EDW-680T-UG - EddyWireless
Contents
1. card identification function EDW 680T can work with RFID reader to detect the RFID tag The tag info will be compared with card database info Once the current RFID tag can match the tag info in database it will control the relay to turn on the car If the current RFID tag cannot match the tag info in database it will control the relay to turn off the car For more about how EDW 680T work with RFID reader please refer to document named how EDW 680T work with RFID reader 4 5 CCD camera picture taken function The EDW 680T can work with CCD camera to get the picture info The picture info will be send from tracker to server And then the picture will be shown on server real time For more about how EDW 680T work with RFID reader please refer to document named how EDW 680T work with CCD camera 4 6 Vehicle control function The multi analog digital output of EDW 680T make the device can control the vehicle such as shutdown engine close window and close door Please don t use that function when the vehicle is in high speed Following picture shows how EDW 680T work with relay 16 www eddywireless com to control vehicle 4 8 4 9 Relay white cable Red Cable ACC Relay Green Cable Relay Green Cable Yellow Cable FaX ON OUT1 2 3 Cut the power cable to the ignition relay Car battery Tank fuel detector function Connected with external tank fuel level sensor2. country code and district code W000000 524 52 district Parameter county code and district code number when send feedback 29 www eddywireless com sms Extend W 008 ABCDEFG W000000 008 1000100 Settings Parameter ABCDEFG A 0 turn off the function of sending an SMS location report to the authorized phone number when it makes a call to EDW 680T A 1 turn on the function of sending an SMS location report to the authorized phone number when it makes a call to EDW 680T B 0 location data of NMEA 0183 GPRMC will be interpreted into normal text for easy reading For example Longitude 114 degree 04 cent 57 74 second Latitude 22 degree 32 cent 40 05 second location data complies with NMEA 0183 GPRMC protocol For example GPRMC 072414 000 V 3114 3763 N 12131 3255 E 0 00 0 00 050805 00 C O turn off the function to automatically hang up an incoming call C 1 turn on the function to automatically hang up an incoming call after 4 5 rings D 0 Turn off the function of sending an SMS when EDW 680T is turned on D 1 Turn on the function of sending an SMS to SOS number when EDW 680T is turned on E 0 reserved E 1 EDW 680T shuts down automatically when the powervoltage lower than 3V F 0 Turn off the alert when EDW 680T enters GPS blind area F 1 Turn on the alert when EDW 680T enters GPS blind area SMS is to be sent to SOS number G 0 LED light works normally G
3. for multi function connector The optional accessory including relay Mobile data terminal CCD camera RFID reader temperature sensor tank fuel level sensor SD card printer OBD bridge CAN bridge Bluetooth kit For more details about optional accessory please refer to Redview GPS AVL Accessory Guide 11 www eddywireless com 3 Specification 3 1 Software Features Tracking via SMS or GPRS TCP UDP Ouad band GSM module GSM GPS integrated Support CAN OBD bridge Bus Support printer With 4 serial RS232 port 2 analog port 4 digital input and 4 digital output Input pulse count taxi meter count Can work with camera to take picture Can work with RFID to identify driver Can work with mobile data terminal for text display Can work with SD card to store journey info Can work with Bluetooth to transfer data wireless Build in 3 axis sensor Build in flash Build in battery 3 2 Hardware Features GSM GPRS core Simcom SIM340D 850 900 1680 1900MHz GSM GPRS services Data SMS GPRS class B class 10 TCP UDP IP Physical characteristics Dimensions L W H 85mm 120mm 30mm Weight approx 200g including build in battery Temperature range Operation 20 Celsius degree to 80 Celsius degree Power sources Input voltage 10 32 Volt DC regulated Max 2A Rechargeable Li ion battery 850mAh 12 www eddywireless com Antenna GSM GPRS antenna GPS antenna Indication 3 LED indicator for GSM GPRS GPS statu
