xenarc 708tsu product manual
Contents
1. 708 TSU Installation Manual Table of Contents 2 A eee A 03 Specifications Mer 04 Quick A 05 Hardware Installation _ 07 Software Installation 08 Software Installation Touchscreen Driver Installation lt n 15 3 Features 708 TSU Installation Manual 1 Input Signals USB input 1 channel DC input 1 channel 2 Function Connect computer video signal with a simple USB cable Connect up to six USB Monitors simultaneously 5 Wire Resistive Touch Screen LED backlight with Automatic and manual backlight adjustment High performace Image and Video Signal Processor Monitor is powered by USB port External DC power is not required However the btightness is only running at 70 efficient at USB powered mode When external DC power is connected the brightness will be increase AISS Advanced Image Scaling and Shaping Automatic display driver installation 3 Specification Last input memory USB 2 0 Last power setting memory Auto display adjustment 4 Display Specifications Screen Size Diagonal 7 16 9 Physical Resolution 800 H x 480 V Pixel Pitch 0 0025 H x 0 0075 V in Dot Resolution 2400 x 480 1 152 000 dots Supported Resolution 640 x 480 1920 x 1080 Supported Refresh Rate 60 75Hz LCD Panel Brightness 350 cd m2 Contrast Ratio 400 1 Response Time 5 11ms Viewing Angle Vertical 70 Ho2. Try connect the second USB plug from the USB Y cable as backup power source If external power plug is plugged in this will not be necessary 3 Connect the external DC power plug NOTE 5 Please note that the LCD screen is made with high precision technology However black points or bright points of light red blue or green may appear constantly on the LCD screen and irregular colored stripes or brightness may appear on the LCD screen This is not malfunction Effective dots more than 99 999 Software Installation 14 The length of the mouting screw common between right side and left side Xenarc Technologies Corp TollFree 888 656 6536 E mail support xemarc com website www xenarc com Owner s Records The model and serial numbers are located on the rear of the unit Please record these numbers in the spaces provided below as well as the dealer name address and telephone number Please refer to these records whenever speaking to your dealer regarding this product
3. ecure the stand with screws Monitor Orientation Automatic Landscape orientation image flip while turning the monitor upside down Portrait orientation image flip will need to be setup through disply setting Please refer to DisplayLink maunal for reference Quick Start 6 Please follow the instruction below if you wish to mount the monitor on a VESA wall mount Step1 Attach the VESA plate on the back of the monitor while matching the 4 screw holes on the back side monitor Step2 Installed the 4 screws in place to secure the plate onto the back of monitor The VESA plate comes in 50mm x 50mm and 75mm x 75mm mounting holes 7 Hardware Installation POWER Dimmer adjust the brightness 1 Press and hold the OSD button for more than a second to POWER ON the monitor 2 During operation press the OSD button to change your monitor brightness level 3 Dimmer adjustment level is followed by High Low Medium and Auto Sensor adjustment OSD display for High Dimming level OSD display for Medium Dimming level OSD display for Low Dimming level LOW OSD display for Auto Sensor adjustment Auto 4 Press and Hold the OSD button more than 3 second to POWER OFF the monitor Installing Driver for DisplayLink Graphic Adaptor 708TSU has build in driver for DisplayLink graphic adaptor Your system should auto run the installation wizard when the monitor is plugged in If you are experiencing trouble with t
4. he installation please refer to the DisplayLink Graphics Adapter User Manual that came along with the package Software Installation 8 Installing Touch Screen Driver for 708TSU If Autorun is enabled in your system Installation wizard will launch automatically Select your computer s Operating system The setup wizard will guide user to complete software installation eGalax Touch Ver 5 0 0 Windows 7 Vista XP 2000 Me 98 95 NT4 Windows CE Linux iMac Other Document If setup wizard did not launch you may go to the CD Rom drive and select your Operating System directory manually eGalaxTouch driver software installation package was created with Installshield tool The installation package contains files as below Double click at the setup exe file to start software driver installation Then the setup program will guide user to complete software installation 9 Software Installation Install eGalaxTouch Welcome lo the Install beet dels awd tor tualas Touch oe at Press Next button to continue installation then a new dialog popped up as below Install eGalaxTouch Install eGalaxTouch This dialog shows to ask user if the PS2 filter driver for touch screen to be installed User can check this check for PS2 filter driver installation The standard PS2 mice can still work well after this filter driver installed because eGalaxTouch PS2 filter driver can work with both s
