HCS544/HCS544X Day Night Camera Quick Install Guide
Contents
1. HCD544 HCD544X Camera Quick Install Guide Important Safety Instructions e Read and keep these instructions e Heed all warnings e Follow all instructions e Do not use this apparatus near water e Clean only with dry cloth e Do not block any ventilation openings Install in accordance with the manufacturer s instructions e Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat e Use only with the bracket or mounting system specified by the manufacturer or sold with the apparatus e Refer all servicing to qualified service personnel Installation The HCD544 Series camera is designed for general surveillance applications and is ideally suited for low light indoor environments Installing the Lens The HCD544 Series camera is factory configured for a CS mount lens Screw the lens customer supplied into the front of the camera body An IR corrected Day Night lens is recommended for this camera Figure 1 Lens Installation Setscrews x2 DC Lens Pin Definitions Pin Function 1 TRL 0o03 40 2 CTRL o o 3 DRV 12 4 DRV Connecting the Camera Note Check the power source from the external power supply before applying power to the camera 1 Connect the VIDEO connector on the rear of the2. LEVEL camera switches to night mode N gt D The light detection level 4 15 at which the LEVEL camera switches to day mode Set MODE to AUTO and D gt N LEVEL at least 3 less than N gt D LEVEL NIGHT Set the color mode in night mode COLOR B W Black white no color burst COLOR Color Set MODE to AUTO or ON 3 PRIVACY Masks an area of the screen from video monitoring _ lt lt PRIVACY gt gt N Menu Item Description CONTROL ON HSTART 100 CONTROL ON Hide an area of the scene from H END 130 V START 50 VIEWING ae _ HSTART Seta horizontal start position 0 187 H END Set a horizontal end position 0 187 V START Seta vertical start position O 122 V END Set a vertical end position 0 122 4 MIRROR Produces a horizontal mirror image on screen SHARPNESS Sharpens the image on screen image level O 15 Excessive sharpening may cause picture noise 6 FACTORY Restores all factory default settings DEFAULT 7 SWVERSION Displays the current firmware version RETURN Returns to the main SETUP menu SPECIAL Menu 1 On the SETUP menu press the UP or DOWN menu control and then select SPECIAL 2 Press ENTER to access the SPECIAL menu Figure 6 SPECIAL Menu Submenu Menu Options CAMERA D ON OFF DAY amp NIGHT AUTO ON OFF lt lt SPECIAL MENU gt gt LD 1 CAMERA ID ee 2 DAY amp NIGHT AUTO 3 PRIVACY ON PRIVACY ON OFF 4 MIRROR OFF 5 SHARPNESS 11 e 6 FACTORY DEFAULT YES
3. International Inc All rights reserved No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems The information in this publication is believed to be accurate in all respects However Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof The information contained herein is subject to change without notice Revisions or new editions to this publication may be issued to incorporate such changes
4. e 8 RETURN SHARPNESS 0 15 FACTORY NO YES DEFAULT See SPECIAL Menu Functions See for a description of the submenus and menu options SPECIAL Menu Functions Menu Item 1 CAMERA ID Description Sets a camera ID to be displayed on the monitor To add a camera ID maximum 10 characters including spaces UP DOWN LEFT or RIGHT menu control Select a lt lt CAMERA ID gt gt character then press ENTER to accept it The character is POSITION R BOT oa ABCDEFGHIJKLMNOPQRST saved and the cursor moves to the next position UVWXYZabcdefghijklimn oparstuvwxyz12345678 _ LEFT or RIGHT menu control Go back or forward in the 91 8 amp lt gt 0 name or number to make changes ID n RETURN POSITION Position the camera ID on the screen Press ENTER SET to confirm the position ID Sets a camera ID to be displayed Select RETURN when you are finished Honeywell Video Systems Head Office 2700 Blankenbaker Pkwy Suite 150 Louisville KY 40299 USA www honeywellvideo com 1 800 796 2288 Honeywell Security Australia Pty Ltd Unit 5 Riverside Center 24 28 River Road West Parramatta NSW 2150 Australia www honeywellsecurity com au 61 2 8837 9300 Honeywell Security Asia Pacific 33 F Tower A City Center 100 Zun Yi Road Shanghai 200051 China www asia security honeywell com 86 21 5257 4568 Honeywell Security Asia Flat A 16 F CDW Building 388 C
5. astle Peak Road Tsuen Wan N T Hong Kong www asia security honeywell com 852 2405 2323 Honeywell Security South Africa Honeywell House Bekker Street Truer Close Waterfall Park Midrand 1685 South Africa www honeywell com security za 27 11 695 8000 Honeywell Security Middle East Honeywell Middle East FZE Post Office Box 18530 LOB Building 08 Office 199 Jebel Ali Dubai U A E www honeywell com security me 971 04 881 5506 Honeywell Security UK Aston Fields Road Whitehouse Ind Est Runcorn Cheshire WA7 3DL UK www honeywell com security uk 44 1928 756 999 Honeywell Video Systems Northern Europe Netwerk 121 1446 WV Purmerend The Netherlands www honeywell com security nl 31 299 410 200 Honeywell Security Deutschland Johannes Mauthe StraBe 14 D 72458 Albstadt Germany www honeywell com security de 49 74 31 8 01 0 Honeywell Security France Parc Gutenberg 8 Voie La Cardon 91120 Palaiseau France www honeywell com security fr 33 01 64 53 80 40 Honeywell Security Italia SpA Via della Resistenza 53 59 20090 Buccinasco Milan Italy www honeywell com security it 39 02 4888 051 Honeywell Security Espana Mijancas 1 3a planta P Ind Las Mercedes 28022 Madrid Spain www honeywell com security es 34 902 667 800 Honeywell www honeywellvideo com 1 800 796 CCTV North America only HVSsupport honeywell com Document 8000 01955 Rev A 08 08 2008 Honeywell
