fortel_hdfs-55x_signal_processor_manual_rev_a
Contents
1. For Bank Config Rotate Al knob to switch Ch 01 to from Ch 01 up to Ch 03 Rotate A2 knob to switch Ch 02 to from Ch 02 up to Ch 07 Rotate A3 knob to switch Ch 03 to from Ch 03 up to Ch 15 Rotate A4 knob to switch Ch 04 to from Lip Sync Medium 0 000 sec e Tracking e Add Offset Rotate A1 knob to switch Tracking between Slow Medium and Fast Rotate A2 knob to increase or decrease the sec setting Tone Gen Freq e Tone Gen 1 400 Hz e Tone Gen 2 500 Hz e Tone Gen 3 600 Hz e Tone Gen 4 800 Hz Rotate A1 knob to increase or decrease the Tone Gen 1 frequency Rotate A2 knob to increase or decrease the Tone Gen 2 frequency Rotate A3 knob to increase or decrease the Tone Gen 3 frequency Rotate A4 knob to increase or decrease the Tone Gen 4 frequency Tone Gen Level e Tone Gen 1 20 0 dBFS e Tone Gen 2 20 0 dBFS e Tone Gen 3 20 0 dBFS e Tone Gen 4 20 0 dBFS Rotate A1 knob to increase or decrease the Tone Gen dBFS Rotate A2 knob to increase or decrease the Tone Gen 2 dBFS Rotate A3 knob to increase or decrease the Tone Gen 3 dBFS Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards 5 5 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream weg FORTELDTV Main Menu Option Sub Menu Option amp Instructions for Changing Settings Rotate A4 knob to increase or decrease the Tone Gen 4 dBFS Embed Enable2. amp Alarms top left hand side of screen The following is an example of information displayed upon selecting Status amp Alarms For major or minor alarms MajAlm NoVidLock MajLat NoVidLock MinAlm AudInErr MinLat AudInErr For errors DataErr OK ErrSecs 0 For temperature and Over Temperature Threshold 40 0 deg C OvrTempThresh 55 5 deg C 2 Rotate blue knob immediately below the OvrTempThresh setting at the bottom of the screen to increase or decrease that setting See this document s Appendix A SNMP Error Reporting for a list of items related to the HDFS 55X card s Status Alarms capability via Simple Network Management Protocol SNMP information and error reporting Publication 81 9059 0606 0 4 12 Technical Manual uStream em An Input Cfg Input Configuration Choose this option to select the input you want to use Input 1 or Input 2 Step Action 1 From the control panel s main menu screen press the small button next to Input Cfg second button down from top on left hand side of screen 2 Press the small button next to InputSel top button on left hand side of screen to switch between nput 1 and Input 2 3 Rotate blue knob immediately below VidLossAction at the bottom of the screen to select a preferred option when there is a loss of video to the card The following options are offered e Off Freeze Black Timeout
3. Frame Synchronizer card can be mounted in either a FRM 504 high density frame 4RU or a FRM 501 frame 1RU Although a FRM 504 frame can hold up to 18 cards it is recommended that no more than 16 cards be inserted in the frame The FRM 504 frame is especially useful when many cards are needed in a single location using a minimal amount of space For the FRM 501 it is recommended that no more than two cards be inserted in this frame Figure 3 FRM 504 4RU High Density System Frame 1 3 Control Panels FRM 504 and FRM 501 frames require the use of a remote control panel for operating the cards The control panels compatible with these frames are the RCP 502 and RCP 503 Figure 5 RCP 503 Remote Control Panel One of these remote control panels can be used to control cards in other frames by changing a selection on the front panel One control panel can access up to 299 separate Fortel DTV cards The control panel can be placed anywhere in the facility to control cards in multiple frames over a local area network LAN Control panels are connected to frames using LAN hardware e Category 5 patch cables e 100 base T Ethernet switch Although the hardware may be the same type you use for other LAN components in your facility Fortel DTV recommends you isolate their hardware on a separate LAN This is important because other LAN traffic overhead is unpredictable and could task available bandwidth at a time when communications to the syn
4. Publication 81 9059 0606 0 5 6 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream egen Configuring Audio Settings on HDFS 551 and HDFS 552 Cards The following is an example of the RCP 503 s main menu screen for audio configuration Grp 1 lt Phase Grp 2 Mute FS 552 Grp 3 Audio Output Levels Bank Gain Grp 4 Embed Grp 1 Cfg Ch 01 Ch 02 Ch 03 Ch 04 0 0 dB 0 0 dB 0 0 dB 0 0 dB Switching between channel groups Grp 1 Channels 1 4 Grp 2 Channels 5 8 Grp 3 Channels 9 12 Grp 4 Channels 13 16 e Press the small square button next to Grp 1 Grp 2 etc and the corresponding set of channels appears along the bottom of the screen Changing 0 0 dB setting e With Grp 1 selected rotate blue knobs to change 0 0 dB for Ch 01 Ch 02 Ch 03 or Ch 04 e With Grp 2 selected rotate blue knobs to change 0 0 dB for Ch 05 Ch 06 Ch 07 or Ch 08 e With Grp 3 selected rotate blue knobs to change 0 0 dB for Ch 09 Ch 10 Ch 11 or Ch 12 e With Grp 4 selected rotate blue knobs to change 0 0 dB for Ch 13 Ch 14 Ch 15 or Ch 16 Phase e With Grp 1 selected press the small square button next to Phase o The settings under Ch 01 Ch 04 along the bottom of the screen change from 0 0 dB to Normal o Rotate blue knob below any one of the channels and the channel setting switches back and forth between Normal and Invert e To repeat the process for Grp 2 press the small square button ne
5. Remote Control Panel After powering up the RCP 502 control panel and selecting the HDFS 55X card to be configured you are prompted to select either Audio or Video by pressing the appropriate button on the front of the control panel After pressing the Video button the control panel displays the Video Config menu screen From here you can step through a series of screens offering options for configuring the card s Video settings The table below presents an overview of the options you will have an opportunity to set or change Screen s Menu Description Sub Menu Items Status amp Alarms e Temperature Over Temperature Threshold Errors Major or Minor Alarms HDFS Alarm Input e Input Sel Input 1 or Input 2 OnVidLoss Off Freeze Black Timeout o Switch Input Video Format No Timecd Input 1 or Input 2 Primary Output Sec AspRatio HD Config SD Config Genlock Source Frame Rate Test Pattern Encoder Mode HUE O O O O Output Proc Controls Publication 81 9059 0606 0 4 1 C uStream PESA FORTELDTV Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards Screen s Menu Description Sub Menu Items e GAIN e BLACK e CHROMA Color Corrector e Unity Press Preset e White Balance e Black Balance e Gamma Balance e Black e CC Memory Save e CC Memory Recall Vid Processing Min FRM Delay User Reset e Reset User Controls Change Mode Not allowed
6. Switch Input Card Info Choose this option to determine the following about your HDFS 55X card or change its settings e What is the specific Model of your HDFS 55X card e What are the release dates for your card s CPU and FPGA Loads e Change your card s Alias Name e Reser The Card s alias Note Each HDFS 55X card has a default name assigned at the factory You can assign an alias name to a card and that name is stored on the card in non volatile flash memory If a card is moved to a new slot or frame the card retains the selected alias name Step Action Verifying Model and Loads 1 From the control panel s main menu screen press the small button next to Card Info third button down from top on left hand side of screen The following is an example of information pertaining to Model and Loads displayed in the center of the screen upon selecting Card Info CARD INFO Model FS 552 c1 0 1 4 6 2006 11 28 ul v103006_1649 al 2006 08 04 v1 2006 11 01 v2 2006 11 22 v3 2006 12 18 Publication 81 9059 0606 0 HDFS 550 55 1 552 Frame Synchronizer Cards 4 13 C uStream PESA FORTELDTV Step Action Changing Alias Name 2 To change your card s Alias Name press the small button next to Name Card top button right hand side of the screen e The name of the card appears in the middle of the screen in big letters digits Example FS 552 e Two op
