CP-RIO3-05 User Guide, Rev. 1.0
Contents
1. rJ2 Note Pi F GND Pinrow Z NC a BCDE ID 1044 0711 Rev 1 0 Page 2 11 Functional Description CP RIO3 05 m Table 2 10 Rear I O CompactPCI Bus Connector rJ2 Pinout PIN ROWZ ROWA ROW B ROW C ROW D ROW E ROW F 22 NC NC NC NC NC NC GND 21 NC GPI4 GND USB1 USB0 USB1_PWR_5V GND 20 NC GPO1 GND USB1 USB0 USB0_PWR_5V GND 19 NC GND GND RIO_3 3V BAT GPI2 RIO_3 3V GND 18 NC IPC_DA IPC_DA GPOO IPD_DA IPD_DA GND 17 NC IPC_DB IPC_DB PRST IPD_DB IPD_DB GND 16 NC IPC_DC IPC_DC NC GND IPD_DC GND 15 NC IPC_DD IPC_DD NC GPIO IPD_DC GND 14 NC IPB_DA IPB_DA IPD_DD IPB_DC IPB_DC GND 13 NC IPB_DB IPB_DB IPD_DD IPB_DD IPB_DD GND 12 NC IPA_DA IPA DA IP_PWR IPA_DC IPA_DC GND 11 NC IPA_DB IPA DB COM1_RI IPA_DD IPA_DD GND 10 NC GND GND VGA_RED COM1_DSR GND GND 9 NC SATAOTX COM1 RXD VGA HSYNC COM2 RX4 SATA1TX GND RXD 8 NC SATAOTX COM1_CTS VGA BLUE COM2_RX SATA1TX GND CTS 7 NC GND GND VGA_DDC_DATA GND GND GND 6 NC SATAORX COM1_RTS VGA_GREEN COM2_TX SATA1RX GND RTS 5 NC SATAORX COM1_TXD VGA_VSYNC COM2_TX SATA1RX GND TXD 4 NC VI O RIO_5V VGA_DDC_CLK COM1_DCD COM1_DTR GND 3 NC GPII GND NC GPI3 GPO2 GND 2 NC NC NC NC NC NC GND 1 NC NC GND NC NC NC GND Warning The RIO XXX2. Two Year Warranty Kontron grants the original purchaser of Kontron s products a TWO YEAR LIMITED HARDWARE WARRANTY as described in the following However no other warranties that may be granted or implied by anyone on behalf of Kontron are valid unless the consumer has the express written consent of Kontron Kontron warrants their own products excluding software to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase This warranty is not transferable nor extendible to cover any other users or long term storage of the product It does not cover products which have been modified altered or repaired by any other party than Kontron or their authorized agents Furthermore any product which has been or is sus pected of being damaged as a result of negligence improper use incorrect handling servicing or maintenance or which has been damaged as a result of excessive current voltage or tem perature or which has had its serial number s any other markings or parts thereof altered de faced or removed will also be excluded from this warranty If the customer s eligibility for warranty has not been voided in the event of any claim he may return the product at the earliest possible convenience to the original place of purchase togeth er with a copy of the original document of purchase a full description of the application the product is used on and a description of the defect
3. The following safety precautions must be observed when installing or operating the CP RIOS 05 Kontron assumes no responsibility for any damage resulting from failure to comply with these requirements Caution A Ensure that the system main power is removed prior to installing or removing the CP RIO3 05 Ensure that there are no other external voltages or signals being applied to the CP RIO3 05 or other boards within the system Failure to do so could endanger your life or health and may damage the CP RIO3 05 or other system components including process side signal conditioning equipment ESD Equipment The CP RIO3 05 contains electrostatically sensitive devices Please observe the necessary precautions to avoid damage to the CP RIO3 05 Discharge your clothing before touching the assembly Tools must be dis charged before use Do not touch components connector pins or traces f working at an anti static workbench with professional discharging equipment please do not omit to use it ID 1044 0711 Rev 1 0 Page 3 3 Installation CP RIO3 05 3 2 Initial Installation Procedures The following procedures are applicable only for the initial installation of the CP RIO3 05 in a system To perform an initial installation of both the CP RIO3 05 in a system proceed as follows 1 Ensure that the safety requirements indicated in Chapter 3 1 are observed Warning Failure to comply with the instruction below ma
