pse-08 user manual
Contents
1. the specification of which the softener can handle B the controller timer does not set properly C pressure in the water supply system is too high or too low D the bypass valve does not set correctly E Short of salt in the tank F controller valve failure A contact local authority for detail of water quality B shorten the re generation cycle time or manually operate the sequence regeneration procedure C add appliance to stabilize the pressure D close the bypass valve E fill up salt F contact distributor 412222. to save the new setting Regeneration time setting Screen display XX XX Default time of the regeneration is 2 A M Press MENU to Return For setting method refer to Press SET to Confirm Regeneration cycle settings Screen display xx days Default regeneration cycle is 7 days Press MENU to Return For setting method refer to 1 Press SET to Confirm Regeneration meter setting Screen display Capacity xx xxm43 Default meter standard is 06 00 m3 Press MENU to Return For setting method refer to Press SET to Confirm Manual Stepwise Regeneration Screen display Backwash Remarks Filter valve only has backwash and rinse settings Brine Draw Rinse Refill The operating procedure is as follows Select the item using key the selected item displays shadowed Press SET to confirm 8 Under backwash status it displays Backwashing Any key to cancel Under this condition press any key to stop backwashing and system returns to the upper menu If this condition stays 30 minutes without pressing any key backwash will stop automatically and system returns to the stand by status Other status operation is as before Under regenerations status including manual stepwise regeneration manual regeneration and system automatic regeneration press any key can stop the process When the system is returning to stand by status no key can be operated during this
3. time and displays Back to Service Please Wait Manual Sequence Regeneration Screen displays Regeneration Any key to cancel M xx Regeneration process is as follows l Backwash System backwash duration according to the settings default setting is 20 minutes enter the next process after finished System Brine Draw System brine draws duration according to the settings default setting is 50 minutes enter the next process after finished l Rinse System rinse duration according to the settings default setting is 15 minutes enter the next process after finished Refill System refills according to the expected time default setting is 10 minutes enter the next process after finished Service System returns to the service when the entire regeneration process completes In the regeneration process press and hold any key for 3 seconds to stop regeneration and system goes back to service status Advanced Settings Backwash Duration l Brine Draw Duration filter valve does not have this option Rinse Duration l Refill Duration filter valve does not have this option Regeneration Mode Load Default Operating procedure is as follows Select the item using key the selected item displays shadowed Press SET to confirm press Menu to back to upper menu Choose the backwash duration it displays xx Minutes Press MENU to Return Press SET t
4. ER SETUP 5 SYSTEM TROUBLESHOOTING 11 FOR USERS The customers are suggested to learn about the quality of raw water before using our system In some circumstances if you apply our system to the raw water which far exceeds the standard water quality for residential some pollutants in the water e g manganese and other heavy metal ions may poison the process agents in the system and cause you have to replace the process agents The process agent in system cannot be out of water soak for long time It will turn dry out and ineffective The process agent cannot work normally under the environment temperature beyond 1 C 38 C Please ensure all the inlets and outlets turn open when the system is at work SYSTEM COMPONENTS Controller The product applies the AMD valve controller for automatic control of the entire system The daily maintenance for the entire system is simple and convenient only need to select the operation on the control panel Water Softener Body The pressure tank in the system uses the FRP and other corrosion resistant materials as the principal together with high quality significant treatment effect of filter media to complete the main task of softening process PLACE TO INSTALL The place where water softener system installed is very important It needs to meet the following conditions Horizontal platform or ground Ambient temperature exceeds 34 F 1 C and below 120 F 49 C water p