7. You will note that the numbers in the next cell Bank 2 to the right of the one you are working in will change to a higher or lower channel number depending on what you set up for Bank 1 e Repeat this process for Bank 2 Bank 3 and Bank 4 AdjacentAudBrd From the Configuration screen press the small square button next to AdjacentAudBrd and the following screen example appears FS 552 Adjacent DAS Audio Board DeEmbed to DAS Embed DAS Audio Grp1 None e Rotate blue knob immediately below DeEmbed to DAS to switch the setting between None Grp1 Grp2 Grp3 and Grp4 e Rotate blue knob immediately below Embed DAS Audio to switch the setting between None Grp1 Grp2 Grp3 and Grp4 e Note A message may appear in the middle of the screen indicating that the Embedded DAS Audio will override local Audio Publication 81 9059 0606 0 5 13 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream PESA FORTELDTV Chapter 6 Troubleshooting 6 1 Network Communication Errors This chapter was developed to assist you in identifying a control communications problem when using remote control panels with Integrity system frames Integrity is designed to transmit and receive data between remote control panels RCPs and cards via the Ethernet on a Local Area Network LAN There are several potential causes of problems identified here with ways to isolate them and render a solution Inte
8. card s Freeze feature Step Action 1 From the control panel s main menu screen press the small button next to Freeze fourth button down on the right hand side of the screen 2 If the screen display shows that the option is turned On and you wish to turn it Off press the button next to Freeze again Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream PESA FORTELDTV Chapter 5 Configuring a Card s Audio Settings 5 1 Introduction This chapter presents step by step instructions for configuring an HDFS 55X card s Audio settings using Fortel DTV s RCP 502 and RCP 503 remote control panels 5 2 RCP 502 Compact Remote Control Panel Audio Figure 11 RCP 502 Compact Remote Control Panel After powering up the RCP 502 control panel and selecting the HDFS 55X card to be configured you are prompted to select either Audio or Video by pressing the appropriate button on the front of the control panel After pressing the Audio button the control panel displays the Audio Config menu screen From here you can step through a series of screens offering options for configuring the card s Audio settings The two tables below present easy to use formats for configuring an HDFS 55X card s audio options using a RCP 502 Remote Control Panel The first table is for the HDFS 550 card and the second tab
9. cccccescsseceseceseceseceeceeeeseeeeeceeeseeeseeeseecseecsaecaeceaeeeseenaeens 2 2 Figure 8 HDFS 55X Input and Output Comnmectors 3 2 Figure 9 RCP 502 Compact Remote Control Panel 4 1 Figure 10 RCP 503 Express Remote Control Panel 4 11 Figure 11 RCP 502 Compact Remote Control Panel 5 1 Figure 12 RCP 503 Express Remote Control Panel 5 6 Figure 13 Integrity System Flow Diagram cccccccssecsseceseceeceseeeeeseeeseeeseeeeseeeeseesseecseecauecaeceaeeeeeenaeens 6 1 Figure 14 Jumpers on a Typical HDFS 55X Card B 1 Figure 15 User Selected Jumper Senge B 1 Publication 81 9059 0606 0 Rev A Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream egenen Important Safeguards and Regulatory Notices Information on the following pages provides important safety guidelines for both Operator and Service Personnel Specific warnings and cautions will be found throughout the manual where they apply but may not appear here Please read and follow the important safety information noting especially those instructions related to risk of fire electrical shock or injury to persons Danger e Electrical potential is still applied to some internal components even when power switch breaker is in the off position To prevent electrical shock when working on this equipment disconnect the AC line cord source before working on any internal components e Residual voltage may be present immediately after unplugging the system due
10. for ventilation Do not block them The front door is part of the fire enclosure and should be kept closed during normal operation e To prevent damage to this equipment read the instructions in this manual for proper input voltage range e Circuit boards in this equipment are populated with surface mount and FPGA components Special tools and techniques are required to safely and effectively troubleshoot and repair modules that use SMT or FPGA components For this reason service and repair of Fortel DTV products incorporating surface mount technology are supported only on a module exchange basis Customers should not attempt to troubleshoot or repair modules that contain SMT components Fortel DTV assumes no liability for damage caused by unauthorized repairs This applies to both in warranty and out of warranty products Power Cord Notices North American Power Supply Cords This equipment is supplied with a molded grounding plug NEMA 5 15P at one end and a molded grounding receptacle IEC 320 C13 at the other end Conductors are color coded white neutral black line and green or green yellow ground International Power Supply Cords This equipment is supplied with a molded grounding receptacle IEC 320 C13 at one end and a molded grounding plug EU1 16P at the other end Conductors are CEE color coded light blue neutral brown line and green yellow ground Other IEC 320 C13 type power supply cords can be used if they comp
11. referred to as the A1 knob 2 Each time you rotate A1 knob one of the following screens appears Use the A2 A3 and A4 knobs to change the settings on each screen Color Corrector White Balance RED 1 000 GRN 1 000 BLU 1 000 Color Corrector Black Balance RED 1 000 GRN 1 000 BLU 1 000 Color Corrector Gamma Balance RED 1 00 GRN 1 00 BLU 1 00 Color Corrector Black Blk Stretch 1 00 Blk Lvl 0 0 IRE Color Corrector CC Memory Save Mem Bank knob F1 1 TAKE to save to Mem Color Corrector CC Memory Recall Mem Bank knob F1 1 TAKE to recall from Mem Note The word TAKE on a screen refers to the Take Enter button 3 Press Take Enter to save your settings Publication 81 9059 0606 0 4 8 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream weg JC FORTELDTV Vid Processing Choose this option to set or change your HDFS 55X card s Frame Delay setting Step Action 1 Min Frame Delay 0 Rotate the A1 knob to change this setting to 0 1 or 2 frames of delay User Reset Choose this option to reset your HDFS 55X card s current settings to the factory default settings Step Action l With the control panel s main menu screen listing the Video Config options rotate A1 knob until User Reset is highlighted on the screen and press Menu The following is an example of information displayed upon selecting User Re
12. screen are used for selecting an option to be checked or changed Figure 10 RCP 503 Express Remote Control Panel Screen s Main Menu Sub Menu Items Status amp Alarms e Minor or Major Alarms e Errors e Temperature and Over Temperature Threshold Input Cfg Input 1 or Input 2 Card Info e Model e CPU and FPGA Loads e Alias Name e Mode Reset Procs Reset Video Processing Amplifier VidProcess e Color Corrector e Full YUV Gamut e Noise Reduce e Legalizers e Detail Enhance e De Interlace Mode Output Cfg e Test Patterns e Pri Out Config e Sec Out Config e Genlock Source e Frame Rate e Format e Encoder Mode Card Reset Reset to Factory Defaults Freeze e Turn ON Option e Turn OFF Option For more detailed information on the RCP 502 and RCP 503 Control Panels see Fortel Publication 81 9059 0606 0 DTV s RCP 502 Compact Remote Control Panel User Manual January 2005 and RCP 503 Remote Control Panel User Manual Revision No 1 01 June 2004 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream weg FORTELDTV Status amp Alarms Choose this option to determine the following about your HDFS 55X card e Does the card have any active Major or Minor Alarms e Isthe card getting any Errors e What is the card s Temperature and its Over Temperature Threshold Step Action 1 From the control panel s main menu screen press the small button next to Status