6. camera to the video in connector on your monitor or video recorder 2 Connect the camera to a power supply appropriate for your installation 12 VDC or 24 VAC 3 Plug the power supply into an appropriate power source The power LED illuminates to show that the camera is receiving power Video Connections Figure 2 h LAMP terminal GND terminal AC24V DC12V terminal block Connecting LAMP Contact The HCD544 camera is equipped with LAMP and GND external contact terminals see Figure 2 When the LAMP terminal is connected to the GND terminal the camera is forced into night mode see DAY amp NIGHT It stays in night mode until the LAMP terminal is disconnected from the GND terminal Adjusting the Back Focus To adjust the back focus aim the camera towards a darker area or use a Neutral Density lens filter For best results there should be a minimum of 15 ft 4 5 m between the camera and the target focal area Loosen the setscrews see Figure 7 with a Phillips screwdriver Set the Zoom lens adjustment to Wide and the Focus lens adjustment to Near Adjust the back focus ring to focus the picture Ye Retighten the setscrews Document 800 01955 Rev A 08 08 Honeywell Mounting the Camera There are mounting points on the top and bottom of the camera see Figure 3 to mount the camera on a bracket or tripod Use standard sized mo
7. f one main SETUP menu for easy camera programming Figure 5 Menu Structure Main Menu Submenu Menu Options LENS DC MANUAL SHUTTER FLK MANUAL ESC i M E WHITE BAL ATW AWC PUSH LOCK AWC Too UAL AUTO USER MANUAL 3 WHITE BAL AWC a 4 BACKLIGHT 30dB aan 5 SPECIAL BACKLIGHT ON OFF 6 EXIT MENU 7 a AGC 18 dB 30 dB OFF SPECIAL See SPECIAL Menu See SETUP Menu Functions j for a description of the a submenus and menu options SETUP Menu Functions Menu Item Description 1 LENS Selects lens type DC Automatic Iris lens Press ENTER with DC selected to adjust the brightness level MANUAL Fixed lens 2 SHUTTER Adjusts shutter settings FLK Flickerless mode reduces on screen flickering MANUAL Adjust the shutter speed from 1 60 1 100 000 of a second NTSC or 1 50 1 100 000 PAL ESC Electronic Shutter Control Press ENTER to adjust the brightness level Not available with DC lens 3 WHITE BAL Controls color on the screen Press ENTER with ATW selected to White Balance Change the mode ATW Select Auto Tracking White Balance when the color temperature is 2500 K 8000 K for example when under a fluorescent light or outdoors AWC PUSH Automatically adjust the white balance to your specific environment When selected the white balance is locked AWC AUTO A faster AWB mode with a wider operatin
8. g range USER Adjust the red or blue gain from 0 255 MANUAL Increase or decrease the red or blue gain on screen BACKLIGHT Controls the light level to overcome severe backlighting conditions AGC Adjusts value of AGC gain Automatic Gain Increase the gain level 18 dB 30 dB in 2 dB increments to Control brighten the picture in low light conditions Noise distortion may develop OFF DAY amp NIGHT mode must be OFF to turn AGC OFF SPECIAL Opens the SPECIAL menu see SPECIAL Menu EXIT MENU Exits the SETUP menu and returns to video monitoring SAVE AND EXIT Exits the SETUP menu saving your changes and returns to video monitoring If the camera times out after five minutes of inactivity your changes are not saved EXIT Exits the SETUP menu without saving your changes RETURN Returns to the SETUP menu Menu Item Description 2 DAY amp NIGHT Menu Item Description MODE AUTO Depending on the light level the lt lt DAYANIGHT gt gt N camera automatically switches to night MODE AUTO mode DETECT TIME Ssec ON The camera is forced into night mode NSO TEEL at all times NIGHT COLOR B W OFF The camera never switches to night RETURN mode DETECT Sets the time 5 60 in 5 second increments TIME before the camera switches to day or night mode after detecting a switching threshold D gt N The light detection level 1 12 at which the
9. unting bolts to install the camera to a mounting bracket Caution Follow local installation codes for proper mounting bracket support capability Figure 3 Camera Mounting Top view shown Mounting point Making Final Adjustments Adjust the focus in your field of view until you see a clear image If necessary adjust the brightness using the OSD menu controls see LENS DC BRIGHTNESS or AGC Confirm the exposure on the monitor screen Programming OSD Menu Controls Figure 4 Camera Controller Camera OSD control 4 position plus center press ENTER Navigating through the menus A Press this control To do this ENTER Press and hold two seconds to enter SETUP menu Press to enter a screen or select a menu option ENTER UP DOWN lt O 4 Y LEFT RIGHT y lt gt Move vertically between menus and options Increase decrease a value Move horizontally between menus and options Indicates submenus Select the menu then press ENTER RETURN on OSD Exit the submenu Select RETURN submenus then press ENTER Note Menu display turns off automatically after five minutes of no activity Your changes will be saved OSD Menu Structure The HCD544 Series camera menu system consists o
Download Pdf Manuals
Related Search