Illusion Dotz 4.4
Contents
1. 4 Either 540 or 630 will be displayed use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit FEEDBACK With this function you can feedback switch the pan movement or tilt movement 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until Feedback is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit MOVEMENT SPEED With this function you can set the pan and tilt ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 16 Illusion Dotz 4 4 System Menu movement speed 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until Move Speed is displayed and press ENTER 4 Either Speed 1 Speed 2 Speed 3 or Speed 4 will be dis played use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit MIC SENS With this function you can2. EXAMPLE If you want the address to be 57 you must first set the address that is currently assingned to the unit Then set Channel 1 s ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 14 Illusion Dotz 4 4 System Menu value to 7 Channel 2 s value to 7 and Channel 3 s value to 57 Wait 20 seconds and the address should change on the unit to 57 2ND EXAMPLE If you want the address to be 420 you must first set the address that is currently assingned to the unit If you want the set the address to 420 set Channel 1 s value to 7 Channel 2 s value to 8 and Channel 3 s to 164 256 164 420 NO DMX STATUS With this function if the DMX signal is suddenly lost the unit will automatically go into 1 of 4 modes 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until No DMX Status is displayed and press ENTER 4 Either Hold Last DMX setting Close Blackout Music Sound Active or Auto Auto Program will be displayed use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit PAN INVERT With this function you can reverse the Pan movement 1 Press the MODE button to
3. ENTER 2 Press the UP or DOWN buttons until Calibration is displayed press ENTER 3 XXXX will be displayed The password is 050 4 Press ENTER to confirm or press MODE to exit PROGRAM The fixture comes equipped with a built in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board Programs can be created and stored using the fixture s control board or by using an external DMX controller 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Program is highlighted then press ENTER 2 Use the UP or DOWN buttons to find and access one of the below submenus Select Program This function allows the user to select one of ten of the user defined built in programs This program is then accessed in Function Mode under Program Run Edit Program This function allows the user to edit the built in pro grams Edit Scene This function allows the user to edit or define the actual scenes that are stored in the user defined built in programs that are accessed in the previous step Scene Input The Illusion Dotz 4 4 features an integrated DMX recorder Preprogrammed scenes can be transmitted to the fixture via any DMX compliant controller This function allows those scenes to be stored in to the fixture s built in memory and then subsequently used to create the user defined programs ADJ Products L
4. Kling Net Artnet 2 Install one of the recommended operating softwares onto your computer Recommended softwares Arkaos Media Master Express Media Master Pro or LED Master Sold Separately 3 Connect the panels via CAT 5 Straight Network cable When creating your own custom cable use RJ45 Straight Network cable 4 Map the fixtures using KlingNetMapper or Art Net Mapper 5 Control the fixtures using ArKaos or Art Net software Please refer to the media playback software user manual for further instruc tions Note ArKaos Kling Net requires a gigabit 1000 mbps Ethernet card and network router for a smoother operation Installation method 1 A Kling Net Art Net Standard CAT SO RJ45 LED LIGHTING ees LED LIGHTING Standard CAT Cable Standard CAT Cable ee LED LIGHTING Standard CAT Cable Note Do not daisy chain more thean 25 units when connected directly from the computer Use a Ethernet Switch if more than 25 units are being controlled When connecting you must use a CAT 5 Straight Network cable Installation method 2 k Kling Net Art Net x Standard CAT Cable Kling Net Art Net Standard CAT Cable j R445 LED LIGHTING N FIRJA5 LED LIGHTING EJRJ45 LED LIGHTING Standard CAT Cable Standard CAT Cable Standard CAT Cable 3 Kling Net Art Net Standard CAT Cable j R445 LED LIGHTING FIRJA5 LED LIGHTING FJRJA5 LED LIGHTING Standard CAT Cable Stan
