400 Clip Fast Access System User Manual, Odetics, PBIO Option
Contents
1. OR Create an ID using the numeric keypad with a maximum of eight characters Press ENTER Press LOAD to create the selected CLIP ID If the selected CLIP ID already exists a warning message will be displayed To load the existing clip press ENTER Press ESC to exit without loading the existing clip CAPTURE FUNCTION The CAPTURE function allows source material from a VTR to be easily and quickly recorded into the VIDEO SERVER A CLIP ID is also created is always the Recorder the VIDEO SERVER Select VTR 2 VTR 3 or VTR 4 as the source VTR Any RS422 SONY protocol compatible VTR can be used Use the transport function keys to control the source VTR Each source VTR needs its own set of IN and OUT points a ENTER PREROLL VALUE 1 Press MENU and turn the Wheel to Enter PREROLL 2 Enter the desired preroll value using the ST300 s numeric keypad 3 Press ENTER to save the entered value OR Press ESC to exit without saving 15 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option b EXECUTE CAPTURE FUNCTION 1 2 3 4 5 Press VTR 2 VTR 3 or VTR 4 to select the source VTR Set IN amp OUT points as described in Section 13 SETTING THE IN OUT POINTS on the Source VTR Press SHIFT RECORD The display will prompt you for a CLIP ID A default CLIP ID will be shown Press LOAD to accept the default CLIP ID OR Use NEXT2. 10 GPI 2 In Stop 3 GPI 3 Out 11 GPI 3 In Recue 4 GPI 4 Out 12 GPI 4 In Next Cue 5 GPI 5 Out 13 GPI 5 In Last Cue 6 GPI 6 Out 14 GPI 6 In Recall 7 GPI 7 Out 15 GPI 7 In 8 Ground 25 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 23 KEY LAYOUT 203401 0 amp 400001 0 V3 1 amp T amp PBIO 57300 KEY CONFIGURATION AS WHITE RECUE MATTE KEYCAP LOAD 4 am H VTR WHITE WHITE KEYCAP N WATE KEYCAP CLIP WHITE KEYCAP LOOP 26 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option ST300 VTR DDR Controller 24 DNF CONTROLS LIMITED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one 1 year from the date of sale to the original purchaser from DNF Controls In order to enforce the rights under this warranty the customer must first contact DNF s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair If DNF s Customer Support Department cannot fix the problem the customer will be issued a Returned Merchandise Authorization number RMA The customer will then ship the defective product prepaid to DNF Controls with the RMA number clearly indicated on the customer s shipping document The merchandise is to be sh
3. Bus Enable the Peripheral Device Addresses assigned to the ST300 Enable the appropriate Learn Recall levels Enable the Timeline or Recall Trigger function Installation is complete Connection Diagram VIDEO PRODUCTION SERVER ST300 Lm SWITCHER cals POWER gn iur e Besa RESET py py PIN 3 BND PERIPHERAL BUS 7 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 8 VIDEO SERVER SETUP Select ODETICS Broadcast communications protocol on the VIDEO SERVER to be controlled Assign a serial port on the VIDEO SERVER through which the ST300 will control the server NOTES The VIDEO SERVER may not support LTC or VITC time modes in ODETICS Broadcast mode The ST300 will default to Tape Time if a non supported time mode is selected on the ST300 The Grass Valley Group PROFILE does not support search to a time location using Timecode LTC or VITC in ODETICS Protocol Tape Time mode TM must be selected on the ST300 In ODETICS Broadcast mode the VIDEO SERVER may ONLY allow Full Record INSERT and ASSEMBLE record modes may be disabled Setup is complete LOAD A CLIP Select a VTR by pressing VTR 1 VTR 2 VTR 3 or VTR 4 Press CLIP LIST to view the list of CLIP IDS that are resident on the Video Server The CLIP LIST indicator will turn on Press LOAD to create and load a new clip Creating a clip is described in the CREATE A CLIP Section 15 OR Turn
