Mp 700 Wash - Acctech.ru
Contents
1. Should there be different electrical characteristics or special steps to be carried out See par 3 2 please contact COEF by telephone or e mail elettronica coef it Supply the projector by connecting it as indicated in picture PHASE GROUND NEUTRAL T 4 1 DMX 512 CONNECTIONS Connect the projector and the control unit to a wire in conformity with the EIA RS 485 standards braided bipolar shielded 120 ohm of characteristic impedance 22 24 AWG equipped with Cannon 3 Pin XRL plugs Respect the DMX 512 signal input and output according to the panel indications A terminal pin with 120 ohm resistance 74 Watt minimum must be inserted between the terminals 2 and 3 in the last piece of apparatus FROM CONTROL UNIT L CPN j Ultimo proiettore della catena DMX W w The last projector of the DMX chain y http www coef net info coef it Pag 7 5 0 SPECIAL FUNCTIONS AND PROJECTOR ASSIGNMENT On the front panel of MP700 Wash you ll find a section for the additional functions and for setting the projector Following the picture you can see all the offered possibiliti es in detail All operations are to be carried out with the E F G H but tons respectively indicated as MENU ENTER DOWN and UP The display D will inform you about the selected functions The 3 A B and C leds will allow you to know A reception of the DMX line B lamp ON C errors indicated on the ERR table see tab2. evidencing the operation dangers and the necessity of technical support Please find here below a list of symbols and relative meaning OPERATOR Not particulary qualified staff that can operate when no specific knowledge is required COEF OPERATOR Technical staff qualified and trained by the constructor for repair and extraordinary operations N MECHANICAL OPERATORS Staff employed in the ordinary mechanical maintenance SPECIALIZED MECHANICAL OPERATOR Qualified staff employed in extraordinary authorized in stallations and repair SPECIALIZED ELECTRIC OPERATORS Qualified staff employed in extraordinary authorized instal lations and repairs f DANGER SIGNAL Generic dager signal and electric shock danger signal GENERAL WARRANTY CONDITIONS The guarantee is valid for a period of 12 months from the date of purchase of the equipment e The guarantee is not valid in case a wrong voltage or frequency is selected e The parts which are proved to have manufacturing defects are also covered by the guarantee The external parts of the equipment its removable elements and lamps are excluded from the guarantee for these parts we recommend to follow the directions supplied by their manufacturers e The guarantee is not valid in case of tampering or repairs carried out by non authorized personnel e The replacement of the equipment during the validity of the guarantee is not provided for The transport frei
3. will immediately invalid the COEF warranty 3 3 Settings for magnetic ballast Cod O2E012 The fixture can work at the following tensions 230 V 50 60 Hz and 208 V 60 Hz optional on re quest Please be careful to connect _ the cable to the right terminal that is relevant to the desired tension and _ frequency both on the ballast and on the transformer located in the MP700 Wash base Please carefully follow the indications shown in the A B pictures A and B 3 4 Settings for electronic ballast Cod 02E013 The fixture can work at the following ten sions 100V 60 Hz 120V 60 Hz 208 V 50 60 Hz 230 V 50 60 Hz 250 V 50 60 Hz You can modify the settings following the needs of the country were the fixture is instal _ led This operation is easily done by moving the cable to the right terminal of the electronic board transformer that is located in the base of the fixture The ballast electronic does not need any adjustment We recommend you to update the serigraphy table at the new value 3 5 PROJECTOR INSTALLATION To fix the MP700 Wash is necessary when the installation has to be on a raised from the ground support to block the quick lock release brackets of the unit by means of a screw provided with nut and locknut measuring not less than M10X850 to insert in the central pre arranged hole on the fi xing bracket In addiction to the provided quick lock release omega brackets in or