13. the steps below to 1 Reset All Audio Gains to 0 0 dB and 2 set up Bank Config for four Banks of audio Reset All Audio Gains e Press the small square button next to Reset All Audio Gains to reset the current dB settings back to 0 0 dB Bank Config To set up channels into the four banks press the small square button next to Bank Config see screen above The following screen example appears FS 552 Bank Config These groupings are used for Bank Gain and ALC Ch 01 to Ch 05 to Ch 09 to Ch 13 to Ch 04 Ch 08 Ch 12 Ch 16 e Rotate blue knob immediately below Ch 0 to Ch 04 Bank 1 to change the Ch 04 setting to a higher or lower channel number Publication 81 9059 0606 0 5 8 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream ZS FORTELDTV e You will note that the numbers in the next cell Bank 2 to the right of the one you are working in will change to a higher or lower channel number depending on what you set up for Bank 1 e Repeat this process for Bank 2 Bank 3 and Bank 4 Cfg Configuration From the main menu screen press the small square button next to Cfg lower right hand side of screen The following is an example of the screen that appears Input Status Select Sources FS 552 Tone Gen Audio Configuration Lip Sync ALC Embed Enab ON AdjacentAudBrd Input Status From the Configuration screen press the small square button next
14. to Input Status and the following screen example appears providing Audio Jn information for specific groups Audio In Status DEmbd Grp1 No Input No Input No Input No Input DEmbd Grp2 No Input No Input No Input No Input DEmbd Grp3 No Input No Input No Input No Input DEmbd Grp 4 No Input No Input No Input No Input AES in No Input No Input Tone Gen From the Configuration screen press the small square button next to Tone Gen and the following screen example appears Freq FS 552 Level Audio Tone Generators Set Frequencies TG 1 TG 2 TG 3 TG 4 400 Hz 500 Hz 600 Hz 800 Hz The screen default shows the Freq frequency for each Tone Generator TG e Rotate blue knob immediately below TG 1 TG 2 TG 3 or TG 4 to increase or decrease the frequency for that specific Tone Generator Publication 81 9059 0606 0 5 9 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream weg FORTELDTV Press the small square button next to Level and where there were frequency settings before there are now dBFS settings under TG 1 TG 2 TG 3 and TG 4 See screen example below Freq FS 552 Level Audio Tone Generators Set Frequencies TG 1 TG 2 TG 3 TG 4 20 0 dBFS 20 0 dBFS 20 0 dBFS 20 0 dBFS e Rotate blue knob immediately below TG 1 TG 2 TG 3 or TG 4 to increase or decrease the dBFS settings for that specific Ton
15. to slow discharge of large power supply capacitors Wait 30 seconds to allow capacitors to discharge before working on the system Warnings e Any instructions in this manual that require opening the equipment cover or enclosure are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so Heed all warnings in the unit and in the operating instructions Do not use this equipment in or near water Disconnect AC power before installing any options unless explicitly told to do so in this manual This equipment is grounded through the grounding conductor of the power cord To avoid electric shock connect the power cord to the equipment and plug it into a properly grounded receptacle before connecting the equipment inputs and outputs Receptacle grounding conductor must be connected to earth ground at the service equipment e Dangerous voltages exist at several points within this equipment To avoid personal injury refer all servicing to qualified personnel e During installation do not use the door handles or front panels to lift the equipment as they may open abruptly and injure you e To avoid fire hazard use only components on the specified type voltage and current rating as referenced in the appropriate parts list Always refer fuse replacement to qualified service personnel e To avoid explo
16. to the other end of the same crossover cable 3 Apply power to both the frame and RCP 4 Observe the two LED indicators on the front of the frame marked Remote 1 e The first LED should flicker rapidly indicating traffic over the remote port e The second LED should illuminate steady indicating a correctly connected cable No frames or cards found When an RCP cannot find a frame via a crossover cable it means one of several things may have happened Complete the following steps to troubleshoot the problem Step Action 1 Make sure the controller card ZFCB in the frame is seated in its card socket properly or completely e Ifthe card is not seated properly it will result in a frame s inability to receive communications e Ifthe Remote 1 status LEDs are both extinguished this is possibly the cause of the communication failure Remove the pop off front cover turn the power supplies off then remove the inner center cover to access the ZFCB card Using the card ejectors gently re seat the card in its socket and lock the card ejectors to secure the card Replace the inner cover required for proper ventilation and RF shielding turn the power supplies on then replace the pop off front cover The Remote 1 LEDs on the front cover should now illuminate If not call the factory for further assistance 2 Change the cable There is always a chance you have a defective crossover cable Try a seco
17. 1 552 Frame Synchronizer Cards Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream weg FORTELDIV Appendix B Installing Jumpers on HDFS 55X Cards In nearly all cases jumpers will have been installed on your HDFS 55X card at the factory before the card was delivered and ready for installation However in the event that procedure needs to be corrected or repeated onsite this appendix provides information for installing the jumpers Figure 14 Jumpers on a Typical HDFS 55X Card Input 4 Typical HDFS 55X Card Figure 15 User Selected Jumper Settings Publication 81 9059 0606 0 B 1
18. C uStream e Sieg DTV TECHNICAL MANUAL HDFS 550 551 552 High Definition Frame Synchronizers Lan Publication 81 9059 0606 0 Rev A April 2007 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream PESA FORTELDTV Customer Support Fortel DTV hopes this manual provides answers for nearly all your questions but if it does not please call us in Atlanta Georgia USA Voice 1 770 806 0234 Fax 1 770 806 0244 Fortel DTV Inc 3305 Breckinridge Blvd Suite 118 Duluth GA 30096 4932 USA http www forteldtv com Copyright 2007 Fortel DTV Inc All rights reserved Printed in U S A Fortel DTV products are covered by U S and foreign patents issued and pending Information in this publication supersedes that in all previously published materials Specification and price change privileges reserved Fortel DTV Inc Fortel DTV and the Fortel DTV logo are registered trademarks Integrity DTM Dynamic Threshold Modification and Dual Band Processing are trademarks of Fortel DTV Inc The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Fortel DTV Fortel DTV assumes no responsibility or liability for any errors omissions or inaccuracies that may appear in this publication Publication 81 9059 0606 0 Rev A Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream Ae FORT
19. ELDTV Contents Chapter 1 ANI OAUCHON EG La 1 1 HDFES 55X Cards E 1 1 12 d IT 1 4 13 Control Fagott eege eege 1 4 Chapter 2 Installing Cards in Frame cccscccssccccssscssssssssccsscsscssscsscssscssscsssees 271 2 1 Installing cards in the FRM 504 Integrity System Frame cescecceceseeneeesseeeeeeseeeeeeseees 2 1 2 2 Installing cards in the FRM 501 Integrity System Frame cccesseccceseereeesseeseeeseeeeesseees 2 2 Chapter 3 Connecting a Card to External Systems ccccccscrsccsssssssccsscsssees I L 31 Introducti E 3 1 3 2 HDFS 55X Card s Inputs Outputs sssssennnesnnnnnnunnnennnnnnnnnnnnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nenne 3 1 3 3 Input and Output COMMCCCOMS cssscrcccnccniscacsnsanscaccetaracnsnesnanntenisednadnannnanenizenanancanonaccnteradancananns 3 2 3 4 Input and Qutput Fonge eege eessen eessen eege eege 3 3 Input Formats Supported by HDFS 55X Cards 3 3 Output Formats Supported by HDF S 55X Cards 3 3 Chapter 4 Configuring a Card s Video Settings sscccsssccssecscssesssccsscsccescees 4 1 41 ut e LL EE 4 1 4 2 RCP 502 Compact Remote Control Panel Video ssecceeeeceesseeeseeeeeeeeeseseeesseeeeseeeeessees 4 1 TEE Eeer Eet dee 4 3 Input Input Configuration cccccccccccecceseecceseesceseeseesecseesecseceeneceeesccecsceaeeaeeseseeeeceeseseeaeesesaeeateesneeerenaeeney 4 4 Output Output Configuration ccceccccccccccceecceceseeccsecseeeeeesecseeseceseescnseeseeseceseeceeesc