4. CUE LAST CUE and Wheel to edit the CLIP ID Use the NEXT CUE and LAST CUE keys to position the cursor Turn the Wheel to select the desired letter Press LOAD to accept the CLIP ID The ST300 will create the new CLIP ID on the Video Server The Source VTR will preroll to the IN Point then play At the Source VTR s IN point the RECORDER will go into record At the Source VTR s OUT point the RECORDER will terminate record post roll for 2 seconds then stop The Source VTR will search to the OUT point and stop The OUT point will be cleared The IN indicator will stay on The OUT indicator will turn off 16 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 19 TRANSFER CUE LIST a TRANSMIT CUE LIST FUNCTION The TRANSMIT CUE LIST function allows you to transmit your list of Cue Points to a PC using the provided utility software on the PC or to another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information 1 To Transmit Cue Points to Another ST300 a Connect the VTR4 connector on the rear of the ST300 to the VTR4 connector of the receiving ST300 using an RS422 9 pin cable with TX and RX lines crossed A turnaround cable b Press MENU Scroll the Wheel until Transmit CUE list YES Enter 5 is displayed d Press ENTER to start transmitting The Display shows Waiting
5. description PRODUCTION SWITCHER 1 2 3 Connect RS422 9 pin serial cable to the AUX connector on the rear of the ST300 Connect the other end of the cable to the Peripheral Bus Connector on the production switcher Communication Format 38 4K 8 1 To select a Production Switcher type Default 2 Grass Valley Group a Press MENU turn the Wheel until SWITCHER is displayed b Press Softkey to toggle between Sony and Grass Valley Press ESC at anytime to exit MENU mode The ST300 has 4 Peripheral Device Addresses one for each VTR that it controls To set the Device Address for each VTR a Press MENU and turn the wheel until Peripheral Address is displayed b Press VTR 1 VTR 2 VTR 3 or VTR 4 to select a VTR c Assign a Peripheral Device Address for that VTR from 0 to 23 by entering the desired address using the numeric keypad OR Press DEL to turn off the device d Select the next VTR and assign a Peripheral Device Address for it e When done press ESC to exit MENU mode 6 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 4 Select Parity a Press MENU and turn the Wheel until Parity is displayed b Press Softkey to select ODD EVEN or NONE parity to match the settings on the Production Switcher Press ESC to exit menu mode 5 Configure the production switcher On the production switcher Enable the Peripheral
6. or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display Press SHIFT MARK to start the LEARN The first line of the display will show Select VTRs The second line of the display will show Mark Lrn ESC cancel Press VTR 1 2 3 or 4 to select the VTR to be learned into the current Cue Point If the VTRs are ganged select one VTR that is part of the Gang The rest of the Gang will learn automatically Press MARK to complete the LEARN OR Press ESC to exit without LEARNING The ST300 will LEARN save the VTR Number 1 2 3 4 loaded CLIP ID and current IN amp OUT time to the selected Cue Point 9 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 8 RECALL A CLIP OR CLIP COMBINATION a RECALL ON THE PRODUCTION SWITCHER RECALL the desired REGISTER NUMBER The ST300 will automatically load the Learned clips on the Learned VTRs cue the clips to the Learned time then set the Learned GANG mode RECALL ON THE ST300 1 Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point on the numeric keypad The selected Cue Point number is shown on the bottom line of the display 2 Press LOAD The ST300 will automatically load the Learned clips on the Learned VTRs cue the clips to the Learned time then set the Learned GANG mode If RECALL MO
7. the Wheel to view the existing CLIP IDs on the video server Turn the Wheel clockwise to scroll forward or counter clockwise to scroll backward through the list of available CLIPs Backward scrolling is limited to the last 10 CLIP IDs viewed OR Manually enter a CLIP ID using the ST300 numeric keypad or PC keyboard if KBIO option Press LOAD to load the selected CLIP ID for playout Locate the clip to the desired IN time Press IN to mark the IN time Locate the clip to the desired OUT time Press OUT to mark the OUT time Repeat steps a f until clips are loaded into the desired VTRs Set the GANG mode if required 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 6 VIEW THE CLIP ID OF THE CURRENTLY LOADED CLIP Press SHIFT LOAD The bottom line will show the name of the loaded clip 7 LEARN A CLIP OR CLIP COMBINATION a LEARN ON THE PRODUCTION SWITCHER 1 2 3 51300 load clip s on the desired VTR s See LOAD A CLIP Section 5 Select and enable the Peripheral Device Addresses for the ST300 Do a LEARN to the desired REGISTER The ST300 will LEARN save the VTR number loaded CLIP ID and current IN amp OUT time into the REGISTER number in the ST300 b LEARN ON THE ST300 1 2 3 4 5 Load a clip s the desired VTR s See Section 5 LOAD A Select the desired Cue Point by pressing NEXT CUE LAST CUE