5. SEsential INSTRUCTION MANUAL Automatic Water Softener System Model PSE 08 Xsential Water Filtration Systems 78 Daly Street Ascot Western Australia 6104 Ph 1300 366 295 Fax 08 9277 2266 www xsential com au Welcome to use Xsential mini water softener system Thank you for choosing Xsential mini series water softener system We hope that this system can provide you years of service and bring more enjoyment to your home life Before using the new softener system please read the operating instructions carefully Should you be engaged in any problems which cannot be solved by this guide please contact Xsential distributor Functions The specific self maintenance functions of Xsential water softener system can recover the soft water treatment performance for the whole system periodically Therefore it has long term stable softening function without frequent replacement of the filter greatly reducing the operating costs This system can be in parallel or series according to the different requirements to increase water production or further enhance water quality Note To ensure our products can be used for serving your interests at once please make sure all other devices connector valve faucet and so on are firmly connected and in good condition CONTENT FOR USERS 2 SYSTEM COMPONENTS 2 PLACE TO INSTALL 2 SYSTEM INSTALLATION 3 TECHNICAL PARAMETERS 4 LANGUAGE SELECTION 4 GENENRAL OPERATIONS 4 TIM
6. and the display may become hard to recognize but the controller shall be on working When the temperature comes back to normal working temperature the display will return normal Protective cover shall be helpful under high temperature circumstance SYSTEM INSTALLATION THE FOLLOWING OPERATIONS SHALL BE CARRIED OUT BY PROFESSIONAL WORKERS Firstly determine the system installation location Determine the all connection of PSE 08 i e inlet outlet over flow drain and waste water drain Once the connection is known connect the water supply to the inlet connection of the system Connect outlet of PSE 08 to the appliance the supply water pipe diameter cannot be smaller to than inlet pipe on controller to ensure the system provide the normal water production The inlet and outlet pipes shall be installed with mechanical valve The bypass valve is suggested to be installed between the inlet pipe and outlet pipe Connect the waste water drain to the timer Minimize the drain pipe length and corners the distance between controller and drainage channel shall be less than 6 meters An air gap between the drain pipe and the waste water drain is needed to prevent waste water from siphon back into the system Connect the over flow drain to the waste water drain Ensure an air gap is provided between the pipe and the waste water drain DO NOT CONNECT THE WASTE WATER DRAIN AND OVER FLOW DRAIN TO SAME PIPE AT ALL TIME Please do not install any valves
7. ard of controller failure A check power supply to ensure the stable power supply B contact distributor to replace adapter C contact distributor to replace Circuit board Controller valve display system under maintenance A controller internal is clogged B software failure C controller valve failure A disconnect the power adapter and connect again B same as above C contact distributor Water drains cannot stopped be A controller valve restoration failure B Power shut off when the system is under regeneration C controller valve failure A disconnect the power adapter and connect again B switch the bypass valve to bypass or close the controller valve inflow water C contact distributor Water refill cannot stop A refill time setting is too long A Reset refill time ll B Power shut off during water refilling C controller valve failure B switch the bypass valve to bypass or close the controller valve inflow water C contact distributor The output water is salty A Regeneration time setting unreasonable B Timer does not work normally C the brine valve is clogged D the water pressure is too low A increase rinse time and manually operate rinse once B change timer C clean up or replace brine valve D pump up the water pressure The output water after treatment is still hard A The inlet water quality exceeded
8. choose Step 3 press W to choose the English and then press m to confirm When there is no hourglass X displaying on the screen e Simultaneously press m and A to advance one cycle When cam reaches next cycle C2 will be displayed e Repeat m and Ato advance through each cycle C1 C8 It would take about 3 minutes to finish GENERAL OPERATIONS The water quality parameters of each water softener system are predefined the user can choose depending on the specific circumstances 1 Switch on power Turn on the power plug socket switch connecting to the system switch on power and you can hear controller motor starting to work 2 Connect to water supply Firstly open the control valve of outlet pipeline and then open the control valve of inlet pipeline Then the water after softening treatment will supply to you continuously s s 3 Ensure self maintenance function works After a period of work the system will conduct automatic maintenance based on the set time This procedure will consume regenerate The user only needs to set the time and quantity to add recycling regenerate to the system to keep the water quality after treatment within the range of usage as required TIMER SETUP Automatic control system requires a sustained and stable power supply When the power failure happens for any reason in use please reset system timer in order to ensure the system can work in accordance with the initial setup process The co