4. operator lists the module will choose the one which match the profile and with strongest GSM signal as example below shows 21 www eddywireless com Profile 0 Profile 1 Profile 2 Operator code Operator Operator 26000 code 26001 code 26002 APN CMNET APN CTNET APN PCCW Example Profile switching Current operators 26000 with GSM signal strength 29 26001 with GSM signal strength 18 26002 with GSM signal strength 17 26004 with GSM signal strength 11 Profile s operator search procedures Operator code founded in profile 0 1 2 Compare GSM signal strength of APNs in profileO profilel profile2 choose the strongest one Profile switch Profile 0 Each 5 mins operator scan procedure You may configure the profile list by SMS command For more please refer part 7 SMS command list 22 www eddywireless com 5 Get start EDW 680T will only accept commands from a user with the correct password Commands with wrong password are ignored The default password is 000000 5 1 Device installation 5 1 1 Connect the external GSM antenna and GPS antenna 5 1 2 Open the SIM card slot and then insert SIM card Uu Ki With SIM card inside 5 1 3 Turn on the device 23 www eddywireless com 5 1 4 Connect the device and the vehicle via the cables The Power and GND of the EDW 680T should be connected to the vehicle If these signals are not connected
5. to the vehicle please use power supply or 12 24V battery 5 2 Basic SMS Commands 5 2 1 Position Report To know the location of your EDW 680T send an SMS or make a telephone call directly to EDW 680T and it will report its location by SMS Command W lt password gt lt 000 gt Notes The default password is 000000 Example SMS sent W000000 000 SMS received Latitude 22 32 36 63N Longitude 114 04 57 37E Speed 2 6854Km h 2008 12 24 01 50 To get EDW 680T s position by another easier way a Call EDW 680T using your mobile phone b After listening to the ring for 10 20 seconds hang up the phone c Then after 20 second your mobile phone will receive a position SMS 24 www eddywireless com 5 2 2 Set Interval for Automatic Timed Report Description Automatic timed reports will be sent to your mobile phone according to the time interval you set Command W lt password gt 002 XXX Notes XXX is the interval in minute If XXX 000 it will stop tracking Example SMS sent W000000 002 005 SMS received Set Timer Ok 005 EDW 680T will then report its location by SMS every 5 minutes 5 2 3 Stop Automatic Timed Report Description Automatic timed reports will stop once EDW 680T receives stop command Command W lt password gt 002 000 Example SMS sent W000000 002 000 SMS received Set Timer Ok 000 EDW 680T will stop automatic timed report For more detailed SMS commands please go to
6. 1 LED light stops flashing when EDW 680T working is the ending character default value is ABCDEFG 1000100 B 1 Output control W 020 port No switch Parameter Port No 1 Out put 1 2 Output2 3 Output3 4 Output4 5 Output5 Switch 0 to close the output 1 to open the output WO00000 020 1 1 Delete all info store in flash W 503 Enable disable motion sensor W 722 switch Parameter switch 0 enable default 1 disable W000000 722 1 Set degree of W 036 Degree W00000 036 090 direct change Parameter degree from 30 270 degree tracking Set the text in W 033 1 text W000000 033 1 help me SOS alarm Parameter text no more than 8 characters SMS Set current W 612 telephone number as the number to receive sos alarm Set W 431 sensitivity WO000000 431 1 The sensitivity of microphone Parameter sensitivity 1 4 1 mini sensible 4 max sensible 30 www eddywireless com Enable disable voice W 210 switch Parameter switch 0 disable voice wiretapping wiretapping 1 enable voice wiretapping Set threshold W 026 threshold W000000 026 20 of entering Parameter threshold when the device keep in park mode for more than sleep mode preset threshold mins enter sleep mode In sleep mode the GPS module will be turn off to save power 00 99 00 disable s
7. Chapter 7 SMS Command List 5 3 GPRS Settings by SMS Tracking via GPRS you should set IP Port and APN for EDW 680T Ensure that your SIM card in EDW 680T supports GPRS connection prior to setting 5 3 1 Set ID for EDW 680T Command W lt password gt 010 ID Note Tracker ID must not over 14 digits Example W000000 010 123456789 EDW 680T will then reply with an SMS Set SIM Ok 123456789 to confirm this setting 5 3 2 Set APN 25 www eddywireless com Command W lt password gt 011 APN APN Name APN Password Note If no APN name and password reguired input APN only Example W000000 011 CMNET EDW 680T will reply with an SMS like Set APN OK CMNET to confirm this settin g 5 3 3 Set IP Address and Port Command W lt password gt 012 IP PORT Example W000000 012 202 116 11 12 6800 EDW 680T will then reply an SMS Set IP Ok 202 116 11 12 6800 to confirm this setting 5 3 4 Set Time Interval for Sending GPRS Packet Command W lt password gt 014 time interval in unit of 10 seconds MOVE Mode vibration Example W000000 014 00003 EDW 680T will send GPRS packet every 30 seconds in Move mode vibration Command W lt password gt 114 time interval in unit of 10 seconds PARK Mode No vibration Example W000000 114 00012 EDW 680T will send GPRS packet every 120 seconds in Park mode no vibration W000000 014 00000 is STOP GPRS For more information regarding of bulk configurati
