Silver Pulser Product Manual - Silver Pulser by SOTA.
Contents
1. e One 1 Micropulsing Cord e Six 6 Pair Cotton Sleeves One 1 Arm Band and Clip One 1 Neoprene Velcro Wrist Strap e One 1 50 ml Dark Glass Dropper Bottle For Making Ionic Colloidal Silver e One 1 Silver Wire Holder e Two 2 Silver Wires of 9999 4 Nine Purity One 1 Green Scrubber Pad To replace accessories please contact your supplier OPERATIONAL CAUTIONS As with all electrical devices do not use a Near water b When driving a car or c When operating heavy equipment GETTING STARTED 1 Place the 9 Volt Alkaline battery in the unit a On the back of the unit slide off the battery cover 9 Volt b Position the 9 Volt Alkaline battery so the the ceo he 7 ALKALINE positive and negative terminals line up as in the diagram Note The smaller circle on the battery matches the smaller circle in the case the larger The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 2 of 10 www sotainstruments com battery circle matches the larger circle in the case c Slide the 9 Volt Alkaline battery into the case and push down Slide the cover back onto the unit Turn the unit ON by rotating the ON OFF switch clockwise The GREEN light indicates the un2. The Silver Wires are of the highest grade 9999 or 99 99 or 4 Nine pure fine silver Caution When the SOTA pure Silver Wires wear too thin do not replace with sterling silver wire Sterling silver contains nickel which can be toxic Typical Use Quantity There is no definite amount to drink When consumed on a regular basis daily or several times a week it is best to drink no more than 1 to 2 ounces 30 to 60 ml at a time After an extended period of use it is wise to take breaks Strength Laboratory testing indicates lonic Colloidal Silver is effective as low as 2 PPM When ingesting on a regular basis it is suggested to limit the strength to less than 10 PPM CAUTIONS Ingesting larger quantities of lonic Colloidal Silver over a longer period of time could possibly result in argyria Argyria is a darkening of the skin a bluish tinge This occurs when silver molecules are eliminated through the skin and exposed to light Darkening of the moons of the finger nails is usually an early sign of argyria The bluish tinge becomes especially noticeable around the eyes and nose on the face The risk of argyria is considered greater with larger particle sizes When made with a constant current unit using distilled water the particle size remains small so the risk of argyria is considered less The risk of argyria is greater if one is deficient in selenium or vitamin E Drinking Ionic Colloidal Silver for long periods of time is k
3. 1 litre 3 to 4 hours For 1 gallon 16 cups or 4 liters 10 to 12 hours Storage Pour the lonic Colloidal Silver into a dark glass bottle never metal and store in a dark place Over time sunlight or room light will degrade Colloidal Silver by turning the solution grey or black When made and stored properly Ionic Colloidal Silver retains freshness for many weeks It is suggested however that you use as freshly as possible If settling occurs it is losing potency The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 7 of 10 www sotainstruments com Instructions for the Silver Pulser Model SP5 Do not freeze refrigerate or expose Ionic Colloidal Silver to extremes of temperatures as its potency may be affected Do not drink any sediment Save on batteries The unit can be powered by a wall adaptor when making Ionic Colloidal Silver See page 24 for specifications Switch Silver Wire positions The ions of silver come off only one of the wires The silver ions move from the wire in the positive terminal or anode into the water To equalize the wearing of the Silver Wires exchange the position of the wires If left in the same position only one Silver Wire will gradually wear away Purity of the Silver Wires