20. Horizontal and Vertical Phase and positions of the HD output FreezeMode Change from Field 1 to Field 2 or Frame Freeze Turn On or Off HD CloCap Turn closed captioning on or off HD Timecode Turn on or off Sec Out Config Publication 81 9059 0606 0 Press Sec Out Config to access the following settings Timing Adjust Horizontal and Vertical Phase and positions of the SD output SD CloCap Turn closed captioning On or Off SD Timecode Turn on or off Aspect Ratio Note Rotate knob under Aspect Ratio to switch between the following 16X9 Lbox 4X3 Squeeze 4X3 Crop 4 16 C uStream FORTELDTV Step Action Genlock Source Turn the knob below this to change from board connector to frame connector Frame Rate Turn knob below to change from 59 9Hz to 50Hz Encoder Mode Turn knob below to turn encoder on or off or test bars on Card Reset Reset to Factory Defaults Choose this option to reset your HDFS 55X card s current settings to the factory default settings Step Action 1 From the control panel s main menu screen press the small button next to Card Reset third button down on the right hand side of the screen 2 To reset the card to the factory settings press the button next to Reset Note This procedure does not affect timing or calibration settings Freeze Choose this option to turn On or Off the HDFS 55X
21. Lim Grouped Channels e Bank Level o BANK 1 0 0 dB o BANK 2 0 0 dB o BANK 3 0 0 dB o BANK 4 0 0 dB e ALC o Bank Select 1 o ALC Enable Off o ALC Level 0 0 dBFS o ALC Rate 0 e Limiter o Bank Select 1 o Lim Enable Off o Lim Level 0 0 dBFS o Lim Rate 0 e Bank Config o Ch 01 to Ch 02 o Ch 03 to Ch 04 o Ch 05 to Ch 08 o Ch 09 to Grp4 4 Rotate A1 knob to advance through the four first level selections above 1 Bank Level 2 ALC 3 Limiter and 4 Bank Config After making a selection press Menu to get additional selections Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards 5 4 C uStream PESA FORTELDTV Main Menu Option Sub Menu Option amp Instructions for Changing Settings specific to those channels see above For Bank Level Rotate A1 knob to change the 0 0 dB settings for BANK 1 A2 knob for BANK 2 A3 knob for BANK 3 and A4 knob for BANK 4 For ALC Rotate A1 knob to change Bank Select to select 1 of 4 banks Rotate A2 knob to switch between Off and On for ALC Enable Rotate A3 knob to change set the ALC Level 0 0 dBFS setting Rotate A4 knob to change the ALC Rate from between 0 6 For Limiter Rotate A1 knob to change Bank Select to select 1 of 4 banks Rotate A2 knob to switch between Off and On for Lim Enable Rotate A3 knob to change set the Lim Level 0 0 dBFS setting Rotate A4 knob to change the Lim Rate from between 0 15
22. NTSC e 16 Channels of Internal Audio and e PAL Synchronization ALC e Genlock HDFS 552 High Definition Frame e 2HD SDI Inputs or 1 HD SDI 1 AES Synchronizer Card with outputs Input e SDI e 2 HD Outputs e NTSC e 2 SDI Outputs 2 Selectable e PAL SD AES NTSC Outputs e AES e 16 Channels of Internal Audio and Synchronization ALC e Genlock 3 1 C uStream Pusat FORTELDTV 3 3 Input and Output Connectors KAAKAA Figure 8 HDFS 55X Input and Output Connectors The following table presents specifics on the Input Output connections for HDFS 55X cards Input Output Description BNC Connector Input 1 Primary Serial Digital Video Input 1 5Gb s HD input per SMPTE 292M or 270Mb s SDI input per SMPTE 259M Input 2 Secondary Input used as e User selectable alternate to primary video input e Automatic backup video input used in case of failure on main input e AES audio input Output 1A Primary Video Output SD or HD depending on input Output 1B Duplicate of Output 1A Output 2A Secondary Video Output SD version of primary Output 2B Duplicate of Output 2A Option A Optional Output jumper selectable as e Duplicate of Output 2A e Composite video output based on a decimation of the primary output e One AES pair selectable from any embedded audio group Option B Optional Output jumper selectable independently from Option A as e Duplicate of Output 2A e Composite video
23. TSC PAL output timed to reference jumper to AES Synchronizer and Legalizer standard Optional color corrector with eight memory settings Four group de embed synchronization and all audio processing including shuffle phase reversal summing soft clip ALC Dolby E synchronization and embed e Works with DAS 441 for parallel audio synchronization analog or AES with or without de embed and embed Publication 81 9059 0606 0 1 1 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream PESA orton HDFS 550 551 552 Cards Individual Features Synchronizer Legalizer v Color Corrector optional vi Embedded Audio v v vi AES I O DAS 441 v Analog Video Out NE CE NE NECENT gt Pri men Ref yj gt Pri HDYSD HD SD 1 C Ser SD Sec SD CH SD Anig AES 1 2 SD AnIg AES 2 Figure 1 HDFS 550 551 552 High Definition Frame Synchronizer Cards Publication 81 9059 0606 0 1 2 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream a mor 3324 nner 992323 i U t 3 f D i L E Guer i Jumpers Figure 2 HDFS 552 High Definition Frame Synchronizer Card Note See Appendix B for information on installing jumpers on an HDFS 55X card Publication 81 9059 0606 0 1 3 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream reset FORTELDTV 1 2 Frame An HDFS 550 551 552 High Definition
24. ble below Primary Output Freeze Mode Field 1 Note Rotate A2 knob to change setting between Field 1 Field 2 or Frame Sec AspRatio 16X9 Lbox Rotate Al knob to change setting HD Config Outputs 1A amp 1B HD Config e HD CloCap HD Timecode e HD Legalizer HD Timing HD H Phase HD V Phase HD H Video Pos HD V Video Pos Note For each of these above options press Menu to view additional options and make selections SD Config Publication 81 9059 0606 0 SD Config e SD CloCap e SD Timecode e SD Legalizer SD Timing H Phase V Phase H Pos V Pos Note For each of these above options press Menu to view 4 5 C uStream PESA Technical Manual HDFS 550 551 552 Frame Synchronizer Cards FORTELDTV Step Action additional options and make selections Genlock Source e Frame Connector e Board Connector Note Rotate Al knob to switch between these two options Frame Rate 59 9 Hz Note Rotate Al knob to switch between 50 Hz and 59 9 Hz Test Pattern e 75 Bars e Multiburst e Sweep e NTC7 Composite e Luma Ramp e YC Ramp e YUV Ramp e Blanking Note Rotate Al knob to switch between these options Encoder Mode e On e Test Bars e Off Note Rotate A1 knob to switch between these options 4 After setting or changing any settings press Take Enter to save your selections Publication 81 9059 0606 0 4 6 C
25. chronizers is critical For more detailed information on the RCP 502 and RCP 503 Control Panels see Fortel g DTV s RCP 502 Compact Remote Control Panel User Manual January 2005 and RCP 503 Remote Control Panel User Manual Revision No 1 01 June 2004 Publication 81 9059 0606 0 1 4 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream egenen Chapter 2 Installing Cards in a Frame 2 1 Installing cards in the FRM 504 Integrity System Frame The FRM 504 Integrity System Frame can hold a maximum of 18 cards but it is recommended that no more than 16 cards be inserted in the frame 1 Carefully load cards through the rear of the frame e Card slot number is nearest to the power supply side e Card slot number 18 is farthest from the power supplies 2 Card guides at the top and bottom of each slot are used to align the card with the mating connector on the mid plane card as the card is inserted fully into the frame 3 After cards are gently seated into the mating connector secure them to the top and bottom rail of the frame using the two captive screws attached to each card Figure 6 FRM 504 Integrity System Frame Publication 81 9059 0606 0 2 1 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream PESA FORTELDTV 2 2 Installing cards in the FRM 501 Integrity System Frame The FRM 501 Integrity System Frame can hold a maximum of four cards but it is recommended that no m