4. Pack the product in such a way as to ensure safe transportation see our safety instructions Kontron provides for repair or replacement of any part assembly or sub assembly at their own discretion or to refund the original cost of purchase if appropriate In the event of repair re funding or replacement of any part the ownership of the removed or replaced parts reverts to Kontron and the remaining part of the original guarantee or any new guarantee to cover the repaired or replaced items will be transferred to cover the new or repaired items Any exten sions to the original guarantee are considered gestures of goodwill and will be defined in the Repair Report issued by Kontron with the repaired or replaced item Kontron will not accept liability for any further claims resulting directly or indirectly from any warranty claim other than the above specified repair replacement or refunding In particular all claims for damage to any system or process in which the product was employed or any loss incurred as a result of the product not functioning at any given time are excluded The extent of Kontron liability to the customer shall not exceed the original purchase price of the item for which the claim exists Kontron issues no warranty or representation either explicit or implicit with respect to its products reliability fitness quality marketability or ability to fulfil any particular application or purpose As a result the produ
5. n Note When using a Serial ATA cable it is recommended to use a special right angled Serial ATA cable due to possible space limitations within the system For further information please contact Kontron Note To ensure secure connectivity the SATA connector supports the use of SATA II cables SATA cables with locking latch SATA Il support for external SATA devices is a function of the backplane the SATA device and cabling In general the more connectors and cabling involved the less chance of achieving proper external SATA II device operation Page 2 10 ID 1044 0711 Rev 1 0 CP RIO3 05 Functional Description 2 1 7 Rear I O Interface on CompactPCI Connector rJ2 The CP RIO3 05 is equipped with one CompactPCI rear I O connector rJ2 Warning To support the rear I O feature a SU CompactPCI backplane with rear I O sup port as well as a compatible and correctly configured CPU board are required Do not plug the CP RIO3 05 in a backplane without rear I O support Failure to comply with the above will result in damage to the CP RIO3 05 Warning The CP RIO3 05 may be used only with CPU boards that have a compatible rear I O CompactPCI connector pinout such as the CP3002 RA and the CP3002 RC from Kontron Failure to comply with the above may result in damage to the CP RIO3 05 or the CPU board amp Figure 2 8 Rear I O CompactPCI Connectors rJ2
6. personnel only Caution Electric Shock Before installing a not hot swappable Kontron product into a system always ensure that your mains power is switched off This applies also to the installation of piggybacks Serious electrical shock hazards can exist during all installation repair and maintenance operations with this product Therefore always unplug the power cable and any other cables which provide external voltages before performing work Special Handling and Unpacking Instructions ESD Sensitive Device Electronic boards and their components are sensitive to static elec tricity Therefore care must be taken during all handling operations and inspections of this product in order to ensure product integrity at all times Do not handle this product out of its protective enclosure while it is not used for operational purposes unless it is otherwise protected Whenever possible unpack or pack this product only at EOS ESD safe work stations Where a safe work station is not guaranteed it is important for the user to be electrically discharged before touching the product with his her hands or tools This is most easily done by touching a metal part of your system housing It is particularly important to observe standard anti static precautions when changing piggy backs ROM devices jumper settings etc If the product contains batteries for RTC or memory backup ensure that the board is not placed on conductive surfaces
7. 11 Rev 1 0 CP RIO3 05 Introduction 1 2 3 Board Layout Figure 1 3 CP RIO3 05 Board Layout Top View SW1 Reset Button ETH C D J6 ETH A B J9 USBO0 1 m E mmm J5 J4 SATAO SATA1 J3 COM2 ID 1044 0711 Rev 1 0 Page 1 5 Introduction CP RIO3 05 1 3 Technical Specification Table 1 1 CP RIO3 05 Main Specifications CP RIO3 05 SPECIFICATIONS VGA One VGA interface on a 15 pin D Sub connector J8 for connecting a standard analog monitor 29 Ethernet Four Gigabit Ethernet interfaces implemented as two dual RJ 45 connec tors J6 ETH A ETH B and J7 ETH C ETH D E COM Two serial ports ES e COMI RS 232 implemented as a 9 pin D Sub connector J2a e COM2 RS 232 RS 422 implemented as a 9 pin D Sub connec tor J3a SATA Two SATA II interfaces with SATA Il repeater implemented as two onboard connectors J4 and J5 for connecting external SATA devices via a SATA cable COM Two serial ports COMI RS 232 implemented as a 10 pin connector J2 59 e COM2 RS 232 RS 422 implemented as a 10 pin connector J3 s The onboard serial port connectors J2 and J3 are connected to the front 2 5 panel COM connectors J2a and J3a via flat cables bd GPIO One 10 pin general purpose I O connector J10 with the following fea tures Five general purpose inputs Three general purpose o
