SK808 Owners Manual
Contents
1. Passive Infrared PIR High Bay Motion Sensor SK808 User Manual P SK808 General The SK808 PIR motion sensor is ideal for high bay applications such as warehouses and factories The sensor has an extruding screw that can easily be installed directly onto a light fixture If after reviewing this guide you require additional information or assistance please contact Eco Heat Equipment at info ecoheat co za 27 0 861 999 887 or www ecoheat co za Technical Specifications Voltage 220 240V AC Frequency 50 60Hz Load Incandescent 1 000W Fluorescent 600W Detection Range 360 1 8m radius Light level 10 1 000 LUX Time setting 10 seconds 30 minutes Installation height 4 12m max Safety Any incorrect use or installation procedure not recommended by the manufacturer may cause fire electrical shock or injury to persons Box Contents Your box should contain the following items Sensor Installation Instructions WARNING ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES AND STANDARDS Note motion sensors respond to rapid changes in temperature so care should be taken not to mount the device near a climate control source i e heaters or air conditioners Hot or cold draughts will seem like body motion to the sensor and will trigger the device Recommended distance from climate control devices is 2m 1 Turn power off at circuit breaker or fuse 2 Connec2. eat Equipment products visit www ecoheat co za or phone 27 0 861 999 887 Indemnity The Author and supplier shall not be held liable for any loss injury or damage of whatsoever nature whether consequential or not either contractual sustained to or caused by or which may arise through the use of any comments suggestions circuitry services or equipment offered for purchase The User indemnifies the author and supplier and agrees not to hold him her responsible for any damages losses and or liabilities including legal costs on a scale as between attorney and user arising from or through the use of circuit diagrams equipment and services whether such circuit diagrams equipment and services were used with the consent of the User or not All risks attached to the use of circuit diagrams equipment and the connection thereof to the User s equipment shall be deemed to have passed onto the User once having purchased such equipment from the author or supplier is T ec sensor 2 of 2
3. ion range 2 TIME time delay after motion sound until shut off 3 LUX LIGHT level of ambient light sensitivity The three adjustments settings are as follows Detection range Im to 8m Time setting range 10sec to 30min Lux light sensitivity 10 to 2 000 LUX 1 of 2 Manual Override For manual control the SK808 motion sensor features a convenient push button switch If the lights are OFF pressing the button will turn the lights ON for as long as the room is occupied The lights will turn OFF once the room is vacant after the delayed OFF time expires If the lights are ON pressing the button will turn the lights OFF and keep them OFF even if the room is occupied This feature is particular useful for presentations or when the automatic motion sensor settings need to be overridden The lights can be turned back ON by simply pressing the button The sensor will return to normal operation Motion Sensor Adjustments Push Button LUX RANGE TIME The motion sensor s settings can be adjusted as follows Step 1 Adjust the TIME setting to minimum Turn the TIME control fully anti clockwise to set to the 10sec testing setting Step 2 Adjust the LUX LIGHT setting to maximum Turn the LUX LIGHT fully clockwise to set to maximum sensor functioning in all lighting conditions Step 3 Adjust the RANGE setting Turn the RANGE control fully anti clockwise Move away from the sensor until the LED stops blinking Th
4. is will be the maximum detection range To lengthen the range turn the control clockwise until the desired distance is reached 1m 8m maximum Step 4 Adjust the TIME setting Turn the TIME control clockwise until the required delay is reached 10sec testing 1 10mins 2 20mins 3 30mins Factory time out is pre set to 10 seconds NOTE All the time intervals are within approximately 10 seconds of the stated time out interval WARNING Controlling a load in excess of the specified ratings will damage the unit and lights and could pose risk of fire and electric shock WARNING Do not install this unit to control a power socket OTHER CAUTIONS Disconnect power when working on electrical outlets or components Do not push on the surface of the lens Cleaning Carefully wipe sensor with a soft damp cloth Do not apply pressure to the lens Recycling Please recycle all packaging material that came with the motion sensor Eco Heat Equipment August 2015 Trouble Shooting The unit will No mains power not switch No movement is b Move towards the unit in on detected in detection detection zone or increase the zone detection range settings Wrong LUX LIGHT level Adjust setting on the LUX LIGHT setting settings Electrical circuitry faulty Refer to the Electrical Installation section to ensure correct installation Have a certified electrician disconnect and test the unit Con
5. t wires as per diagram 3 Sensor can be secured onto light fitting 5 Restore power at circuit breaker or fuse Sensor calibration Note Allow up to 1 minute for the motion sensor to recalibrate after it has been connected for the very first time This is only necessary during installation or when the mains supply is disconnected Eco Heat Equipment August 2015 Installation wire diagram Red Live In Red Live In Power Supply 220 240V AC 50 60Hz Brown to Load Black Neutral Neutral Operation and Field of View The motion sensor detects motion within its coverage area and controls the associated lighting connected to the sensor The passive infra red PIR sensor is sensitive to the heat emitted by the human body In order to trigger the sensor the source of heat must move from one zone of detection to another The device is most effective in sensing motion across its field of view and less effective sensing motion towards or away from its field of view Sensor detection range from side large motion OO 1 O80 OOOO Sensor detection range from top large motion e a mM Motion Sensor Settings and Adjustments The motion sensor is a Passive Infra Red PIR type electronic occupancy detector which in turn switches the lights when connected to the motion sensor There are three adjustments that can be made to influence the operation of the motion sensor 1 RANGE motion detect
6. tact Eco Heat Equipment a Check mains power is on Electrical Installation not done correctly Unit may be faulty Unit stays Continuous movement in g Check detection range setting on detection zone and reduce detection range The sensor is not sensitivity mounted correctly for h Check detection range setting reliable operation and mounting procedure Wrong LUX LIGHT level i Adjust setting on the LUX LIGHT setting settings Time setting control is set j Adjust the time setting control too far Unit may be faulty permanently k Contact Eco Heat Equipment Warranty The sensor has a three 3 year warranty after the date of the original purchase Please keep your original receipt as this will be required for any claims under this warranty The warranty is a strictly carry in policy The sensor s has to be returned to Eco Heat offices for a claim to be processed The warranty does not cover damage from misuse neglect or abuse products that have been modified in any way shipping and handling cost associated with the product damage resulting from accidents lightning fire water power surges natural disasters and or incorrect installation For more information view the Return Refund Policy at ecoheat co za terms ohp Due to minor improvements in design or otherwise the product you purchase may differ from the one shown in this leaflet For more information or advice on this or any other Eco H
Download Pdf Manuals
Related Search