4. 55 gt 0 http www coef net info coef it Pag 11 8 0 LAMP ADJUSTMENT e Don t look directly the beam trough the lens e The lamp is pre regulated by the factory Only fine adjustment Don t move the screws C up to upper or lower extremities Lamp adjustment is necessary to obtain a uniform and powerful light beam Switch on the projector and set the channels without gobo and colors Adjust the three screws C until you reach the ideal condition between power and homogeneity 9 0 ORDINARY MAINTENANCE Ordinary maintenance on the projectors MP700 Wash is necessary to maintain the perfect effi ciency of the unit and to avoid defects like the low luminosity of the light beam or the elevated overheating of the equipment In the figures you can see those components that can easily accumulate dust and grease Clean them using a soft cloth and common glass cleaners CLEAN PULIRE 9 1 EXTRAORDINARY MAINTENANCE WARNING switch off the projector before operatinc To make an extraordinary mainte nance itis necessary the presence of a generic or qualified mechanical opera tor according to the type of the needed intervention Open the cover of MP700 Wash by the 4 fast screw Clean carefully the indicated parts Pag 12 http www coef it info coef it You must particularly take care of the sensors which are really fundamental in the unit working The sensors are absolutely necessary when a general r
5. OST 0 t 5 sec 12 156 170 from FROST 0 to FROST 100 t 5 sec 171 185 from FROST 100 to FROST 0 t 4 sec gt return to NO FROST fastly with continuous effect 186 200 from FROST 0 to FROST 100 t 4 sec gt return to FROST fastly with continuous effect 201 250 from FROST 0 to FROST 100 continuous effect and adjustable speed 251 255 FROST inserted DIMMER 0 5 DIMMER Closed 13 6 250 DIMMER Adjustment 251 255 DIMMER Open WARNING position CHANNEL 1 at a value between 6 and 250 in order to control DIMMER with this channel USE MODE only code 02E013 with Electronic Ballast 44 0 5 Studio mode 6 250 Adjustment 251 255 Live mode EFFECTS TIME ADJUSTMENT work on channels 2 3 4 9 10 11 12 13 15 0 5 NO delay 6 250 adjustment delay 251 255 MAX delay MOVEMENTS TIME ADJUSTMENT work on channels 5 7 16 0 5 NO delay 6 250 adjustment delay 251 255 MAX delay 7 1 SPECIAL ACTION When the lamp control via DMX CDMX and the reset via DMX RDMX function have been activated in the configuration menu its possible by a combination of the channels values to control the lamp switch ON OFF or to allow the projector MASTER RESET a Ee Lamp ON via DMX CHANNEL 2 value 0 CHANNEL 3 and CHANNEL 4 value 0 gt 255 gt 0 Lamp OFF via DMX CHANNEL 2 value 255 CHANNEL 3 and CHANNEL 4 value 0 gt 255 gt 0 MASTER RESET CHANNEL 17 value O CHANNEL 2 and CHANNEL 3 value 0 gt 2
6. Realizeb by PC CAD amp VIDEO H MP 700 W2 g E iG j i f x Jr EET Code 02E013 DVP Electronic Ballast Code 02E012 DV Magnetic Ballast e OPERATING INSTRUCTIONS Revision 1 Lighting Declaration of CE conformity We Manufacturer COEF srl Via Albinatico 80 82 51019 Ponte Buggianese Pistoia ITALY Declare that the product MP7OO WASH is in conformity with 89 336 EEC EMC directive and with the actual required safety standars in accordance with LVD 73 23 EEC Ponte Buggianese July 02 2002 ATTENTION carefully read the directions of this manual Exclusively follow the safety rules in force and do not carry out assembly and or maintenance operations without taking all precautions as indicated in the different sections or without the necessary specialization This manual must always accompany the equipment therefore it must be available and readable at any moment if necessary Also in case of sale rent change of place and or ownership these documents shall be enclosed with the relative equipment ADVICES FOR A CORRECT INSTALLATION This equipment is destined to an exclusively Professional use 1 Make sure that all the fastening parts of the spotlight are in good condition Regulate the proportions of the fastening acces sories screws bushes nuts supports etc in order to be slightly over dimensioned as compared to the actual requirements 2 Carefully check the contents of the pack
7. a specific component of the mechanical unit This includes the motors and the sensors of the various effects wheels color gobos prisms shutter etc WARNING An improper use of this documentation made by not specifically qualified staff can damage irremediably the electronic and or mechanical components of the projector i a 7 ion pa ll eis Y a He sh the ide sh BALE Fors i T So 2s 2 h E ZETT Eom e e eee eee i BEER e e e o M 2 4 j k HHHH Heri a hy 4 F E EE E EE T T E a M EEE Eee EE 1 Empty 15 Sensor PAN 2 Motor COLOR wheel 16 Sensor TILT 3 Motor BEAM SHAPING 17 S1 Sensor COLOR wheel 4 Motor FROST 18 S2 Sensor BEAM SHAPING 5 Empty 19 Empty 6 Motor CYANO 20 ON OFF Lamp only Magnetic Ballast version 7 Motor MAGENTA 21 Electronic Ballast connector 8 Motor YELLOW 22 LIGHT Sensor 9 Motor SHUTTER 1 23 POWER connector 10 Motor SHUTTER 2 24 Faston GROUND connection 11 Motor TILT 25 DMX INPUT 12 Motor PAN 26 HEAD FAN 13 Encoder TILT 27 BASE FAN 14 Encoder PAN 23 Power connector on board 1 2 12V 5 Blue 3 4 27V 5 Grey 5 6 27V 5 Black Pag 14 http www coef it info coef it 10 0 TROUBLESHOOTING The projector swiches on but t doesn t answer to commands Defecting projection N hl Projection with halo The lamp is not working The thermal