5. D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands E PEE AEE service adjgroup eu www adj eu youtube com adjlighting Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On HOM facebook com americandj
6. Init Effect INIT EFFECT In this menu you are able to check initial effect posi tion 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press UP or DOWN buttons until Init Effect is displayed and press ENTER 3 XXX will be displayed XXX represents the current effect posi tion 4 Press ENTER or press MODE to exit CHANNEL VALUE This function will allow you to see the DMX value of each DMX channel that is currently being used at the time 1 Access the main menu and press the UP or DOWN buttons so ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 23 Illusion Dotz 4 4 that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until DMX Value is displayed and press ENTER 3 A DMX Channel will be displayed Example Prism Color Wheel Gobo Wheel etc Press ENTER when you find the DMX channel that you would like to check When you press ENTER the DMX value of that channel will displayed 4 Press the MODE button to exit System Menu SLAVE SET This function lets you designate the unit as the slave in a Master Slave configuration 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Slave Set is displayed and press ENTER 3 Either Sl
7. LCD Set is displayed press ENTER 3 Press UP or DOWN buttons until DispFlash is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit Dimmer Curve DIM CURVE Select 1 of 5 dimming curves See page 45 for the dimming curve chart ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 22 Illusion Dotz 4 4 System Menu 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Dim Curve is displayed press ENTER 3 Either Standard Stage TV Architectural or Theater will be displayed use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit Temp C F TEMP C F With this function you can change the temperature dis play to show either Celsius or Fahrenheit 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press UP or DOWN buttons until Temp C F is displayed and press ENTER 3 Either Celsius or Fahrenheit will be displayed use the UP and DOWN buttons to toggle between 4 Press ENTER to confirm your selection or press MODE to exit
8. a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse Illusion Dotz 4 4 Cleaning Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp out put 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing Use a brush to wipe down the cooling vents and fan grill Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in Illusion Dotz 4 4 Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions oN No light output from the unit 1 Be sure the external fuse has not blown The fuse is located on the bottom panel of the unit 2 Be sure the fuse holder is completely and properly seated Unit does not respond to sound 1 Low frequencie
9. or exhibits a marked change in performance ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 4 Illusion Dotz 4 4 Features 3 Modes of DMX 512 Protocol Compatible 12 DMX Channel Mode 14 DMX Channel Mode and 59 DMX Channel Mode RDMX Lets you set the DMX address from any DMX Controller 3 Operating Modes Master Slave Stand Alone Sound Active Kling Net and Art Net Compatible Recommended control solu tions Arkaos Media Master Express Media Master Pro and LED Master software s sold separately Internal Microphone 5 Dimmer Curve Settings Power Cord Daisy Chaining See below Edit and Save Scenes into the Memory 360 540 Pan Movement 270 Tilt Movement Digital Display for Address and Function Setting Illusion Dotz 4 4 Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the PowerCON input and output sockets The quantity that can be connected is 3 fixtures maximum for 120V and 5 fix tures maximum for 240V After the maximum fixtures has been reached you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 5 Illusion Dotz 4 4 General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain impor