9. in the drain pipes Each pipe shall have its support point the controller cannot bear the pressure and gravity Ensure the electrical parameter of power supply is consistent with controller s data Insert the power plug into the right socket Warning Do not use lead base solder to weld pipes and do not use tools to tighten the Note plastic connector It may break the connecting point due to the stress All the information described herein is as per commercial standards Local regulation may require user to change the operation procedures as above please check the local administration for accurate information before installation TECHINICAL PARAMETER Integrated Under Cabinet Type Model PSE 08 AMD Electronic Control System Controller Regeneration Period 1 31 Days Default Regeneration Time AM 2 00 Adjustable Municipal Water Inflow Water Quality CaC0O lt 450 mg L 3 gt E Best Softening Flow rate 0 5 tons per hour Best Working Pressure 0 15 0 30MPa Inflow Water Temperature 1 38 C Power Supply 220V AC 50Hz Volume of Regenerant 8 Kg Size of Inlet and Outlet Pipe 1 2 inches Net Weight lt 11 Kg Dimension L W H 360x200x485 mm LANGUAGE SELECTION 1 Language of PSE 08 Step 1 press both Wand A at the same time for about 3 5seconds there will be a new page appear on the screen Step 2 press W for three times to choose the sixth item and then press m to
10. ization status when it turns on During initialization process controller displays System Initializing Please Wait 3 Stand by status Under stand by status the controller displays E Time mode displays Current Day Time XX XX XXXX XX XX XX Time of Next Regen XX XX XXXX XX XX XX m Meter mode display for meter immediate and meter delayed Current Day Time is XX XX XXXX XXIXX XX Residual Total Water XX XXM3 XXXX XXM The accumulated water usage automatically goes back to zero when user restores defaults 4 Parameter Settings Under stand by status press MENU to enter menu setting interface The menu display differently for 3 different regeneration modes more details see menu demonstration Selects the current setting category the display will appears shadowed press SET enters this setting Current Time setting Screen display XX XX XX XX XX Press MENU to Return Press SET to Confirm The current setting appears shadowed then press SET and enter next setting Press MENU to cancel and return to the upper menu Press SET to complete and save the setting It will display Setting Completed Press MENU to Return Now press MENU and returns to the upper menu System will automatically exit and return to the stand by status if there is no operations in one minute And system will automatically resume the previous setting if there is no pressing SET
11. nd hold for 3 seconds to unlock MENU SET four keys control interface key are used to choose or change all settings SET button for setting or confirming and MENU for entering menu or canceling Controller Technical Parameters Maximized Hydrostatic Pressure 20Kg cm m Working Pressure 1 38 7 0Kg cm m Working Temperature 0 C 39 C m Power Adapter Input AC100V AC240V 50Hz 60Hz Output DC12V 178 _ 170 160 160 Controller Functions and Operations 1 Controller Function Selection The system automatically detects Function Set Switcher and Flow Sensor when the system connects to the power supply 1 Picture 1 No 1 and No 2 turns closed the controller is water filter valve Picture 2 No 1 and No 2 turns ON the controller is water softener valve 2 Picture 3 No 3 turns ON the system program language is CHINESE No 3 turns closed the system program language is ENGLISH 3 When there is no flow sensor default set for regeneration is meter delay mode User can set other modes meter immediate mode or time mode 6 When there is flow sensor default set for regeneration is time mode There is no display of other two modes in the menu ON ON ON ree Md oo 123 123 123 Picture 1 Picture 2 Picture 3 2 System initialization The controller will enter the initial