26. d On e Rotate blue knob immediately below the ALC Level setting to increase or decrease its dBFS setting e Rotate blue knob immediately below the ALC Rate setting to switch its setting between 0 6 e Rotate blue know immediately below the Peak Limiter Level setting to increase or decrease its dBFS setting Increasing or decreasing this setting may change the setting under ALC Level This is normal e Rotate blue knob immediately below the Peak Limiter Rate setting to switch its setting between 0 15 Publication 81 9059 0606 0 5 12 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream Pasay FORTELDTV Bank Config Bank Config allows you to divide up the system s 16 audio channels into four banks Bank 1 Bank 2 Bank 3 and Bank 4 This feature allows you to quickly set audio levels for multiple channels simultaneously For example because of a particular hardware setup you may want to have Channels 1 6 set up in Bank 1 Channels 7 and 8 set up in Bank 2 Channels 9 11 in Bank 3 and Channels 12 16 in Bank 4 From the ALC Config screen press the small square button next to Bank Config and the following screen example appears FS 552 Bank Config These groupings are used for Bank Gain and ALC Ch 01 to Ch 05 to Ch 09 to Ch 13 to Ch 04 Ch 08 Ch 12 Ch 16 e Rotate blue knob immediately below Ch 0 to Ch 04 Bank 1 to change the Ch 04 setting to a higher or lower channel number
27. e Generator Lip Sync From the Configuration screen press the small square button next to Lip Sync and the following screen example appears FS 552 Audio Lip Sync Adjust Tracking Add Offset Slow 0 000 sec e Rotate blue knob immediately below Tracking to switch its setting between Slow Medium and Fast e Rotate blue knob immediately below Add Offset to change the number of seconds offset for Lip Sync Embed Enab From the Configuration screen press the small square button repeatedly next to Embed Enab to switch settings between On and Off Publication 81 9059 0606 0 5 10 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream Pusat FORTELDTV Select Sources From the Configuration screen press the small square button next to Select Sources and the following screen example appears AES Out Sources FS 552 For each output chan select a source Output Ch is SRC SumWith SumBalance Ch 01 AES1 1 None 0 0 dB e Rotate blue knob immediately below Output Ch to select a channel number The information displayed immediately to the right and under is SRC SumWith and SumBalance changes simultaneously to display their settings for the channel you have selected Those settings do not change if there is no change for the channel you have selected If you wish to change the settings for is SRC SumWith and SumBalance for your selected channel r
28. e On e Off Rotate A1 knob to switch between On and Off 5 3 RCP 503 Remote Control Panel Audio Sa CETE aun RS SSS Le a ms BERR un Figure 12 RCP 503 Express Remote Control Panel After powering up the RCP 503 control panel and selecting the HDFS 55X card to be configured press the Audio button and the control panel displays the Audio Config menu screen From here you can step through a series of screens offering options for configuring the card s Audio settings The two tables below present easy to use formats for configuring an HDFS 55X card s audio options using a RCP 503 Remote Control Panel The first table is for the HDFS 550 card and the second table is for the HDFS 551 and HDFS 552 cards The tables provide instructions on what knobs to use to set each option Configuring Audio Settings on HDFS 550 Card From the Configuration screen press the small square button next to AdjacentAudBrd and the following screen example appears FS 550 Adjacent DAS Audio Board DeEmbed to DAS Embed DAS Audio Grp1 None e Rotate blue knob immediately below DeEmbed to DAS to switch the setting between None Grp1 Grp2 Grp3 and Grp4 e Rotate blue knob immediately below Embed DAS Audio to switch the setting between None Grp1 Grp2 Grp3 and Grp4 Note A message may appear in the middle of the screen indicating that the Embedded DAS Audio will override local Audio
29. eesesteseneseeesnseeesneeereegs 4 5 PROG EE 4 7 Color EE 4 8 e 4 9 User Reset sisson ra A E geed Eed 4 9 Change Mode isrener a a EE 4 9 C rd eebe 4 10 4 3 RCP 503 Remote Control Panel Video sssuussssenunsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnne 4 11 St tus COALAIING siiras S E E E A E E EE ETS EEO EEN E ESE EOE OPiS 4 12 Input Cfg Input Confieuration 4 13 G rd INO ssa a ni e T E E E cats a Ee EELER 4 13 Res t Procs Reset th Proc AMp enesesse osne e aaaea aa aE a eanna r an 4 14 Vid Process Vid o Processing icis iinet iiie sdgqeseabandas coidptebendanedeauasbesteses 4 15 Output Cfg Output Configuration sonas iiniioieniiiieenieiidoisiaieii 4 16 Card Reset Reset to Factory Deiere 4 17 HEP CO LO ts EVENE VE ee Eege O N E E A E A ET 4 17 Chapter 3 Configuring a Card s Audio Settings sccssssccssssssssssssecsssssecsseees J L S1 Introduci n arrana AA AEEA AREN AAAA AAAA ARAA 5 1 5 2 RCP 502 Compact Remote Control Panel AUCIO cssseecccessseeeeeeseeeeeeeseneeeeenesneneneeseenes 5 1 Configuring Audio Settings on HDFS 550 Cord 5 1 Configuring Audio Settings on HDFS 551 and HDFS 552 Code 5 2 5 3 RCP 503 Remote Control Panel Audio ccccseeeeceseseeeeeseeeeeeeaeeneeenseeneeeeaseeneeseseeeeensesnenes 5 6 Configuring Audio Settings on HDF S 550 Cord 5 6 Configuring Audio Settings on HDF S 551 and HDFS 552 Code 5 7 Phase E 5 7 Mule arere Neare EEE ee eege eege 5 7 Eeer eege 5 8 GS CO
30. grity Frame Ethernet Hub or Control Panel and Cards Switch RCP 30x Additional Frames and Control Panels Figure 13 Integrity System Flow Diagram 6 2 Recommended Network Configuration The recommended configuration for Integrity is to use an off the shelf Ethernet switch to connect all frames and RCPs For large systems multiple switches may be cascaded All devices are connected using Ethernet patch cables such as those used to connect a PC to a switch or patch panel Each RCP must be assigned a unique IP and MAC address Assignments may be changed via a menu in the RCP There is a specific range of addresses that are considered valid Invalid values will cause a system communication failure Publication 81 9059 0606 0 6 1 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream Poea FORTELDTV 6 3 When Things Do Not Work Isolating the fault is the key step in locating a network communications problem Integrity RCPs are designed to communicate over a network using patch cables or directly connected to an Integrity system frame using an Ethernet crossover cable not a patch cable This allows you to determine if the fault is either the frame or a particular control panel To troubleshoot a problem complete the following steps Step Action 1 Connect one RCP via the Remote 1 port on the back panel to one end of the crossover cable 2 Connect the frame via the Remote 1 port on the back panel
31. h15 3 3 Off o Ch16 3 4 Off Rotate A1 knob to advance through the four first level selections above 1 Chan 1 4 2 Chan 5 8 3 Chan 9 12 and 4 Ch 13 16 After making a selection press Menu to get additional selections specific to those channels see above Rotate A1 knob to switch between OFF and ON for Chs 1 5 9 and 13 A2 knob for Chs 2 6 10 and 14 A3 knob for Chs 3 7 11 and 15 and A4 knob for Chs 4 8 12 and 16 Audio Out Phase e Chan 1 4 o Ch1 1 1 Normal o Ch2 1 2 Normal o Ch3 1 3 Normal o Ch4 1 4 Normal e Chan 5 8 o Ch5 2 1 Normal o Ch6 2 2 Normal Publication 81 9059 0606 0 5 3 C uStream PESA FORTELDTV Main Menu Option Sub Menu Option amp Instructions for Changing Settings o Ch7 2 3 Normal o Ch 8 2 4 Normal e Chan 9 12 o Ch9 3 1 Normal o Ch10 3 2 Normal o Ch11 3 3 Normal o Ch 12 3 4 Normal e Chan 13 16 o Ch13 3 1 Normal o Ch14 3 2 Normal o Ch15 3 3 Normal o Ch16 3 4 Normal Rotate A1 knob to advance through the four first level selections above 1 Chan 1 4 2 Chan 5 8 3 Chan 9 12 and 4 Ch 13 16 After making a selection press Menu to get additional selections specific to those channels see above Rotate A1 knob to switch between Normal and Invert for Chs 1 5 9 and 13 A2 knob for Chs 2 6 10 and 14 A3 knob for Chs 3 7 11 and 15 and A4 knob for Chs 4 8 12 and 16 Bank Lvl ALC
32. he RGB e SD legalizer is used to legalize RGB Encoded and Luma Min Frm Delay Note Rotate knob under Min Frm Delay to select 0 1 or 2 frames Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards 4 15 C uStream PESA FORTELDTV Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards Output Cfg Output Configuration Choose this option to configure your HDFS 55X card s various Output settings Test Patterns e Pri Out Config e Sec Out Config e Genlock Source e Frame Rate e Encoder Mode Step Action 1 From the control panel s main menu screen press the small button next to Output Cfg second button down on the right hand side of the screen e The term Output Config appears in the middle of the screen e The following options are displayed on the screen o Test Patterns o Pri Out Config o Sec Out Config o Genlock Source Term Frame Connector in white lettering underneath o Frame Rate o Encoder Mode Term Test Bars in white lettering underneath 2 To check or set any of the options noted in step 1 refer to the table below Test Patterns a Press Test Patterns to activate the onboard test pattern generator b Press small button next to Enable to turn on feature c Rotate the blue knob below Pattern to select a desired pattern Pri Out Config Press Pri Out Config to access the following settings Timing Adjust
