Home

User Manual QME

Contents

1. User Manual QME 2200 Series Ver 1 0 Jan 2008 Regional EMC Compliance Information FCC Verification Notice USA only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Class A to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful F equipment has been tested and found to comply with the limits for a Class A digital device pursuant interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense INDUSTRY CANADA Canada only This Class B or Class A if so indicated on the registration label digital apparatus meets the requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la Classe B ou Classe A si ainsi indiqu sur l tiquette d enregistration respecte toutes les exigences du Reglement sur le Materiel Broui
2. The fail safe settings default values are not demanding so a system should be able to operate with the fails safe settings even if it is installed with slower memory chips or other kinds of low performance components 42 Chapter 3 BIOS BIOS Check Point and Beep Code List Definition of Beep Codes Beep codes are used by the BIOS to indicate a serious or fatal error to the end user Beep codes are used when an error occurs before the system video has been initialized Beep Codes are generated by the system board speaker commonly referred to as the PC speaker Beeps Error message Description 1 Refresh Failure The memory refresh circuitry on the motherboard is faulty 2 Parity Error Parity error in the first 64 KB of memory 3 Base 64 KB Memory Failure Memory failure in first 64 KB 4 Timer Not Operational Memory failure in the first 64 KB of memory or Timer 1 on the M B is not functioning 5 Processor error The CPU Central Processing unit on the M B generated an error 6 8042 Gate A20 Failure The keyboard controller 8042 may be bad The BIOS cannot switch to protected mode Processor Exception Interrupt Error The CPU generated an exception interrupt Display Memory Read Write Error The system video adapter is either missing or its memory is faulty This is not a fatal error 9 ROM Checksum Error The ROM checksum value does not match the value encoded in the BIOS 10 CMOS Shutdown Register The shut
3. 39 Initializes DMAC 1 amp DMAC 2 3A Initialize RTC date time 3B Test for total memory installed in the system Also Check for DEL or ESC keys to limit memory test Display total memory in the system 3C Mid POST initialization of chipset registers 40 Detect if different devices parallel ports serial ports CPU coprocessor etc has successfully installed on the system and update the BDA EBDA etc 50 Programming the memory hole or any kind of implementation that needs an adjustment in system RAM size if needed 52 Updates CMOS memory size from memory found in memory test Allocates memory for Extended BIOS Data Area from base memory 60 Initializes NUM LOCK status and programs the KBD typematic rate 75 Initialize Int 13 and prepare for IPL detection 78 Initializes IPL devices controlled by BIOS and option ROMs 7A Initializes remaining option ROMs 7C Generate and write contents of ESCD in NVRam 84 Log errors encountered during POST 85 Display errors to the user and gets the user response for error 87 Execute BIOS setup if needed requested 8C Late POST initialization of chipset registers 8D Build APM tables if APM is supported 8b Program the peripheral parameters Enable Disable NMI as selected 90 Late POST initialization of system management interrupt AO Check boot password if installed A1 Clean up work needed before booting to OS A2 Takes care of runtime image preparation for different BIOS modules F
4. Chapter 5 Using the Client Full Screen Display on Console PC The Java Remote KVM enables you to display the redirected video image in full screen as seen at the local side server in place of the window at the remote server side To display full screen 1 Click Control on the main menu bar 2 Select Enable Full Screen Mode BB eve KV Fie View Help Video Quality HotKey Stma Com 2 re ae aiin a To return to normal view 1 Click Control on the main menu bar 2 Select Disable Full Screen Mode 79 Chapter 5 Using the Client Dynamic Scaling Video Resolution From managed server power on to entering the Operating System the video output resolution changes frequently The AST2000 detects these changes and adjusts the display window automatically In addition user can adjust the display window to the size required by clicking and dragging the bottom right hand corner of the inner window Before using dynamic scaling video resolution function please make sure that the state of the video resolution mode is set to Fit mode and Not Scroll Mode Select the Control menu as shown in the following image Ensure that the Scroll Mode option is visible In this state the video resolution state is currently in Fit Mode Color Text Adjust If AST2000 displays blurred color text in some situations adjust the Color Text Value to improve clarity Win
5. Fault LED Status Power Statu On Cm iTem OK Temperature Stotus RUZ Temp Disabled e Fault LED Status indicates whether the fault LED on the server is on or off e Power Status indicates whether the server system is powered on or off Update e Fan Status indicates the health status of the CPU fans and SYS fans for CPUs and SYS that are in stalled e Temperature Status indicates the status for such items as the baseboard and processor temperature and thermal control e Voltage Status indicates the voltage status for components such as the baseboard processor Vcc and CPUs installed Click Update to refresh the status information 57 Chapter 4 Using the Web UI Chassis Intrusion Displays Chassis open close status Description Chassis Intrusion Status closed Fan Click the Fan tab to view CPU and SYS fan information Embedded Server Manager system information Coniguraton UserManayement Remote Control Maintenance SencorReading EwentLoge Locator Summary Chassis Intrusion Fan 1CPU Fant CPU Fan SYS Fant ISVS Fan Indicator Fault LED Temperature Voltage Temperature Click the Temperature tab to view system component temperature information Description CPU Fant Lower critical threshold is readable 1025 SensorRescina 2160 Status ok ToP Description CPU Fanz Lower critical threshold i
6. KVM stands for Keyboard Video and Mouse KVM over IP redirects server video screen keyboard and mouse data to or from a remote console PC via a network so that the administrator can monitor the server and control keyboard and mouse to operate the server remotely KVM Client HW platform requirement RKVM application needs CPU resource to decode the video and draw the screen picture so we suggest CPU Pentium4 1 8G and 512 dram to run otherwise the Client Application will timeout and disconnect from BMC Video Screen Redirection AST2000 captures video output compresses and sends it to a remote console PC with encryption The Java re mote KVM application on the console PC receives and displays the server s video screen AST2000 can acquire video source either from PCI bus as VGA mode or from external source as Video mode Please refer to hardware specification for more detail information about mode switching The redirection specifications are as follows Video Mode Support both Text mode and Graphic mode Frame Resolution Up to 1280x1024 75Hz Frame Frequency Up to 85Hz for other resolutions Frame Transfer Rate More than 30 frames per second for generic operation Video Quality Configuration In order to fit the network bandwidth and video quality requirement the Java Remote KVM provides the follow ing options that the user can select them Video Quality Option 1 Best Fewest video loss and biggest size image transmi
7. Memory Controller Intel ESB2 E South Bridge IO Bridge Flash ROM for System BIOS SILICON SST49LF008A 33 4C NHE Super IO Winbond 87427 VGA AST2000 SMIT712 option NIC 82563 BMC AST2000 SAS Controller LSI1068E option Clock generator Buffer ICS9328421BGLFT ICS9DB803DFLFT ICS9FG1201 CGLF T Chapter 1 Introduction Serverboard Components SATA SKU 2 345 nn SSS oJ 0 EEEF 4 Fin ll O kH o ELA CEE F EERO ac Eo mE E r O dg O 19 o ESS 18 L i 17 N 16 mu 15 14 SS i E a T r r r Tr 1 13 12 Item Label Component 1 I O ports See Input Output Ports on page 4 2 MAIN PWR Serverboard main power connector 3 IPMB connector Reserve power supply connector 4 12V connector Supports 12V power connection 5 DDR2 DIMM array 4 DDR2 DIMM slots channels 2 and 3 6 CPU 1 socket 771 pin CPU 1 socket for processor 7 CPU 2 socket 771 pin CPU 2 socket for processor 8 USB connector Front USB connector 9 CPU PWR1 CPU 1 power connector 10 CPU PWR2 CPU 2 power connector 11 PRIMARY IDE Primary IDE connector 12 SATA Connectors 6
8. changes 39 Chapter 3 BIOS Remote Access Configuration Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Serve Configure Remote Access type and parameters Select Remote Access type Remote Access Enabled Serial port number COM1 Base Address IRQ 3F8h 4 Serial Port Mode 115200 8 n 1 Flow Control None Redirection After BIOS POST Always lt Select Screen Terminal Type ANSI Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Remote Access this item enables disables serial port remote access Serial port number select the serial port number Base Address IRQ select base address IRQ Serial Port Mode Select serial port settings Flow Control options are None default Hardware or Software Redirection After BIOS POST options are Always default Boot Loader or Always Terminal Type options are ANSI default VT100 or VT UFT8 40 Chapter 3 BIOS Security Menu This page enables you to set the security parameters Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Main Advanced Boot Server EGtatgy Exit Security Settings Install or Change the password Change Supervisor Password Change User Password Boot Sector Virus Protection Disabled lt Select Screen Select Item Enter Change
9. 1 Cache memory bad Troubleshooting BIOS Beep Codes The following table describes the beep codes used for troubleshooting Number of Beeps Troubleshooting Action 1 20r3 Reseat the memory or replace with known good modules 4 7 9 11 Fatal error indicating a serious problem with the system Consult your system manufacturer Before declaring the motherboard beyond all hope eliminate the possibility of interference by a malfunctioning add in card Remove all expansion cards except the video adapter If the beep codes are generated even when all other expansion cards are absent the motherboard has a serious problem Consult your system manufacturer If the beep codes are not generated when all other expansion cards are absent one of the add in cards is causing the malfunction Insert the cards back into the system one at a time until the problem happens again This will reveal the malfunctioning add in card 8 If the system video adapter is an add in card replace or reseat the video adapter If the video adapter is an integrated part of the system board the board may be faulty Chapter 3 BIOS Error Message Descriptions Memory Message Displayed Description Gate20 Error The BIOS is unable to properly control the motherboard s Gate A20 function which controls access of memory over 1 MB This may indicate a problem with the mother board Multi Bit ECC Error This message will o
10. BIOS Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY PCI Configuration LAN Controller 0 LANO OptionROM LAN Controller 1 LAN1 OptionROM LSI SAS 1068E Enabled Enabled Enabled Enabled Enabled Enable or Disable LAN Controller 0 lt Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Note Default values shown ing message Not enough Space to copy PCI Option ROM during POST if the wo Standard PCI Option ROM space is only 128KB BIOS displays the following warn system total option size is over the 128K limitation Initial requirements for certain add on cards and onboard devices that call option ROM such as NIC Option ROM may need to have the function disabled to allocate sufficient space LAN Controller 0 Select LANO mode from Enabled or Disabled LAN Controller 1 Select LANI mode from Enabled or Disabled LSI SAS Select LSI SAS mode from Enabled or Disabled This item is only displayed on SAS SKUs 29 Chapter 3 BIOS MPS Configuration Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY MPS Configuration Select MPS Revision MPS Revision 1 4 lt Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61
11. O System Information System Monitoring User Management Remote Contro Maintenance FronPanel Lockout Network E mail Notification Platform Event Filter Clock Settings System Management Access Front Panel Lockout T Lock out Reset button T Lock out power button for Power off only Front Panel Lockout The administrator can control the front panel lockout here including Locking out the Reset button and Locking out the power button for power off only Front Panel Lockout 7 Lock out Reset button TF Lock out power button for Power off only Network l Click the Network tab to set network parameters Embedded Server Manager Systemnformation System Monitoring Configuration User Management Remote Contro Maintenance Network E mailNolficetion Platform Event Fiter ClockSetings System Management Access Network E Erebie nece e Enable DHCP check this box to enable the DHCP server When checked an IP address is automatically assigned IP enter a specific IP address to be assigned Net Mask enter the Net Mask of the LAN Gateway enter the Gateway of the LAN Mac Address this field displays the Mac address DNS server enter the DNS server address of the LAN if required Click Submit to save the changes ie 62 Chapter 4 Using the Web UI E mail Notification T
12. Session Time Out 1 Click the Session Time Out tab Embedded Server Manager o te System Monitoring Configuration User Management RemoteContol Maintenance Versions Session Time Out Components Tineout Enab Tineout C disable Timeout activity timeout far this session is inactive for the selected time you will be lugged out Sosson Tina 15 min 2 Click Enable Timeout and select a timeout value from the drop down list as seen in following image 15 minutes 30 minutes 1 hour 3 Click Disable Timeout to prevent the embedded session time web server from logging off 4 Click Submit to save the changes 55 Chapter 4 Using the Web UI Components Click the Components tab to view CPU and memory information CPU Click the CPU tab to view the CPU model speed and number Embedded Server Manager sninformation System Monitoring Configuration User Management Remate Control Maintenance Versions Session Time Out Components CPU memon Menu 1teuo Doseripton CPU information cn o Em Enable Socket c un Manufacturer tel Model Unknown Frequency dessen Tor Memory Click the Memory tab to view memory model size DIMM slot status and slot location Embedded Server Manager System information System Monitoring Configuration User Management Remote Control Maintenance CPU memoy Menu DI