8. G kontron User Guide CP RIO3 05 3U CompactPCI Rear Transition Module Doc ID 1044 0711 Rev 1 0 February 18 2011 If it s embedded it s Kontron Preface CP RIO3 04S Revision History Publication Title CP RIO3 05 3U CompactPCI Rear Transition Module Brief Description of Changes Date of Issue 1 0 Initial issue 18 Feb 2011 Imprint Kontron Modular Computers GmbH may be contacted via the following MAILING ADDRESS TELEPHONE AND E MAIL Kontron Modular Computers GmbH 49 0 800 SALESKONTRON SudetenstraBe 7 sales kontron com D 87600 Kaufbeuren Germany For further information about other Kontron products please visit our Internet web site www kontron com Disclaimer Copyright 2011 Kontron AG All rights reserved All data is for information purposes only and not guaranteed for legal purposes Information has been carefully checked and is believed to be accurate however no responsibility is assumed for inaccuracies Kontron and the Kontron logo and all other trademarks or registered trademarks are the property of their respective own ers and are recognized Specifications are subject to change without notice Page ii ID 1044 0711 Rev 1 0 CP RIO3 05 Preface Table of Contents itle sicilia il qus M ii PRISE ANNIE P M il Table of PUT iii TSE rior mee
9. TL signaling The following figure and table provide pinout information for the onboard GPIO connector J10 Figure 2 6 GPIO Connector J10 Table 2 8 GPIO Connector J10 Pinout PIN SIGNAL DESCRIPTION I O 1 GPIO General purpose input 0 l 2 10 2 GPOO General purpose output 0 O 3 GPI1 General purpose input 1 I DOG 4 GPO1 General purpose output 1 O eee z 5 GPI2 General purpose input 2 1 6 GPO2 General purpose output 2 O J10 purp p GPIO 7 GPI3 General purpose input 3 8 3 3V 3 3V power 9 GPI4 General purpose input 4 10 GND Signal ground ID 1044 0711 Rev 1 0 Page 2 9 Functional Description CP RIO3 05 2 1 6 Serial ATA Interfaces The CP RIO3 05 provides two onboard SATA II interfaces implemented as two onboard SATA connectors J4 and J5 used to connect standard SATA devices via SATA cables A SATA II repeater is provided on the CP RIO3 05 to improve the signal performance The following figure and table provide pinout information for the SATA connectors J4 and J5 Figure 2 7 SATA Con J4 and J5 Table 2 9 SATA Connectors J4 and J5 Pinout PIN SIGNAL DESCRIPTION 1 0 1 GND Ground signal 1 Coo SATA_TX Differential Transmit O i gt 1 SATA TX Differential Transmit O J5 J4 GND Ground signal SATAO SATA1 SATA RX Differential Receive SATA RX Differential Receive 4 GND Ground signal NN OD oO G
10. USB Connector J9 Table 2 3 Dual USB Connector J9 Pinout PIN SIGNAL DESCRIPTION 1 0 4 1 vcc VCC signal o USB1 USBO 2 UVO Differential USB 1 0 1 3 UVO Differential USB I O 4 GND GND signal Note The USB host interfaces on the CP RIO3 05 rear I O module can be used with maximum 500 mA continuous load current as specified in the Universal Serial Bus Specification Revision 2 0 Short circuit protection is provided All the sig nal lines are EMI filtered Note The rear I O interface supports the USB 1 1 and USB 2 0 standards When connecting peripheral devices to USB 2 0 ports always ensure that appropriate cables are used ID 1044 0711 Rev 1 0 Page 2 5 Functional Description CP RIO3 05 2 1 4 COM Interfaces The CP RIO3 05 module provides two COM ports COM1 and COM2 on the front panel for connecting RS 232 RS 422 devices The COM ports are realized as 9 pin D Sub connectors J2a and J3a and connected via flat cables to the 10 pin onboard connectors J2 and J3 COMI is a full featured RS 232 interface COM2 is an RS 422 interface switchable to limited RS 232 via the uEFI BIOS of the CP3002 RC CP3002 RA COM corresponds to COMA on the CP3002 RA CP3002 RC COM corresponds to COMB on the CP3002 RA CP3002 RC The following figure and tables provide pinout information for the 9 pin D Sub COM connectors J2a and J3a located on the front panel F