8. to transmit on the first line e When the Receiver is ready transfer starts automatically The Display now shows Transmitting cuelist f After the transfer is over the display shows Transfer is over for one second and then shows Waiting to transmit again g Connect another ST300 to transmit the list again OR Press ESC twice to exit the MENU mode 2 To Transmit Cue Points to a PC a Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using a RS422 to RS232 adapter b Repeat steps a thru g of To Transmit Cue Points to Another ST300 Section 17 a 1 17 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option b RECEIVE CUE LIST FUNCTION The RECEIVE CUELIST function allows you to receive a list of Cue Points from a PC or from another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information 1 To Receive Cue Points From Another ST300 a Connect the VTR4 connector on the back of the ST300 from the VTR4 connector of the transmitting ST300 using RS422 9 pin cable with TX and RX lines crossed A Turnaround Cable b Press MENU Scroll the Wheel until Receive CUE List YES Enter ExitZESC is displayed d Press ENTER to start receiving The Display shows Waiting to receive on the first line e When the Transmitter is ready transfer starts automa
9. 0CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 22 ST300 Power Size Weight Rear Panel Connectors Display Jog Shuttle Wheel Optional SPECIFICATIONS 90 VAC to 265 VAC adapter supplied with IEC connector x x H 12 x 6 x 1 5 front 3 0 rear T bar unit is 12 6 long 4 Ibs VTR2 VTR3 All DB9F DBFISF bene ERE DB9M AUK edite ei reir ep EP RE Sas DB9F Easy to read 2 line back lit LCD display User adjustable contrast With mechanical detents Slo mo 0 200 of Play Speed RS422 SERIAL CONNECTOR 9 Pin D Type Female Pin 1 Frame Ground 6 Receive Common 2 Receive A 7 Receive B 3 Transmit B 8 Transmit A 4 Transmit Common 9 Frame Ground 5 Spare POWER CONNECTOR 9 Pin D Type Male Pin 1 5v DC 6 5 VDC 2 5v DC 7 Ground 3 Ground 8 Ground 4 12 VDC 9 Ground 5 212 VDC AUX CONNECTOR PBvus IN RS422 SERIAL CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 2 No Connection 3 Receive B 4 Common 5 Spare 6 Common 7 No Connection 8 Receive A 9 Frame Ground 24 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option GPI IN OUT CONNECTOR 15 Pin D Type Female DB15F Pin Description Function Pin Description Function 1 GPI 1 Out 9 GPI 1 In Play 2 GPI 2 Out
10. 12843 Foothill Blvd Suite D Sylmar CA 91342 818 898 3380 voice 818 898 3360 fax www dnfcontrols com Model 4000CL O PBIO 400 CLIP FAST ACCESS SYSTEM WITH ODETICS PROTOCOL AND PERIPHERAL BUS INTERFACE OPTION VERSION 3 1 SOFTWARE USER MANUAL 1 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 1 Table of Contents REVISION HISTORY GETTING STARTED 2 D 3 a b 4 5 6 7 b 8 a b 13 SYSTEM DESCRIPTION EFINITIONS SYSTEM INSTALLATION ST300 S SM VTR DDR CONTROLLER PRODUCTION SWITCHER VIDEO SERVER SETUP LOAD A CLIP VIEW THE CLIP ID OF THE CURRENTLY LOADED CLIP LEARN A CLIP OR CLIP COMBINATION LEARN ON THE PRODUCTION SWITCHER LEARN ON THE ST300 RECALL A CLIP OR CLIP COMBINATION RECALL ON THE PRODUCTION SWITCHER RECALL ON THE ST300 RECUE THE CURRENTLY LOADED CLIP PLAY CLIP LOOP CLIP PBIO ENABLE DISABLE TRIGGER GRASS VALLEY GROUP VALUES SONY VALUES 14 a b c d 15 16 SETTING THE IN OUT POINTS MARKING THE IN OUT POINT ENTERING THE IN OUT POINTS VIEWING THE IN OUT POINTS CLEARING THE IN OUT POINT BVW MODE LEARN A CLIP OR CLIP COMBINATION BYW MODE ADVANCED FEATURES 17 18 a b 19 a b CREATE A CLIP CAPTURE FUNCTION ENTER PREROLL VALUE EXECUTE CAPTURE FUNCTION TRANSFER CUE LIST TRANSMIT CUE LIST FUNCTION RECEIVE CUE LIST FUNCTION 2 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Prot