13. The 8259 interrupt controller is initialized L1 cache is enabled E9 Set up floppy controller and data Attempt to read from floppy EA Enable ATAPI hardware Attempt to read from ARMD and ATAPI CDROM EB Disable ATAPI hardware Jump back to checkpoint E9 EF Read error occurred on media Jump back to checkpoint EB E9 or EA Determine information about root directory of recovery media FO Search for pre defined recovery file name in root directory F1 Recovery file not found F2 Start reading FAT table and analyze FAT to find the clusters occupied by the recovery file F3 Start reading the recovery file cluster by cluster F5 Disable L1 cache FA Check the validity of the recovery file configuration to the current configuration of the flash part 44 Chapter 3 BIOS Checkpoint Description FB Make flash write enabled as specified by the chipset and OEM Detect proper flash part Verify that the found flash part size equals the recovery file size F4 The recovery file size does not equal the found flash part size FC Erase the flash part FD Program the flash part FF The flash has been updated successfully Make flash write disabled Disable ATAPI hardware Restore CPUID value back into register Give control to F000 ROM at F000 FFFOh POST Code Checkpoints The POST code checkpoints are the largest set of checkpoints during the BIOS pre boot process The following table describes the type of
14. 10 CPU PWR2 CPU 2 power connector 11 PRIMARY IDE Primary IDE connector 12 SAS Connectors 8 x SAS connectors 13 FRONT PANEL Front panel connector 14 PCI Slot 1 PCI slot supporting PCI X 64 100 15 PCI Slot 2 PCI slot supporting PCI X 64 133 16 PCI E Slot 3 PCI E slot supporting PCI E x 4 17 PCI E Slot 4 PCI E slot supporting PCI E x 4 18 PCI E Slot 5 PCI E slot supporting PCI E x 16 19 DDR2 DIMM array 4 DDR2 DIMM slots channels 0 and 1 Chapter 1 Introduction Input Output Ports The QME 2200 Hybrid board is installed with the following I O ports Refer to the illustration below SLE j O EI E EJ 12345 678 9 10 PS 2 Mouse Connect a PS 2 pointing device to this port PS 2 Keyboard Connect a PS 2 keyboard to this port 3 ID button rear Press to light front and rear ID LEDs see table below for behavior ID LED 4 Status LED Behavior is controlled by BMC see below for behavior LED Name Color Condition Occurrence ID LED Blue off OK Blinking ID button pressed on chassis Status LED Amber Solid Critical failure such as critical fan voltage or temperature state Blinking Non critical failure such as non critical fan volt age temperature state or CPU thermal trip Green Solid OK 5 USB Ports Use the USB ports to connect USB devices 6 VGA Port Use the VGA port to connect
15. F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Supervisor Password displays whether the supervisor password is installed or not User Password displays whether the user password is installed or not Change Supervisor User Password you can install a Supervisor password and if you install a supervisor pass word you can then install a user password A user password does not provide access to many of the features in the Setup utility If you highlight these items and press Enter a dialog box appears which lets you enter a password You can enter no more than six letters or numbers Press Enter after you have typed in the password A second dialog box asks you to retype the password for confirmation Press Enter after you have retyped it correctly The password is re quired at boot time or when the user enters the Setup utility Boot Sector Virus Protection Enable and disable Boot sector protection 41 Chapter 3 BIOS Exit Menu Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Main Advanced Boot Server Security B Exit Options Exit system setup After saving the changes Save Changes and Exit Discard Changes and Exit F10 key can be used Discard Changes for this operation Load Optimal Defaults Load Failsafe Defaults lt Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and
16. Mirrored Mode and Mirrored Mode The memory upgrade granularity is one DIMM Chapter 2 Installing Hardware Installing a PCI Card See Serverboard Components on page 2 for the location of the PCI slots CAUTION VOLTAGES CAN BE PRESENT WITHIN THE SERVER WHENEVER AN AC POWER SOURCE IS CONNECTED THIS VOLTAGE IS PRESENT EVEN WHEN THE MAIN POWER SWITCH IS IN THE OFF POSITION ENSURE THAT THE SYSTEM IS POWERED DOWN AND ALL POWER SOURCES HAVE BEEN DIS CONNECTED FROM THE SERVER PRIOR TO INSTALLING A PCI CARD FAILURE TO OBSERVE THIS WARNING COULD RESULT IN PERSONAL IN JURY OR DAMAGE TO EQUIPMENT Follow these instructions to install a PCI card 1 Remove a blanking plate from the system case 2 Install the PCI card into the expansion slot 3 Secure the metal bracket of the PCI card to the system case with a screw 16 Chapter 3 BIOS Setup Menu The computer employs the latest AMI BIOS which is stored in a CMOS chip This CMOS chip contains the ROM Setup instructions for configuring the mainboard s BIOS The BIOS Basic Input and Output System Setup utility is a menu driven utility that enables you to make changes to the system configuration and tailor your sys tem to suit your individual work needs BIOS is a ROM based configuration utility that displays the system s configuration status and provides you with a tool to set system parameters These parameters are stored in non volatile battery backed up CMOS RAM
17. Password Managing Users ADS Configuration Remote Control Redirection Remote Power Control Hotkey Setup Maintenance Firmware Upgrade Reset BMC CHAPTER 5 Using the Client Video Screen Redirection Video Quality Configuration Video Quality Option USB Keyboard and Mouse Emulation Mouse Synchronization at Console Side Hide Console Side Mouse Hardware Cursor Mode Keyboard LED and Status Synchronization Hot Key Simulation Full Screen Display on Console PC Dynamic Scaling Video Resolution Color Text Adjust Encryption Mode Virtual Storage Mounting a Device USB DVD Emulation USB Floppy Emulation USB CD ROM Emulation USB Flash Disk Emulation CD DVD ROM Emulation Multidevice Configuration Virtual Storage Configuration Linux Kernel 2 4 APPENDIX A Updating the BMC Firmware BMC Firmware Update Utility BMC Firmware Update Procedure APPENDIX B Specifications SKU Information vii 52 52 52 52 53 53 35 56 57 57 59 61 61 62 62 62 63 63 63 64 66 66 67 68 69 69 72 72 73 73 73 74 74 74 74 74 75 76 77 77 77 78 79 80 80 81 81 81 83 83 84 84 84 85 86 87 87 87 87 88 88 89 viii Chapter 1 Introduction The QME 2200 is an extended ATX server board that measures 13 x 12 inches 333 mm x 305 mm The QME 2200 features dual J Type 771 pin sockets that accommodate single or dual Intel amp Xeon Dempsey Woodcrest Wolfdale Clovertown Harpertown 5000 5100 52
18. V02 61 Copyright 1985 2006 American Megatrends Inc Note dw Current MAC address in BMC is dynamic and may change with configuration changes 37 Chapter 3 BIOS Set Subnet Mask Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY LETS EDIT IE IST M Server 1 1 D 1 Enter Subnet Mask in Subnet Mask Configuration decimal in the form of XXX XXX XXX XXX XXX less than 256 Parameter Selector 06 and decimal only Subnet Mask 255 255 255 000 Current Subnet Mask in BMC 255 255 255 000 lt Select Screen Select Item F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Note dw Current Subnet Mask in BMC is dynamic and may change with configuration changes 38 Set Gateway Configuration Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Main Advanced Boot M Server Security Exit GateWay Configuration Parameter Selector 0C GateWay Address 192 168 077 001 Current Gateway in BMC 192 168 077 001 Chapter 3 BIOS Enter Gateway Address in decimal in the form of XXX2OOCXXX XXX XXX less than 256 and decimal only lt Select Screen Select Item F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Note dw Current Gateway address in BMC is dynamic and may change with configuration
19. an ATAPI com patibility test This message is typically displayed when the BIOS is trying o detect and configure IDE ATAPI devices in POST Secondary Master Drive ATAPI Incompatible The IDE ATAPI device configured as Secondary Master failed an ATAPI compatibility test This message is typically displayed when the BIOS is rying to detect and configure IDE ATAPI devices in POST Secondary Slave Drive ATAPI Incompatible The IDE ATAPI device configured as Secondary Slave failed an ATAPI compatibility test This message is typically displayed when the BIOS is rying to detect and configure IDE ATAPI devices in POST S M A R T Capable but Command Failed The BIOS tried to send a S M A R T message to a hard disk but the command transaction failed This message can be reported by an ATAPI device using the S M A R T error reporting standard S M A R T failure messages may indicate the need to replace the hard disk S M A R T Command Failed The BIOS tried to send a S M A R T message to a hard disk but the command transaction failed This message can be reported by an ATAPI device using the S M A R T error reporting standard S M A R T failure messages may indicate the need to replace the hard disk S M A R T Status BAD Backup and Replace A S M A R T capable hard disk sends this message when it detects an imminent failure This message can be reported by an ATAPI device using the S M A R T
20. on some systems when no bootable device can be detected Chapter 3 BIOS Storage Device Message Displayed Description Primary Master Hard Disk Error The IDE ATAPI device configured as Primary Master could not be prop erly initialized by the BIOS This message is typically displayed when the BIOS is trying to detect and configure IDE ATAPI devices in POST Primary Slave Hard Disk Error The IDE ATAPI device configured as Primary Slave could not be properly initialized by the BIOS This message is typically displayed when the BIOS is trying to detect and configure IDE ATAPI devices in POST Secondary Master Hard Disk Error The IDE ATAPI device configured as Secondary Master could not be properly initialized by the BIOS This message is typically displayed when the BIOS is trying to detect and configure IDE ATAPI devices in POST Secondary Slave Hard Disk Error The IDE ATAPI device configured as Secondary Slave could not be prop erly initialized by the BIOS This message is typically displayed when the BIOS is trying to detect and configure IDE ATAPI devices in POST Primary Master Drive ATAPI Incompatible The IDE ATAPI device configured as Primary Master failed an ATAPI compatibility test This message is typically displayed when the BIOS is rying to detect and configure IDE ATAPI devices in POST Primary Slave Drive ATAPI Incompatible The IDE ATAPI device configured as Primary Slave failed
21. password prevent user access change user privi leges or delete the user Embedded Server Manager Se System information System Monitoring Configuration User Management Remote Control Maintenance UserAccount ADS Configuration User List Username Privilege Status root administrator enabe __Change Password Nova user enable Disable J Change Password _ __Change Privilege Delete Disable Click to prevent the user access to the server e Change Password Click to change the user s password e Change Privilege Click to change the user s privileges e Delete Click to remove the user from the system 67 Chapter 4 Using the Web UI ADS Configuration The ADS Configuration web page enables the administrator to configure an Active Directory Server ADS Embedded Server Manager o te System information System Monitoring Configuration User Management Remote Control Maintenance User Account ADS Configuration Certificate Upad Gees a ONS Seting rnay ms I Domain Seting Tod conan Secondary NS IL ADS Configuration requires a Domain Name Server DNS an Active Directory Server ADS a Certificate Au thority Server CAS and an AD certificate 1 In the ADS Configuration page enter the file path of the CA certificate or browse to the location 2 Click Upload to upload the Certificate exported from the AD server 3 Enter Primary D
22. to protect the data 32 Bit Data Transfer enables and disables 32 bit data transfer Enable this only if your IDE documentation says that the device supports 32 bit data transfer 24 Chapter 3 BIOS Third IDE Slave Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Advanced Third IDE Slave Disabled Disables LBA Mode Auto Enables LBA Device 3 Not Detected Mode if the device supports it and the device is not already LBA Large Mode Auto Formatted with LBA Block Multi Sector Transfer Auto Mode disabled PIO Mode Auto DMA Mode Auto S M A R T Auto 32Bit Data Transfer Disabled lt Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Device displays the type of device assigned to this channel LBA Large Mode enables LBA access mode e Disabled LBA access mode is disabled e Auto LBA is set to optimal or default mode if the device supports it and is not formatted with LBA mode disabled Block Multi Sector Transfer enables multi sector transfer block mode e Disabled data transfer from and to the device occurs one sector at a time e Auto data transfer from and to the device occurs multiple sectors at a time if supported by the device PIO Mode select the device PIO Programmed Input Output mode which determines the data transfer mode
23. used by IDE drives PIO mode uses the CPU s registers for data transfer e Auto automatically detects optimal or default PIO mode e 0 4 select PIO mode 0 to 4 DMA Mode select the devices DMA Direct Memory Access mode which transfers data from channel to channel without using the CPU resulting in faster data transfer then when the CPU is used for every byte of transfer e Auto automatically detects optimal or default DMA mode e SWDMAO0 SWDMAz2 select SingleWord DMA 0 to 2 e MWDMAO MWDMA22 select MultiWord DMA 0 to 2 e UDMA 0 UDMAS select Ultra DMA 0 to 5 S M A R T Self Monitoring Analysis and Reporting Technology reports drive degradation to the operating system to warn you of potential failure e Auto automatically sets optimal or default S M A R T mode 25 Chapter 3 BIOS e Disabled disables S M A R T e Enabled enables S M A R T 32Bit Data Transfer enables 32 bit data transfer for improved performance 26 Chapter 3 BIOS Super IO Configuration Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Allows BIOS to Select Configure Nat42x Super IO Chipset Serial Port1 Base Addresses Serial Port1 Address 3F8 IRQ4 Serial Port2 Address 2F8 IRQ3 lt Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Super I O Configuration enabl