8. EDW 680T can detect the fuel level of tank and send it to control center via GPRS For more info about this function please refer to document how to use tank fuel level sensor Temperature detector function Connected with external temperature sensor EDW 680T can detect the temperature and send it to control center via GPRS For more info about this function please refer to document how to use temperature sensor 4 10 Pulse counter meter calculate function EDW 680T can work with vehicle s meter and calculate the 17 4 11 www eddywireless com mileage according to pulse number and send it to server For more about this function please refer to document HoEDW 680Twork with vehicle s meter to calculate mileage User can also reset the mileage function by SMS For more info about how to reset the mileage report please refer to sms command list part of this document Intelligent tracking method EDW 680T can detect direction change EDW 680T can send position data when the heading difference between two consecutive positions changed by a value larger than the configured value In this way the EDW 680T can produce very good trace accuracy The above picture shows that the EDW 680T will send position info when direction change To minimize the traffic cost user can preset the degree of direction change For more info about how to preset the value please refer to the SMS command list at the
9. Set parameter W 662 pulse number in 1 kilometer W000000 662 00400 for speed Parameter pulse number in 1 kilometer 0 99999 sensor Enable OBD W 050 switch W000000 050 1 diagnostic Parameter switch 0 disable OBD diagnostic 1 enable OBD diagnostic Alerts Configuration Description Command parameter and return Example Set W 004 threshold W000000 004 1 threshold of Parameter threshold when internal battery s voltage is lower low power than threshold will send low power alert by both alert SMS and GPRS Threshold 0 disable this feature default 1 send alert when battery voltage lower than 3 3V 2 send alert when battery voltage lower than 3 4V 31 www eddywireless com 3 send alert when battery voltage lower than 3 5V 4 send alert when battery voltage lower than 3 6V 5 send alert when battery voltage lower than 3 7V Set W 005 threshold W000000 005 08 threshold of Parameter threshold when the vehicle speed higher than Explain The threshold of over overspeed threshold the device will send over speed alert by speed alert is 80km h alert SMS and GPRS The alert will be stored in SD card also Threshold 00 disable this feature default 01 20 the threshold is in unit of 10km h Set geo W 006 radium of geo fence alert fence alert Parameter radium of fence the point is current position Radium of geo fence alert 00 disab
10. age Replace SIM card if needed Remove PIN code by inserting SIM in you phone and deleting the code Inspect SIM clean the contacts If re inserting does not help try another to see if it will work If you are in a different country 27 www eddywireless com your SIM account must have roaming enabled Problem SMS received starts with Last Possible Cause Resolution Unit does not have clear view of the Move the antenna of the unit to a sky location where the sky is visible EDW 680T is in an inner place Wait for the target to come out Battery is low Recharge the unit and the GPS will start working 7 SMS Command List Remarks is user s password and the default password is 000000 Network communication Configuration Description Command parameter and return Example SetlD W 010 ID W000000 010 123456789 Parameter ID must not over 14 digitals Return Set SIM OK ID Set APN W 011 APN APNName APN Password WOoo00000 011 CMNET Parameter APN please contact SIM card supply for APN The default APN is CMNET APN Name if no APN name just leave empty APN password if no APN password just leave empty The total length of APN APN name and APN password is not over 54 characters Return Set APN OK APN APN name APN password Set IP and W 012 IP Port W000000 012 202 116 11 12 6800 port Parameter IP xxx xXX XXX XXX Port 1 65534 Return Set IP OK IP por