8. aging and the completeness of the components If any of the parts listed hereunder is missing please contact your Dealer immediately 3 Do not install the projector outside where the influence of atmospheric factors could damage the unit working rain wind intense heat etc or indoor if there is a high percentage of humidity 4 Do not clean the projector using water jets or immersion in different liquids Scrupulously follow the indications given in the chapter MAINTENANCE 5 Make the electric connections and the installation replacement of the lamp after having disconnected the power supply and after haved positioned the power switch to OFF The apparatus is classified as belonging to Class 1 type of protection against elec tric shocks Its connection to an earthed mains unit is compulsory The equipment must be protect by an adeguated magneto thermal switch You are recommended to equip the system with aptly dimensioned differential switches 6 Do not touch in any case the internal and external parts of the projector without previous authorization of the constructor and make modifications only by the intervention of qualified staff 7 Make sure that the projector is correctly fixed on the support as indicated in par 3 3 8 If the bulb explodes the particular design of the apparatus prevents the splinters from going outside the projector All the parts therefore shall be complete and perfectly assembled The lenses if visibly damaged sha
9. der to guarantee a necessary security and in respect of the actual safety rules concerning the projectors installation it is compulsory to install a sa fety chain equipped with two snaps provided with the projector to con nect the MP700 Wash s body to the fixing structure ATTENTION the safety chain equipped with two snaps which can be hooked to the two pivots placed under the base of the MP700 Wash see part A must be properly installed and fixed to the supporting structure in a way that an incidental givin in of the main bracket would leed to the short est possible fall of the projector After such an intervention the safety chain must be replaced with another original part ATTENTION COEF is not responsible for installations not correctly made or made without respecting the above indications those installations are considered dangerous Pag 6 http www coef it info coef it 4 0 POWER SUPPLY CONNECTIONS WARNING In order to guarantee the utmost safety connect the apparatus only to a properly earthed mains system The projector is designed to work at the tension and frequency indicated by the electrical data la bel on the rear Before connecting the projector to the mains a qualified electrician must check its conformity The projector must be protect by an adeguated magneto thermal switch Don t power the unit with a dimmer circuit Power indicated in the serigraphy table tollerance 5 10
10. eset of the projector is needed If this function is not cor rectly executed it will totally compromise the regular working of the projector at least for the group referred to the sensor itself The sensors of the encoders concerning the PAN and TILT movements are located in the base and in the arm of the MP700 Wash respectively The pictures clearly show how you can reach these components and where you can correctly operate for their maintenance Another place where grease and dust settle is inside the lamp box Carry out the following operations in order to clean unscrew but not completely the 4 screws on the side of the fin unit located on top of the bulb draw out the full fin unit clean the antiheat filter and the parabola of the bulb assemble the fin unit again by inserting first the part next to the lamp board and then the 4 screws in their seat tighten carefully http www coef net info coef it Pag 13 9 2 ELETTRONIC MAINTENANCE WARNING switch off the projector before operatinc This section is dedicated in detail to the electronic connections between the card and the mecha nical components assembled in the projector These informations will be absolutely necessary when the mechanical unit has to be removed from the projector for maintenance and or repair The connections are made using handy connectors and are detailed in figure where you can find indications about the connection between a specific connector and