24. view the following web page Embedded Server Manager System information System Monitoring Config Network E mailNatfiraon PlaformEveniFilr Clock Settings System Management Access User Management Remote Control Maintenance Clock Setinas O NTP Server iP gHr cassblar User Seting 2 Manually enter the year month day and time hours minutes seconds 3 Click Submit to save the changes 63 Chapter 4 Using the Web UI System Management Access The System Management Access page enables the Administrator to generate SSL certificates and configure SNMP SSL Certificate The SSL Certificate page enables the Administrator to generate a new CSR Certificate Signing Request key automatically or upload the key Click the SSL Certificate tab to view the following web page Embedded Server Manager O e System Information System Monitoring Configuration User Management Remote Control Maintenance Network E mail Notiieation Platform Event Filler Clack Settings System Management Access SSL Cerificate SNMP GR see prm Tue cts keto end edo e Conon NenerCi I oranan fd pn S carey cot F Em E 3 Ses L Generating a CSR Before you can create the SSL Certificate you must first generate a CSR Certificate Signing Request on your server A CSR is a body of text that contains enc
25. 00 5300 5400 and Seaburg1600 Northbridge ESB2 E Southbridge chipsets Eight FBDIMM DDR2 533 667 800 slots enable you to add memory up to 32 GB ECC support provides extra security against system failure The two available SKUs support eight Serial Attached SCSI SAS ports up to six 3 0 Gb s SATA ports providing maximum flexibility for installing hard drives The QME 2200 has a full range of I O ports including two USB ports two Gigabit Ethernet LAN ports from ESB2 E one 10 100M LAN port from AST2000 one PS2 mouse port one PS2 keyboard port one 9 pin serial port and one 15 pin VGA port IPMB Intelligent Platform Management Bus headers provide administrator access in case of server board fail ure The IPMB connects externally through the ICMB Intelligent Chassis Management Bus The ICMB is used to connect the QME 2200 to the outside world providing data such as temperature voltage or chassis intrusion to the system administrator ASPEED 2000 server management firmware enables the administrator to monitor the QME 2200 status through a typical web browser Checklist The QME 2200 server board package ships with the following components Serverboard One IDE ribbon cable Ultra DMA 100 One installation manual included in the software drivers CD Serial ATA cable 2 I O shield If some items are missing or appear damaged contact your vendor immediately Features Processors Intel Xeon LGA771 CPU Seaburg1600 North Bridge
26. 5 general device initialization on the BUS concerned 6 func 6 error reporting for the BUS concerned 7 func 7 add on ROM initialization for all BUSes 8 func 8 BBS ROM initialization for all BUSes The lower nibble Y indicates the BUS on which the different routines are being executed Y can be from 0 to 5 0 Generic DIM Device Initialization Manager 1 On board System devices 2 ISA devices 3 EISA devices 4 ISA PnP devices 5 PCI devices 47 Chapter 3 BIOS APM Runtime Checkpoints APM checkpoints are displayed when an APM capable operating system either enters or leaves a sleep state The following table describes the type of checkpoints that may occur during APM sleep or wake events AC First ASL check point Indicates the system is running in PIC mode AA System is running in APIC mode 01 02 03 04 05 Entering sleep state S1 S2 S3 S4 or S5 10 20 30 40 50 Waking from sleep state S1 S2 S3 S4 or S5 Beep Codes The following table describes the beep codes that are used by AMIBIOS Number of Beeps Description Memory refresh timer error Parity error Main memory read write test error Motherboard timer not operational Processor error Keyboard controller BAT test error General exception error Display memory error ROM checksum error 2 2lvoj o ojo 5 o w 2 0 CMOS shutdown register read write error
27. 8 BMC Firmware Version 00 00 23 lt Select Screen Select Item Processor Change Option Intel R Xeon R CPU X5482 3 20 GHz Tab Select Field Speed 3200 MHz F1 General Help Count 2 F10 Save and Exit ESC Exit System Memory Size 512 MB System Time 17 40 55 System Date Mon 01 21 2008 V02 61 Copyright 1985 2006 American Megatrends Inc AMIBIOS Version displays the BIOS version Check this version number when updating BIOS from the manufacturer Build Date displays the date the BIOS was created Product Name displays the product name Product Board ID displays the SKU type Board Serial Number displays the mainboard serial number Processor Type displays the type of CPU installed on the mainboard Speed displays the maximum speed of the CPU Counter displays the number of installed processors System Memory Size displays how much memory DRAM is installed on the mainboard System Time scroll to this item to adjust the time System Date scroll to this item to adjust the date 18 Advanced Menu Chapter 3 BIOS This option displays a table of items that define advanced information about your system WARNING Making incorrect settings to items on these pages may cause the system to mal A function Unless you have experience adjusting these items we recommend that you leave these settings at the default values If making settings to items on these pages causes your system to malfuncti
28. B Slo Select Screen T3 Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc 33 Chapter 3 BIOS Server Menu This page enables you to configure Server parameters Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Main Advanced Boot Server Security Exit Enable or Disable Server Configuration ECC Event Logging Status of BMC Working IPMI Specification Version 2 0 BMC Firmware Version 00 00 23 NIC1 MAC Address 00 1B 24 BD F8 31 NIC2 MAC Address 00 1C 34 DF F9 56 gt Set AST2000 LAN Configuration gt Remote Access Configuration Restore on AC Power Loss Last State lt Select Screen Event Control Interface Select Item cl Enter Go to Sub Screen View BMC System Event Log F1 General Help Clear BMC System Event Log F10 Save and Exit ESC Exit BIOS Event Logging Enabled ECC Event Logging Enabled PCI Error Logging Enabled NB FSB Error Logging Enabled NB Internal Error Logging Enabled NMI on Error Fatal V02 61 Copyright 1985 2006 American Megatrends Inc 34 Chapter 3 BIOS Set AST2000 LAN Configuration These pages enable you to configure AST2000 LAN parameters Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY LETS EDIT IE IST M Server 1 1 s S Enter for IP Address LAN Configuration C
29. Copyright 1985 2006 American Megatrends Inc 30 Chapter 3 BIOS Boot Menu This page enables you to configure power management Scroll to this item and press Enter to view the follow ing screen BIOS SETUP UTILITY Main Advanced Server Security Exit Configure Settings Boot Settings during System Boot gt Boot Setting Configuration gt Boot Device Priority gt Hard Disk Drives gt Network Drives lt Select Screen td Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc 31 Chapter 3 BIOS Boot Settings Configuration Select this item and press Enter to view the following submenu items BIOS SETUP UTILITY Boot Settings Configuration certain tests while Allows BIOS to skip booting This will Quick Boot Enabled needed to boot the Quiet Boot Disabled system Addon ROM Display Mode Force BIOS Bootup Num Lock On Wait For F1 If Error Enabled Hit DEL Message Display Enabled Interrupt 19 Capture Enabled Select Screen nu Select Item decrease the time Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Select the priority and order of the devices that your system searches for an operating system at start up time Quick Boot If enabled default this item skips some
30. D Supported Modes The QME 2200 supports the following modes e Non Mirrored Mode e Single Channel Mode 14 Chapter 2 Installing Hardware Non Mirrored Mode Memory mirroring requires the corresponding slot positions in a channel pairs must hold the same DIMM type manufacturing speed timing organization and density See the example that follows Memory mirroring effec ively reduces available memory by half Non Mirrored Configuration Number of DIMMs 2 Slot 0 CH 0 BR 0 Slot 0 CH 1 BR 0 4 Slot 0 CH 0 BR 0 Slot 0 CH 1 BR 0 Slot 0 CH 2 BR 1 Slot 0 CH 3 BR 1 6 Slot 0 CH 0 BR 0 Slot 1 CH 0 BR 0 Slot 0 CH 1 BR 0 Slot 1 CH 1 BR 0 Slot 0 CH 2 BR 1 Slot 0 CH 3 BR 1 8 Slot 0 CH 0 BR 0 Slot 1 CH 0 BR 0 Slot 0 CH 1 BR 0 Slot 1 CH 1 BR 0 Slot 0 CH 2 BR 1 Slot 1 CH 2 BR 1 Slot 0 CH 3 BR 1 Slot 1 CH 3 BR 1 Note CH designates channel BR designates branch In non mirrored mode the memory upgrade granularity for each pair of locked step channels is two identical DIMMS one pair of corresponding slots on a selected branch Single Channel Mode Populate DIMM slots in the following order Branch 0 CH 0 Slot 0 Branch 0 CH 1 Slot 0 Note dw All channels must hold the same DIMM type as defined in the previous instructions Any subsequent memory upgrades should follow the rules listed above for Non
31. Ds and status will change synchronously ws 02 3 og 1024x768 0 Gbps TI Chapter 5 Using the Client Hot Key Simulation Since Windows or other application programs have priority in using hot keys before the remote server for exam ple Ctrl Alt Del the Java remote KVM ignores these keys and does not send them However you can assign hotkeys in the Java remote KVM application see Hotkey Setup on page 72 and these hotkeys are available on the menu bar where user can select hot keys to send to AST2000 and the managed server directly instead of pressing keys You can also set up hotkeys by clicking Control Setup HotKeys Hottest psf tian sf mem e j HotKey c ze Hoo mtm tie c Bottef0 c sit tie s Hotkey 3 sem erm s Bottes ju sux n a Hotte mtm tee m Bote o sius LI sedan mise el Botey 13 cu sft Hoteyit O sim gie m Hotkey cw sit silt ce sf Hotkeyte ca sft m sf sess rese Fil omw NOME 00m Mm csi The following screen displays the hot key menu Quality HotKey Storage gt ct AlttEnter amp MOM ae So co Alu FA c AlttSpace co AltsSysreq cof Alt Tab of CthEs c Ctrl Tab LF Ctrl Alt Delete c CthAlttEs of Chit AI FI c Chit AlHF2 cop Ctrl Alt F3 of Chit alts op Ctrl AlteES c Ctib lt F6 78
32. Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc Save Changes and Exit Highlight this item and press Enter to save any changes that you have made in the Setup utility and exit the Setup utility When the Save Settings and Exit dialog box appears press Y to save the changes and exit or press N to return to the setup main menu Discard Changes and Exit Highlight this item and press Enter to discard any changes that you have made in the Setup utility and exit the Setup utility When the Exit Without Saving dialog box appears press Y to discard changes and exit or press N to return to the setup main menu Discard Changes select this item and press lt Enter gt to discard any changes you have made without leaving the setup utility Load Optimal Defaults if you highlight this item and press Enter a dialog box asks if you want to install opti mal settings for all the items in the Setup utility Press the Y key to indicate Yes and then press Enter to install the optimal settings The optimal settings default values are quite demanding and your system might not function properly if you are using slower memory chips or other kinds of low performance components Load Failsafe Defaults If you highlight this item and press Enter a dialog box asks if you want to install fail safe settings for all the items in the Setup utility Press the Y key to indicate Yes and then press Enter to install the fail safe settings
33. Hetkey Setup Power Control Selact Action v SAVE e In the Power Control frame select Power Off On from the drop down menu then click Save to turn off on the remote server OR e Select Reset and then click Save to reset the remote server Hotkey Setup This page enables the administrator to create user profiles that include control modes KVM settings hot key set tings and storage settings These settings are loaded after the Java Remote KVM is launched Click the Hotkey Setup tab to view the following web page Embedded Server Manager System Information System Monitoring Configuration User Management Remote Control Maintenance Redirection Remote Power Qunirel Hotkey Setup User Prete username root Control Mode Video Quaity Low ku Seti ee Encryption mode No Encryption S HotKey Setting E ae Wj Ene HotKey Setting 2 E M_E Ese at key Setting 3 E se F E ot ey Setting 4 a p E race Username Displays the name of the user for this profile e Control Mode Select a view mode from the drop down list and check the boxes that you wish applied to this profile e KVM Setting Select the video quality and the encryption mode for this profile e Hot Key Setting 1 16 Select the Hot Key settings from the drop down lists 72 Chapter 4 Using the Web UI Maintenance The Mai
34. I ACPI compliance S0 S1 S4 S5 support Board Main Logic Board Sensors Management System voltage detection Control BMC System Temperature Detection Adaptive FAN Speed Control FAN Speed Detection Hardware monitor CPU Temperature Detection CPU VID code BMC AST 2000 Form factor 2U system Full size ATX 12 inch x 13 inch BIOS AMI Server BIOS Appendix B Specifications SKU Information Component Hybrid SATA Hybrid SAS SKU ID CPU Dempsey Dempsey Woodcrest Woodcrest Wolfdale DP Wolfdale DP Clovertown Clovertown Harpertown Harpertown MCH Seaburg Seaburg SB ESB2 E ESB2 E Memory 8 DDR2 RDIMMs on 4 channels 8 DDR2 RDIMMs on 4 channels 32 GB MAX 32 GB MAX SIO Nat42x Nat42x IO 5 slots 5 slots 1 PCI X 64 100 1 PCI X 64 100 1 PCI X 64 133 1 PCI X 64 133 1 PCI E x 4 1 PCI E x 4 1 PCI E x 4 ROMB CARD 1 PCI E x 4 ROMB CARD 1 PCI E x 16 1 PCI E x 16 Storage SATA STATII 6 ports via ESB2 E 8 SAS ports SAS MB SAS controller depop LSI 1068E SAS controller Video AST2000 AST2000 Note The following CPU types are supported Dual Core Intel Xeon processor 5000 series Dempsey Dual Core Intel Xeon processor 5100 series Woodcrest Dual Core Intel Xeon processor 5200 series Wolfdale DP Quad Core Intel Xeon processor 5300 series Clovertown Quad Core Intel Xeon processor 5400 series Harpertown 89