5. ors So that the a multiple monitor setting property page will be shown in eGalaxTouch utility Then press Next to continue 11 Software Installation Install eGalaxTouch A pop up window for user to choose the target path the files will be copied to Then Press Next to continue Install eGalaxTouch Choose Destesstion Loc am me dred A dialog popped up for user to assign the target program folder Press Next Install eGalaxTouch If install RS 232 driver check box was checked the setup program will scan system COM ports The setup program will scan system COM ports to detect if any eGalaxTouch serial device was connected If yes it also pops up a message box for user to make sure if setup program install driver for this new found device Software Installation 12 Install eGalaxTouch Sa LP a 3 a Just Press Yes or No to confirm driver installation for this new found device Install eGalaxTouch mi SISSI PA The eGalaxTouch driver software has been installed We recommend doing the 4 point calibration for alignments to match your display Install eGalaxTouch Finally if PS2 filter driver was installed during this software installation a reboot dialog is popped up for system reboot request to complete driver installation 13 Software Installation ORGE x y Remote Assistance A Windows Messenger MA Macc cum gt Configure Utility A 7 mm Startup gt MES Doc
6. rizontal 70 Colors 18 bit 262 144 colors 5 Physical Specifications Built in USB Sound card Touch Panel O Mini USB connector x1 Self power with USB Connection Single 12V DC_IN for backup power source Supports 9V 18V OSD button for Power and dimmer switch Dimension In 7 17 W x 3 31 H x 5 13 D Weight Ib 1 257 Specification 4 6 Electrical Specifications Operating Voltage Range DC 9V 18V Power Supply DC 12V Power Consumption lt 10W 7 Other Specifications Operating Temperature 4 F 158 F Storage Temperature 22 F 176 F FCC CE ROHS Certification 24 Month Warranty Attach the Mini USB connector at the back of the monitor Attach the USB plug to the computer s USB receptacle connector Plug in the second USB cable is optional It is included as the backup power source OPTIONAL Insert the power adapter as backup power source 5 Quick Start Install the Touch screen driver from the included CD disk and please follow the installation on page 08 Stand installs instruction Step1 Pull out the monitor stand s arm to the correct position Step2 Press and hold the release button located on the top of the stand Attach the monitor with the stand and release the button to secure the monitor in position Step3 Hold the bottom of the monitor stand while adjusting to the comfortable viewing angle Step4 The intended slot is designed to s
7. tandard PS2 mice and PS2 touchscreen But this filter driver may does not work with other devices with the PS2 mouse port After check or uncheck this check box press Next button to continue installation Then it shows new dialog as below Software Installation 10 Install eGalaxTouch This dialog shows to ask user if the RS 232 driver for touch screen to be installed User can check this check for RS 232 driver installation After check or uncheck this check box press Next button to continue installation Then it shows new dialog as below Install eGalaxTouch Tsi y 7 eT Also eGalaxTouch software provides user with a fast 4 points calibration If the system needs 4 points calibration to make sure the touch accuracy every system reboot user can check this check box The 4 points calibration window will be popped up for calibration whenever system boot up if this check box was checked during driver software installation Press Next button to continue installation The setup program prompts a message box to hint Install eGalaxTouch user to make sure that the eGalaxTouch USB controller devices were well connected with system USB ports to guarantee the USB eGalaxTouch device drivers updated after driver installation Then just press OK to continue eGalaxTouch driver package supports multiple monitor operation If your application is for multiple monitors system please check the check box to support multiple monit
8. ument gt Windows Media Player TouchMon 3 Windows Messenger EN Uninstall Il Programs SD Windows Movie Maker After driver installation a shortcut will be generated and shown on the desktop And a new file group generated for eGalaxTouch as below NOTE NOTE 1 Touch Screen device driver must be installed onto your computer in order for the touch Screen to become functional Xenarc Technologies uses Resistive Touch Screen panels in the 708TSU monitor Touch Screen drivers and software for different operating systems can be found in the included CD ROM disc You can refer to this manual for a walkthrough of Touch Screen Driver installation NOTE 2 The maximum voltage supported by the monitor is 18V DC Feeding the monitor with higher voltage will damage the monitor and void the warranty Please use a fused power source if you decide to wire the monitor directly to your car s electrical system It is also crucial that you check the polarity of the connection NOTE 3 If the monitor is not displaying the video signal properly the video signal might be out of range Please try changing your display refresh rate to 60 70 72 or 75Hertz NOTE 4 A single USB port will be enough to power the USB monitor However not all computer s USB port will carry sufficient power If you are experiencing problem with powering on your USB monitor or touch screen please try the following 1 Try connect to different USB Port 2
Download Pdf Manuals
Related Search