33. icates with its network then the cable must be good If both cables are good try another switch or hub Network traffic is best handled over a switch not a hub when multiple control panels and frames are to be installed e If you are using a hub try using a switch instead 6 e After a single RCP is able to communicate over the network substitute remaining RCPs for the first one one at a time using the same cable and switch path This will verify that each panel works with the frame e After ALL RCPs have been tested this way one at a time you are ready to connect multiple panels for the first time in this fault isolation process 7 Connect a second RCP in the same manner as the first to the Ethernet switch Verify that it communicates correctly with the Integrity system frame over the Ethernet Continue to add one RCP at a time verifying each before adding the next If adding an RCP causes the network to lockup so that other panels cannot continue to operate normally disconnect that panel and set it aside continuing with the next panel until all panels have either been successfully added or set aside 8 Those panels set aside in Step 7 may in fact be working panels but have an address conflict with another panel on the network This step provides the means for checking the address of each panel and how to change an address if it is causing a conflict 9 Each Integrity RCP has an IP address and MAC address that must be unique on that net
34. le is for the HDFS 551 and 552 cards The tables provide instructions on what knobs to use to set each option Configuring Audio Settings on HDFS 550 Card Main Menu Option Sub Menu Option amp Instructions for Changing Settings DeEmbed to DAS e Rotate A1 knob to switch between DeEmbed to DAS and Embed DAS Audio e Press Menu to select e Rotate A1 knob to change settings between None Grp 1 Grp 2 Grp 3 and Grp 4 Embed DAS Audio e Rotate A1 knob to switch between DeEmbed to DAS and Embed DAS Audio e Press Menu to select e Rotate A1 knob to change settings between None Grp 1 Grp 2 Grp 3 and Grp 4 Publication 81 9059 0606 0 5 1 C uStream PESA FORTELDTV Configuring Audio Settings on HDFS 551 and HDFS 552 Cards Main Menu Option Sub Menu Option amp Instructions for Changing Settings Output Sources e Chan 1 e IsSource AES1 1 e SumWith None e SumBalance 0 0 dB To change one of these four settings do the following Rotate A1 knob to change Channel Rotate A2 knob to change IsSource setting Rotate A3 knob to change SumWith setting Rotate A4 knob to change SumBalance setting AES Sources e 6AES 1 1 Ch 01 e AES 1 2 Ch 02 e AES 2 1 Ch 03 e AES 2 2 Ch 04 To change one of these four settings do the following Rotate A1 knob to change channel for AES 1 1 Rotate A2 knob to change channel for AES 1 2 Rotate A3 knob to change channel for AES 2 1 Rotate A4 k
35. ly with the safety regulations of the country in which they are to be installed Publication 81 9059 0606 0 Rev A vi Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream egenen Chapter 1 Introduction 1 1 HDFS 55X Cards Fortel DTV s HDFS 55X High Definition HD frame synchronizer cards are designed to support both HD SDI SMPTE 292M and SD SDI video formats It accepts an HD SMPTE 292M or 259M input to a local reference tri level or composite sync signal input When locked to a local reference it provides an infinite phasing adjustment window A video proc amp provides signal level adjustments in the component domain Y Cb Cr Black The DAS 441 Audio Synchronizer option provides control of embedded audio with gain mixing shuffling and delay adjustment This decoder generates a cleaner more accurate HD signal by eliminating quantizing errors and unwanted comb artifacts Its Perfect Palette Legalizer fixes gamma errors better by first analyzing what color it was supposed to be and then correctly adapting each pixel to a legal value without causing a hue shift while minimizing clipping effects There are independent settings for RGB Luminance and Composite thresholds The following are key features of HDFS 55X cards e Any input standard with auto detection 2X1 switch Second input can be used as AES input for HDFS 552 card Output HD SDI in SMPTE 292M Separate monitoring SDI down converted output N
36. nN ouran ON cscs ct see e eege seen 5 9 Publication 81 9059 0606 0 Rev A Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream roro Chapter SEN 6 1 Network Communication Errors cceccseseeeeeeseseeneeeeeeeeseeeeeeneeseseeeseeseseeeseseseeuseesseeuseeeseensaes 6 1 6 2 Recommended Network Configuration cccccsssseeccsseeeecssseeeenseeeeenseeneeeesasseeeenseeneeenseeenen 6 1 6 3 When Things Do Not Wolk ccceceseseeeeeeeseeeseseseeeseeeseeeseseseeeseeseseeeseseseeeseseseeuseeseneuseeeeseanes 6 2 N frames OF cards FOUN As edel 6 2 Selecting Ethernet cables 2s eege Edert ated ds tad teas de deEEg 6 3 Appendix A SNMP Error Reporting sssccccessrccssssscsscscccsccsccssssscsescsssscsssseeeses Aad Appendix B Installing Jumpers on HDFS 55X Cards ssccsesssscsssssecssesereeee B 1 Publication 81 9059 0606 0 Rev A iii Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream oer pre List of Figures Figure 1 HDFS 550 551 552 High Definition Frame Synchronizer Cards 1 2 Figure 2 HDFS 552 High Definition Frame Synchronizer Can 1 3 Figure 3 FRM 504 4RU High Density System Frame 1 4 Figure 4 RCP 502 Compact Remote Control Panel 1 4 Figure 5 RCP 503 Remote Control Panel 1 4 Figure 6 FRM 504 Integrity System Frame cccccssscsseceseceseceseceseeneeeseeeeeeeseeeeeseeeseecsaeeaeecaeceaeenseenaeens 2 1 Figure 7 FRM 501 Integrity System Frame
37. nd cable to be sure you do not have a defective one 3 Try another RCP If you have more than one RCP try each one in turn connected via the same crossover cable directly to the frame If other RCPs work then the problem has been isolated to a faulty control panel If no RCP works try another crossover cable again 4 After you have determined that an RCP is at fault set it aside and continue the tests with one or more good RCPs Now that an RCP communicates successfully over a crossover cable it is time to reconnect and test the rest of the network hardware Publication 81 9059 0606 0 6 2 C uStream PESA _ FORTELDTV Step Action 5 e Remove the crossover cable and connect one and only one RCP via an Ethernet patch cable to an Ethernet switch e Use a second Ethernet patch cable to connect the Ethernet switch to the Integrity frame Do not connect any other devices to the Ethernet switch at this time e Verify that the RCP is able to re establish communications with the frame over the Ethernet If not and we have verified that the frame and RCP communicate successfully via a crossover cable then the problem must be either a bad patch cable Ethernet switch or hub e Change cables and hubs to see if this corrects the problem The best way to verify the cable is correct substitute it for another known good patch cable in active use elsewhere in the facility If that device still commun
38. nob to change channel for AES 2 2 Chan Lvl Mute Ph Audio Out Level e Chan 1 4 o Ch1 1 1 0 0 dB o Ch2 1 2 0 0 dB o Ch3 1 3 0 0 dB o Ch4 1 4 0 0dB e Chan 5 8 o Ch5 2 1 0 0 dB o Ch 6 2 2 0 0 dB o Ch7 2 3 0 0 dB o Ch 8 2 4 0 0 dB e Chan 9 12 o Ch9 3 1 0 0 dB o Ch10 3 2 0 0dB o Ch11 3 3 0 0dB o Ch12 3 4 0 0dB e Chan 13 16 Ch 13 4 1 0 0 dB Ch 14 4 2 0 0 dB Ch 15 4 3 0 0 dB Ch 16 4 4 0 0 dB O O O Rotate A1 knob to advance through the four first level selections above 1 Chan 1 4 2 Chan 5 8 3 Chan 9 12 and 4 Ch Publication 81 9059 0606 0 Technical Manual HDFS 550 551 552 Frame Synchronizer Cards 5 2 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream egen Main Menu Option Sub Menu Option amp Instructions for Changing Settings 13 16 After making a selection press Menu to get additional selections specific to those channels see above Rotate Al knob to change the 0 0 dB settings for Chs 1 5 9 and 13 A2 knob for Chs 2 6 10 and 14 A3 knob for Chs 3 7 11 and 15 and A4 knob for Chs 4 8 12 and 16 Audio Out Mute e Chan 1 4 o Ch1 1 1 Off o Ch2 1 2 Off o Ch3 1 3 Off o Ch4 1 4 Off e Chan 5 8 o Ch5 2 1 Off o Ch6 2 2 Off o Ch7 2 3 Off o Ch8 2 4 Off e Chan 9 12 o Ch9 3 1 Off o Ch10 2 Off o Chll1 3 3 Off o Ch12 3 4 Off e Chan 13 16 o Ch13 3 1 Off o Ch14 3 2 Off o C