4. drugs HOW TO USE THE IONIC COLLOIDAL SILVER FUNCTION How To Assemble 1 The Silver Wires fit into the two small holes in the Silver Wire Holder 2 To insert the Silver Wires move the spring clip away from the hole to allow the wire to slide in smoothly Insert 3 Insert as in the picture or it may be easier to insert from Silver Wire the underside of the holder Push the wire through Most of the wire should be below the holder 4 Release the clip to hold the Silver Wire snuggly in place 5 Repeat the above steps for the second Silver Wire and plug the Silver Wire Holder into the Silver Pulser The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 6 of 10 www sotainstruments com Instructions for the Silver Pulser Model SP5 How To Make Ionic Colloidal Silver The Silver Pulser provides a constant current output Constant current allows a very simple procedure for making a high quality Ionic Colloidal Silver as room temperature water can be used 1 Pour two cups 16 ounces or 500 ml of room temperature distilled water into a tall glass or jar Do not use a metal or plastic container Silver Wires 2 Place the Silver Wire Holder on the glass or jar immersing the Silver Wires Keep them at least 25 mm o
5. INSTRUCTIONS FOR SOTA SILVER PULSER MODEL SP5 CONTENTS JE B Ga eS rere rere eee rer reer eee ere eee ee eee ee 1 COMPEEMENT ARY ONE ko teereene eer re errr re E ee E 2 OV EP Tas Te INIT IN GODE sericea teeny sees cg neon cet E cece E E S 2 FERA NONSE CAUTON rura a eee E ee ee 2 GEETING STARTED eee E E E E E EE ee 2 HOW TO USE THE MICROPULSING FUNCTION sessesssessssssesesssssescesresrrsescestesrsseeseseesrsseees 3 How Micropulsing Should Feel oo eee eseesseeseeeseeesceesceescecseecseecssecesecssecssecsaeesaeesseeeaeenaes 5 Aao Core AO reer ene ere ee ee ere ee ee 5 TING E A E esp oesnbeaue audeayeesueratoscedeugeei E cies 5 EO TNS EV DIT ocr esac cesar EN E E saeesyecsopectecsacesseesapepeueeace 6 HOW TO USE THE IONIC COLLOIDAL SILVER FUNCTION oe eeeeseeeneeeeeeeees 6 HOw Fa SUN aca se esca ee ceece cts EE RE E neat 6 Howto Make lomic Colloida SUVE aeeeremrerren te errr ter tenner ater er ten ere ere er ere etree 7 Ey eE E eeepc ceca ae A arte E eae E E E A T 8 CAUTION aaah ee E ea esac ogre ea E o eee ceca te see eu E E E EEEE 8 BF ok Ged Wha God ee bac G4 Wa O28 TION orrea A E E eee eee 8 POWT INOC UEC C1 Soba esta sine trea esnarecestoonaeteamnustetse naeteaearawb ARE A EON 8 Eemal One 6c oh geueerrer ener mn ty renter cere E eee E Tee 9 Output SpeciHCANONS csser naiean ee iaaieo cee eee eee 9 kecrot cape Da E E eee e EEE E E E E eer re eee 9 SUMMAR T OF GE orii aae E E E E 9 TROUBLESHOOTING eiee n EE A E T E ET ee 9 WAR
6. Low Battery Warning FLASHING YELLOW Micropulsing Micropulsing Cord and External Power lonic Colloidal Silver Jack Supply Jack The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 3 of 10 www sotainstruments com 11 12 When finished turn the unit OFF The cotton sleeves will against the skin over the pulse points 10 Turn the unit ON by rotating the ON OFF switch Instructions for the Silver Pulser Model SP5 Place the other cotton sleeve in line with the pulse point on the little finger side of the wrist This pulse point is usually harder to feel It is located in the soft hollow on the wrist in P line with the little finger Press the sleeve to the wrist strap to yr firmly adhere the sleeve in place Once in place the cotton sleeves will stay in the right position for repeated use 6 Take the wrist strap off 7 Insert one electrode from the Micropulsing Cord into each of the cotton sleeves 8 Wet the cotton sleeves with water 9 Put the wrist strap on so the damp cotton sleeves are clockwise Turn the switch slowly until you feel the current If you do not feel the current see Notes on page 14 The flashing YELLow light should come on and get brighter as the in
7. RANTY e E E eee ease E A 10 REPAIR o E tea E E E A E E ieceteeegeae se 10 INTRODUCTION Thank you for allowing us to be a part of your wellness team The Silver Pulser is a consumer product designed to complement a healthy lifestyle This unit has two functions 1 Micropulsing to apply gentle microcurrents 2 Making Ionic Colloidal Silver Please understand that results will vary Healthy lifestyle choices are important Please read this manual carefully We encourage you to become well informed about Micropulsing and Ionic Colloidal Silver To learn more about the Silver Pulser we invite you to visit www sotainstruments com The SOTA Silver Pulser is built to give you many years of trouble free use The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 1 of 10 www sotainstruments com Instructions for the Silver Pulser Model SP5 COMPLEMENTARY UNITS The Silver Pulser offers two parts of a 4 part program 1 The Silver Pulser for Micropulsing 2 The Magnetic Pulser for Pulsed Magnetic Fields 3 The Silver Pulser for making Ionic Colloidal Silver 4 The Water Ozonator for freshly Ozonated Water COMPLETE UNIT INCLUDES e One 1 Silver Pulser Unit e One 1 9 Volt Alkaline Battery For Micropulsing Application