11. ex antialo lens e CMY colour mixing system e RGB basic colour system e 3200 and 5600 K conversion filters Linear dimmer from 0 to 100 e Adjustable strobe e Rainbow effect adjustable in speed deer e Linear frost effect from 12 to 28 power SUPPI I ADSOrREd Powe e Rotating and indexable beam shaping e Mechanic shutter e Multifunction display V Hz Ballasttype 1 W e Internal power factor correction 100 60 Electronic 10 A 1000 e DMX 512 standard jli i i 120 60 Electronic 81A 970 e Remote On Off lamp via DMX TEHE e Remote reset via DMX 208 50 60 Electronic 45A 940 e Software upgrade via DMX with UNI PROG 8 Accessory 208 60 Magnetic 42A 840 e Automatic ventilation adjustment with internal temperature survey 230 50 60 Electronic 4 1A O40 Ge e T 230 50 Magoo 421A 870 e Automatic fault survey 230 60 magnetic 4A 840 16 control channels 250 50 60 Electronic 3 7 A 920 e Weight 37 5 Kg with electronic Ballast 28 5 Kg Pag 4 http www coef it info coef it 3 0 INSTALLATION The constructor is not be considered responsible in case of e Improper use fo the unit or use by not trained staff e Use in contrast with the directions on work safety e Wrong installation e Defective power supply e Serious lacks in the necessary maintenance e Unauthorized modifications and interventions e Use of spare parts that are not original or not specific for the unit e Total or partial inob
12. function and press again to go back to the starting level Example We installed our projector on the ceiling and for this reason we want the visualization of the display to be correct Press MENU Press H UP 14 times up to MISC Press ENTER the Display will show RSET Press H UP twice up to DSPL Press ENTER the Display will show ONOF Press H UP once up to STRV Press ENTER the Display will show STND this is the actual configuration state Press H UP once up to R E V the blinking point indicate the available configuration Press ENTER The Display visualization as been rotated to 180 Press MENU 3 times to return to starting MENU The indication of the display will automatically come back after 120 sec and inform on the set starting channel DMX If we are now in a sub function this automatic device will not assume control Pag 8 http www coef it info coef it 6 0 MENU FUNCTION amp SUB FUNCTIONS default_value factory assigned DMX Start channel SHOW KH H Lamp working hours KH thousands H hours RST GO Lamp working hours reset confirm by ENTER SHOW KH H Projector working hours KH thousands H hours No error EEPROM failure Malfunction of the COLOR motor sensor Malfunction of the PAN motor sensor Malfunction of the TILT motor sensor Malfunction of the BEAM SHAPING motor sensor No ignition of the lamp beyond 3 attempts break Malfunct
13. ghts from and to the manufacturer for repairs under guarantee are at Customer s charge e When applying for the repair always mention the serial number and the model of the equipment PACKING CONTENTS Carefully check the contents of the packaging and the completeness of the components If any of the parts listed hereunder is missing please contact your Dealer immediately e MP700 Wash complet unit e This user manual 2 quick lock release omega brackets 1 connector XLR 3 pin male 1 connector XLR 3 pin female 1 connector POWER 1 safety chain equipped with two snaps PROTECT NATURE DO NOT DISPOSE OF THE PACKAGING IN THE ENVIRONMENT CAREFULLY KEEP THE BOX AND THE COMPONENTS OF THE PACKAGING FOR ANY DISPLACEMENT OR RE SHIPMENT OF THE EQUIPMENT Do not leave the packaging elements polystyrene nylon metal parts etc unattended http www coef net info coef it Pag 3 1 0 DIMENSIONS amp POSITIONING i m bl a a Assembly ta ground Montaggio a terra Assembly to ceiling Montaggio a soffitto i sed i Aasrormily to wall Montaggic a parete F 2 0 TECHNICAL NOTES MP700 Wash DV with Magnetic Ballast Code 02E012 MP700 Wash DVP with Electronic Ballast Code 02E013 e Lamp MSR 700 SA 700W 54 000 lumen e 16 bit movement resolution PAN 540 TILT 270 with automatic repositioning e Silent movement e Silent operating mode only DVP e Dichroic glass reflector and pebble conv