39. ore than two cards be inserted in the frame 1 Carefully load cards through the rear of the frame see diagram below for slot numbers for placing the card in the frame 2 Card guides at the sides of each slot are used to align the card with the mating connector on the mid plane card as the card is inserted fully into the frame 3 After the card is seated into the mating connector secure the card using the two captive screws Figure 7 FRM 501 Integrity System Frame Publication 81 9059 0606 0 2 2 Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards Coustream Chapter 3 Connecting a Card to External Systems 3 1 Introduction This chapter presents details on the following for each HDFS 55X card e Number of inputs and outputs on each card e Graphic showing the connectors on the card along with a description of what is attached to each connector e Supported input and output formats 3 2 HDFS 55X Card s Inputs Outputs The following table provides a brief description of each of the three HDFS 55X cards as well as a list of each card s input and output connectors Card Description Inputs Outputs HDFS 550 High Definition Frame e 2HD SDI Inputs Synchronizer Card with outputs e 2 HD Outputs e SDI e 3 SDI Outputs e PAL e Genlock HDFS 551 High Definition Frame e 2HD SDI Inputs Synchronizer Card with outputs e 2 HD Outputs e SDI e 2SD Outputs 2 Selectable SD or NTSC e
40. otate blue knob immediately below to make those changes Those changes will now be recorded for your selected channel Press the small square button next to AES Out Sources and the following screen example appears FS 552 Audio AES Output Select output ch for each AES ch AES 1 1 AES 1 2 AES 2 1 AES 2 2 Ch 01 Ch 01 Ch 01 Ch 01 e Rotate blue knobs below each of the four settings across the bottom of the screen to change the channel number for each of the four AES channels AEN II AES 1 2 AES 2 1 and AES 2 2 Publication 81 9059 0606 0 5 11 uStream ao TE Technical Manual C HDFS 550 551 552 Frame Synchronizer Cards ALC From the Configuration screen press the small square button next to ALC and the following screen example appears Bank 1 ALC Bank Config FS 552 Bank 2 ALC ALC Config Bank 3 ALC Bank 4 ALC Banks From the ALC Config screen press the small square button next to Bank 1 ALC Bank 2 ALC Bank 3 ALC or Bank 4 ALC and the following screen example appears Note The following instructions are applicable for all four Banks ALC Off Lim Off FS 552 Audio ALC Bank ALC Peak Limiter Level Rate Level Rate 0 0 dBFS 0 0 0 dBFS 0 e Press the small square button next to ALC to switch its setting between Off and On e Press the small square button next to Lim Limiter to switch its setting between Off an
41. output based on a decimation of the primary output e One AES pair selectable from any embedded audio group a separate choice from Option A Genlock An optional source for a Genlock reference that may be used instead of the frame Genlock Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards 3 2 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream weg FORTELDTV 3 4 Input and Output Formats Input Formats Supported by HDFS 55X Cards The table below lists the input formats supported by HDFS 55X cards Input Formats 5251 5994 720p 59 94 1035i 59 94 1080i 59 94 625 50 720p 50 1080i 50 1080i 50 295 Output Formats Supported by HDFS 55X Cards The table below lists the output formats supported by HDFS 55X cards Output Formats With NTSC With PAL Reference Reference SD 525 SD 625 4871 59 94 720p 50 720p 59 94 10801 50 10801 59 94 Publication 81 9059 0606 0 3 3 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream PESA FORTELDTV Chapter 4 Configuring a Card s Video Settings 4 1 Introduction This chapter presents step by step instructions for configuring an HDFS 55X card s Video settings using Fortel DTV s RCP 502 and RCP 503 remote control panels Chapter 5 provides instructions for configuring Audio settings 4 2 RCP 502 Compact Remote Control Panel Video Figure 9 RCP 502 Compact
42. panel s main menu screen listing the Video Config options rotate A1 knob until Jnput is highlighted on the screen and press Menu The following is an example of information displayed upon selecting nput Video Input OnVidLoss Off Input Sel Input 1 Input 1 SD525 59 94 For OnVidLoss rotate A1 knob to select a preferred option when there is a loss of video to the card The following options are offered Off Freeze Black Timeout Switch Input Rotate A2 knob to switch both displayed settings of Input 1 to Input 2 or vice versa Press Take Enter to save your settings Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards 4 4 C uStream PESA Output Output Configuration FORTELDTIV Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards Choose this option to configure your HDFS 55X card s various Output settings Step Action l With the control panel s main menu screen listing the Video Config options rotate A1 knob until Output is highlighted on the screen and press Menu The following is an example of information displayed upon selecting Output e Primary Output e Sec AspRatio e HD Config e SD Config e Genlock Source e Frame Rate e Test Pattern e Encoder Mode 2 Rotate A1 knob to switch between any of the eight 8 options listed in step 1 3 To check or set any of the options noted in step 1 refer to the ta
43. roc Amp settings to their default values press the small button next to Reset Procs bottom left hand side of the screen Publication 81 9059 0606 0 4 14 C uStream PESA FORTELDTV VidProcess Video Processing Choose this option to check or configure the your cards various Video Processing options Color Corrector Legalizers Min Frm Delay Step Action 1 From the control panel s main menu screen press the small button next to VidProcess top button on the right hand side of the screen e The term Video Processing appears in the middle of the screen e The following three 3 options settings are also displayed on the screen o Color Correct o HD and SD Legalizers o Min Frm Delay To check or set any of the three 3 options noted in step 1 refer to the table below Color Corrector e If this option is not enabled the menu will be grayed out e If this option is enabled the Color Correct menu will be lit up in yellow and you can change the following color values for the card o White Balance o Black Balance o Gamma o Black Level Stretch To reset color values to unity press Set CC to Unity e To store up to eight Color Correct preset settings press CC Memories You can save the settings to a memory location Later you can recall a stored setting from memory Legalizers There are separate legalizers for the HD and SD outputs e HD legalizer is used to legalize t
44. set Reset User Controls Press TAKE Ready Note The word TAKE on a screen refers to the Take Enter button 2 Press Take Enter to save your settings Change Mode Note This option is not available with the HDFS 55X card Publication 81 9059 0606 0 4 9 C uStream roro Card Info Choose this option to view the Card Info for your HDFS 55X card Step Action 1 With the control panel s main menu screen listing the Video Config options rotate A1 knob until Card Info is highlighted on the screen and press Menu The following is an example of information displayed upon selecting Card Info CARD INFO Card Type c 0 1 4 6 2006 11 28 ude error vid1 2006 11 01 vid2 2006 1 1 22 vid3 2006 12 18 aud 2006 08 04 Press Back to return to the main menu screen and rotate A1 knob to select another option Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards 4 10 C uStream PESA FORTELDTV Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards 4 3 RCP 503 Remote Control Panel Video After powering up the RCP 503 control panel and selecting the HDFS 55X card to be configured the control panel displays eight options on its main menu screen related to Video settings Eight small square buttons to the left and right of the main menu screen four on one side of the screen and four on the opposite side of the