8. TA Products will vary for each person 2009 SOTA Instruments Inc 4 of 10 www sotainstruments com Instructions for the Silver Pulser Model SP5 Low Battery Warning The red light comes on when the battery is low This means the battery will soon need to be replaced The battery can continue to be used until the YELLOW light goes off Power Supply When the Micropulsing Cord is used the jack to plug in a wall adaptor is not accessible With Micropulsing the unit can only be powered by a 9 Volt Alkaline battery How Micropulsing Should Feel 1 The microcurrent should be felt but it is not necessary to turn the intensity control up to an uncomfortable level 2 With repeated use the ability to feel the microcurrents may change It will then be necessary to increase the intensity 3 Twitching of the fingers is normal at a higher intensity Typical Use Alternate wrists daily Length of Session Build up time gradually It is best to start slowly Start with 10 to 20 minutes a day Increase gradually to a minimum of 2 hours each day Length of Use After daily use for 6 to 12 weeks a maintenance schedule is important See page 17 for suggestions Stop Gradually Reduce the amount of time each day for the last week of use If using the 4 part program it is suggested to stop only one part of the protocol at a time Drink plenty of water It s important to drink enough water when using the unit Drinking ozonated water is esp
9. cifications Exceeding the voltage rating may result in injury or unit failure This will void the warranty Output Specifications The output voltage is a nominal 31 Volts Micropulsing Application Frequency through electrodes is 3 92 Hz or 1 2 of the Earth Schumann frequency of 7 83 Hz 1 Hz with a Bi Phasic Square Wave 31 Volts 1 Volt peak per cycle Maximum current through the electrodes is 8 milliamperes into 1 000 ohms 12 milliamperes into a short circuit at 31 Volts peak per cycle Ionic Colloidal Silver Application The maximum current through the Silver Wires is 1 5 milliamperes 0 5 mA at 31 VDC compliance voltage when the Silver Wires are touched together to short the circuit The SP5 is designed and engineered in Canada and made in China Rechargeable Batteries We suggest you purchase a battery charger with NiMH rechargeable batteries When doing so please take the Silver Pulser with you as some rechargeable batteries are too large for the enclosure This way you will be sure to purchase batteries that fit SUMMARY OF LIGHTS GREEN light Indicates the unit is on RED light Indicates the battery is low and will soon need replacing YELLOW light Indicates the Micropulsing function is in operation ORANGE light Indicates the Ionic Colloidal Silver function is in operation TROUBLE SHOOTING Test to determine if Micropulsing Cord needs replacing If the YELLow light does not come on and the micro
10. currents cannot be felt replace the 9 Volt Alkaline battery and turn the unit ON If the problem persists 1 Buff the electrodes lightly to ensure good electrical contact 2 Plug in the Micropulsing Cord Turn the unit ON and touch the electrodes together The yellow light should come on and flash Turn up the intensity and the flashing yellow light should get brighter The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 9 of 10 www sotainstruments com Instructions for the Silver Pulser Model SP5 This tests both the Silver Pulser output and the Micropulsing Cord If the light does not come on the Micropulsing Cord may need replacing If current is not felt check to ensure that the inside of the wrist strap is not wet If wet the current is being shorted rather than entering the skin WARRANTY The Silver Pulser model SP5 is covered by a three 3 year limited warranty Please keep proof of purchase Warranty is void if the failure is due to abuse or negligence SOTA reserves the right to make changes to the Silver Pulser without notification REPAIRS Please contact your supplier for return instructions Or for information about your closest repair depot contact repairs sotainstruments com Tel 1 250 770 2023 Fa