14. ion encoder PAN Malfunction encoder TILT Checksum Setup not valid Lamp working hours for more than 500 hours LAMP start beyond 1 attempts attempt to warmth or exausted lamp LAMP off in not standard mode HOME SHUTTER TEST SHUTTER Fine regulation of the closing shutter Reserved HOME COLOR TEST COLOR OFF ON Color change in black out position P1 Fine regulation of the COLOR position HOME CYANO color TEST CYANO color Fine regulation of the CYANO position Reserved HOME MAGENTA color TEST MEGENTA color Fine regulation of the MAGENTA position Reserved HOME YELLOW color TEST YELLOW color Fine regulation of the YELLOW position Reserved HOME BEAM SHAPING Filter TEST BEAM SHAPING Filter Fine regulation of the BEAM SHAPING position HOME FROST Filter TEST FROST Filter Fine regulation of the FROST filter Reserved HOME PAN movement TEST PAN movement STND REV Switch movement direction DX SX ON OFF ON OFF the automatic repositioning of the PAN HOME TILT movement TEST TILT movement STND REV Switch movement direction UP DOWN ON OFF ON OFF the automatic repositioning of the TILT SCH CH1 CH16 DMX value for the indicated channel LAMP ONOF ON OFF AUTO Lamp ON Lamp OFF LAMP OFF after 1 hour of no change on DMX CDMX NO YES LAMP switching o
15. le 6 0 On switching the projector on the display will indicate the type of projector and the version of control software which have been installed To this purpose please remember that this type of projector belongs to a new generation of projectors designed with the possibility of updating the software version through the normal DMX connection by means of a programmer deliberately created UNI PROG 8 After the indication MSTR HOME the projector carries out the RESET and gets ready to be controlled from the connected console The display will indicate 1 as default value This means that the first channel occupied by the projector will re spond to the values sent to channel 1 by the DMX line This enables us to make MP700 Wash which we are instal ling completely independent from control or integral with any other installed projector General Rules Refer to the Table of Section 6 0 in the following page By each pressure Button MENU E permits to go backwards by one level G and H DOWN and UP buttons select functions and sub functions Button F ENTER enters the function and confirms a control By pressing Button MENU E and buttons UP and DOWN H and G you can select the menu you have to mo dify Once the wished menu is reached press Button F ENTER to confirm your selection and enter the function Press G or H to enter the sub functions if available Always confirm your selection with ENTER Press MENU to go out of the
16. ll be replaced by original spare parts 9 Minimum distance from illuminated objects The projector must be positioned in such a way that objects struck by the light beam are located at least 2 metres from the projector objective 10 Minimum distance from inflammable materials 0 3 meters 11 MAX ambient temperature 40 C 12 MAX external surface temperature 90 C 13 Don t look directly the lamp trough the lens 14 We recommend not to look at the lamp without wearing a proper protection also ensure that the covers are assembled to the equipment 15 Inside the equipment there are high temperatures and tension current values which might be very dangerous It is necessary to disconnect the equipment from the mains before removing its protection covers and wait for 30 minutes at least before touching any part inside 16 Do not switch on the equipment if its lamp is not inserted 17 Leave sockets and air outlets free from encumbrances and clean them periodically see Maintenance section 18 Do not leave the packaging elements polystyrene nylon metal parts etc unattended Pag 2 http www coef it info coef it This manual has been organized in order support the user the installer or the maintenance operator of the de scribed unit with those necessary informations for a correct use of the installation and working procedures of the same unit The various procedures will be just signalled by indicators when necessary
17. lor is full inserted YELLOW COLOR 0 5 Neutral 6 250 insert YELLOW color 251 255 YELLOW color is full inserted PAN MOVEMENT PAN MOVEMENT FINE ADJUSTMENT TILT MOVEMENT TILT MOVEMENT FINE ADJUSTMENT COLOR WHEEL RGB BASE COLOR CONVERSION WOOD 0 5 Neutral 6 35 BLU 36 65 RED 66 95 GREEN 96 125 Wood 126 155 Color filter conversion 5600 K 156 185 Color filter conversion 3200 K 186 195 Random full color slow 7 steps 196 205 Random full color fast 7 steps 206 230 CW rotation adjustment 231 255 CCW rotation adjustment COLORS PRE SETTINGS 0 15 WHITE NEUTRAL 16 30 YELLOW COLOR 1 31 45 GREEN COLOR 2 46 60 ORANGE COLOR 3 61 75 PINK COLOR 4 76 90 CYANO COLOR 5 91 105 PURPLE COLOR 6 106 120 RED COLOR 7 121 135 BLUE COLOR 8 136 150 GREEN WATER COLOR 9 151 165 YELLOW LIGHT COLOR 10 166 180 GREEN LIGHT COLOR 11 181 195 ORANGE LIGHT COLOR 12 196 210 PINK LIGHT COLOR 13 211 225 CYANO LIGHT COLOR 14 226 240 GREEN VERY LIGHT COLOR 15 241 245 FAST COLORS MIXING 246 250 MIDDLE COLORS MIXING 251 255 SLOW COLORS MIXING http www coef it info coef it Pag 10 CANALE BEAM SHAPING FILTER 0 5 Neutral 6 210 Positioning 11 211 225 vertical orizzontal vertical slow 226 240 vertical orizzontal vertical middle 241 255 _ vertical orizzontal vertical fast FROST 0 5 Neutral 6 130 Regulation insertion FROST effect 131 140 FROST inserted 141 155 from FROST 100 to FR
