SSW7-TS - Helmholz
Contents
1. Power supply Degree of protection Electromagnetic compatibility EMC Interference emission SSW7 TS 700 751 8VK21 105 x 53 x 29 mm LxWxH approx 180g incl MPI cable amp connector RS485 isolated 19 2 kbps to 187 5 kbps 1 2m no terminating resistors Connector SUB D 9 way RS232 serial asynchronous 9 6 kbps to 115 kbps Connector SUB D 9 way 24V DC 25 from the programmable control or external power supply polarized 30mA type 45mA max IP 30 Class B to EN55022 Interference immunity on signal lines 2kV acc to EN61000 4 4 Noise immunity ESD RF radiation fields Conducted RF interference Climatic conditions Temperature during operation Temp Storage transport Relative humidity operation Relative humidity storage Special features Quality assurance Maintenance SSWZ TS 6kV contact discharge EN61000 4 2 8kV air discharge EN61000 4 2 10V m acc to EN61000 4 3 10V acc to EN61000 4 6 20 C to 60 C 20 C to 60 C 5 to 85 at 30 C no condensation 5 to 93 at 40 C no condensation According to ISO 9001 2000 Maintenance free no battery Page 13 Pin assignment M24V DATA B RTS AS SUBD connector MPI n c OV M5V n c 24V DATA A RTS PG Connecting cable MPI extension cable 700 751 6VKx1 5 A eee Z 5 l TE im ANN s f T O S S a pon ooo bra a MIS PO ED RTS AS tp Eno fs ETS AS DATA A EY may EEE vou PAY Y ESPERES EEN E e l2. noz compatible with you SSWZ TS Teleservice via the MPI Bus 700 751 8VK21 User Manual Version 3 2005 11 29 HW 1 FW 3 0 and higher Systeme Helmholz Adapter fur MPI Bus LEDon LED flash Power JUpdac 8 Active Param 4 Connect Data 5 SSW7 TS TOU TAI EVEZI MPI an S7 HW 1 FW 3 00 SET Boos Order number of manual 900 751 8VK21 en Systeme Helmholz GmbH e Hannberger Weg 2 e D 91091 Grokenseebach Phone 49 9135 7380 0 e Fax 49 9135 7380 10 e E Mail info helmholz de e Internet www helmholz de All rights are reserved including those of translation reprinting and reproduction of this manual or parts thereof No part of this manual may be reproduced processed copied or transmitted in any way whatsoever photocopy microfilm or other method without the express written permission of Systeme Helmholz GmbH not even for use as training material or using electronic systems All rights reserved in the case of a patent grant or registration of a utility model or design Copyright 2009 by Systeme Helmholz GmbH Hannberger Weg 2 91091 Grossenseebach Germany Note We have checked the content of this manual for conformity with the hardware and software described Nevertheless because deviations cannot be ruled out we cannot accept any liability for complete conformity The information in this manual is regularly updated When using purchased products please heed the latest
3. dial Call Preferences Wait for dial tone before dialing Number of redial attempts Redial after Abbrechen Hilfe f Tone dialing Pulse dialing Assign Adapter Parameters Network Modem Serial Parameters Access Protection Connection Preferences Transfer rate 115200 Data bits Parity Stop bits Abbrechen Hilfe A The PG DIAL and AS DIAL functions for starting a call from an S7 CPU are currently not implemented Please consult the programming software manuals for further information ra The SSW7 TS can also be used as a normal PC adapter without the teleservice software The SSW7 TS automatically detects the mode after power on Modem operation Direct link PC adapter SSW7 TS Page 8 Modem setting The modem connected to the SSW7 TS is automatically initialized on power on or connection During initialization the initialization string that has been entered in the TeleService software is sent to the modem and a positive response OK is awaited AT amp F El LI MI Q0 V1 C1 SO 1 default AT Introducing modem commands SE Load factory settings of the modem El Echo of the ON command L1 Volume level 1 M1 Loudspeaker ON QO Feedback from the modem ON V1 Feedback in plain text amp C1 DCD signal shows carrier connected SO 1 only wait one ring Please see the modem manuals for the appropriate commands Tested modems with init strings DI
4. N rail mounted modem 56K analog SMALL 700 751 HSM21 DIN rail mounted modem ISDN 700 751 HSM02 Pocket modem 56K analog V2 700 751 MDMO6 Pocket modem ISDN 700 751 MDMO5 DIN rail mounted modem GSM 700 751 GSMO2 Sooooooo SSWZ TS Page 4 The connection to the MPI bus can be extended with an additional cable For that purpose Systeme Helmholz GmbH offers the following products MPI bus extension cable 5m 700 751 6VK11 MPI bus extension cable 10m 700 75 1 6VK21 MPI bus extension cable special length 700 751 6SO11 When extending the MPI bus please follow the relevant configuring guidelines as defined in the documentation of your PLC O l For the SSW7 TS a wall bracket a DIN rail bracket 700 751 HSHO1 and an S7 300 sectional rail bracket 700 751 PSHOO are available A FM35x modules can not currently be parameterized with the SSW7 TS LED displays The three LED s on the top of the device provide you with information about the operating status of the SSW7 TS You can use them to locate sources of error quickly The LED s have three different states Off on blinking If the LED is off none of the labeled states applies Upper LED off The adapter has no power or is faulty Upper LED on The adapter is being powered with 24V and the processor is running Center LED on The SSW7 has parameterized the modem correctly and registered in the MPI network Lower LED on The SSW7 has established a connection Low