11. ecially helpful Maintenance Schedule Ongoing use may be beneficial Suggestions for a maintenance schedule are a once weekly b one week per month or c 4 weeks every six months CAUTIONS 1 Do not place the Micropulsing electrodes over skin lesions abrasions new scars cuts eruptions or sunburn 2 Do not use if the Micropulsing suddenly feels different or prickly and the YELLow light stops flashing Turn the unit off immediately and contact SOTA Instruments 3 The body may absorb nutrients and substances more readily when Micropulsing This is a plus with healthy nutrients but it is best to avoid coffee alcohol synthetic supplements or excess sweets Also avoid cigarettes and nicotine products Do not use with prescription drugs 4 Do not apply the bare electrodes to the skin 5 Keep the cotton sleeves damp Both dry sleeves and bare electrodes will cause an electrical burn which may scar 6 Do not sleep while using the Micropulsing electrodes as the sleeves may dry out This could result in an electrical burn The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 5 of 10 www sotainstruments com Instructions for the Silver Pulser Model SP5 7 During the first weeks of use the skin may become irritated Ove
12. it is ON If the light does not come on the battery may not be placed correctly Turn the unit OFF by rotating the ON OFF switch counter clockwise until it clicks Important Do not force the ON OFF switch past its natural stopping point HOW TO USE THE MICROPULSING FUNCTION 1 Clean the wrist area to remove oils from the skin This will allow for better conductivity Insert the Micropulsing Cord into the jack on the unit as in the diagram The indented square on the din plug should be facing up When the plug is positioned correctly it will slide in gently Do not force Slide the on the back of the Silver Pulser into the holding 3 clip on the Arm Band as in the diagram in place pocket A longer Micropulsing Cord is needed for this option To position the cotton sleeves on the wrist strap place the Velcro side of the wrist band face out rather than towards the skin Attach one cotton sleeve to the wrist band in line with the pulse point on the thumb side of the wrist Press the sleeve to the wrist band to firmly adhere the sleeve in place 4 Slide the Arm Band with the unit and cord up the arm to a comfortable position Tighten the band to secure it Option If preferred the unit can be placed in a Instructions for the Silver Pulser Model SP5 ON OFF Switch and INTENSITY Control me ORANGE lonic Colloidal Silver A SILVER PULSER GREEN Power RED
13. nown to deplete selenium and vitamin E In addition to taking breaks from ingesting Ionic Colloidal Silver it may be wise to supplement with these two nutrients With proper supplementation and the use of Far Infrared saunas it may be possible to reverse or remove the bluish tinge of argyria ELECTRICAL SPECIFICATIONS Power Requirements When the battery needs replacing use only a 9 Volt Alkaline battery The wall adaptor that comes with other SOTA units can be used for making Ionic Colloidal Silver A wall adaptor cannot be used with the Micropulsing function Micropulsing requires a 9 Volt Alkaline battery The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 8 of 10 www sotainstruments com Instructions for the Silver Pulser Model SP5 External Power Supply With an additional attachment a Universal Power Cord with tip positive from an electronic store the Silver Pulser can also be operated from a 12 Volt DC automobile battery or an appropriate Solar Panel To use a wall adaptor for making Ionic Colloidal Silver the output should be from 6 to 12 Volts DC with a positive centre pin and a minimum of 500 mA milliamperes of current CAUTION Do not use a wall adaptor with a negative centre pin or incorrect electrical spe