11. ark device is in off status SIM card slot Open the slot to place SIM card Multi functional port Please refer following table for more info about this port Multi functional port Pin Description Number 1 black amp red Digital input 1 in cable cable socket of EDW 680T already connectto SOS input 2 Blue Digital input2 cable 3 gray Digital input 3 cable 4 Purple Digital input 4 cable 5 Black GND cable 6 yellow Analog input 1 cable 7 White Analog input 2 cable 8 Red Power 8V 32V cable 9 Green Digital outputl cable 10 red amp Digital output2 orange cable 11 brown Digital output3 cable 12 Orange Digital output4 cable Remark Digital input 1 Digital input2 Digital input 3 is negative trigger www eddywireless com Digital input 4 is positive trigger in which input4 is usually to connect with ignition or taxi meter for pulse counter 2 3 Back panel Following is picture of back panel LED for SD carde lt o ean ge ee nee ee SD card slote ON OFF switche Name Remarks LED for SD card SD card led working with following 3 status Keep lighting no read write SD card Blinking read write SD card Dark no SD card in SD card slot 10 www eddywireless com 2 8 Package contents The basic package is including EDW 680T GPS antenna GSM GPRS antenna cables
12. end of this user manual 18 www eddywireless com 4 12 Moving and Park working method 4 13 4 14 EDW 680T can detect the moving and parking method The park mode means the vehicle is not move and the engine is off The moving mode means the vehicle is moving or the engine is on When in park mode it will send the GPRS package in default time interval of 5 minutes When in moving mode EDW 680T will send the GPRS package in default time interval of 30 seconds The time interval of park and moving mode can be preset by user For more info about how to set time interval please refer the 5 3 4 part of this document Hand free voice communication EDW 680T can work with external hand free voice communication to making call and receiving call Once the buzz ring the user can receive call by press SOS button User can make call to preset telephone number by press SOS button Audio broadcast With external audio decoder and amplify EDW 680T can broadcast audio message to reminder driver passenger Customer can configure the trigger condition of audio message and the content of audio message This is widely used in bus tracking for stop reminder and taxi tracking for passenger reminder For more about this feature please refer how EDW 680T work with audio broadcast feature 4 15 Printer EDW 680T is a GPS tracker can work with SD card and printer to record sending and print dangerous driving behavior includi
13. f vehicle parts using 2A fuse for example the vehicle battery And also the SIM card capable of GSM GPRS should be inserted before connect with power After completing the connection the user should change the configuration for its network operator and user s environment EDW 680T receives GPS data via GPS antenna after fixing GPS signal And then the device sends the location data to control center according to its configuration which is able to be set by control center or user s SIM 4 1 Communication function EDW 680T is able to be communicated by GSM and GPRS network using SMS and GPRS packet The device can support both GSM and GPRS network but the control center software is able to be distinguished by the application of SMS and IP packet Following communication mode is supported SMS only mode When the control center does not have internet connection it can be communicated with the device via SMS To conduct it the control center should connect with GSM modem GPRS only mode When the control center have internet connection the device is communicated with the control center via GPRS packet at time interval The time interval can be preset by customer thru GPRS SMS UART configuration cable 14 www eddywireless com SMS and GPRS mode When the control center connect with GSM modem and internet the control center communicates with the device through both GPRS packet and SMS at time interval The t
14. ime interval can be preset by customer thru GPRS SMS UART config cable 4 2 Alarm function EDW 680T send alarm SMS GPRS package to the predefined SMS number IP address The alarm package is able to be activated for following functions 4 3 Journey start end alarm Over speed alarm Panic alarm Towing alarm Geo fence alarm Over time driving alarm Alarm which can preset by customer such as over temperature alarm Crash alarm Data logging and forward function EDW 680T can work with 2 ways to data logging and forward By flash When enter GPRS blind area the position info data from external sensor can be stored in flash and forwarded when GPRS re establish By SD card The journey info the picture info the status info from CAN bus the driver s info can be stored in SD card and can be get by GPRS by Com port Following info can be stored in SD card Driver s name Driver s company Driver s license code Vehicle s license plate number Vehicle ID info 15 www eddywireless com Vehicle s position speed direction in each second Vehicle s mileage Time point when engine start Time point when engine stop Times which driver over speed driving Times which driver over time working Times which open the car door Times which stop the car door Picture taken from camera Info from OBD bridge For more about how EDW 680T store data in SD card please refer How EDW 680T work with SD card 4 4 RFID