35. Line Prefetch Enabled Select Item Max CPUID Value Limit Disabled EN Eid id ee eneral He Intel R Virtualization Tech Enabled F10 Save and ES Execute Disable Bit Capability Enabled ESC Exit PECI Enabled Core Multi Processing Enabled Intel R Speedstep tm tech Enabled V02 61 Copyright 1985 2006 American Megatrends Inc Manufacturer displays the CPU manufacturer Frequency shows the rated processing speed of the CPU FSB Speed displays the data transfer speed of the front side bus CPU 1 CPU2 CPUID displays the CPU ID Cache L1 speed rating of the internal L1 cache Cache L2 speed rating of the external L2 cache Ratio status displays the running ratio of the CPU for higher FSB turning Always Locked Ratio Active Value core frequency to the FSB multiplier Always Maximum 20 ACPI Configuration Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Chapter 3 BIOS Advanced ACPI Configuration ACPI Version Features ACPI v2 0 Enable RSDP pointers to 64 bit Fixed System Description Tables Different ACPI version has some additions lt Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc 21 Chapter 3 BIOS IDE Configuration Scroll to this item and press Enter to view the following screen BIOS SETUP
36. MM 1 DIMM 2 DIMM 3 DIMM 4 Description Nerrory Information Memory Module a Status ok Socket mm Module Size 44032MB Type soran Frequency E ToP Description Memory Information Memory Module Status ok Suey sn 56 Chapter 4 Using the Web UI System Monitoring The System Monitoring tab enables the administrator to view data about the system including LED system fan temperature and voltage status and event logs You can also enable server LED blinking on the Locator Indicator page to identify a particular server Click the System Monitoring tab to view the following web page Embedded Server Manager System mrormation Montong Configuration User Management Remote contol Malmenanco SensorResdng EvertLoge Lotatorinciestor FautieD Summe theestewtusn Fan Temperature volage Fault LED Status Power Status On Fan Statue Temparaluro Status cpu2 temp Dissbled Sensor Reading The Sensor Reading tab provides information about system hardware such as the fan s and voltage Summary Click the Summary tab to display a brief overview of system hardware status Embedded Server Manager peed internal temperature System formation System Mentoring Configuration User Management Remote Control Maintenance SensorReading Eveniogs Locatorindesor Faut LEO Summary Chassisirusion Fan Temperature Voltage
37. Management Remote Control Maintenance Versions Session Time Out Components BMC Version Sewer Board lniorration B DIAC Version Decore BMC Version Device D 5 Deuce Revision o Frmware Revision ov FM Revision 20 10 Version Click the BMC version tab to view BMC information including the device ID Device Revision Firmware Revi sion and IPMI Revision numbers 53 Chapter 4 Using the Web UI Embedded Server Manager o OO m m Systeminformation System Monitoring Configuration User Management Remote Control Maintenance Versions SessionTimeOut Components BMC Verein Sowar Board Information Menu DIAC Version Desertion BMC Vercion Device D 5 Deuce Revision o Femyave Revision ov FM Reisen 22 54 ix 2 Chapter 4 Using the Web UI Click the Server Board version tab to view Server Board information including manufacturer date product name P N and S N Embedded Server Manager System Information Systm Monitoring Configuration Usor Management Remote Control Maintenance Versione SessionTimo Out Components BMC Version Server Board Informaton Server Board Information ToP Desertore Server Board information pum we 200 HI AOL 0000 parer won 231841471979 pum Ter ate m camo j Set be p Pert Number S15N9BO000
38. NICIANS ARE AUTHORIZED TO REMOVE THE COVERS AND ACCESS ANY OF THE COMPONENTS INSIDE THE SYSTEM t3 Power Supply Cord CAUTION THIS SYSTEM MAY HAVE MORE THAN ONE POWER SUPPLY CABLE TO REDUCE THE RISK OF ELECTRICAL SHOCK A TRAINED SERVICE TECHNICIAN MAY NEED TO DISCONNECT ALL POWER SUPPLY CABLES BEFORE SERVICING THE SYSTEM Ambient Operation This equipment cannot be operated above an ambient operation temperature of 40 degrees centigrade Typographic Conventions Several different typographic conventions are used throughout this manual Refer to the following examples for common usage Bold type face denotes menu items buttons and application names Italic type face denotes references to other sections Note Highlights general or useful information and tips CAUTION CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES SIMILAR TO NOTES AND WARNINGS CAUTIONS HOWEVER APPEAR IN CAPITAL LET WARNING Warning information appears before the text it references and should not be ig nored as the content may prevent damage to the device TERS AND CONTAIN VITAL HEALTH AND SAFETY INFORMATION TABLE OF CONTENTS CHAPTER 1 1 Introduction 1 Checklist 1 Features 1 Serverboard Components 2 SATA SKU 2 SAS SKU 3 Input Output Ports 4 Block Diagram 5 CHAPTER 2 7 Installing Hardware 7 Safety Measures 7 Serverboard Jumper Settings 8 Setting a Jumper 8 Jumper Locations and Functions 9 Installing the CPUs 10 Installing th
39. NS Domain Name Server IP and root domain AD server Domain In the Clock Settings page ensure BMC shows the same time as the AD Server Click Submit Log off and log in to the Web GUI with the username and password you set in AD server BO p 68 Chapter 4 Using the Web UI Remote Control By using the included Java client users have access to robust remote control features Note Refer to the next chapter for more information on remote control features Ensure that you have the java runtime machine JVM version 1 5 or higher installed before using the remote control Click the Remote Control tab to view the following web page Embedded Server Manager System information System Monitoring Configuration User Management Maintenance Launch Redirection Manage the hast server remotely by redirecting the system console to your local machine ME Redirection Launch Redirection enables you to control the server through your local PC Follow these instructions to use Launch Redirection 1 Click the Redirect tab 2 Click the Launch Redirection button Embedded Server Manager User Management Configuration System information System Monitoring Launch Redirection Manage the hast server remotely by redirecting the system console to your local machine Launch Redirection The following warning screen appears Embedded Server Manager System
40. POST routines to speed up boot time Quiet Boot If disabled default the results of the POST are displayed enabled causes a logo screen to appear instead AddOn ROM Display Mode Display mode controlled by BIOS or addon ROM Boot Up Num lock If on default the Num Lock key is activated at start up Wait For F1 If Error Wait for the user to press the F1 key if an error occurs during POST Default is Enabled Hit DEL Message Display Enable this item to have the system prompt you to press DEL to enter the BIOS Setup Utility Interrupt 19 Capture If enabled default the system allows ROM to trap interrupt 19 events 32 Chapter 3 BIOS Boot device Priority Press lt Enter gt and select the order in which the various bootable devices load The system will prioritize the de vices it looks for during boot up BIOS SETUP UTILITY Specifies the boot Boot Device Priority sequence from the available devices 1st Boot Device HDD 3M ST320410A A device enclosed in 2nd Boot Device Network IBA GB Slo parenthesis has been disabled in the corresponding type menu Select Screen T Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyri 6 American Megatrends Inc Network Drives BIOS SETUP UTILITY Specifies the boot Network Drives sequence from the available devices 1st Drive Network IBA GE Slo 2nd Drive Network IBA G
41. UTILITY IDE Configuration Options Disabled ATA IDE Configuration Enhanced Compatible Configure SATA as IDE Enhanced gt Primary IDE Master Not Detected gt Primary IDE Slave Not Detected gt Secondary IDE Master Not Detected gt Secondary IDE Slave Not Detected gt Third IDE Master Hard Disk gt Third IDE Slave Not Detected lt Select Screen Hard Disk Write Protect Disabled t Select Item IDE Detect Time Out Sec 35 Change Option ATA PI 80 Pin Cable Detection Host amp Device F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc IDE Configuration enables you to configure IDE devices such as hard disk or CD ROM drives dw Note Primary Secondary IDE Master Slave There are two IDE channels Primary and Secondary and each channel can be installed with one or two devices Master and Slave Use these items to configure each device on the IDE channel e Hard Disk Write Protect when enabled writes to the HDD are not permitted e IDE Detect Time Out Sec maximum time spent auto detecting connected IDE peripherals Select Primary Secondary or Third to configure each device on the IDE channel The following example shows Third IDE channel configuration 22 Chapter 3 BIOS Third IDE Master Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Advanced Third IDE Master Disa
42. VIDIA Network Bus Enumerator 9 Ports COM amp LPT Processors i Sound video and game controllers system devices amp amp Universal Serial Bus controllers USB Floppy Emulation When Floppy Emulation function is enabled the managed server will find a USB floppy drive As shown in the image below the user puts a target diskette into the remote console PC floppy drive While managed server will access this virtual attached USB floppy diskette AST2000 will redirect to the diskette in console PC and Java Remote KVM will access the target diskette instead The diskette access includes In Solaris Linux use xset m 1 1 at the command line Read Write Format Media Changed ejects then inserted diskette Device Manager File Action View Help gt e628 Ba STATIONS ig Computer p Disk drives 3 Display adapters T DVD CD ROM drives 5 5 Floppy disk controllers Edi Floppy disk drives amp dy Human Interface Devices E IDE ATAJATAPI controllers x9 Keyboards m 3 Mice and other pointing devices x fd Monitors 5B Network adapters NVIDIA Network Bus Enumerator Ports COM amp LPT H Processors Sound video and game controllers 19 System devices amp amp Universal Serial Bus controllers 83 Chapter 5 Using the Client The below table describes the floppy LED status description Legacy Floppy As d
43. an external monitor 7 Serial Port Use the serial port COM1 to connect serial devices such as mice or fax modems 8 KVM over IP Connect a RJ 45 jack to this port to link to a 10 100M LAN from AST2000 9 NIC1 Port 10 100 1000 Mbps RJ 45 LAN port for onboard LAN chipset 10 NIC2 Port 10 100 1000 Mbps RJ 45 LAN port for onboard LAN chipset I O Port Color Coding The industry has adopted a standard color code to identify many of the I O ports used in today s systems Connector Color Analog VGA Blue PS 2 compatible keyboard Purple PS 2 compatible mouse Green Serial Teal or Turquoise USB Black LAN Black Chapter 1 Introduction Block Diagram Slot 6 Dual Core Intel Xeon processor 5100 series Quad Core Intel Xeon processor 5300 series Harpertown Wolfdale DP processors FSB 16500MHz FSB 1600MHz FBD DDR2 ECC DIMM PCIE x16 ep Lan PCLE x16 Intel FBD 800Mhz ira GB LAN2 ATA 100 AST2000 DATA PCI 32 33 Intel ESB2 E PCI E x4 PCLE x4 PCLE x4 PCI E x8 slot PCI X 64 133 This concludes the first chapter The next chapter explains how to install components Chapter 1 Introduction Notes Chapter 2 Installing Hardware Chapter 2 Installing Hardware Safety Measures Computer components and electronic circuit boards can be damaged by discharges of static electricity Working on computers that are still connected to a pow
44. and 3 for the location of the memory mod ules Refer to the following instructions to install memory modules 1 Pull the locking latches of the DIMM slot outwards 2 Align the memory module correctly Note the notch and obstruction in the following illustration Locking latch Memory module Locking latch Obstruction 3 Press the edge connector of the memory module into the slot Press down firmly so that the locking latches of the DIMM slot are levered upwards to secure the memory module in place 13 Chapter 2 Installing Hardware Supported DIMM Configuration The following DIMM configurations are supported by the QME 2200 server board DIMM slots are numbered 0 to 1 and designated by two branches each containing two channels Populate DIMM slots starting with slot 0 channel 0 branch 0 DIMM A1 See the following for possible memory configurations Branch 0 Branch 1 Channel O Channel 1 Channel 2 Channel 3 DIMM 1A DIMM 1D DIMM_2A i SS EEE DIMM 2D Slot 1 Slot 0 RONDE OEODU OD ODOG DOG OCDE CON RON EON T DIMM 28 DIMM 2C DIMM 1B DIMM 1C Branch Channel Slot Branch 0 Channel 0 Slot 1 DIMM 2A Slot 0 DIMM 1A Channel 1 Slot 1 DIMM 2B Slot 0 DIMM 1B Branch 1 Channel 2 Slot 0 DIMM 1C Slot 1 DIMM 2C Channel 3 Slot 0 DIMM 1D Slot 1 DIMM 2
45. and software is protected under international copyright laws with all rights reserved Neither this manual nor any of the material contained herein may be reproduced without the express written consent of the manufacturer Version 1 0 April 2008 Disclaimer The information in this document is subject to change without notice The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose Furthermore the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes iv Safety Information READ THIS IMPORTANT SAFETY INFORMATION SECTION RETAIN THIS MANUAL FOR REFERENCE READ THIS SECTION BEFORE SERVICING CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK THIS SERVER BOARD SHOULD ONLY BE SERVICED BY QUALIFIED SERVICE PERSONNEL t3 RTC Battery CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DIS CARD USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS t3 Power Supply CAUTION THE POWER SUPPLIES IN YOUR SYSTEM MAY PRODUCE HIGH VOLTAGES AND ENERGY HAZARDS WHICH CAN CAUSE BODILY HARM UNLESS YOU ARE IN STRUCTED OTHERWISE ONLY TRAINED SERVICE TECH
46. ate the event occurred e Description describes the event in more detail 59 Chapter 4 Using the Web UI Save Event Logs l Click the Save Event Logs tab to view the following screen Embedded Server Manager o te Systeminformation System Monitoring Configuration User Management Remote Control Maintenance SensorReeding EventLogs Locatorindicator Fault LED View EventLogs Seve Evert Logs Clear Evert Logs Save Evert Log 2 Click Save Event Logs to save the log to disk You are prompted to save the event log text file to disk File Download Do you want to open or save this file While files from the Intemet can be useful some files can potentially ham your computer If you do not trust the source do not open or save this file What s the risk 3 Click Save to save the log file to your hard drive Clear Event Logs 1 Click the Clear Event Logs tab to view the following screen Embedded Server Manager System Information Systom Monitoring Configuration User Managomont Remote Control Mainfonanco Sensor Reading EventLogs Locatorincicator Fault LED ViewEventLogs Save EventLegs ClearEvent Logs 2 Click Clear Event Log to clear the current log The following screen displays when the logs have been cleared Clear Event Log Clear Event Log Succeeded 60 Chapter 4 Using the Web UI Locator Indi