11. DE in the Setup Menu is set to REDIR and a cue point contains only one clip then the clip will be REDIRECTED to load on the currently selected VTR not the Learned VTR RECUE THE CURRENTLY LOADED CLIP Press RECUE If an IN Point is marked the IN indicator is on the clip will RECUE to the IN Point If the IN point is not marked the clip will RECUE to the start of the clip OR Press SHIFT RECUE a b Enter the desired time to search to using the ST300 s numeric keypad Press ENTER to search to the entered time OR Press ESC to exit without searching 10 PLAY CLIP Load a clip from Cliplist or Recall a learned clip Mark IN OUT points if desired See Section 13 SETTING THE IN OUT POINTS Press PLAY The clip will play from the current point to the OUT point or if no OUT point is marked to the end of the clip If Autorecue Option is ON see Setup Menu the clip will recue to the IN point or the beginning of the clip once the OUT point or the end of the clip is reached 10 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 11 LOOPCLIP a LOAD a clip from CLIPLIST or RECALL a learned clip b Press LOOP ENABLE to loop a loaded clip The LOOP ENABLE indicator will turn on The second line of the display will show Looping clip Press STOP to stop the loop play If the clip ID ends with an asterisk it will automatically loo
12. HOLD to shuttle Release key to stop Set WIND Speed in HERES SHUTTLE Select SHUTTLE mode and enable Wheel SLOMO SLOMO Press SLOMO to slo mo VTR Turn the Wheel or move the T Bar if available to change the play speed Press SLOMO to STILL frame OR Press any transport key to exit SLOMO SLO MO SHIFT SLOMO For WHEEL ONLY SPEED Press SHIFT SLOMO to preset the slo mo speed PRESET Turn the Wheel to select desired speed Press ESC or any transport key to exit STOP STOP Press once to STILL frame VTR Press again to put VTR into STOP mode TIME MODE TIME MODE Press to toggle between Timecode TC VITC VT or Tape Timer SELECT TM display modes 22 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option LOOP CLIP LOOP ENABLE Press to loop a whole clip or a part between IN amp OUT points if marked PBIO PBIO Toggle the key to enable disable PBus commands ENABLE If the LED is on PBIO is enabled DISABLE If the LED is OFF PBIO is disabled PLAY PLAY Plays the clip If the OUT point is set stops at the OUT point If no OUT point is set plays to the end of the clip If the clip ends with loops the clip PLAY TO SHIFT PLAY Plays to the end of the clip THE END OF Disregards the OUT point and the THE CLIP ALIGN SHIFT STOP Restablishes the initial offset between ganged channels GANGED CHANNELS 23 400
13. IO Option 14 15 SETTING THE IN OUT POINTS a MARKING THE IN OUT POINT 1 Locate the clip to the desired IN OUT time 2 Press IN OUT to set the IN OUT Point The IN OUT indicator will turn on The display will show IN OUT xx xx xx xx where xx xx xx xx is the saved time b ENTERING THE IN OUT POINTS 1 Press SHIFT IN to manually enter a new IN OUT time 2 Press ENTER to save the entered time or press ESC to exit without saving c VIEWING THE IN OUT POINTS 1 When the IN OUT indicator is on Press IN OUT to view the existing IN OUT Point 2 While viewing the IN OUT Point Press MARK to overwrite the saved time with the current time Press RECUE to search to the IN OUT point d CLEARING THE IN OUT POINT Press and hold DEL then press and release IN The IN OUT indicator goes off BVW MODE If you wish to control a tape machine or a DDR with the 4000CL O system select control MODE BVW see Setup Menu section In this mode the media is accessed by timecode not by clip names The cuepooints in BVW mode consist only of IN point OUT point and Gang information The following functions are not available in BVW mode View Clip ID Clip Loop Clip Capture Create Clip All other functions work as described in the manual 13 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 16 LEARN A CLIP