11. ables that may be connected to the CP RIO3 05 Unscrew the front panel retaining screws Disengage the CP RIO3 05 from the backplane by first unlocking the ejection handle and then by pressing the handle as required until the CP RIO3 05 is disengaged 6 After disengaging the CP RIO3 05 from the backplane pull it out of the slot 7 Dispose of the CP RIO3 05 as required oR OW E ID 1044 0711 Rev 1 0 Page 3 5 Installation CP RIO3 05 3 4 Installation of External Serial ATA Devices Up to two external SATA devices may be connected to the CP RIO3 05 via the onboard SATA connectors J4 and J5 as well as the appropriate SATA cables Some symptoms of incorrectly installed SATA devices are Device on a SATA channel does not spin up check power cables and cabling May also result from a bad power supply or SATA device The SATA connector on the CP RIO3 05 provides only a data connection The power for this device must be supplied by a separate connector For further information refer to the respective documentation of the device SATA device fail message at boot up may be a bad cable or lack of power going to the drive Warning The incorrect connection of power or data cables may damage the SATA device and or the CP RIO3 05 Page 3 6 ID 1044 0711 Rev 1 0
12. cts are sold as is and the responsibility to ensure their suitability for any given task remains that of the purchaser In no event will Kontron be liable for direct indirect or consequential damages resulting from the use of our hardware or software products or documentation even if Kontron were advised of the possibility of such claims prior to the purchase of the product or during any period since the date of its purchase Please remember that no Kontron employee dealer or agent is authorized to make any modification or addition to the above specified terms either verbally or in any other form written or electronically transmitted without the company s consent E ID 1044 0711 Rev 1 0 Page xiii Preface CP RIO3 05 This page has been intentionally left blank Page xiv ID 1044 0711 Rev 1 0 CP RIO3 05 Introduction Chapter Introduction ID 1044 0711 Rev 1 0 Page 1 1 Introduction CP RIO3 05 This page has been intentionally left blank Page 1 2 ID 1044 0711 Rev 1 0 CP RIO3 05 Introduction 1 Introduction 1 1 Board Overview The CP RIO3 05 3U CompactPCI rear transition module has been designed for use with the CP3002 RC and the CP3002 RA 3U CompactPCI CPU boards from Kontron and provides comprehensive rear I O functionality for peripherals In order to use the CP RIO3 05 a 3U CompactPCI backplane with rear I O support as well as a compatible and correctly confi
13. emehls siriaca 3 3 3 2 Initial Installation Procedures 3 4 3 8 Standard Removal Procedures seen 3 5 3 4 Installation of External Serial ATA Devices 3 6 Page iv ID 1044 0711 Rev 1 0 CP RIO3 05 Preface List of Tables 1 1 CP RIO3 05 Main Specifications esses ssis nenne nannten 1 6 Fe SMAI ANG licia lillo 1 7 1 3 Additional Standards for Modules Providing Ruggedized Service 1 8 1 4 Related PUbliCallone uuu sauna etas ii 1 8 2 1 D Sub VGA Connector 48 Pinout i 2 3 2 2 Pinout of Gigabit Ethernet Connectors J6 and J7 2 4 2 3 Dual USB Connector J9 Pinout siria 2 5 2 4 D Sub COM Connector J2a COM1 Pinout 2 6 2 5 D Sub COM Connector J3a COM2 Pinout 2 7 2 7 Onboard Serial Port Connector J3 COMJ2 Pinout 2 8 2 6 Onboard Serial Port Connector J2 COM1 Pinout 2 8 2 8 GPIO Connector J10 Pinout lacca 2 9 2 9 SATA Connectors J4 and J5 Pinout esses 2 10 2 10 Rear I O CompactPCI Bus Connector rJ2 Pinout 2 12 ID 1044 0711 Rev 1 0 Page v Preface CP RIO3 05 This page has been intentionally left blan
14. gured CPU board are required For further information concerning possible compatibility with other 3U Kontron CompactPCI boards please contact Kontron The CP RIO3 05 comes with four Gigabit Ethernet ports two USB 2 0 ports one VGA CRT port and two serial ports COM1 and COMO on the front panel as well as two onboard SATA ports for connection to external SATA devices one onboard GPIO port two onboard serial ports COM1 and COM2 and one CompactPCI connector for connecting the CP RIO3 05 to the backplane For resetting the CP3002 RC CP3002 RA the CP RIO3 05 provides an on board reset button 1 2 Board Diagrams The following diagrams provide additional information concerning the boards functionality and component layout 1 2 1 Functional Block Diagram Figure 1 1 CP RIO3 05 Functional Block Diagram RS 232 es RS 232 LN M RS 232 x RS 232 RS 422 n m lei 4x Gigabit Ethernet 4x Gigabit Ethernet 2x USB 2 0 SATA II SATA II SATA II Repeater SATA II SATA II GPIO Components Onboard Front Panel P Connector Connector ID 1044 0711 Rev 1 0 Page 1 3 Introduction CP RIO3 05 1 2 2 Front Panel Figure 1 2 CP RIO3 05 Front Panel CP RIO3 05 8 oO gt Q e XEPEREREPS Li r1 USBO Note 3 ke The Ethernet LEDs have no functionality on the CP RIO3 05 Page 1 4 ID 1044 07
