install the LCD near the building s main electric panel Do not install the LCD at a location where it can be easily removed by the general public When the LCD is installed in an alcove leave at least 10cm 4 of space around it to ensure proper ventilation 9 DS551LX4 User Manual 1 10 cm 4 in A 10cm 4in J ee J When hanging from a ceiling e Ensure that the ceiling is strong enough to support the LCD and it accessories Earthquake unexpected vibration and other external forces should be taken into consideration when evaluating the ceiling strength e The LCD should be secured to the building s structural frame such as a beam rather than light steel frame or interior decoration o Do not use wood screws or dry wall anchors for installation Maintenance e Inspect the fasteners regularly for signs of loosening or deformation Please perform appropriate corrective measures when a problem is identified Neglecting the problem may worsen the situation e Increase the inspection frequency on areas where previous maintenance had occurred to ensure the problems do not occur again Connecting to a Power Source Using the
17. gh Level Time HH MM Set high level time Low Level Time HH MM Set low level time Local Dimmin High Adjusts the contrast High i S contrast Off is the lowest contrast Picture Time Video Wall Backlight Advance Information 1 Information 2 Gateway High is the highest On 192 168 0 100 255 255 255 0 192 168 0 1 ITEM 1 ITEM 2 DEFAULT DESCRIPTION Choose to enable or disable the DHCP function If enabled the display will assign DHCP On the IP address Subnet mask and Default gateway automatically If disabled the following values will be entered manually IP 192 168 0 100 Assign IP address 255 255 255 0 Assign Subnet mask 192 168 0 1 Assign Default gateway Network Display Mode Screen Saver Picture Time Video Wall Backlight Network IR Control Remote Control Power Off Mode Landscape Off RS232 On Standby Reset to Default Setting Off Information 1 Information 2 ITEM 1 ITEM 2 DEFAULT DESCRIPTION Advance Screen Saver The Menu Change the Menu orientation Display Mode Landscape can be displayed in either LANDSCAPE or PORTRAIT mode Turn on off image burn in protection Off op Set image burn in protection interval Choose to use the remote control function Hemote Control RS232 RS230 or Network IR Control Power Off Mode Standby Enable disable the remote control for Menu Note When disabled the remote control function can be enabled agai
18. n from the control panel on the display or through the DynaScan Display Manager application When in Power Off Mode RS 232 controls do not function Only Main Power Switch on the display or Power Button on the remote control can wake up the display DS551LX4 User Manual 21 Restore all settings to default DSR Oi Note It does not modify CURRENT TIME 9 POWER ON TIME and POWER OFF TIME Picture Resolution 1920x1080 60Hz Time Model DS551LX4 Video Wall Serial Number 551LX4XXXXXXXX Backlight Over Heat Protection Mode 0 Network Fan Alarm Advance Information 1 Information 2 Serial Number The display s serial number It will enter into protection mode when the display internal temperature is over heat Mode 0 Brightness 509 Mode 1 Brightness 25 Mode 2 Brightness 03 When the temperature is decreased to exit the protection the brightness will restore to 10096 and Over Heat Protection is disabled When any of the cooling fans on the display rear side is failure and stops running the Fan Alarm Not displayed Fan Alarm will appear and blink and reduce the brightness to 25 Be sure to contact the service engineer for repair Picture Hardware Time Firmware Video Wall Backlight Network Advance Information 1 Information 2 ITEM 1 ITEM 2 DEFAULT DESCRIPTION Information Hardware The HW version Firmware The F W version Some functions may not be available for all models
19. n the panel as it might cause discoloration Cleaning the Casing Unplug the power cord e Gently wipe the casing with a soft cloth Attention o Do not use any of the following solutions to clean the casing as they may damage the paint and cause it to crack or peel benzene solution alkaline solution alcohol based cleaning solution glass cleaner wax polisher or detergent DS551LX4 User Manual 6 Getting Started Contents Confirm that the accessories below are shipped along with the display If any item is missing please contact your dealer The color and shape of the accessories may vary with the products DS551LX4 Professional LCD Remote Control x 1 pc Batteries 1 5V AAA x2 pcs Quick Start Guide x1 pc CD ROM x1 pc Power cable x1 pc RS 232 cable x1 pc DVI cable x1 pc Ethernet crossover cable x1 pc Attention Please use the following table to check whether the included power cord is suitable for your region If the power cord does not match your region please contact your local supplier Please use matching AC socket in order to meet your local safety regulations European Plug Type North America Continental Japan Taiwan Plug Shape EU Region U S A Canada Except U K Japan Voltage 120V 230V 100V 110V Installing and Replacing Remote Control Batteries 1 Open the battery compartment cover 2 Insert 2 new AAA batteries 3 Close the battery compartment cover Warning o
20. umber of Columns Video Wall Row Position Backlight Column Position Network Bezel Compensation Advance Information 1 Information 2 ITEM 1 ITEM 2 DEFAULT DESCRIPTION Set number of rows in a video wall Number of Rows 1 Note The maximum number of rows in a daisy chain is 15 Ne Set number of columns in a video wall 1 Note The maximum number of columns in a Columns de daisy chain is 15 Video Wall Choose to turn the frame compensation function on or off When turned on the display will adjust the image to compensate the width of display bezels in order to accurately display the image Bezel Compensation Picture Auto Brightness Time High Level Video Wall Low Level High Level Time Network Low Level Time Advance Local Dimming Information 1 Information 2 To turn On Off the auto brightness adjustment Note If the AUTO BRIGHTNESS is off the screen brightness will remain at HIGH LEVEL brightness value If the AUTO BRIGHTNESS is on Auto the display brightness adjusts according to the ambient Backlight Auto Brightness light When ambient light is bright the screen will adjust to the HIGH LEVEL brightness value set when ambient light is dark the screen will adjust to the LOW LEVEL brightness value set When the Timer mode is set the display will automatically switch the brightness according to the time set i Adjusts the highest brightness level DS551LX4 User Manual 20 Range 0 100 E Hi
21. used by natural disasters accident abuse misuse misapplication neglect b to damage caused by service including upgrades and expansions performed by anyone who is not an DynaScan Authorized Service Provider c to a product or a part that has been modified without the written permission of DynaScan or d if any DynaScan serial number has been removed or defaced THIS WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED DYNASCAN SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF DYNASCAN CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY ALL SUCH WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY No DynaScan reseller agent or employee is authorized to make any modification extension or addition to this warranty DYNASCAN IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY INCLUDING BUT NOT LIMITED TO LOST PROFITS DOWNTIME GOODWILL DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY ANY COSTS OF RECOVERING OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH DYNASCAN PRODUCTS AND ANY FAILURE TO MAIN
22. vailable If electrical appliances are disposed of in landfills or dumps hazardous substances can leak into the groundwater and get into the food chain damaging your health and well being When replacing old appliances with new one the retailer is legally obligated to take back your old appliances for disposal at least for free of charge DS551LX4 User Manual 3 Declaration of Conformity FCC Verification This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Information This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense We hereby certify that the Professional LCD DS551LX4 is in compliance with Low Voltage Directive 2
Download Pdf Manuals
Related Search