14. OR CLIP COMBINATION BVW MODE Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display Locate the clip to the desired IN time Press IN to mark the IN time Locate the clip to the desired OUT time Press OUT to mark the OUT time Press SHIFT MARK to start the LEARN The first line of the display will show Select VTRs The second line of the display will show Mark Lrn ESC cancel Press VTR 1 VTR 2 VTR 3 or VTR 4 to select the VTR to be learned into the current Cue Point If the VTRs are ganged select one VTR that is part of the Gang The rest of the Gang will learn automatically Press MARK to complete the LEARN OR Press ESC to exit without LEARNING The ST300 will LEARN save the VTR number 1 2 3 4 and current IN amp OUT time to the selected Cue Point 14 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option Advanced Features 17 CREATE A CLIP 18 Press CLIP LIST The CLIP LIST indicator turns on The display will show CREATE NEW CLIP Press LOAD The display will show the default CLIP ID Press LOAD to accept the default CLIP ID OR Use NEXT CUE LAST CUE and Wheel to create a CLIP ID Use the NEXT CUE and LAST CUE keys to position the cursor Turn the Wheel to select the desired letter
15. and provides fast access to existing video clips stored in non volatile memory in the ST300 Remotely view the CLIP IDs that exist in the Video Server under control Any clip in the SHOTLIST can be quickly loaded by simply entering the associated 3 digit number of its location then pressing LOAD Press PLAY to play the clip Press to recue to the beginning of the clip DEFINITIONS Throughout this document VTR DDR VDR amp Video Server will be referred to collectively as Video Server Q The ST300 S SM as the ST300 Q Words surrounded by brackets for example ENTER are keys on the ST300 XXX XXX means hold the two keys down simultaneously Q Words surrounded by brackets and shown in italic for example ENTER are multi function softkeys on the ST300 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 3 SYSTEM INSTALLATION a ST300 S SM VTR DDR CONTROLLER 1 2 3 4 Plug one end of a 9 conductor RS422 serial cable into the VTR 1 2 3 or 4 connector on the rear of the ST300 Plug the other end of the cable into the REMOTE connector on the Video Server Connect the supplied POWER SUPPLY APX 4108 into the POWER connector on the rear of the ST300 Plug the Power Supply into an outlet 90 VAC to 240 VAC Check SETUP MENU prior to using the ST300 to confirm proper Record mode and other User settable modes Select CONTROL MODE ODETICS See menu
16. ipped to DNF Controls 12843 Foothill Blvd Suite D Sylmar CA 91342 USA Failure to obtain a proper RMA number prior to returning the product may result in the return not being accepted or in a charge for the required repair DNF Controls at its option will repair or replace the defective unit DNF Controls will return the unit prepaid to the customer The method of shipment is at the discretion of DNF Controls principally UPS Ground for shipments within the United States of America Shipments to international customers will be sent via air Should a customer require the product to be returned in a more expeditious manner the return shipment will be billed to their freight account This warranty will be considered null and void if accident misuse abuse improper line voltage fire water lightning or other acts of God damaged the product All repair parts are to be supplied by DNF Controls either directly or through its authorized dealer network Similarly any repair work not performed by either DNF Controls or its authorized dealer may void the warranty After the warranty period has expired DNF Controls offers repair services at prices listed in the DNF Controls Price List DNF Controls reserves the right to refuse repair of any unit outside the warranty period that is deemed non repairable DNF Controls shall not be liable for direct indirect incidental consequential or other types of damage resulting from the use of the p
17. nge Preset NOTE The T BAR has a fixed speed range of 0 gt 200 with a detent at 100 play speed For Wheel only Press Softkey SPDRANGE to select SLOMO speed ranges Press Softkey to select 0 gt 200 OR 100 gt 200 Press Softkey BACK to return to SLOMO MENU Press ESC to exit MENU OR Turn the wheel to select another item Continued on next page 19 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option For Wheel only Press Softkey PRSET to select the SLOMO Preset Speed Mode Press Softkey UPDATE When exiting SLOMO mode the last used speed is saved in the Preset Speed register Press Softkey STATIC The Preset Speed register is NOT updated when exiting SLOMO mode It is only changed by SHIFT SLOMO PRESET SLOMO GANG MODE Press Softkey to select PERMANENT GANG described in the FUNCTION Table or TEMPORARY GANG In TEMPORARY mode press and hold the VTR key that you want to read status from then press the VTR s of those VTRs that you want to include in the gang Release the keys The LED on the monitored VTR blinks all other VTRs in the gang stay on constantly To break the temporary gang press any VTR key ST300 SETUP ST300 SETUP Clear Cues SetDefault Press Softkey beneath ClearCues to clear all Cue Points to 00 00 00 00 Press Softkey YES when asked Are You Sure Press Softkey beneath SetDefault to set ST300 to defaul