12. ntrol valve is Time type controller when it reaches the setting time the system will automatically start maintenance function The control valve has big LCD display and implements menu styled control mode It is user friendly and the user can modify the parameters displayed on the LCD easily Main Functions of Control Valve Electronic clock Under the stand by status it functions as a clock Automatic regeneration Washing cycle and time can be set Manual regeneration Manual regeneration can be implemented from the menu Manuel mix water function End user can adjust the proportion according to the specific requirement of water quality Automatic meter preference Meter delay mode will be selected automatically when the flow sensor was installed Automatic memorizing Setting information can be memorized when the power is off Reset default All current setting can be cleared and factory defaults can be restored by selecting the reset option Failure protection Motor protection flow sensor failure alarm positioning failure alarm Highlighted characteristics Precisely position controlling implement a precise regeneration process control through infrared detection Large scale LCD display background light All the operation information can be displayed Three regeneration modes time meter immediate meter delayed 5 Child Lock All keys will be locked after 1 minutes during the stand by status press a
13. o Confirm The minutes glittering and shadowed display previous setting time use key to change the setting press SET to save and confirm it will display Setting is Completed Press MENU to Return Press MENU to exit and go back to the upper menu System will automatically exit and return to the stand by status if there is no operations in one minute And system will automatically resume the previous setting if there is no pressing SET to save the new setting Other duration setting is same When it comes to the setting time for regeneration the system will run according to setting time by Advanced Settings and steps by Manual Sequence Regeneration The programmable regeneration time and regeneration cycle start to run the system will generate according to both duration setting and manual regeneration procedure from advanced settings Press any key to stop regeneration and the system goes back to stand by status Regeneration mode J time J meter immediate meter delayed Operating procedure is as follows Select the item using key the selected item displays shadowed Press SET to confirm press Menu to back to upper menu After Choosing meter immediate mode when water consumption reaches the setting amount default value is 06 00tons the system will execute a circle according to manual sequence regeneration setting Press any key for 3 seconds to cancel regeneration the sy
14. ressure below 0 70MPa and above 0 14MPa Stable power supply to the controller The total length of the pipe connected to the water heater should be ten feet three meters at least to prevent backflow of hot water into the system The drainage point should be set as close as possible to the ground Shut off valve or bypass valve needs to be installed in the water pipe connecting points Valve should be designed to meet the minimum deviation of the pipe center the pipe cannot support the weight Before the plastic valve is connected to the pipe make sure all the pipes are welded completely and firmly Outdoor site When the water softener system is installed outdoors following notes must be paid attention Humidity rain may affect equipment performance The system is not designed to undertake the excessive humidity and water spray from below e g continuous severe wet fog corrosive environment nozzle sprays upward 2 Direct sunlight the materials of the product will fade under the direct sunlight but the mechanism won t be reduced If the controller has to be placed under sunlight the protective cover should be placed on the whole unit Temperature the valve and controller will be damaged if the working temperature is too cold or overheated The water in the valve will freeze if the temperature is below freezing then lead to the physical damage of internal components and pipes High temperature will affect the controller
15. stem will return to stand by condition Choosing meter delayed mode after water consumption reaches the setting amount default 10 value is 06 00tons and when it reaches the setting time for regeneration the system will execute a circle according to manual sequence regeneration setting When the circle ended the residual water under stand by status will be initialized automatically restore user s set up of water volume for regeneration cycle default setting is 06 00 tons Press any key for 3 seconds to cancel regeneration system will back to stand by status and returns to the normal service Reset Default The factory default value will be restored if Load Default was chosen Resume the default Press MENU to cancel Press SET to confirm The factory default value is Regeneration time 2 a m Regeneration cycle 7 days Regeneration duration Backwash 20minutes Brine Draw 50mintues Rinse 15minutes Refill 10minutes For meter immediate and meter delayed mode the default meter is 6 00 tons SIMPLE TROUBLESHOOTING Xsential Products are efficient and durable In case of failure during use the following simple troubleshooting list can work as a reference Before repairing the water and pressure inside the system have to be discharged firstly Problems Analysis Solution No display on controller A Power shut off or the power adapter dis connect B Power adapter failure C Circuit bo
Download Pdf Manuals
Related Search