45. sion do not operate this equipment in an explosive atmosphere unless it has been specifically certified for such operation e Have qualified personnel perform safety checks after any completed service e To reduce the risk of electric shock ensure that the two power supply cords if so equipped are each plugged into a separate branch circuit e If equipped with a redundant power supply this unit has two power cords To reduce the risk of electric shock disconnect both power supply cords before servicing Publication 81 9059 0606 0 Rev A v Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream egenen Cautions e This equipment contains static sensitive components Use anti static grounding equipment whenever handling or servicing modules and components When circuit modules are removed from the frame place them on a flat static controlled surface Failure to follow this precaution can result in component damage due to electrostatic discharge e To prevent damage to equipment when replacing fuses locate and correct the trouble that caused the fuse to blow before applying power Verify that all power supply LEDs are off before removing the power supply or servicing equipment Use only specified replacement parts Follow static precautions at all times when handling this equipment Leave the back of the frame clear for air exhaust cooling and to allow room for cabling Slots and openings in the cabinet are provided
46. tions used in setting a new Alias Name appear in the lower left hand corner of the screen Change Position and Change Letter Note A card name can contain up to eight 8 letters digits 3 Rotate blue knob immediately below Change Position to move left or right through the letters digits of the card s current name Note The letter that will be changed is displayed in white The other letters are blue 4 After selecting a letter digit of the current name that you wish to change rotate blue knob immediately below Change Letter until a selected letter digit is displayed 5 Repeat steps 3 and 4 until a new name has been selected 6 Press the small button next to reset top button on the right hand side of the screen to reset the alias back to the factory default Reset Procs Reset the Proc Amp Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards Choose this option to reset your HDFS 55X card s Video Processing Amplifier Proc Amp Control settings e Gain e Black Level e Chroma Level e NTSC Hue Step Action 1 With the control panel s main menu screen displayed the Proc Amp settings appear along the bottom of the screen and the blue knobs below the screen are used for changing the settings Rotate a blue knob below one of the four settings GAIN BLACK CHROMA HUE to change the setting Note The four Proc Amp settings are always displayed along the bottom of the main menu screen 2 If you wish to return the P
47. uStream PESA FORTELDTV Proc Controls Choose this option to set or change your HDFS 55X card s video processing control settings HUE GAIN BLACK CHROMA Step Action 1 With the control panel s main menu screen listing the Video Config options rotate the A1 knob until Proc Controls is highlighted on the screen and press Menu The following is an example of information displayed upon selecting Proc Controls Video Proc Controls HUE 0 0 deg GAIN 100 0 BLACK OmV CHROMA 100 0 Depending on which control you wish to set or change rotate one of the following knobs to make your selection e Al HUE e A2 GAIN e A3 BLACK e A4 CHROMA Press Take Enter to save your settings Press Preset to return to default settings Publication 81 9059 0606 0 Technical Manual HDFS 550 551 552 Frame Synchronizer Cards 4 7 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards uStream Parent FORTELDTV Color Corrector Choose this option to set or change your HDFS 55X card s color settings Step Action l With the control panel s main menu screen listing the Video Config options rotate A1 knob until Color Corrector is highlighted on the screen and press Menu The following is an example of information displayed upon selecting Color Corrector Color Corrector Rotate SEL knob Preset button for Unity Note The SEL knob is also
48. with HDFS Card Info Card Type DTV s RCP 502 Compact Remote Control Panel User Manual January 2005 and S For more detailed information on the RCP 502 and RCP 503 Control Panels see Fortel 2 RCP 503 Remote Control Panel User Manual Revision No 1 01 June 2004 Publication 81 9059 0606 0 4 2 C uStream PESA FORTELDTV Status amp Alarms Choose this option to determine the following about your HDFS 55X card e What is the card s Temperature and its Over Temperature Threshold e Is the card getting any Errors e Does the card have any active Major or Minor Alarms e Is there an Input Error Step Action 1 With the control panel s main menu screen listing the Video Config options rotate A1 knob until Status amp Alarms is highlighted on the screen and press Menu The following is an example of information displayed upon selecting Status amp Alarms 40 0C OvrTempThr knob 55 0 ErrorSecs TAKE 0 Major Alrm NoVidLock Minor Alrm AudInErr UDC Alrm NA Rotate A1 knob to reset the OvrTempThr setting to a higher or lower setting Press Take Enter to save your settings Publication 81 9059 0606 0 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards 4 3 C uStream PESA FORTELDTV Input Input Configuration Choose this option to select the type of input you want to use nput 1 or Input 2 Step Action 1 With the control
49. work Make sure each of the selected IP addresses are unique on the network The MAC addresses are factory programmed and cannot be changed Selecting Ethernet cables Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards There are varieties of cables with RJ 45 connectors on the ends in the marketplace Integrity system products use Ethernet patch cables when connected through a switch or hub and crossover cables when connected one to one without a switch or hub Cables should be compliant with IEEE 802 3 specifications Publication 81 9059 0606 0 6 3 C uStream PESA FORTELDTV Appendix A This appendix presents a list of items related to the HDFS 55X card that are available for Simple Network SNMP Error Reporting Management Protocol SNMP information and error reporting Item Description cardType One of nine card types FS UDC UCP x 550 551 552 etc cardAlias User assigned name string cardRev Software version cardTemp Card temperature in degrees Celsius overTempAlarm Card temperature greater than the threshold User defined setting that defaults to 55 degrees Celsius refAlarm Loss of Genlock vidAlarm Loss of input video vidInSel e 0 Input 1 e _1 Input 2 majorAlarm e 0 OK e 1 OverTemp e 2 NoVidLock e 3 NoRefLock e 4 UDC Error minorAlarm e 0 OK e 2 AudioError BadCSB or BadRxLock Publication 81 9059 0606 0 Technical Manual HDFS 550 55
50. xt to Grp 2 Ch 05 Ch 08 now appear on the screen e Repeat this process for Grp 3 and Grp 4 Mute e With Grp 1 selected press the small square button next to Mute o The settings under Ch 01 Ch 04 along the bottom of the screen change from 0 0 dB to Off o Rotate blue knob below any one of the channels and the channel switches back and forth between Off and On Publication 81 9059 0606 0 5 7 Technical Manual HDFS 550 55 1 552 Frame Synchronizer Cards C uStream PESA FORTELDTV e To repeat this process for Grp 2 press the small square button next to Grp 2 Ch 05 Ch 08 now appear on the screen e Repeat process for Grp 3 and Grp 4 Bank Gain Bank Gain settings are independent of settings for Grp 1 Grp 2 Grp 3 or Grp 4 From the main menu screen press the small square button next to Bank Gain The following is an example of the screen that appears Reset All Audio Bank Config Gains FS 552 Bank Gain Bank 1 Bank 2 Bank 3 Bank 4 0 0 dB 0 0 dB 0 0 dB 0 0 dB The Bank Gain function allows you to divide up the system s 16 audio channels into four banks Bank 1 Bank 2 Bank 3 and Bank 4 This feature is useful for quickly setting audio levels for multiple channels simultaneously For example because of a particular hardware setup you may want to have Channels 1 6 set up in Bank 1 Channels 7 and 8 set up in Bank 2 Channels 9 11 in Bank 3 and Channels 12 16 in Bank 4 Complete
Download Pdf Manuals
Related Search
fortel_hdfs 55x_signal_processor_manual_rev_a