18. ocol PBIO Option p Re 15 15 15 15 16 17 17 18 REFERENCE 20 SETUP MENU 21 FUNCTION TABLE 22 SPECIFICATIONS RS422 SERIAL CONNECTOR POWER CONNECTOR AUX CONNECTOR PBus IN RS422 SERIAL CONNECTOR GPI IN OUT CONNECTOR 23 KEY LAYOUT 24 DNF CONTROLS LIMITED WARRANTY 19 19 22 24 24 24 24 22 26 27 Manual 4 6 081004 Document No 4000CL O PBIO Vs 3 1 User Manual doc 3 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 1 REVISION HISTORY 010203 Rev 070903 Rev 112403 Rev 012304 Rev 080404 Rev 081004 Rev 4 1 4 2 4 3 4 4 4 5 4 6 Corrected Loop Clip section Added Play Clip BVW Mode section Added Gang and Autorecue setup to Setup Menu section Company header information revised Updated Transmit Cue List Function and Receive Cue List Function description Added DNF Controls Limited Warranty Changed Key Layout Added section LEARN A CLLIP OR CLIP COMBINATION BVW MODE Added T bar dimension 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option Getting Started 2 5 SYSTEM DESCRIPTION NOW production switchers can load amp play
19. p when either LOOP ENABLE or PLAY is pressed 12 PBIO ENABLE DISABLE On the ST300 press the PBIO key to enable or disable PBIO When disabled the ST300 will ignore all Pbus commands When enabled the ST300 will respond to all Pbus commands When enabled and Pbus commands are received the key s LED will flash 11 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 13 TRIGGER The operator fires a trigger using either the Timeline or Run function on the production switcher The ST300 puts the Video Server into the following modes based upon the trigger value GRASS VALLEY GROUP VALUES Trigger Value Mode 0 Play 1 Recue to beginning of clip 2 Slo mo using ST300 Wheel Preset or T Bar Speed 3 Reverse Play 4 Still Frame 5 Loop 6 Record 7 or greater Play SONY VALUES Trigger Value Mode 0 Recue to beginning of clip 1 Play 2 Slo mo using ST300 Wheel Preset or T Bar Speed 3 Reverse Play 4 Still Frame 5 Loop 6 Record 7 or greater Play To control more than one VTR enable the Peripheral Device Address for the required VTRs The Trigger will be sent to the enabled devices OR GANG the required VTRs on the ST300 Refer to the Function Table for GANG instructions Enable the Peripheral Device Address for one of the GANGed VTRs The Trigger will be sent to the enabled VTR The other VTRs in the GANG will perform the same action 12 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PB
20. roduct 27 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option
21. s putting out on the PBUS ODD EVEN or NONE ENTER 00 00 00 00 PREROLL Enter Preroll value using the numeric keypad RECORD Enter up to 99 frames record delay used in Capture Function DELAY Typical value is 3 frames CONTROL Select Control mode OdeticsAB VW MODE Have Odetics selected for video server control and clip access SELECT Have BVW selected to access media by timecode TRANSMIT Transmits Cuelist to another ST300 or to a PC CUELIST See Section 17 a TRANSMIT CUE LIST FUNCTION RECEIVE Receives Cuelist from another ST300 or a PC CUELIST See Section 17 b RECEIVE CUE LIST FUNCTION 21 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option 21 FUNCTION TABLE GOTO SHIFT RECUE Search the VTR to the manually entered time ENTERED TIME Use the ST300 numeric keypad Press ENTER or RECUE NOTE GRASS VALLEY GROUP Profile does not support TC or VITC time search SHIFT VTR 1 Individually press the VTR keys to be included in the gang the LED OR above the key will turn on Press the VTR key again to remove from SHIFT VTR 2 gang the LED above the key will turn off Press ESC to exit OR SHIFT VTR 3 The VTR LEDs that are on show the gang OR The flashing LED shows which VTR is currently selected SHIFT VTR 4 MENU RECORD REC Places VTR into the Record mode selected by RECORD MODE in the SETUP MENU Press RECORD or RECORD PLAY ce Press and