15. ion The driver can also reply the host server via text communication and voice communication Anti GSM Jamming When the EDW 680T detect GSM signal jammed it will store the 20 4 21 www eddywireless com all info in internal flash At the same time the internal buzz will be triggered and keep trigger until GSM signal recover The internal buzzer can stop when receive SMS command of stop buzzer or GSM signal recover For more about the stop buzzer SMS please refer to Chapter 7 SMS command list Roaming EDW 680T has 10 profiles saved in Flash memory of the module Each profile has a list of parameters which enables EDW 680T to operate in different modes using different profiles You are allowed to setup up to 10 different profiles Global parameters contain settings that are common for all 10 profiles This means that if you set EDW 680T to call to predefined number you will be able to call it using any profile Basic scheme of global parameters and profiles is shown below Switching between profiles can be performed by profile switch depending on GSM operator code Global parameters Profile 0 Profile 1 Profile 2 Profile 9 Parameters Parameters Parameters APN APN APN Operator code Operator code Operator code Parameters APN Operator code Profile Switch depending on GSM operator code and signal strength Profile switching is mostly used in roaming applications to save communication cost In the current
16. le 01 30m 02 50m 03 100m 04 200m 05 300m 06 500m 07 1000m 08 2000m Set W 041 threshold threshold for Parameter threshold O Close motion alarm motion 1 in 30s the vibration duration alarm 0 1s 2 in the 30s the vibration duration is 1s 3 in the 30s the vibration duration is 10s When the threshold is set to 2 and keep vibrating for 2s in unit of 30s the device will send motion alarm by SMS and GPRS Enable buzz W 042 switch when GSM Parameter switch 1 enable buzz default anti 0 disable buzz jamming In anti jamming mode when enable buzz command is set the alarm buzz will keep output until GSM signal recover or receive disable buzz command Description Command parameter and return Example Configure w 563 X YYYYY CCCCCCCCCCC w000000 7 46000 cmnet profile parameter X profile No from O to 9 YYYYY operator code for more please refer http www imei info operator codes CCCCCCCC APN string Erase all w 544 w000000 544 profiles EDLY IRELESS o
17. leep mode set time W 760 guality picture time interval WO00000 760 1 012 interval of Paramter picture guality automatically picture taken and picture quality which stored in SD card 1 maxim level picture quality which is 640 480 2 middle level picture quality which is 320 240 3 minimum level picture quality which is 160 120 Time interval time interval of taking picture 5 999 in units of minutes mini time interval of taking picture is 5 mins 0 stop take picture automatically default value set time interval of sending picture and picture quality from tracker to server by GPRS W 762 picture quality time interval Parameters picture quality 1 maxim level picture quality which is 640 480 2 middle level picture quality which is 320 240 3 minimum level picture quality which is 160 120 time interval interval of taking picture and send picture to server via GPRS 10 999 in units of minutes mini time interval of taking picture is 5 mins 0 stop take picture automatically default value W000000 762 3 010 set end time of journey info stored in SD card after this SMS is send the data in 10 mins before this time will be print on paper W 536 MMDD HHMM parameters MM month DD date HH hour MM mins W000000 536 0618 1505 Enable pulse counter W 640 switch parameter switch 1 Enable Speed sensor 0 Disable speed sensor