15. igure 2 4 D Sub COM Connectors J2a COM1 and J3a COM2 Table 2 4 D Sub COM Connector J2a COM1 Pinout PIN SIGNAL DESCRIPTION 1 0 DCD Data carrier detect 2 RXD Receive data 3 TXD Transmit data O 4 DTR Data terminal ready o 5 GND Signal ground 6 DSR Data send request 7 RTS Request to send O 8 CTS Clear to send 9 RI Ring indicator Page 2 6 ID 1044 0711 Rev 1 0 CP RIO3 05 Functional Description Table 2 5 D Sub COM Connector J3a COM2 Pinout 1 0 DESCRIPTION SIGNAL SIGNAL DESCRIPTION 1 0 Not connected NC 1 NC Not connected Receive data RXD 2 RXD Receive data O Transmit data TXD 3 TXD Transmit data o Not connected NC 4 NC Not connected Signal ground GND 5 GND Signal ground Not connected NC 6 NC Not connected O Request to send RTS 7 TXD Transmit data o Clear to send CTS 8 RXD Receive data Not connected NC 9 NC Not connected Note The RS 232 signals DCD DTR DSR and RI are not supported on the J3 connector The following figure and tables provide pinout information for the onboard COM connectors J2 and J3 Figure 2 5 Onboard Serial Port Connectors J2 COM1 and J3 COM2 ei eni J3 n ID 1044 0711 Rev 1 0 Page 2 7 Functional Description CP RIO3 05 Table 2 6 Onboard Serial Port Connect
16. including anti static plas tics or sponges They can cause short circuits and damage the batteries or conductive circuits on the board ID 1044 0711 Rev 1 0 Page xi Preface CP RIO3 05 General Instructions on Usage In order to maintain Kontron s product warranty this product must not be altered or modified in any way Changes or modifications to the device which are not explicitly approved by Kontron and described in this manual or received from Kontron s Technical Support as a special handling instruction will void your warranty This device should only be installed in or connected to systems that fulfill all necessary technical and specific environmental requirements This applies also to the operational temperature range of the specific board version which must not be exceeded If batteries are present their temperature restrictions must be taken into account In performing all necessary installation and application operations please follow only the instructions supplied by the present manual Keep all the original packaging material for future storage or warranty shipments If it is necessary to store or ship the board please re pack it as nearly as possible in the manner in which it was delivered Special care is necessary when handling or unpacking the product Please consult the special handling and unpacking instruction on the previous page of this manual Page xii ID 1044 0711 Rev 1 0 CP RIO3 05 Preface
17. k Page vi ID 1044 0711 Rev 1 0 CP RIO3 05 Preface 1 1 1 2 1 3 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 List of Figures CP RIO3 05 Functional Block Diagram 1 3 CP RIO3 05 Front Panel ssh 1 4 CP RIO3 05 Board Layout Top View 1 5 D SUB VGA CONE rsa 2 3 Gigabit Ethernet Connectors J6 and J7 2 4 Dual USB Connector J9 eset een 2 5 D Sub COM Connectors J2a COM1 and J3a COMO 2 6 Onboard Serial Port Connectors J2 COM1 and J3 COM2 2 7 GPIO Connector d TU suit Bod eb IEEE on REA MM x NAMUR uU M Rt M MEE 2 9 SATA Connectors Jd and dB tide tipi sa atras qu Pa e DAE Dew 2 10 Rear I O CompactPCI Connectors rJ2 2 11 ID 1044 0711 Rev 1 0 Page vii Preface CP RIO3 05 This page has been intentionally left blank Page viii ID 1044 0711 Rev 1 0 CP RIO3 05 Preface E This document contains information proprietary to Kontron It may not be copied or transmitted by any means disclosed to others or stored in any retrieval system or media without the prior written consent of Kontron or one of its authorized agents Proprietary Note The information contained in this document is to the best of our knowledge entirely correct However Kontron cannot accept liabili
18. locked the CP RIO3 05 is engaged 7 Fasten the front panel retaining screws 8 Connect all external interfacing cables to the CP RIO3 05 as required 9 Ensure that the CP RIO3 05 and all required interfacing cables are properly secured The CP RIO3 05 is now ready for initial operation Page 3 4 ID 1044 0711 Rev 1 0 CP RIO3 05 Installation 3 3 Standard Removal Procedures To remove the CP RIOS 05 proceed as follows 1 Ensure that the safety requirements indicated in Chapter 3 1 are observed Warning Care must be taken when applying the procedures below to ensure that neither the CP RIO3 05 nor system boards are physically damaged by the application of these procedures 2 Ensure that no power is applied to the system before proceeding Warning Even though power may be removed from the system the CP RIO3 05 front panel cables may have power applied which comes from an external source In addition these cables may be connected to devices that can be dam aged by electrostatic discharging or short circuiting of pins It is the responsibility of the system designer or integrator to ensure that appropriate measures are taken to preclude damage to the system or inju ry to personnel which may arise from the handling of these cables con necting or disconnecting Kontron disclaims all liability for damages or injuries resulting from failure to comply with the above Disconnect any interfacing c