22. t settings Press Softkey YES when asked Are You Sure IMPORTANT NOTE Please set these items during initial installation DISPLAY The version number and date for the currently installed software is displayed SOFTWARE For example VERSION 4000CL O PBIO V3 0 072400 SYNC Set to ON if black burst is supplied to the Ref Video connector on the rear panel Set to OFF if no blackburst is supplied AUTO RECUE If Set to ON the video automatically recues back to the IN point or to the beginning of the clip if there is no IN point after the playout reaches OUT point or the end of the clip RECORD Press Softkey to select single button or 2 button record RECORD REC Only OR REC PLAY RECALL MODE Press Normal or Redirect Redir When one and only one clip is learned into a Cue Point the Clip will be REDIRECTED to load on the currently selected VTR if REDIR is on If REDIR is off the Clip will be loaded on the VTR it is LEARNED into 20 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option PBIO ADDRESS Press VTR key to select the VTR to which to assign a PBIO address Display shows PBIO Address 00 Enter 00 23 Enter address number desired on numeric keypad Repeat for all VTRs assigned SWITCHER TYPE Select your switcher type Grass Valley Group default or Sony For Philips DD35 with PBus use GVG PARITY Select Parity type Switcher i
23. tically The Display now shows Receiving cuelist f After the transfer is over the display shows Done Success Press any key g Press any key The display shows Receive cuelist message h Press ESC to exit the MENU mode 2 To Receive Cue Points From the PC a Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using RS422 to RS232 adapter b Repeat steps a h of To Receive Cue Points From Another ST300 Section 17 b 1 18 4000CL O Vs 3 1 400 Clip Fast Access System Odetics Protocol PBIO Option Reference 20 SETUP MENU Press MENU The MENU indicator will turn on Turn the Wheel to select item to change Press MENU OR use the Softkeys to change the desired mode for that option Turn the Wheel at anytime to select another item Press ESC at anytime to exit SETUP MENU The MENU indicator will turn off MENU MODES Turning Wheel clockwise RECORD Press Softkey to select the desired record mode Assemble Insert Lockout or Crash Full WIND MODE Press Softkey to select HOLD fast wind is maintained only while key is depressed OR LATCH fast wind is initiated and maintained with momentary key press Select fast wind speed 03 9X etc by pressing Softkey SLOMO ST300 display shows SLOMO with WHEEL Non T B ion Non ar version SpdRange Preset ST300 display shows SLOMO with TBAR T Bar version Wheel SpdRa
24. video clips on Grass Valley Group PROFILE Leitch VR and other DDRs amp Video Servers Use the EMEM or SNAPSHOT Learn amp Recall functions of the production switcher to load and play a video clip from a Recall or timeline Use the Run and Trigger functions of the production switcher to Play Stop or the video clip The 400 Clip Fast Access System consists of the ST300 SSM VTR Controller and Shotlist Software The Video Server must support ODETICS Broadcast Protocol The PERIPHERAL BUS INTERFACE Option for the ST300 VTR Controller is special software in the ST300 With this Option the ST300 has 4 Peripheral Device Addresses one for each VTR that it controls This allows the production switcher to control any and all VTRs connected to the ST300 Upon receipt of the Learn command from the production switcher the ST300 saves the CLIP IDs of the currently loaded clips the current time of each clip the VTRs they are loaded on and the current GANG mode into the appropriate Cue Point When the Recall command is received the ST300 loads the Learned Clips onto the Learned VTRs cues the Clip to the Learned time then restores the Learned GANG mode Learn amp Recall may also be done directly from the ST300 without the production switcher The Trigger function on the production switcher puts the selected VTRs into Play Stop Recue or other available modes The SHOTLIST contains up to 400 CLIP IDs
Download Pdf Manuals
Related Search