18. meter Change W 001 New password W000000 001 123456 password Parameter new password which is 6 digital Position amp status amp version reporting Description Command parameter and return Example Get current W 000 W000000 000 position Set interval W 002 time interval WOoo0000 002 001 for Parameter time interval of automatic report by SMS in unit of automatic 1 min from 001 999 When time interval is timed report 000 will stop report position by SMS by SMS Get position W 100 with google map s linkage Get IMEI W 607 Get firmware W 600 version Application Configuration Description Command parameter and return Example Configure the W 003 switch 1 telephone number W000000 003 1 1 008675526030340 1 phone Parameter switch 0 disable the phone call feature number for Switch 1 enable the phone call feature when sos button is SOS button pressed will call preset telephone phone call Telephone number max 16 digitals Configure the W 103 telephone number W000000 103 008675526030442 2 phone Parameter telephone number max 16 digitals number for SOS phone call Add country code district code to received telephone number when SOS button is W 502 country code and district code XXX Parameter country code and district code WOo00000 502 8617F pressed Add country W 524
19. ng over speed driving over time driving harshing braking etc This is widely used in police enforcement 19 www eddywireless com 4 16 4 17 4 18 4 19 4 20 assistance For more info please refer document named how EDW 680T work with printer Read vehicle data from OBD bridge or CAN bridge EDW 680T GPS tracker can connect with external OBD bridge Or CAN bridge to read vehicle info The vehicle info include vehicle speed engine RPM vehicle distance fuel level axle weight trailer weight For more about which vehicle brand CAN bridge can work with please refer to program and function lists for CAN bus bridge For more about how EDW 680T GPS tracker work with CAN bus please refer user manual named how EDW 680T work with CAN bus Crash detection With build in 3 axis accelerator sensor EDW 680T can detect and record vehicle s crash fast stop and fast start in SD card The stored info can be also send via GPRS For more about this feature please refer how EDW 680T work with crash detection Bluetooth communication With optional Bluetooth kits EDW 680T can send info stored in SD card via Bluetooth For more about this feature please refer how EDW 680T work with Bluetooth Mobile data terminal interface With mobile data terminal 2 ways text communication between host server and driver is available The host server can also inform destination to driver and provide navigat
20. on by USB cable please refer to lt GPS Tracker Parameter Editor gt 5 4 How to use external sensor 5 4 1 Connect external sensor with EDW 680T 5 4 2 Control center send related command to tracker unit to set the parameter of using external sensor such as time interval of taking photo of CCD camera 5 4 3 Receiving GPRS package which include detection data 26 www eddywireless com For more info about how to use external sensor Please refer to Redview GTP GPRS communication Protocol for GPS Tracker 6 Troubleshooting Problem Unit will not turn on Possible Cause Wiring was not connected properly Battery needs charging Resolution Check and make sure wiring connection is in order Recharge battery Problem Unit will not respond to SMS Possible Cause GSM antenna was not installed properly GSM Network is slow Unit is sleeping Wrong password in your SMS or wrong SMS format The SIM in EDW 680T has run out of credit No SIM card SIM card has expired SIM has PIN code set SIM is warped or damaged Roaming not enabled Resolution Make EDW 680T connected to GSM network Wait for SMS Some GSM networks slow down during peak time or when they have eguipment problems Cancel sleeping mode Write correct password or SMS format Replace or top up the SIM card Insert working SIM card Check in phone that the SIM can send SMS message Check in phone that the SIM can send SMS mess
21. s SD card status 3 3 Technical specification GSM GPRS specification Freguency Simcom 340D Bands 850 900 1680 1900Mhz GSM class Small MS Transmit Class 4 2w at EGSM900 and GSM850 power Class 1 1W at DCS1680 and PCS 1900 GPRS GPRS multi slot class 10 connectivity GPRS mobile station class B Data GPRS Data up downlink transfer Max 85 6 42 8kbps Coding scheme cs 1 cs 2 cs 3 and cs 4 Supports the protocols PAP and CHAP commonly used for PPP connections Data CSD CSD transmission rates 2 4 4 8 9 6 14 4 kbps SMS SMS MT MO CB Text and PDU mode Support transmission of SMS alternatively over CSD or GPRS User can choose preferred mode TCP IP stack Internet services TCP UDP HTTP FTP SMTP POP3 FAX Group 3 Class 1 Class 2 SIM Supported SIM card 3V GPS module specification General Receive Freguency 1 57542Ghz 1 023Mhz GPS datum WGS 84 SIRF star III chipset Acquisition Rate Conventional mode Cold warm hot start lt 42 38 1 sec 95 typical Accuracy Position 10 meters CEP without SA 13 www eddywireless com Velcocity 0 1meters s without SA Time 1ms sync to GPS time Channel 24 channel GPS 4 Function EDW 680T is able to be powered from 8V to 32V DC The VIN GND and ignition line of the vehicle port should be connected with the vehicle to use car management The VIN line should be connected to 12V or 24V DC o