19. o the section High Voltage Safety Instructions on the following page Warning ESD Sensitive Device This symbol and title inform that electronic boards and their compo nents are sensitive to static electricity Therefore care must be taken during all handling operations and inspections of this product in order to ensure product integrity at all times Please read also the section Special Handling and Unpacking Instructions on the following page Warning This symbol and title emphasize points which if not fully understood and taken into consideration by the reader may endanger your health and or result in damage to your material Note This symbol and title emphasize aspects the reader should read through carefully for his or her own advantage ID 1044 0711 Rev 1 0 CP RIO3 05 Preface Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements It was also designed for a long fault free life However the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation Therefore in the interest of your own safety and of the correct operation of your new Kontron product you are requested to conform with the following guidelines For Your Safety High Voltage Safety Instructions Warning All operations on this device must be carried out by sufficiently skilled
20. onization TTL Out 15 SCL I C clock EDID I O ID 1044 0711 Rev 1 0 Page 2 3 Functional Description CP RIO3 05 2 1 2 Gigabit Ethernet Interfaces The CP RIO3 05 provides two dual Gigabit Ethernet connectors J6 ETH A ETH B and J7 ETH C ETH D realized as two dual RJ 45 connectors The interfaces provide automatic de tection and switching between 10Base T 100Base TX and 1000Base T data transmission Au to Negotiation Auto wire switching for crossed cables is also supported Auto MDI X Figure 2 2 GbE Connectors J6 and J7 Table 2 2 Pinout of GbE Con J6 and J7 MDI STANDARD ETHERNET CABLE 10BASE T 100BASE TX 1000BASE T vo SIGNAL 1 0 YO SIGNAL J7 ETHC 1 O TX O TX I O BI DA 2 O TX O TX 1 0 BI_DA 3 RX RX YO BI DB 4 I O BI_DC J6 ERES 5 IO BI DC 6 RX RX 1 0 BI_DB 7 I O BI DD 8 I O BI DD Note The Ethernet LEDs have no functionality on the CP RIO3 05 Page2 4 ID 1044 0711 Rev 1 0 CP RIO3 05 Functional Description 2 1 3 USB Interfaces The CP RIO3 05 provides two identical USB interfaces implemented as a dual USB connector J9 USBO USB 1 Both interfaces provide a maximum transfer rate of 480 Mb s for connecting USB devices One USB peripheral may be connected to each port To connect more USB de vices than there are available ports an external hub is required Figure 2 3 Dual
21. or J2 COM1 Pinout PIN SIGNAL DESCRIPTION e 1 DCD Data carrier detect 2 DSR Data send request 3 RXD Receive data 4 RTS Request to send O 5 TXD Transmit data o 6 CTS Clear to send 7 DTR Data terminal ready O 8 RI Ring indicator 9 GND Signal ground 10 NC Not connected Table 2 7 Onboard Serial Port Connector J3 COM2 Pinout 1 0 DESCRIPTION SIGNAL SIGNAL DESCRIPTION 1 0 Not connected NC 1 NC Not connected Not connected NC 2 NC Not connected l Receive data RXD 3 RXD Receive data O Request to send RTS 4 TXD Transmit data o O Transmit data TXD 5 TXD Transmit data o Clear to send CTS 6 RXD Receive data Not connected NC 7 NC Not connected Not connected NC 8 NC Not connected Signal ground GND 9 GND Signal ground Not connected NC 10 NC Not connected Note The RS 232 signals DCD DTR DSR and RI are not supported on the J3 connector Page 2 8 ID 1044 0711 Rev 1 0 CP RIO3 05 Functional Description The CP RIO3 05 module provides one general purpose input output port with five general pur pose inputs and three general purpose outputs The GPIO port is implemented as a 10 pin on board connector J10 2 1 5 General Purpose Input Output Port Note The GPI signals tolerate only 3 3 V signaling and the inputs have internal pull up resistors The GPI and GPO signals support LVT