47. ava Remote KVM The Java Remote KVM interface has several buttons that provide different functionality e Video Quality Enables you to select the video quality low medium or high High Fewest video loss and biggest size image transmitted Normal Few video loss and big size image transmitted Low Some video loss and small size image transmitted Hot Key Displays hot key function Refer to Hotkey Setup on page 72 Storage Enables you to mount a virtual storage device Scale Fit Reduces magnification of the current screen until it fits in the window Scroll Mode Zoom is disabled use scroll bar to view screen Full Screen Get the current KVM screen to zoom into the client monitor Local Cursor Enable and disable the client cursor in KVM Hardware Cursor Enable and disable the hardware cursor Hardware provides the cursor position and cursor shape to draw the cursor in the client KVM Note d For more information on using the Java remote KVM refer to the next chapter 71 Chapter 4 Using the Web UI Remote Power Control This feature enables the administrator to power on or power down the system remotely Note dw The IPMI connector must be connected to enable this function Click the Remote Power Control tab to view the following web page Embedded Server Manager O tele System Information SystomMonioring Configuration Usor Management Romote Control Maintenance Redirection Remote Power Cortrol
48. bled Disables LBA Mode Auto Enables LBA i Mode if the device Device Hard Disk supports it and the Vendor ST320410A device is not already Size 20 0 GB Formatted with LBA LBA Mode Supported Mode disabled Block Mode 16Sectors PIO Mode i 4 Async Mode MultiWord DMA2 Ultra DMA i Ultra DMA2 S M A R T Supported lt r pe Auto lt Select Screen yi u LBA Large Mode Auto sid iet Block Multi Sector Transfer Auto ange pron F1 General Help PIO Moda Auto F10 Save and Exit DMA Mode Auto S M AR T Auto ESC Exit 32Bit Data Transfer Enabled V02 61 Copyright 1985 2006 American Megatrends Inc Third IDE Master displays information about the hard disk that is installed as a primary IDE device on the sys tem The following information is displayed e Device type of IDE device installed e Vendor manufacturer of IDE device e Size capacity of IDE device e LBA Mode displays whether LBA mode is supported or not set below e Block Mode displays the number of sectors in a block set below e PIO Mode displays the PIO mode setting set below e Async Mode displays the asynchronous mode settings for the DMA channel e Ultra DMA displays the Ultra DMA mode setting set below e S M A R T displays whether S M A R T mode is supported or not set below LBA Large Mode enables you to set the Logical Block Addressing mode Select Auto to let BIOS automatically detect the LBA mode LBA mode is used t
49. boot the machine This message appears after a fatal error has been detected This concludes the BIOS chapter The following chapter explains Using the Web UI Chapter 4 Using the Web UI The AST2000 firmware features an embedded web server enabling users to connect to the AST2000 using an Internet browser Microsoft Internet Explorer without needing to install KVM and Virtual Storage software on the remote console side PC The following web browsers are supported e Internet Explorer 6 and 7 e Mozilla 1 7 13 or later e Firefox 1 5 or later Note dv If BMC F W recovery is required short jumpers J1C2 and J2A1 enabling the MB to boot directly Setting the KVM TCP Port on Network The AST2000 web user interface requires access to the system s TCP ports Before using the web user interface ensure that the firewall settings are configured to allow access to the following ports 8890 KVM 9000 Stor age 9001 9002 and 9003 Note dw For information on configuring firewall settings to allow TCP port access refer to your firewall software user s guide Logging into the Web User Interface Users must enter the AST2000 embedded server IP address or URL into the address bar of the web browser or connect using OEM customer s Embedded Server Management ESM The default IP address is https 192 168 1 87 When connecting to the AST2000 using a web browser SSL is automatically activated and the display user login f
50. cator l Click the Locator Indicator tab to view the following screen Embedded Server Manager System Information System Monitoring Coniguration User Management Remote Control Maintenance SensorReading Event Logs Locaturindicstor Fauli LED SYSTEMINDCATORLED Current Status off O run system inatcstor LED on Turn system indicator LED off Or system necator LED bint klik time interval 15_ seconds 1 285 Lsubmk Reset 2 Click on the desired setting e Turn system indicator LED on set the system indicator LED on the remote server to blink e Turn system indicator LED off set the system indicator LED on the remote server to off e System Indicator LED blink set the blinking interval on the system indicator LED Fault LED 1 Click the Fault LED tab to view the following screen Embedded Server Manager System Information figuran User Manayornont Remoto Control Maintenance SensarReading EvertLogs Locatorindicator FaultLED Faut LED Control Current Statue Off 2 Click on the desired setting e Turn fault LED on set the fault LED on the server to blink e Turn fault LED off set the fault LED on the server to off 61 Chapter 4 Using the Web UI Configuration The Configuration tab enables you to set network parameters e mail notification Platform Event Filter load and enable an SSL certificate and to set Time options Embedded Server Manager o
51. checkpoints that may occur during the POST portion of the BIOS Checkpoint Description 03 Disable NMI Parity video for EGA and DMA controllers Initialize BIOS POST Run time data area Also initialize BIOS modules on POST entry and GPNV area Initialized CMOS as men tioned in the Kernel Variable wCMOSFlags 04 Check CMOS diagnostic byte to determine if battery power is OK and CMOS checksum is OK Verify CMOS checksum manually by reading storage area If the CMOS checksum is bad update CMOS with power on default values and clear passwords Initialize status register A Initializes data variables that are based on CMOS setup questions Initializes both the 8259 com patible PICs in the system 05 Initializes the interrupt controlling hardware generally PIC and interrupt vector table 06 Do R W test to CH 2 count reg Initialize CH 0 as system timer Install the POSTINT1Ch handler Enable IRQ 0 in PIC for system timer interrupt Traps INT1Ch vector to POSTINT1ChHandlerBlock 08 Initializes the CPU The BAT test is being done on KBC Program the keyboard controller com mand byte is being done after Auto detection of KB MS using AMI KB 5 co Early CPU Init Start Disable Cache Init Local APIC C1 Set up boot strap processor Information C2 Set up boot strap processor for POST C5 Enumerate and set up application processors C6 Re enable cache for boot strap pr
52. d the BMC firmware release notes to determine which update utility version is appropriate for the new firmware version i Copy the BMC firmware update utility upfw exe and BMC firmware image file S87vxxx bin to a boot able DOS diskette Where xxx means BMC firmware version Shutdown the server and insert this diskette then power on the server and boot to the diskette At the DOS prompt e g A gt type upfw S87vxxx BIN not case sensitive and press the ENTER key upfw exe displays a message during the flash in progress Wait for the flash to complete and make sure no error or failure message appears Power off the server and remove the diskette then power on 87 Appendix B Specifications Component Feature CPU Dual Processor for Intel Xeon DP 1066 1333 1600 MHz bus Supports Intel Dempsey Woodcrest Clovertown Also supports Harpertown Wolfdale VRD11 Chipset Northbridge Intel Seaburg1600 e 1066 1333 1600 MHz FSB e ESI interface 2 5GB s e 8XFBD DDR2 DIMMs Southbridge ESB2 E e ESI interface 2 5GB s to SB e Ultra 100 IDE e SATAIIx 6 e USB20x4 Kumeran interface to external Gigabit Ethernet PHY Memory 2 DIMM per channel total 4 channels Supports up to 32 GB Supports FBD 533 667 800 DDR2 USB Rear panel x 2 Front panel x 2 VGA Onboard VGA AST2000 LAN Onboard Gigabyte Ethernet x 2 Intel 82563EB SUPER I O PS 2 Keyboard Mouse Serial port NS87427 ROM FWH 8M bit ACP
53. down register for CMOS RAM failed Read Write Error 11 Cache Error External Cache Bad The external cache is faulty Troubleshooting BIOS Beep Codes 1 20r3 Reseat the memory or replace with known good modules 4 7 9 11 Fatal error indicating a serious problem with the system Before replacing the motherboard eliminate the possibility of interference by a malfunc tioning add in card Remove all expansion cards If the beep codes are generated even when all other expansion cards are absent the motherboard has a serious problem If the beep codes are not generated when all other expansion cards are absent one of the add in cards is causing the malfunction Insert the cards back into the system one at a time until the problem happens again This procedure will reveal the malfunctioning add in card 8 If the system video adapter is an integrated part of the system board like S52D the board may be faulty Checkpoints and Beep Codes A checkpoint is either a byte or word value output to I O port 80h The BIOS outputs checkpoints throughout bootblock and Power On Self Test POST to indicate the task the system is currently executing Checkpoints are very useful in aiding software developers or technicians in debugging problems that occur during the pre boot process Beep codes are used by the BIOS to indicate a serious or fatal error to the end user Beep codes are used when an error occurs before the system vid
54. dows Server2003 ase oa LEE aAA Od 102460 24 Ons Num Caos 80 Chapter 5 Using the Client Encryption Mode Encryption includes the following modes 1l No encryption 2 Keyboard and mouse encryption Uses AES method for encryption 3 Video Only encryption Uses RC4 method for encryption 4 Encryption All Encrypts the Keyboard Mouse and Video The client side can only view encryption mode however users can access the web user interface to change the encryption mode and launch again Virtual Storage Through the USB storage emulation functions of the AST2000 users can install an operating system device driv ers or application software from the convenience of a remote side Mounting a Device This section describes how to set up virtual storage for the QME 2200 Follow these instructions to configure a storage device 1 Click Storage Mount Device Unmcunt Device PISOTmaEE Computer 81 Chapter 5 Using the Client The following screen appears Device Configuration xj pStorage 1 Media name Media type Mount point Submit Choose Available Device zl Cancel p Storage 2 Media name Media type Mount point Choose Available Device zl Storage D Media name Media type Mount point Choose Available Device z 2 Sel
55. e Heatsinks 12 Installing Memory 13 Supported DIMM Configuration 14 Supported Modes 14 Installing a PCI Card 16 CHAPTER 3 17 BIOS 17 Setup Menu 17 BIOS Setup Options at Boot 17 Main Menu 18 Advanced Menu 19 CPU Configuration 20 ACPI Configuration 21 IDE Configuration 22 Super IO Configuration 27 USB Configuration 28 PCI Configuration 29 MPS Configuration 30 Boot Menu 31 Boot Settings Configuration 32 Boot device Priority 33 Network Drives 33 Server Menu 34 Set AST2000 LAN Configuration 35 Remote Access Configuration 40 Security Menu 41 Exit Menu 42 BIOS Check Point and Beep Code List 43 Definition of Beep Codes 43 Troubleshooting BIOS Beep Codes 43 Checkpoints and Beep Codes 43 Bootblock Initialization Code Checkpoints 44 Bootblock Recovery Code Checkpoints 44 POST Code Checkpoints 45 DIM Code Checkpoints 47 APM Runtime Checkpoints 48 Beep Codes 48 Troubleshooting BIOS Beep Codes 48 Error Message Descriptions 49 Memory 49 Boot 49 Storage Device 50 Virus Related 50 System Configuration 51 CMOS 51 Miscellaneous 52 vi CHAPTER 4 Using the Web UI Setting the KVM TCP Port on Network Logging into the Web User Interface System Information Version Session Time Out Components System Monitoring Sensor Reading Event Logs Locator Indicator Fault LED Configuration Front Panel Lockout Network E mail Notification Platform Event Filter Clock Settings System Management Access User Management Changing the Administrative
56. ect the storage device or ISO image from the drop down list 3 When a storage device is mounted the status bar displays an icon 4 Ifyou select ISO Image you will be prompted to browse to the location of the ISO file ISO image format supports ISO9660 In addition ISO image emulates a DVD ROM on the managed server through AST2000 Mounted device 5 To change the ISO Image Click Storage Change ISO Image Supported Devices Device Action Legacy Floppy USB Floppy Read and Write Floppy support Media Change USB Flash Device Action USB CD DVD ROM IDE CD DVD ROM Read only support Media Change ISO Image 82 Chapter 5 Using the Client USB DVD Emulation When DVD Emulation function is enabled the managed server finds a USB DVD drive As shown in the image below the user puts a target DVD disk into the remote console PC DVD drive While managed server access this virtual attached USB DVD AST2000 will redirect to the DVD in console PC and Java Remote KVM will access the target DVD disk instead The DVD format will support DVD R and R according to your CD DVD ROM Device Manager File Action View Help meS RARA B STATIONS Computer lt Disk drives Display adapters B Floppy disk drives Bl Human Interface Devices IDE ATAJATAPI controllers xo Keyboards Mice and other pointing devices g Monitors 5H Network adapters N