22. t Set Time W 014 Time interval W000000 014 00003 Interval for Parameter Time interval XXXXX should be in five digitals Sending XXXXX 00000 to close this GPRS Packet function in move XXXXX 00001 65535 time interval for Mode sending GPRS packet and in unit of 10 seconds Return Set TM OK Time interval Set Time W 114 Time interval W000000 114 00012 Interval for Parameter Time interval XXXXX should be in five digitals and Sending in unit of 10 seconds GPRS Packet XXXXX 00000 to close this function in park XXXXX 00001 65535 time interval for mode sending GPRS packet and in unit of 10 seconds Enable ping W 200 Switch W000000 200 1 Parameter Switch 0 disable ping command Switch 1 enable ping command default Set DNS W000000 012 DNS domain Port W000000 012 xy gicp net 8000 domain Parameter DNS domain max 16 characters Port 1 65534 28 www eddywireless com System Configuration Description Command parameter and return Example Change the W 040 Prefer Time zone W000000 040 08 time in all Parameter Prefer Time zone AXX which is time differ to SMS Greenwich Mean Time feedback A or XX 00 12 The default time zone in SMS is Greenwich Mean time Reboot the W 991 RESET device in 10 Return The device will reset in 10 mins mins Note _ The RESET should be in capital Restore all W 991 199147F4 default para
23. ver and map navigation Can work with hand free voice kits can be used for phone call or voice broadcast Can work with CAN bus bridge OBD bridge to read vehicle info including RPM fuel info axle weight etc Bluetooth kit Barcode reader www eddywireless com 2 1 EDW 680T unit EDW 680T is designed in a compact and simple rugged Aluminum enclosure At front panel there are 3 LED indicators shows the status of the unit And various ports for vehicle interface COM port SIM card slot SD card slot on both side of the device 2 2 Front panel Following picture shows the front panel Figure 3 Front panel H RS232 port connect to Multi functional port RS232 port connect to RFID reader Mobile data terminale RS232 port connect to CAN bus bridgeOBD bridge e Microphone for 2 ways voice communication USB port for configuration and upgrade for printer Bluetooth kitse Name Remarks GPS led GPS led work with 3 status In each 3s lighting for 2 9s and dark for 0 1s get www eddywireless com good GPS signal In each 3s lighting for 1 5s and dark for 1 5s no GPS signal In each 3s keep dark device is in off status GSM led GSM led work with following 3 status In each 3s lighting for 2 9s and dark for 0 1s get good GSM signal In each 3s lighting for 1 5s and dark for 1 5s no GSM signal In each 3s keep d
24. zA ELLY IRELESS c www eddywireless com EDW 680T CAN Vehicle Locator User Manual Version 2 6 d d ww e 4 DA Redview GPS www eddywireless com Contents Iss REPO UCHOD EE 2 EDW 680T Overview eeh ENN nn sD 3 PECCA ON NEG Ee A FUNCIO EEN Ds CS EE 6 Trouble SANOO eege 7 More SMS command ee IAR RR RR Do www eddywireless com l Introduction EDW 680T which come in a compact design is a powerful real time fleet management and vehicle tracking system using high sensitivity GPS and wireless GSM GPRS communication This self contained and autonomous tracking device including GSM module GPS receiver Li ion battery and Multi analog input is able to be used as observing the location of vehicle detecting temperature detecting fuel costing working camera to take picture working with RFID to identify driver work with SD card to store journey info working with printer to stored info on paper working with meter to counter pulse working with OBDII CAN bus to get vehicle status remotely Figure 1 EDW 680T appearance www eddywireless com 2 EDW 680T overview Ln 0 www eddywireless com Advanced feature of EDW 680T Can work with RFID reader and tag to identify driver Can work with camera to take picture Can work with SD card to store journey info Can work with printer to print info in SD card Can work with mobile data terminal to display text from ser
Download Pdf Manuals
Related Search