22. re 22 Saa aaah radica V List of FIg r S libia Vii Proprietary Note sica TEES ix Ade ke u alari Aes ix Environmental Protection Statement senes ix Explanation Or Symbols siii x For YoUr Salty C xi High Voltage Safety Instructions eva d a dao eau RR ea xi Special Handling and Unpacking Instructions xi General Instructions on Usage iaia Xii Two Year Warranty siii UU TT xiii 1 Introduction Ecce 1 3 LT Board OV rVISW scriba balia 1 3 1 2 Board DI SgramsS cuneos dedi 1 3 1 2 1 Functional Block Diagram sciare 1 3 122 F n AAG asia 1 4 123 B ard Layo t 2 usus 1 5 1 3 Technical Specification auus xt i aaro aaa 1 6 14 SlandardsS u Damn uh u pa M aaa 1 7 1 5 Related Publications iride 1 8 2 Functional Description 2 3 2 1 Bogdan 2 3 2 1 1 VGA 2 3 2 1 2 Gigabit Ethernet Interfaces iii 2 4 213 USB InterfaC88S sid bab EF ae c a a a aba aa 2 5 214 GOM EU IL EMT 2 6 2 1 5 General Purpose Input Output Port 2 9 ID 1044 0711 Rev 1 0 Page iii Preface CP RIO3 05 2 1 6 Serial ATA Interfaces nea 2 10 2 1 7 Rear I O Interface on CompactPCI Connector rJ2 2 11 3 VISION aa 3 3 3 1 Safely Hegulr
23. signals are power supply INPUTS to supply the rear I O module with power These pins MUST NOT be connected to any other power source either within the backplane itself or within a rear I O module Failure to comply with the above will result in damage to your board Page 2 12 ID 1044 0711 Rev 1 0 CP RIO3 05 Functional Description Legend for Table 2 10 SATAx Serial ATA port IPx Gigabit Ethernet port VGAx VGA signals COM1x COM1 port corresponds to COMA on the CP3002 RA CP3002 RC COM2x COM2 port corresponds to COMB on the CP3002 RA CP3002 RC PWRx Power Management signals RIO 5V 3 3V Power GPIx General purpose input signal GPOx General purpose output signal ID 1044 0711 Rev 1 0 Page 2 13 Functional Description CP RIO3 05 This page has been intentionally left blank Page 2 14 ID 1044 0711 Rev 1 0 CP RIO3 05 Installation Chapter Installation ID 1044 0711 Rev 1 0 Page 3 1 Installation CP RIO3 05 This page has been intentionally left blank Page 3 2 ID 1044 0711 Rev 1 0 CP RIO3 05 Installation 3 Installation The CP RIO3 05 has been designed for easy installation However the following standard pre cautions installation procedures and general information must be observed to ensure proper installation and to preclude damage to the CP RIOS 05 other system components or injury to personnel 3 1 Safety Requirements
24. tain information relating to the CP RIO3 05 Table 1 4 Related Publications PRODUCT PUBLICATION CompactPCI Systems and CompactPCl Specification 2 0 Rev 3 0 Boards Kontron CompactPCI Backplane Manual ID 24229 All Kontron products Product Safety and Implementation Guide ID 1021 9142 Page 1 8 ID 1044 0711 Rev 1 0 CP RIO3 05 Functional Description Chapter Functional Description ID 1044 0711 Rev 1 0 Page 2 1 Functional Description CP RIO3 05 This page has been intentionally left blank Page 2 2 ID 1044 0711 Rev 1 0 CP RIO3 05 Functional Description 2 Functional Description 2 1 Board Interfaces 2 1 1 VGA Interface The CP RIO3 05 provides one 15 pin D Sub VGA connector J8 on the front panel This connector is used to connect an analog VGA CRT monitor to the CP RIO3 05 The following figure illustrates the D Sub VGA connector J8 Figure 2 1 D Sub VGA Connector J8 The following table indicates the pinout of the D Sub VGA connector J8 Table 2 1 D Sub VGA Connector J8 Pinout PIN SIGNAL FUNCTION ie 1 Red Red video signal output 2 Green Green video signal output 3 Blue Blue video signal output 4 NC Not connected 5 8 GND Signal ground 9 VCC Power 5V 140 mA fuse protection O 10 GND Signal ground 11 NC Not connected 12 SDA I C data EDID I O 13 Hsync Horizontal synchronization TTL Out 14 Vsync Vertical synchr
25. that environmental testing can be destructive when not performed in accordance with the applicable specifications In particular for example boards without conformal coating must not be exposed to a change of temperature exceeding 1K minute averaged over a period of not more than five minutes Otherwise condensation may cause irre versible damage especially when the board is powered up again Kontron does not accept any responsibility for damage to products resulting from destructive environmental testing Rev 1 0 Page 1 7 Introduction CP RIO3 05 In addition modules providing ruggedized service comply with the following standards as well Table 1 3 Additional Standards for Modules Providing Ruggedized Service TYPE ASPECT STANDARD REMARKS Environmental Vibration IEC60068 2 6 Ruggedized version test parameters Sinusoidal 10 300 Hz frequency range 5 g acceleration 1 oct min sweep rate 10 cycles axis 3 axis Single Shock IEC60068 2 27 Ruggedized version test parameters 30 g acceleration 9 ms shock duration half sine 3 number of shocks per direction total 18 6 directions 5 s recovery time Permanent Shock IEC60068 2 29 Ruggedized version test parameters 15 g acceleration 11 ms shock duration half sine 500 number of shocks per direction 6 directions 5 s recovery time 1 5 Related Publications The following publications con