57. een Active LED Blinking Green J7A1 10 100 LAN connector AST2000 Link LED Green Active LED Blinking Green J1B2 Intrusion connector Pin1 FP_CHASSIS_INTRU Pin2 GND J1K4 IPMB 5V connectors Pin1 SMB_IPMB_5V_DAT Pin2 GND Pin3 SMB_IPMB_5V_CLK Pin4 Pull down J1K1 IPMB 5V connectors Pin1 SMB_IPMB_5V_DAT Pin2 GND Pin3 SMB_IPMB_5V_CLK Pin4 Pull high J2H4 SGPIO header Pin1 SGPIO_CLOCK Pin2 SGPIO_LOAD Pin3 SGPIO_DATAOUTO Pin4 SGPIO_DATAOUT1 J2K1 IPMB 5VSTB connector Pin1 SMB_IPMB_5VSB_DAT Pin2 GND Pin3 SMB_IPMB_5VSB_CLK Pin4 P5V_STBY J1C1 Clear CMOS header 1 2 Normal operation default 2 3 COMS clear J1D1 Clear Password header 1 2 Password protect default 2 3 Password Clear 10 J9D1 IPMB connector for power supply reserve Pin1 3V3SB_PWR_CLK Pin2 3V3SB_PWR_DAT Pin3 SMB_ALERT Pin4 GND Pin5 P3V3 141 J1C2 BMC recovery Function Short J1C2 during BMC recovery function 12 J2A1 BMC recovery Function Short J2A1 during BMC recovery function Chapter 2 Installing Hardware Installing the CPUs WARNING In a single CPU configuration the single processor must be installed in the CPU 1 socket see Serverboard Components on page 2 for location Refer to the following instruct
58. en appears Embedded Server Manager System information System Monitoring Configuration User Management Remote Control Maintenance UserArcount ADS Configuration Ed Old Password Password Confirm Cant 2 Type the current password in the Old Password text box 3 Type the new password 4 Type the password again for confirmation 5 Click Submit to save the new password 66 Chapter 4 Using the Web UI Managing Users This section describes how to add a new user and set user privileges Adding a User l Click Add User The following screen appears Embedded Server Manager eee System Information System Monitoring Configuration User Management Remote Control Maintenance UserAccount ADS Configuration User List Ussmane Privilege Staus rect Acmiictrater Enabled Change Passwerd _ petaut Account cart delete m Aeminictreter Enabled Drabi C change Password L charge rige _ Delete Add User Adi User Ad User Adi User Ad User Add User Adi User 2 Type the Username in the text box 3 Type the Password in the text box and type it again for confirmation 4 Select the privilege to assign to this user e Administrator e Operator e User e Call Back 5 Click Submit to save the user Editing User Information After a User is added the administrator can change the user s
59. en to it BIOS now executes out of RAM D6 Both key sequence and OEM specific method is checked to determine if BIOS recovery is forced Main BIOS checksum is tested If BIOS recovery is necessary control flows to checkpoint EO See the Bootblock Recovery Code Checkpoints section of this documentation for more informa tion D7 Restore CPUID value in register The Bootblock Runtime interface module is moved to system memory and control is given to it Determines whether to execute serial flash D8 The Runtime module is uncompressed into memory CPUID information is stored in memory D9 Store the Uncompressed pointer for future use in PMM Copy Main BIOS into memory Leaves all RAM below 1MB Read Write including E000 and F000 shadow areas but closing SMRAM DA Restore CPUID value in register Give control to BIOS POST ExecutePOSTKernel See the POST Code Checkpoints section of this document for more information Bootblock Recovery Code Checkpoints The Bootblock recovery code gets control when the BIOS determines that a BIOS recovery needs to occur be cause the user has forced the update or the BIOS checksum is corrupt The following table describes the type of checkpoints that may occur during the Bootblock recovery portion of the BIOS Checkpoint Description EO Initialize the floppy controller in the super I O Some interrupt vectors are initialized DMA con troller is initialized
60. eo has been initialized Beep codes are generated by the system board speaker commonly referred to as the PC speaker 43 Chapter 3 BIOS Bootblock Initialization Code Checkpoints The Bootblock initialization code sets up the chipset memory and other components before system memory is available The following table describes the type of checkpoints that may occur during the bootblock initialization portion of the BIOS Checkpoint Description Before D1 Early chipset initialization is done Early super I O initialization is done including RTC and key board controller NMI is disabled DO Perform keyboard controller BAT test Confirm waking up from power management suspend state Save power on CPUID value in scratch CMOS Enable I O devices D1 Go to flat mode with 4GB limit and GA20 enabled Verify the bootblock checksum Initial CPU at power on D2 Disable CACHE before memory detection Execute full memory sizing module Verify that flat mode is enabled Verify the bootblock checksum D3 If the memory sizing module did not execute start memory refresh and do memory sizing in Bootblock code Do additional chipset initialization Re enable CACHE Verify that flat mode is enabled Disable cache prior to memory detection and then do memory sizing D4 Test base 512KB memory Adjust policies and cache first 8MB Set stack D5 Bootblock code is copied from ROM to lower system memory and control is giv
61. er supply can be extremely dangerous Follow the simple guidelines below to avoid damage to your computer or yourself e Always disconnect the computer from the power outlet whenever you are working inside the computer case e If possible wear a grounded wrist strap when you are working inside the computer case Alternatively discharge any static electricity by touching the bare metal chassis of the computer case or the bare metal body of any other grounded appliance e Hold electronic circuit boards by the edges only Do not touch the components on the board unless it is necessary to do so Do not flex or stress the circuit board e Leave all components inside the static proof packaging until you are ready to use the component for the installation Chapter 2 Installing Hardware Serverboard Jumper Settings Refer to this section when setting the jumpers on the server board Setting a Jumper The server board jumpers are to set system configuration options When setting jumpers ensure the shunts jumper caps are placed on the correct pins This 2 pin jumper is ON SHORT This 2 pin jumper is OFF OPEN Pins 1 and 2 are ON SHORT on this 3 pin jumper s Jumper Locations and Functions Refer to the following table for jumper names and functions Item 1 Name J5A1 J6A1 Function 10 100 1000 LAN connector Gilgal Chapter 2 Installing Hardware Setting Link LED 10 None 100 green 1G Orange Link Gr
62. error reporting standard S M A R T failure messages may indicate the need to replace the hard disk S M A R T Capable and Status BAD A S M A R T capable hard disk sends this message when it detects an imminent failure This message can be reported by an ATAPI device using the S M A R T error reporting standard S M A R T failure messages may indicate the need to replace the hard disk Virus Related Message Displayed Description Boot Sector Write The BIOS has detected software attempting to write to a drive s boot sector This is flagged as possible virus activity This message will only be displayed if Virus Detection is enabled in AMIBIOS setup If the BIOS detects possible virus activity it will prompt the user This mes sage will only be displayed if Virus Detection is enabled in AMIBIOS setup VIRUS Continue Y N 50 System Configuration Chapter 3 BIOS Message Displayed Description DMA 2 Error Error initializing secondary DMA controller This is a fatal error often indication a problem with system hardware DMA Controller Error POST error while trying to initialize the DMA controller This is a fatal error often indication a problem with system hardware Checking NVRAM Update Failed BIOS could not write to the NVRAM block This message appears when the FLASH part is write protected or if there is no FLASH part System uses a PROM or EPROM Micr
63. es you to configure the onboard serial ports Serial Port 1 Address This option is used to assign or disable the I O address and IRQ for the onboard Serial Port 1 Default is 3F8 IRQ4 Serial Port 2 Address This option is used to assign or disable the I O address and IRQ for the onboard Serial Port 2 Default is 2F8 IRQ3 27 Chapter 3 BIOS USB Configuration Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY USB Configuration Enables support for legacy USB AUTO option disables Module Version 2 24 3 13 4 legacy support if no USB devices are USB Devices Enabled connected 1 Keyboard 1 Mouse Legacy USB Support Enabled Port 64 60 Emulation Disabled USB Functions 8 USB Ports USB 2 0 Controller Enabled lt Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc USB Devices Enabled displays USB devices currently detected Legacy USB Support enables support for legacy USB devices Select Auto to disable legacy support if no USB devices are connected Port 64 60 Emulation Enable and disable USB keyboard legacy support for non USB aware operating systems USB Functions enables and disables USB host controllers USB 2 0 Controller Mode configures the USB 2 0 controller in HiSpeed 480Mbps or FullSpeed 12Mbps 28 PCI Configuration Chapter 3
64. he system mount a local IDE CD DVD ROM to the remote server Redhat AS3 0 Linux kernel 2 4 x Using LILO 1 In the line etc 1lilo conf add the following append xxx ide scsi whereas xxx is the ID for the IDE CD DVDROM to support For example lilo conf boot dev had map boot map install boot boot b timeout 50 message boot message image boot vmlinuz 2 4 21 40 EL label linux initrd boot initrd 2 4 21 40 EL img read only Quanta Confidential 53 62 root dev hdal append hdc ide scsi append hdd ide scsi Using GRUB If you are using GRUB to boot 1 To the end of the kernel line add the following etc grub conf xxx scsi whereas xxx is the ID for the IDE CD DVDROM to support For example grub conf default 0 timeout 10 splashimage hd0 0 grub splash xpm gz title Red Hat Enterprise Linux AS 2 4 21 40 EL root hd0 0 kernel vmlinuz 2 4 21 40 EL ro root LABEL hdc ide scsi hdd ide scsi Reboot and verify by using the line that follows ls al dev cdrom Ensure the message displays as below lrwxrwxrwx 1 root root dev cdrom gt dev scd0 86 Appendix A Updating the BMC Firmware BMC Firmware Update Utility The BMC Baseboard Management Controller firmware update utility is a DOS based program used to update the BMC firmware code This utility should only be run if new firmware code is necessary BMC Firmware Update Procedure Before proceeding rea
65. he E mail Notification tab enables you to configure e mail SMTP server sender and receiver details for system events notification Click the E mail Notification tab to display the following web page Embedded Server Manager System information System Monitoring Network Email Netifeatian Platform Event Filer Clack Setings System Management Accacs User Management RemoteControl Maintenance Fnabie E nal Notion Si Server Sondor Receiver E mail Address Enter server sender and receiver details and click Submit Platform Event Filter The Platform Event Filter tab allows you to modify the Trap Receiver Destination Address Click the Platform Event Filter tab to display the following web page Embedded Server Manager System Information System Monitoring Network E mail Notiicaton PlaformEver CloskSatings System Management Access User Management Remote Control Maintenance Piettorn Event Fiter PEF Global Control enan ver O pisatie PEF community Trap Receiver Destination Adress IP across B12 168 459 _ ell EZ natis Power off Action EZ ensis Power Cycle Action IM Erie Braver Reset inn Clock Settings The Clock Settings page enables the Administrator to set the time for the server 1 Click the Clock Settings tab to
66. ill the free area in FO00h segment with OFFh Initializes the Microsoft IRQ Routing Table Prepares the runtime language module Disables the system configuration display if needed A4 Initialize runtime language module AT Displays the system configuration screen if enabled Initialize the CPU s before boot which in cludes the programming of the MTRR s A8 Prepare CPU for OS boot including final MTRR values A9 Wait for user input at config display if needed AA Uninstall POST INT1Ch vector and INTO9h vector De initializes the ADM module AB Prepare BBS for Int 19 boot AC End of POST initialization of chipset registers B1 Save system context for APM 00 Passes control to OS Loader typically INT19h 46 Chapter 3 BIOS DIM Code Checkpoints The Device Initialization Manager module gets control at various times during BIOS POST to initialize different BUSes The following table describes the main checkpoints where the DIM module is accessed Checkpoint Description 2A Initialize different buses and perform the following functions Reset Detect and Disable function 0 Static Device Initialization function 1 Boot Output Device Initialization function 2 Function 0 disables all device nodes PCI devices and PnP ISA cards It also assigns PCI bus numbers Function 1 initializes all static devices that include manual configured onboard peripherals mem ory and I O decode window
67. information System Monitoring Configuration User Management Remote Cor SERE erromero roxas Information Bar Did you notice the Information Bar The Information Bar alets you to security related conditions for example f a potentially unsafe fle or pop up was just blocked f a webpage does not display proper look forthe Information Bar at the top of the page and cick t Dont show this message again Leam about the infomatinBar Cee 69 Chapter 4 Using the Web UI 3 Click Close and then right click the Information Bar to open the following screen ng files to rammi tar Clic here fer options What s the Risk More information 4 Click Download File The following screen appears Warning Hostname Mismatch The name of the site does not match the name on the certificate Do you want to run the application Name 192 168 1 2 Publisher localhost localdomain C3 5 Click Run Note dw You may see several security screens during installation of the remote application On each screen click Yes to continue The Java Remote KVM application appears Video uatay Hotkey Some 0 Cmm LEES EE Windows Server 2003 asl pS emen Lue Oe seamen 24 ts Mam cos 6 Click OK The remote window opens From here you can control the remote client 70 Chapter 4 Using the Web UI Using the J