5. N rail mounted modem 56K default DIN rail mounted modem 56K Small default Pocket Modem 56K analog default DIN rail mounted modem ISDN AT Z 123 AT amp FEILIM1Q0V1 amp C1S0 1 Pocket modem ISDN Internet AT Z 123 ATGFBIOE1LIMIQOVISC1S0 1 Pocket modem ISDN Profi AT Z 123 ATS amp FEILIM1IQOV1 amp C1S0 1 DIN rail mounted modem GSM AT CPIN 0815 AT amp FEILLIM1QO0V1 amp C1S0 1 ELSA MikroLink 56k pro 56k Industrial AT amp FEILIM1QO0V1 amp C1S0 1 ES 3 2 4 3Com U S Robotics 56k AT amp FIEILIM1Q0V1 amp C1S0 1 Westermo DIN rail mounted modem TD 32 AT follow instructions in Westermo manual Westermo DIN rail mounted modem ID 90 AT follow instructions in Westermo manual Siemens GSM modem TC35 AT CPIN 0815 ATSFE1L1M100V18C1S0 1 ELSA Microlink ISDN AT IMSN 0 123 ATSFE1L1M100V18C15S0 2 123 is only an example The HELMHOLZ ISDN TA is programmed to multipoint connection default on the SO bus and the MSN must be configured 0815 is only an example Enter your four digit PIN number here If you are using GSM applications have your provider enable your SIM card for data transfer SSWZ TS Page 9 If the DIN rail mounted modem 56K is used outside Europe the following init string must be used AT GCI xx EILIM1Q0V1 amp C1S0 1 xx stands for the country code which you will find in the user manual of the DIN rail mounted modem The semicolon in the init string is obligatory ESO If you are using a
6. SECS Dialing Properties Monitoring Times Acknowledgment characters Automatically ll Data Connection Preferences Port speed 1 3200 ho Data Protocol Standard EL vw Compression Flow contro Hardware v Cancel Help i For safety reasons Forced EC error detection must always be activated In the case of a link without error checking sporadic broken connections can occur To test your teleservice software and the modem on the PC you can dial our SSW7 TS test system The phone number can be obtained from our Support Co SSWZ TS Page 7 Installing and parameterize the modem in the system The modem in the system is directly connected to the SSW7 TS The SSW7 TS puts the modem in receive mode as soon as it is switched on and has established a link to the PLC An initialization string is stored in the SSW7 TS for that purpose This string can be changed with the software Parameterization can be performed both locally on the workstation SSW7 TS in direct link or via a telephone connection SSW7 TS in modem connection If you have to adapt the init string use the relevant command sequences given in the modem manuals or ask your modem manufacturer Example Parameterize the SSW7 TS Assign Adapter Parameters Netmork Moder Serial Parameters Access Protection Modem Settings Initialization A4TH Location The phone system uses To access an outside line first
7. d Therefore you have to install the Speed up driver V3 0 The actual version is available at www helmholz de Is there an older high speed driver running you MUST close AND uninstall this A before continuing The Speed up tool creates a new serial COM port The driver brings the data transfer from the virtual to the physical COM port and vice versa After the installation start the driver via the symbol in the start menu There is only an additional symbol in the systray ONO 18 22 Right click to symbol opens the context menu for the properties Properties 1 Activate the new virtual Interface COM port in the dialog box Virtual COM port pow cs ore e 2 s t COM port where Sete COM pout comi The COM port where the 557 is connected the SSW7 TS 1S plugged 111 Baud rate 1115200 3 Set the baud rate you want TER to use w Load program automatically on system start Language English Mi coros Select the OK button to activate the driver N GE 1620 This new COM port has to be used from your applications now For more details please see the documentation for SSW7 driver software Right click to symbol opens the menu select end for deactivating the Speed up tool SSWZ TS Page 12 Technical data Order number Dimensions Weight MPI interface Type Transmission rate Cable Connection Communication interface Type Transmission rate Connection Power supply Voltage