26. ty for any inaccuracies or the consequences thereof or for any liability arising from the use or application of any circuit product or example shown in this document Kontron reserves the right to change modify or improve this document or the product described herein as seen fit by Kontron without further notice Trademarks Kontron the PEP logo and if occurring in this manual CXM are trademarks owned by Kon tron Kaufbeuren Germany In addition this document may include names company logos and trademarks which are registered trademarks and therefore proprietary to their respective owners Environmental Protection Statement This product has been manufactured to satisfy environmental protection requirements where possible Many of the components used structural parts printed circuit boards connectors batteries etc are capable of being recycled Final disposition of this product after its service life must be accomplished in accordance with applicable country state or local laws or regulations ID 1044 0711 Rev 1 0 Page ix Preface CP RIO3 05 Explanation of Symbols A GO Page x Caution Electric Shock This symbol and title warn of hazards due to electrical shocks 60V when touching products or parts of them Failure to observe the pre cautions indicated and or prescribed by the law may endanger your life health and or result in damage to your material Please refer also t
27. utputs CompactPCl One CompactPCI connector rJ2 for connecting the CP RIO3 05 to the backplane Temperature Range Operational 40 C to 70 C Storage 55 C to 85 C Without any additional components Note When additional components are installed refer s to their operational specifications as this will influ o ence the modules operational and storage tem 6 perature Mechanical 3U 8HP CompactPCl compliant form factor Dimensions 100 mm x 80 mm Board Weight 166 g Page 1 6 ID 1044 0711 Rev 1 0 CP RIO3 05 Introduction 1 4 Standards The CP RIO3 05 complies with the requirements of the following standards Table 1 2 Standards TYPE ASPECT STANDARD CE Emission EN55022 EN61000 6 3 Immission EN55024 EN61000 6 2 Electrical Safety EN60950 1 Mechanical Mechanical Dimensions IEEE 1101 10 Environmental Climatic Humidity IEC60068 2 78 see note below WEEE Directive 2002 96 EC Waste electrical and electronic equipment RoHS Directive 2002 95 EC Restriction of the use of certain hazardous sub stances in electrical and electronic equipment re ID 1044 0711 Note Kontron performs comprehensive environmental testing of its products in accor dance with applicable standards Customers desiring to perform further environmental testing of Kontron prod ucts must contact Kontron for assistance prior to performing any such testing This is necessary as it is possible
28. y cause damage to the CP RIO3 05 or result in improper system operation 2 Ensure that the CP RIO3 05 is compatible with the CPU board and the backplane prior to installation 3 If appropriate ensure that the onboard peripheral devices are properly installed prior to installation of the CP RIO3 05 4 Ensure that no power is applied to the system before proceeding Warning Even though power may be removed from the system the CP RIO3 05 front panel cables may have power applied which comes from an external source In addition these cables may be connected to devices that can be dam aged by electrostatic discharging or short circuiting of pins It is the responsibility of the system designer or integrator to ensure that appropriate measures are taken to preclude damage to the system or inju ry to personnel which may arise from the handling of these cables con necting or disconnecting Kontron disclaims all liability for damages or injuries resulting from failure to comply with the above Warning When performing the next step DO NOT push the CP RIO3 05 into the backplane connector Use the ejector handle to seat the CP RIO3 05 into the backplane connector 5 Carefully insert the CP RIO3 05 into the slot designated by the application requirements for the CP RIOS 05 until it makes contact with the backplane connector 6 Using the ejector handle engage the CP RIO3 05 with the backplane When the ejector handle is
Download Pdf Manuals
Related Search