68. ions to install CPUs 1 Remove the CPU dust cover by lifting the tab marked Remove 2 3 10 Chapter 2 Installing Hardware 4 Locate the notches on the CPU and the socket WARNING The QME 2200 uses LGA 771 sockets Zero Insertion Force socket which are designed for trouble free insertion of CPUs After placing a CPU into the socket press the lever down and lock in place If you notice any resistance when inserting the CPU ensure that it is aligned correctly 5 Align the notches and drop the processor into the socket Notch 6 Replace the CPU bracket and locking lever to lock the processor in place 7 Repeat steps 1 through 6 for the second CPU Chapter 2 Installing Hardware Installing the Heatsinks Refer to the following instructions to install heatsinks 1 Apply thermal compound evenly on the top of the CPU 2 Remove the protective cover from the underside of the heatsink 3 4 Tighten the four retaining screws clockwise in the order shown to secure the heatsink 5 Repeat steps 1 through 4 for the second heatsink WARNING A If the server board is to be operated with only a single processor both heatsinks must be installed to insure proper cooling Chapter 2 Installing Hardware Installing Memory The server board has eight FBD DDR2 DIMM slots for the installation of up to eight memory DIMMS DDR2 533 667 800 memory chips See Serverboard Components on page 2
69. isk inside LED As No Disk inside LED behavior status status Mount Begin Light On about 1 5 min Blinking On 3 5 sec Off 2 5 sec Blinking On 3 5 sec Off Ready 2 5 sec None No Media None Blinking On 3 5 sec Off 2 5 sec Note When the virtual floppy is mounted it does not lock on the client site It is recom mended that the client does not access the client floppy file even file write remove USB CD ROM Emulation When CD ROM Emulation function is enabled the managed server will find a USB CD ROM drive User puts the target CD into the remote console PC CD ROM drive While managed server will access this virtual attached USB CD ROM AST2000 will redirect to the CD in console PC and Java Remote KVM will access the target CD instead The CD format only supports data CD in Mode 1 and Mode 2 Form 1 It does not support VCD and CDDA USB Flash Disk Emulation When USB Flash Disk Emulation function is enabled and with the USB flash disk inserted to console PC USB port the managed server will find a USB removable drive While managed server access this virtual attached USB flash drive AST2000 will redirect to the flash disk in console PC and Java Remote KVM will access the target flash disk instead The diskette access includes Read Write CD DVD ROM Emulation Java RKVM can read CD DVD ISO image file and emulate a CD DVD ROM on the managed server Now we only support ISO9660 format Note When
70. lleur du Canada CE Declaration of Conformity EUROPE only This product has been tested in accordance to and complies with the European Low Voltage Directive C 73 23 EEC and European EMC Directive 89 336 EEC The product has been marked with the CE Mark to illustrate its compliance ii CCC China only The following CCC EMC Warning is marked on the product EMC Warning are required for Class A m products IAS i TE DA REE AET IB PEAY RECT THE China RoHS Declaration Table M FEEST Component Name Hazardous Substance 4f R Ha TER BIA BIRANI Lead Mercury Cadmium Chromium VI Polybrominated Polybrominated Pb Hg Cd Compounds Biphenyls Diphenyl Ethers Cr6 PBB PBDE ARETE 7 o o Chassis Subassembly um Power Supply d E ETHE Printed Board o o o o o o Assemblies PBA o Sen ZARA AIPA BTS J T 11363 2006 FIEEHGEREREESERELTS o Indicates that this hazardous substance contained in all homogeneous materials of this part is below the limit requirement in SJ T 11363 2006 iii BSMI Tawain only The following BSMI EMC Warning is marked on the product BSMI ID No and EMC Warning are required for Class A products ig PRR VERS TEE AS RRR RAAT gt SHEEP gt Aa ERRARE Wr Copyright This publication including all photographs illustrations
71. n on the toolbar highlighted in red or by clicking Control on the main menu and selecting Mouse Sync Note As the mouse is asynchronous after clicking mouse synchronization ensure that mouse acceleration is turned off To turn off the mouse acceleration function e InSolaris Linux use xset m 1 1 at the command line e In Windows XP and Windows 2003 Click Control Panel Mouse Pointer Options and uncheck the en hance pointer precision option e In Windows 2000 Click Control Panel Mouse Motion Acceleration None 76 Chapter 5 Using the Client Hide Console Side Mouse You can hide or show the console side local mouse by clicking the Local Cursor button on the toolbar or by clicking Control on the main menu and selecting Local Cursor Hardware Cursor Mode AST2000 provides the means to separate mouse data from video data and send the cursor position directly to the console side after positional updates or icon changes In this mode video image transmits become fewer and mouse movement becomes smoother Click Control Hardware Cursor on the menu to enable this mode Keyboard LED and Status Synchronization When NUM CAPS lock keys are pressed on the managed server s local keyboard the remote console side key board LEDs update automatically Conversely when you press these keys are pressed on the console side keyboard the remote managed server s keyboard LE
72. nly occur on systems using ECC enabled memory modules ECC memory has the ability to correct single bit errors that may occur from faulty memory modules A multiple bit corruption of memory has occurred and the ECC memory algorithm cannot correct it This may indicate a defective memory module Parity Error Fatal Memory Parity Error System halts after displaying this message Boot Message Displayed Boot Failure Description This is a generic message indicating the BIOS could not boot from a particular device This message is usually followed by other informa tion concerning the device Invalid Boot Diskette A diskette was found in the drive but it is not configured as a bootable diskette Drive Not Ready The BIOS was unable to access the drive because it indicated it was not ready for data transfer This is often reported by drives when no media is present A Drive Error The BIOS attempted to configure the A drive during POST but was unable to properly configure the device This may be due to a bad cable or faulty diskette drive Insert BOOT diskette in A The BIOS attempted to boot from the A drive but could not find a proper boot diskette Reboot and Select proper vice Insert Boot Media in selected Boot de media drive does not contain media Boot device or BIOS could not find a bootable device in the system and or removable NO ROM BASIC This message occurs
73. ntenance web page enables you to upgrade the firmware and reset the BMC Firmware Upgrade Use the Firmware Update feature to upgrade to the latest firmware version See BMC Firmware Update Utility on page 87 for more information on upgrading firmware Click the Firmware Update tab to view the following web page Embedded Server Manager Ee System Information system Monitoring Configuration User Management Remote Control_ Maintenance Firmware Upgrade Reset Mc Fewer upgrade A firmware upgrade will cause the server ard ENC ta he reset It ie recommended that a clean shutdown af the servar be dore prior ta the upgrade procedure An upgrade takes about 6 minutes to complete EMC will enter a special made ta load new firrware No other tasks can be performed in BMC until the firmware upgrade is complete and BMC is raset Reset BMC Use the Reset BMC web page to reset the BMC to the factory default configuration 1 Click the Reset BMC tab to view the following web page Embedded Server Manager Systeminformation System Monitoring Configuration User Management Remote Control Firmware Upgrade Reset SMe eset oc Reese wat po 1 minute for he BMC 1o reset betore reconnecting 2 Click Reset BMC to restore the default values This concludes this chapter The next chapter describes using the Client in more detail 73 Chapter 5 Using the Client Chapter 5 Using the Client
74. o support IDE devices with capacities greater than 504 MB Block Multi Sector Transfer enable this field if your IDE hard drive supports block mode Block mode en ables BIOS to automatically detect the optimal number of block read and writes per sector that the drive can support and improves the access speed to IDE devices PIO Mode each IDE channel supports a master device and a slave device This item lets you assign the kind of PIO Programmed Input Output used by the IDE device Choose Auto to let the system auto detect which PIO mode is best or select a PIO mode from 0 4 DMA Mode each IDE channel supports a master device and a slave device This mainboard supports UltraDMA technology which provides faster access to IDE devices If you install a device that supports UltraDMA change the appropriate item on this list to Auto S M A R T the S M A R T Self Monitoring Analysis and Reporting Technology system is a diagnostics tech nology that monitors and predicts device performance S M A R T software resides on both the disk drive and the host computer 23 Chapter 3 BIOS The disk drive software monitors the internal performance of the motors media heads and electronics of the drive The host software monitors the overall reliability status of the drive If a device failure is predicted the host software through the Client WORKS S M A R T applet warns the user of the impending condition and advises appropriate action
75. ocessor C7 Early CPU Init Exit 0A Initializes the 8042 compatible Key Board Controller 0B Detects the presence of PS 2 mouse 0C Detects the presence of Keyboard in KBC port 0E Testing and initialization of different Input Devices Also update the Kernel Variables Traps the INTO9h vector so that the POST INTO9h handler gets control for IRQ1 Uncompress all available language BIOS logo and Silent logo modules 13 Early POST initialization of chipset registers 24 Uncompress and initialize any platform specific BIOS modules 30 Initialize System Management Interrupt 2A Initializes different devices through DIM See DIM Code Checkpoints section of document for more information 2C Initializes different devices Detects and initializes the video adapter installed in the system that have optional ROMs 2E Initializes all the output devices 31 Allocate memory for ADM module and uncompress it Give control to ADM module for initializa tion Initialize language and font modules for ADM Activate ADM module 33 Initializes the silent boot module Set the window for displaying text information 37 Displaying sign on message CPU information setup key message and any OEM specific infor mation Chapter 3 BIOS Checkpoint Description 38 Initializes different devices through DIM See DIM Code Checkpoints section of document for more information
76. ocode Error BIOS could not find or load the CPU microcode Update to the CPU This message only applies to INTEL CPUs The message is most likely to appear when a brand new CPU is installed in a motherboard with an outdated BIOS In this case the BIOS must be updated to include the microcode Update for the new CPU NVRAM Checksum Bad NVRAM Cleared There was an error in while validating the NVRAM data This causes POST to clear the NVRAM data Resource Conflict More than one system device is trying to use the same non shareable resources Memory or I O NVRAM Ignored The NVRAM data used to store plug and play PnP data was not used for system configuration in POST NVRAM Bad The NVRAM data used to store plug and play PnP data was not used for system configuration in POST due to a data error Static Resource Conflict Two or more Static Devices are trying to use the same resource space usually Memory or I O PCI I O conflict A PCI adapter generated an I O resource conflict when configured by BIOS POST PCI ROM conflict A PCI adapter generated an I O resource conflict when configured by BIOS POST PCI IRQ conflict A PCI adapter generated an I O resource conflict when configured by BIOS POST PCI IRQ routing table error BIOS POST DIM code found a PCI device in the system but was un able to figure out how to route an IRQ to the device Usually this error is causing by an inc
77. oded information specific to your company and domain name You can generate a CSR or upload a manually created CSR Embedded Server Manager System formation System Monitoring Configuration User Management Remote Control Maintenance Newok Emal Notiicaton Plato Event Pilier Clock Settings System Nanagement Access ESL Cortieato che SSL contguraton FI in fne cita telov end cm Oreriztn Unito e Orgerizatior C A County Code C Locat E sates a Follow these instructions to generate and upload a CSR 1 Fill in the information in the fields provided Common Name CN the domain name for which you are requesting the SSL certificate Organization Unit OU whichever branch of your company is ordering the certificate Organization O legal Company or Personal Name as legally registered in your locality Country Code C the two digit code for a country Select the country from the drop down list Locality L city or location for example Los Angeles State S state for example California E mail Address E your email address Click Generate UC we ooo ee A CSR key is generated and uploaded automatically 64 Chapter 4 Using the Web UI Uploading a Manually Created CSR l Click the Browse button next to Certificate Upload and browse to the location of the saved key for example Savekey pem SSL Configuration Ce
78. omplete description of the PCI Interrupt Routing of the system Timer Error Indicates an error while programming the count register of channel 2 of the 8254 timer This may indicate a problem with system hardware Interrupt Controller 1 error BIOS POST could not initialize the Master Interrupt Controller This may indicate a problem with system hardware Interrupt Controller 2 error BIOS POST could not initialize the Slave Interrupt Controller This may indicate a problem with system hardware CMOS CMOS Date Time Not Set The CMOS Date and or Time are invalid This error can be re solved by readjusting the system time in AMIBIOS Setup CMOS Settings Wrong CMOS settings are invalid This error can be resolved by using AMIBIOS Setup CMOS Checksum Bad CMOS contents failed the Checksum check Indicates that the CMOS data has been changed by a program other than the BIOS or that the CMOS is not retaining its data due to malfunction This error can typically be resolved by using AMIBIOS Setup 51 Chapter 4 Using the Web UI Miscellaneous Message Displayed Description Keyboard Error Keyboard is not present or the hardware is not responding when the keyboard controller is initialized Keyboard Interface Error Keyboard Controller failure This may indicate a problem with system hardware System Halted The system has been halted A reset or power cycle is required to re