14. r 1 inch from the bottom of the container 3 Turn the unit ON by rotating the ON OFF switch clockwise It is not necessary to turn up the intensity Allow it to operate for 1 5 to 2 hours The oranc light will brighten as the current increases up to the 1 5 mA limit 4 Stir occasionally with a non metal utensil Occasionally wipe off the grey or black silver oxide that builds up on the Silver Wires 5 Two cups 16 ounces or 500 ml for 2 hours will produce a 5 to 8 PPM batch of Ionic Colloidal Silver depending on the brand of distilled water The concentration of silver is measured in Parts Per Million or PPM Note Do not add salt or heat the water to try to decrease the time required With constant current the time required to produce 5 PPM or more will not be reduced by trying to increase the conductivity of the water 6 When finished wipe the Silver Wires with paper towel to remove residue Buff lightly when needed to keep them free of sediment Harsher buffing will wear away the silver Notes Color Ionic Colloidal Silver remains clear to about 5 or 6 PPM Ata slightly higher PPM it will be a pale gold color Do not drink if it is darker than pale gold as this indicates a higher level of impurities or larger particle sizes To Make Larger Quantities The Silver Pulser can be used to make larger quantities of Ionic Colloidal Silver For a concentration between 5 to 8 PPM use the following times as a guide For 4 cups or
15. r time irritation usually decreases or disappears Alternating wrists each session allows any irritation to better heal Sensitive Skin Some individuals may be particularly sensitive to microcurrents and the irritation may continue To ensure the current is felt 1 Wet the sleeves with purified water or Ionic Colloidal Silver The silver solution has a healing effect 2 If unable to feel the current try a commercial saline solution for the eyes This is gentler than adding salt to the water 3 A conductive gel can also be added to the wet sleeves to reduce irritation 4 Another option is to wrap a small square of paper towel around the electrodes instead of using cotton sleeves There may be fewer impurities in the paper than the cotton Keep the paper wet A small square of paper towel may last for several applications To minimize irritation 5 Wash wrists well after each session and apply a healing gel or lotion such as aloe vera vitamin E oil or MSM cream 6 Drink enough water to keep the body well hydrated The level of hydration may affect sensitivity 7 Apply the Micropulsing electrodes for shorter periods of time until the irritation disappears Do not use the Micropulsing function in the following situations as safety has not been explored In the case of pregnancy nursing or trying to get pregnant e With a pacemaker or other active implanted device If taking a pharmaceutical drug or any recreational
16. tensity is turned up If the flashing YELLOW light does not come on the electrical path has not been established See Troubleshooting on page 31 TAM w a oOo Mh remain correctly positioned for the next session 13 Clean the wrist and apply a healing lotion to avoid irritation Notes Suggestions for Feeling the Current If the current is not felt with wet cotton sleeves prepare a mild salt solution to wet the sleeves Add only a few grains of salt to the water in the 50 ml dropper bottle A commercial electrolyte gel can also be used instead of a salt solution Care of Micropulsing Electrodes Discoloration of electrodes is normal Buff occasionally to ensure good electrical contact Care of Cotton Sleeves Wash or rinse sleeves after use Discard and replace cotton sleeves periodically Alternatives to Cotton Sleeves The following items can be used in place of the cotton sleeves a Unbleached Paper Towel Cut a small square of paper towel large enough to wrap around the electrode 2 or 3 times Moisten prior to use b Cotton Flannel Cut a small square of cotton flannel and wrap around the electrode with thread Moisten prior to use The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SO
17. x 1 250 770 1999 RoHS m compliant The SOTA units are consumer products for general health and well being The use safety or effectiveness of the SOTA units has not been approved by any government agency Results using the SOTA Products will vary for each person 2009 SOTA Instruments Inc 10 of 10 www sotainstruments com
Download Pdf Manuals
Related Search