K-SERIES TV LIFT ECO-VERSION User Manual
Contents
1. K SERIES TV LIFT ECO VERSION User Manual List of contents Required tools l Horizontal beam 1 pc 3 Vertical beam 2 pcs Mounting bracket Control box Remote Screws Allen key 4 iit hit A EY AAA WW Woodscrew 4x16 Woodscrew 5x16 Lift assembly 1 Level cabinet to be sure that it is standing stably on the floor 2 Place column in the middle of cabinet Pic 1 Pic 1 3 Use provided mounting bracket and attach column to the side of the cabinet Pic 2 Woodscrew max 5x15 Lit SN ANS Mounting bracket a ounting bracke Ny ig a ae i 5 N T Re f s hp f i Woodscrew max 4x15 gt Po FL h T UD Li r fl Ur Pic 2 4 Attach base of the lift to the bottom of your furniture with woodscrews Pic 2 5 Using attached screws mount horizontal beam to the column Pic 3 OTXIN OBELOSI DEXON O8tZOS Pic 3 6 Connect control box to the lift as on Pic 4 Pic 4 7 Using 4 pcs of woodscrews hang control box as on Pic 5 There s no need to mount control box to the side Leave about 0 5 mm to have possibility to hang control box easily Pic 5 Assembly of TV screen to the lift 8 Using screws provided by your TV manufacturer mount the vertical beams to your screen The beams should be about 1 inch below u2. e The second short press on SETUP button caused faster movement of lift When you have set your preffered position press amp hold the SETUP button for about 3 seconds until you will hear two short beeps and the red SETUP light is down The viewing position is now set Remote Control assignment To assign the remote control Press the RC SET button and then press any button and hold one of the remotes buttons for about 1 second If the remote is assigned you will hear a short beep ATTENTION The remote assignment mode is active for about 30 seconds after pressing amp holding the RC SET button If the signal from the remote is not received during this time the control box will quit the remote assignment mode Safety system The contorl box monitors the energy consumption of your screen After exceeding allowed current of motor allowed load of lift control box cuts the power out and lift stops After the obstacle iss removed lift is ready for working Display messages The numeric display shows the information about the lift operation If the display shows e _ 0 Blinking electric motor overload current exceeded e 17 Blinking inactive function e 2 Blinking power cut out when hiding the active screen e 32 Blinking wiring loom not connected to the control box e 4 Blinking lower limit switch activated e 57 Blinking upper limit switch activated Pressing any button will delete the display mes
3. pper edge of the screen Pic 6 ist re Pic 6 9 Loosen the lower brackets on the vertical beams as shown on Pic 7 Pic 7 10 Hang the screens with vertical beams mounted on the horizontal beam on your lift Pic 8 For easier assembly you can move up lift see in control box manual Pic 8 11 Move the lower brackets on the vertical beam up and tighten the screws Pic 9 Pic 9 12 Remember to connect all cables to the TV when lift is draw aside You will be sure that cables have enough length Pic 10 Pic 10 13 For the final assembly mount the top lid of your furniture on the hinges CONTROL BOX MANUAL K ECO LIFT Programming the VP Viewing Position ATTENTION You have to set the VP if you want all of the lifts functions to work properly To set the VP follow this procedure Press amp Hold the SETUP button for about 3 seconds until the red SETUP light is lit You are now in the programming mode Press amp Hold the UP Or DOWN button to set the preffered position You can change the movement speed in the setup mode by pressing the SETUP button once There are 2 movement speeds ATTENTION Two movement speeds are available in SETUP mode slow and fast
4. sage
Download Pdf Manuals
Related Search