79. on or prevents the system from booting open BIOS and choose Load Optimal Defaults in the Exit menu to boot up nor mally BIOS SETUP UTILITY Server Main Boot Advanced Settings gt CPU Configuration gt ACPI Configuration gt IDE Configuration gt Super IO Configuration gt USB Configuration gt PCI Configuration gt MPS Configuration Branch 0 Specific Sparing Branch 1 Specific Sparing Warning Setting wrong values in below sections may cause system to malfunction Security Exit Configure the CPU Select Screen ad Select Item Enter Go to Sub Screen Disabled F1 General Help Disabled F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc The mark gt denotes a sub menu Scroll to the item and press ENTER to access the respective sub menu 19 Chapter 3 BIOS CPU Configuration Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY Configure advanced CPU settings This should be enabled in order to enable or disable the Hardware Intel R Xeon R CPU X5482 3 20 GHz Prefetcher Disable Frequency 3 20 GHz Feature FSB Speed 1600 MHz CPU1 CPUID 10676 Cache L1 128 KB Cache L2 12288 KB CPU2 CPUID 10676 Cache L1 128 KB Cache L2 12288 KB Ratio Status Unlocked Min 06 Max 08 Ratio Active Value 7 Hardware Prefetcher Enabled lt gt Select Screen Adjacent Cache
80. onfiguration Channel Number 01 Channel Number Status Channel number is OK gt IP Address gt MAC Address gt Subnet Mask gt Gateway Address lt Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc 35 Chapter 3 BIOS Set IP Address Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY LETS EDIT ME SIT M Server T1 D RO gt C13 Select IP Mode on BMC IP Address Configuration Save and exit to work at the next boot Parameter Selector 03 IP Address Mode Static IP Address 192 168 077 087 Current IP address in BMC 192 168 077 087 lt Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 61 Copyright 1985 2006 American Megatrends Inc IP Address Mode Select server IP Address Mode Static IP Address or Dynamic Host Configuration Protocol DHCP Note ED Current IP address in BMC is dynamic and may change with configuration changes 36 Chapter 3 BIOS Set MAC Address Scroll to this item and press Enter to view the following screen BIOS SETUP UTILITY LETS EDIT M T M Server T1 D Oz C13 MAC Address Configuration Parameter Selector 05 Current MAC address in BMC XX XX XX XX XX XX lt Select Screen Select Item F1 General Help F10 Save and Exit ESC Exit
81. orm is displayed prompting for the username and password This authentication with SSL protection prevents unauthorized intruders such as hackers from gaining access to the AST2000 web server If authentication is passed the user can manage the server by privilege At the same time the PHP PHP Hypertext Preprocessor re cords all user information including user ID and privilege The following figure displays the user authentication web page 52 Chapter 4 Using the Web UI Embedded Server Manager https 192 168 1 87 Usemame Password The default username is root The default password is changeme After passing authentication the following web page appears ix 309r weour Embedded Server Manager S L tle Swsteminformaton System Monitoring Configuration User Management Remote Control Maintenance Versions Session Time Oul_ Components BMG Version Serer Board hvorallon a BIAC Version Desnan BMC version Devioe D 5 Devoe Revision o Frmware Revision ozi FM Revision 20 rop System Information The System Information tab enables you to view the Version Information enable session time out and interval and view Components options Click the System Information tab to view the following web page zer amr Embedded Server Manager oO te System information System Monitoring Configuration User
82. rtificate Upload rq Upload 2 Click Upload to upload the key 3 Once the upload is completed close the browser 4 Opena new browser and log in The certificate file is the CSR previously uploaded 5 After you have generated or uploaded the CSR click Submit to save the changes SNMP The SNMP page enables the Administrator to configure SNMP settings for communities and users Embedded Server Manager O ts Systeminformation System Monitoring Configuration User Management Remate Control Maintenance Network Emelinotteston_ Flefom venitte CioekSetings POEEM UER SUN settings Mi Select Suet Port 161 Else Requests Olt Protocol Pernt v2 protecat 7 va Protocol 65 Chapter 4 Using the Web UI User Management The User Management web page enables the administrator to change the administrative account password and to add modify and delete users and set user privileges Click the User Management tab to view the following web page Embedded Server Manager SEEN System Information System Monitoring Configuration User Management Remote Control Maintenance UserAecoun ADS Cenfguration User List Useineme Piviege Statue root saniristiator enable Changing the Administrative Password Follow these instructions to change the administrative password 1 Under the username root click Change Password The following scre
83. s in PCI PCI bridges and noncompliant PCI devices Static resources are also reserved Function 2 searches for and initializes any PnP PCI or AGP video devices 38 Initialize different buses and perform the following functions Boot Input Device Initialization func tion 3 IPL Device Initialization function 4 General Device Initialization function 5 Function 3 searches for and configures PCI input devices and detects if system has standard keyboard con troller Function 4 searches for and configures all PnP and PCI boot devices Function 5 configures all onboard peripherals that are set to an automatic configuration and configures all remaining PnP and PCI devices While control is in the different functions additional checkpoints are output to port 80h as a word value to iden tify the routines under execution The low byte value indicates the main POST Code Checkpoint The high byte is divided into two nibbles and contains two fields The details of the high byte of these checkpoints are as follows HIGH BYTE XY The upper nibble X indicates the function number that is being executed X can be from 0 to 7 0 func 0 disable all devices on the BUS concerned 1 func 1 static devices initialization on the BUS concerned 2 func 2 output device initialization on the BUS concerned 3 func 3 input device initialization on the BUS concerned 4 func 4 IPL device initialization on the BUS concerned 5 func
84. s readable 1028 SenearReacing o Status tall Embedded Server Manager System Information System Monitoring Configuration User Management Remote Control Maintenance SensorReading EventLogs Locatorindicator Fault LED Summary Chassis Intrusion Fan Temperature Voltage Menu CPU Temp CPU 2 Temp Systemt Temp Description CPU 1 Temp Upper critical threshold is readable 780 Upper non recoverable threshold ie readable 800 SensorReading o Status oK ToP Description CPU2 Temp Upper critical threshold is readable 780 Upper non recoverable threshold is readable 80 0 SensorResding oo Note Click the hyperlinks as the top of the screen to view associated information 58 Chapter 4 Using the Web UI ltage Click the Voltage tab to view system component voltage information Embedded Server Manager CHEN System Information System Monitoring Configuration User Management Remote Control Maintenance SensorReading EventLogs Locatorindicator FaultLED Summary Chassis Intrusion Fan Temperature Voltage Vec 12V PV Vtt AUX 15V STB ESB2 4 5V Vee 3 3V Vec 5V FBD 1 5V Vec 1 5 Lan 1 2V STB Lan 1 9V STB Vce0 15V 3 3V STB Vcore 1 Vcore 2 Description Vee 12 Lower non citical threshold is readbe 11346 Lower crtica threshold is readable 10788 Leper non cr
85. that saves this information even when the power is turned off When the system is turned back on the system is configured with the values found in CMOS Configure such items as e Hard drives diskette drives and peripherals e Password protection from unauthorized use e Power Management features This Setup utility should be executed under the following conditions e When changing the system configuration e When a configuration error is detected by the system and you are prompted to make changes to the Setup utility e When redefining the communication ports to prevent any conflicts e When making changes to the Power Management configuration e When changing the password or making other changes to the security setup Note dw Only items in brackets can be modified Items that are not in brackets are dis play only BIOS Setup Options at Boot The user will be able to initiate SETUP by pressing the respective keys lt DEL gt Enter the BIOS Setup Chapter 3 BIOS Main Menu The main menu displays information about the server board and BIOS BIOS SETUP UTILITY Main Advanced Boot Server Security Exit USE ENTER TAB System Overview Or SHIFT TAB to Select a field AMIBIOS Use or to Version S87MB 1A11 011 Configure system Time BIOS Build Date 01 21 08 Product Name QR2 2700 QSSC 680 QME 2200 QSSC 680MB Product Board ID SATA SKU with PCIE X slot Board Serial Number QTFMOV7460001
86. the virtual floppy is mounted it does not lock yet on the client site we rec ommend that the client to not access the client floppy file even file write remove Note s Regarding the CD DVD ROM ISO image file we only support the data format We do not support any WAV Video and other extended formats for example If the Java Remote KVM customer selects an incorrect ISO format file compressed format No Media status is activated Click media change to select the correct ISO file 84 Chapter 5 Using the Client Multidevice Configuration Use the procedure below to configure OS specific managed devices on the server Redhat AS4 0 You are required to rebuild the initial ramdisk l In etc modprobe conf add the following line options scsi mod max luns xxx whereas xxx is the number of LUNs to support 2 Type the following to build the initial ramdisk and implement the changes mkinitrd f boot newimage 2 6 xx 2 6 xx whereas xxx is the exact kernel ver sion 3 Change the following boot grub menu lst nitrd To boot grub menu lst newimage 2 6 xx 4 Reboot the system After rebooting the LUNs appear Redhat 9 0 l Inthe line etc modules conf Add the following options scsi mod max scsi luns 8 2 Reboot 85 Chapter 5 Using the Client Virtual Storage Configuration Linux Kernel 2 4 Use the procedure below to configure your OS Linux kernel 2 4 on your local computer After configuring t
87. tical threshold is readable 12586 Leper crticalthreshoid is readable 13144 SensorReading 12090 ET ok Top Description py vit Lower non citical threshold is readsbils m Note Click the hyperlinks as the top of the screen to view associated information Event Logs Click the Event Logs tab to view reports about system events View Event Logs Click View Event Logs to view specific event information Embedded Server Manager eee System Information System Monitoring Configuration User Management Remote Control Maintenance SensorReading EventLogs Locatorindicator Fault LED ViewEventLogs SavetveniLogs Clear EventLogs Severity I Tmestene backward neseriptien iurerecites 18050405051520 Unspecified event lurspeciren 1803045051520 Urspeciied event Qicnecoseratie 180304105081520 Urspeciied event Qervecoverable 1903045 0815 20 Blos test CMOS System Orton Not Sat Qhtornation 1803045 061440 BAT 3V bakte normal htormatun 1905005 osa Processor 0 presence detected Qoa 490304 050514 38 BAT 3V is oo ow Value 0 000 Vols Thieshoe3 282 Vots ursreciten Urspecited evert irerecites Urepecited evert Duresecites Urspeciied event xursrecrea Urspetited evert urerecites Urspeciied evert hiermation Processor 0 presence dotecod e Severity indicates the nature of the event unspecified information critical etc e TimeStamp backward indicates the time and d
88. tted 2 Normal Few video loss and big size image transmitted 3 Low Some video loss and small size image transmitted The following image displays the video quality options 74 Chapter 5 Using the Client USB Keyboard and Mouse Emulation Once the AST2000 KVM over IP function is launched AST2000 emulates USB 1 1 keyboard and mouse devices As a result the managed server s BIOS or OS will detect the USB keyboard and mouse attached and load their drivers to service them The following image shows the managed server s device manager window Ee Acton iow Hob mjela E Windows Server 2003 The remote console sends keyboard and mouse input to the AST2000 which then receives and packs them in USB HID format and transmits them to the managed server through the USB interface and protocol Note d Mouse wheel operation only functions in the remote screen not remote console Screen 75 Chapter 5 Using the Client Mouse Synchronization at Console Side When the Java remote KVM application is launched on the console PC the mouse position of the remote server and the console are automatically synchronized However once the managed server s mouse is moved locally the console PC mouse position will be different from the redirected managed server mouse In order to re synchronize the mouse click the Mouse Synchronization butto
89. x SATA connectors 13 FRONT PANEL Front panel connector 14 PCI Slot 1 PCI slot supporting PCI X 64 100 15 PCI Slot 2 PCI slot supporting PCI X 64 133 16 PCI E Slot 3 PCI E slot supporting PCI E x 4 17 PCI E Slot 4 PCI E slot supporting PCI E x 4 18 PCI E Slot 5 PCI E slot supporting PCI E x 16 19 DDR2 DIMM array 4 DDR2 DIMM slots channels 0 and 1 SAS SKU Chapter 1 Introduction 2 345 EE eee RM i OO n Q en 4 ital 6 Q O m ER n i f O Sa flor i 18 L 17 E 16 I1 15 EM 14 E 5 E za r T Tre Tr i n peu I l J 13 12 e ape e eje g 1 I O ports See Input Output Ports on page 4 2 MAIN PWR Serverboard main power connector 3 IPMB connector Reserve power supply connector 4 12V connector Supports 12V power connection 5 DDR2 DIMM array 4 DDR2 DIMM slots channels 2 and 3 6 CPU 1 socket 771 pin CPU 1 socket for processor T CPU 2 socket 771 pin CPU 2 socket for processor 8 USB connector Front USB connector 9 CPU PWR1 CPU 1 power connector

Download Pdf Manuals

Related Search

Related Contents

Télécharger - Chemin de Compostelle  Samsung غسالة WDF900C Combo الضخمة من الداخل، سعة 10 كيلو دليل المستخدم  nativeKONTROL apC  DCG 230-D / DAG 230-D  Samsung 940MW Felhasználói kézikönyv  TuneCast® Auto LIVE for iPhone and iPod TuneCast® Auto LIVE  Audiovox XCH10RF User's Manual  7160-9001-531 DairyPlan C21 5.2 Installation Manual  User`s Manual - Content Paradise  JBL ESC200 Shelf System  

Copyright © All rights reserved. Failed to retrieve file