18. n tenance Technical aid is required Set ON ENCO Function of PAN TILT con figuration menu cap 6 0 Pag 15
19. n by DMX control MASTER HOME Starting RESET YES NO MASTER HOME via DMX control ON OFF Display on Display off STND SWAP Channel control switch PAN TILT YES NO automatic value YES Electronic Dimmer ON Show the installed software version STND REV 180 rotation of the visualization display E http www coef net info coef it Pag 9 CANALE 10 7 0 CANALI E VALORI DIGITALI SHUTTER STROBE DIMMER 0 5 SHUTTER closed no Dimmer 6 100 DIMMER from channel 13 value 101 110 DIMMER O gt 100 Automatic 6 sec 111 120 DIMMER 100 gt 0 Automatic 6 sec 121 126 DIMMER 0 gt 100 slow Faster shut down 127 132 DIMMER 0 gt 100 middle Faster shut down 133 138 DIMMER 0 gt 100 fast Faster shut down 139 144 DIMMER 100 gt 0 slow Faster open 145 150 DIMMER 100 gt 0 middle Faster open 151 156 DIMMER 100 gt 0 fast Faster open 157 162 DIMMER 0 gt 100 gt 0 slow 163 168 DIMMER 0 gt 100 gt 0 middle 169 174 DIMMER O gt 100 gt 0 fast 175 180 Strobe lamp from 1 to 6 random reg 0 0 0 5 sec 181 186 Strobe lamp from 1 to 6 random reg 0 6 1 5 sec 187 192 Strobe lamp from 1 to 6 random reg 1 6 2 5 sec 193 250 STROBE Speed adjustment 251 255 SHUTTER open no Dimmer CYANO COLOR 0 5 Neutral 6 250 insert CYANO color 251 255 CYANO color is full inserted MAGENTA COLOR 0 5 Neutral 6 250 insert MAGENTA color 251 255 MAGENTA co
20. servance of instructions e Unusual events 3 1 LAMP MOUNTING OR REPLACING WARNING read carefully e Switch off the projector before operating The lamp used in the fixture is a high pressure lamp and must be handled very carefully e The unit is realized to use only MSR700 lamp absolutely don t use other types of lamp The lamp must be changed if damaged or deformed by heat e Wait at least 15 minutes after the projector has been switched off before operating again in order to let it cool down and avoid the lamp explosion e Wear protection gloves and glasses e Read carefully the lamp builder s instructions e Dont look directly the lamp PEE yy Wait 30 minutes in order to avoid burns Unscrew with a cross screwdriver the first screw A for a single turn unscrew the second one completely B unscrew completely the screw A and to remove the cover that supports the lampholder Insert delicately the lamp in the projector support driving it with the round cover Pay attention the lampholder s wires must correctly reenter in the projector Block the cover screwing the screws up part A B http www coef net info coef it Pag 5 3 2 OPERATING VOLTAGE WARNING unplug the fixture from the power supply before operating The operation must be performed only by highly specialized staff WARNING The wrong selections of the operating tension and or frequency compromise the good operation of the fixture and
21. switch is active Wrong DMX configuration Defective cables LED A is off Defective control unit The lens is broken Dust or grease stored on the all parts of projector Dust or grease stored on the all parts of projector ACTION Check if the luminous indicator is lighted or not Replace the lamp Just to wait for little of time Make sure that the projector is correctly configurated Replace or repair the DMX cable Check the control unit amp DMX cable Check the control unit by means of other working projectors Technical aid is required Check that the lens are not broken Remove dust or grease stored on lenses Carefully clean the optical group lenses and the projector components see Main tenance chapter Rp PAN or TILT movement doesn t coincide to the selcted alue PAN or TILT movements The projector does not carry out N he automatic repositioning of the N ie color or other effects doesn t Position sensor dirty with dust or coincide to the selected value grease Defective motor Electronic board Defective motor Electronic board ENCO off in the PAN TILT confi guration menu cap 6 0 http www coef net info coef it Carefully clean the optical group lenses and the projector components see Main tenance Technical aid is required Carefully clean the optical group lenses and the projector components see Mai
Download Pdf Manuals
Related Search