8. er LED blinking The SSW7 is transmitting data If the SSW7 TS on the system is connected to the modem and the PLC it will establish contact with the MPI bus as soon as the modem has been successfully initialized The upper and center LED s should therefore light up after a short time I If only the upper LED lights up either the modem has not responded to initialization or the SSW7 TS has not joined the MPI bus SSWZ TS Page 5 Parameterization The SSW7 TS settings are always defined in the software used for communication with the programmable controller In most cases you will also need an additional software module for your programming software e g TeleService from Siemens version 3 0 and later to parameterize the SSW7 TS and operate the connection telephone book of dial able systems Example Setting up a system A i sample tel F Programme SIEMENS TeleService s fwts TFT Haele eur all pil Plant Comment Plant Data Hame Company Street City Phone Number Number Country Press Fl for help Example Dialing up the SSW7 TS Set PGJPC Interface Access Path SSW7 TS Access Font of the Application S7ONLINE STEP 7 gt TS Adapter v Standard for STEP 7 Interface Parameter Assignment Used TS Adapter Properties NetLink PROFIBLUS PL Adapter Sto PC Adapter M Pl PC Adapter PROFIBUS TS Adapter Assigning Parameters to the Device Driver for y
9. g 5Y TE e ASA 3 A ML CA AA ee is 1 PC to SSW7 TS for direct operation on the PC Signal direction 5 9 1 qa Nd st E gt PS Ds gt om AH me ens A AAA a O PAN l ple aS a oo a E AS JA gt RTS E A A A core pa xe a E On BR es a n Ri lt lt nan Gnd 1 a MP1 Adapter Page 14 SSWZ TS
10. n ISDN modem you must select a driver in the Teleservice A software which supports protocol X 75 Connection possibilities analog ISDN GSM SSWZ TS Page 10 SSWZ TS parameterization software With the SSW7 Tool V3 it is possible to pre parameterize an SSW7 TS with any computer even if there is no TeleService software installed on that computer SHTools v3 02 File Adapter Diagnostic Help Language gt Station related PG PC is the only master in bus Adress m Net related Baudrate Highest subscriber adress EEx 187 5 kBit s E x Mainsettings Abort Save 7 End COMI xxx 251 8V4K 21 5547 ve 5 Teleservice Once set parameters can be stored on the computer in a file and transmitted to further SSW7 TS s Settings TS Adapter KI Network F Modem T Parameter a Access protection Modern settings Initialization call settings Wait for free tone before dialing fe MF Tone dial Po Ww Pulse dial Exchange number BT fo Number of redials Redial after Mainsettings Abort Save f End KI Network E Modem T Farameter amp Access protection Mame Passwords Ring back number Mame Password Mainsettings Abort Save f End The SSW7 Tool V3 can be obtained from our download area on our Internet site www helmholz de SSWZ TS Page 11 Speed up driver for Win 2000 and XP In direct mode the SSW7 TS can work with 115Kbau
11. our TS Adapter Interface Add Remove Select Testanlage LPUS12 Systeme Helmholz GmbH Gewerbegebiet Ost 36 91085 Weisendort 09135 738060 Deutschland 49 y Abbrechen Hilfe offline Properties 15 Adapter Network Local Connection f Direct Connection to Transmission Aate te Modern connection Default Cancel Help Cancel Help Page 6 Installing the local modem If you have already installed a modem under Windows you can also use this modem for teleservice Plug and play modems are automatically recognized by the PC and integrated in the system as soon as they are connected The driver supplied with the modem is required for this You can manually install modems without plug and play capability via the control panel under the Telephone and modem options in the Modems dialog box Here again you will need the driver supplied with the modem It should be possible to address the modem as soon as you have installed it on one of the COM interfaces of your PC Select the installed mode in the parameterization of the programming software Example Setting the local modem Customize x INSYS Pocket 56k Modem Default Preferences Ed Modem Connection Modern INS Y5 Modem 56k TeleService specific Properties Location General Advanced Call preferences Disconnect a call if idle for more than o mins Cancel the call if not connected within
12. version of the manual which can be viewed in the Internet at www helmholz de from where it can also be downloaded Our customers are important to us We are always glad to receive suggestions for improvement and ideas Step and SIMATIC are registered trademarks of SIEMENS Design With the SSW7 TS teleservice of a system can be performed via the MPI bus using standard commercial type modems At the RS232 end baud rates of 9 6 Kbaud to 115 Kbaud are supported The SSW7 TS has a 1 2 m long connecting cable which can be directly plugged into the CPU socket of the programmable controller or at any other point in the MPI HH network Modem Modem DIN rail PC type or or commercial modem commercial modem The housing of the SSW7 TS contains a 9 way sub D connector whose pin 23 SETE assignment is designed for a standard E i modem cable for direct connection to a 1 2 meable length standard commercial type modem optional extension cable The SSW7 TS receives its power supply from programmable controler W7 POPC the CPU via the MPI cable If 24V are not available at the point of connection or if several SSW7 TS are connected to a CPU at the same time 24V can be fed from an external source For teleservice of the SSW7 TS standard commercial type modems that support the Hayes command set can be used We recommend the following modems for use with the SSW7 TS DIN rail mounted modem 56K analog 700 751 HSM11 DI
Download Pdf Manuals
Related Search