10. set the microphone sensitiv ity The default setting is 70 You can adjust the sensitivity between 0 99 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until Mic Sensitivity is displayed and press ENTER 4 Use the UP and DOWN buttons to adjust the mic sensitivity between 0 99 5 Press ENTER to confirm your selection or press MODE to exit STAND BY With this function the LEDs and step motors will power off if there is no DMX signal within 15 mins factory defualt Once it receives a DMX signal the fixture will reset itself 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until Stand By is displayed and press ENTER ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 17 Illusion Dotz 4 4 System Menu 4 15M will be displayed use the UP and DOWN buttons to adjust the hibernation period between 01M 99M or Off 5 Press ENTER to confirm your selection or press MODE to exit Fixture ID SERVICE PIN With this function you can enter the RDM password so that you can access and change
11. the RDM ID number 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Fixture ID is displayed press ENTER 3 Press UP or DOWN buttons until Service PIN is displayed and press ENTER 4 The Password is 050 5 Press ENTER or press MODE to exit RDM PID RDM stands for Remote Device Management This feature lets you control every aspect of your fixture remotely from an RDM controller Manual settings like adjusting the DMX address are no longer needed This is especially useful when the unit is installed in a remote area In this submenu you can see the units RDM ID number and adjust it as well 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Fixture ID is displayed press ENTER 3 Press UP or DOWN buttons until RDM PID is displaved and press ENTER 4 XXXXXX will be displayed XXXXXX represents the units current RDM ID 5 Press ENTER or press MODE to exit ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 18 Illusion Dotz 4 4 Svstem Menu DEVICE IP ADDR With this function vou set the Device IP address 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Functio
12. 1 190 PROGRAM 19 OCH See ei E e AGG 191 200 PROGRAM 20 Full LEDs 47700 19200 9700 5410 3540 201 210 PROGRAM 21 3 211 220 PROGRAM 22 221 230 PROGRAM 23 2 231 240 PROGRAM 24 241 250 PROGRAM 25 2 251 255 GRADIENT EFFECT S o je PROGRAM SPEED S SLOW FAST 4 PAN TILT MOVEMENT SPEED fa 0 225 MAX TO MIN SPEED 2 226 235 BLACKOUT BY MOVEMENT 246 255 NO FUNCTION E LAMP ON OFF RESET amp PROGRAMS is Sc SE ee d e a 7 NORMAL C aaa Bs de ALL SE RESET Illusion Dotz 4 4 Dimmer Curve Chart 85 96 NO FUNCTION Dimmer 97 99 OTHER MOTOR RESET 100 119 INTERNAL PROGRAM 1 e pere 120 139 INTERNAL PROGRAM 2 140 159 INTERNAL PROGRAM 3 e i 160 179 INTERNAL PROGRAM 4 st 180 199 INTERNAL PROGRAM 5 i 200 219 INTERNAL PROGRAM 6 220 239 INTERNAL PROGRAM 7 E 240 255 SOUND ACTIVE PROGRAM b ker ms Sege o TT 0S Fade Time A d TE 48 Fade Time Trise ms Teom ms Trse ms Teow ms Standard 0 0 0 0 Stage 780 1100 1540 1660 TV 1180 1520 1860 1940 Architectural 1380 1730 2040 2120 Theatre 1580 1940 2230 2280 ADJ Products LLC www adj com ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 44 Illusion Dotz 4 4 Instruction Manual Page 45 Illusion Dotz 4 4 Fuse Replacement Fuse Replacement Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert
13. 9 14 User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use Thank
14. C shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No w
15. E e Restore factorv set ON OFF Time Info Current Power on running time Hours Total Time Fixture running time Hours Last Clear Fixture Last times clear Hours 5 Timer PIN Timer Password ES Clear Last Password 050 E ON DEE ZS Temp Info Head Temp Temperature in the head E Error Info Pan Tilt Reset the error message Model Info Ton Lamps Model Information Software V 1U01 V1 00 Software version information of 2U01 V1 00 each IC Reset M Pan amp Tilt Reset Pan Tilt Test Chan PAN c Test funetion E Panel Ctrl PAN XXX Adjustment of the lamp SZ E E Password Calbrate and adjust the effects to Calibrate PAN standard position Password 050 Select Dro Pro Part 1 Program 1 9 Program 1 Select programs to be run Pro Part 2 Program 1 rr Pro Part 3 Program 1 gro Edit Pro Program 1 Program Test Testing program S Step 01 SCxxx Program in loop E Program 9 Step 64 SCxxx Save and exit Edit Sce Edit Scene 001 Pan Tilt Manually enter the scene Edit Scene 250 Fade Time Fade Time Secne Time Secne Time Input Bv Outside External console scene input Sce Input XX XX Automatic recording scene ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 12 Illusion Dotz 4 4 System Menu The main menu is accessed by pressing the MODE button Browse through the menu by using the UP DOWN RIGHT amp LEFT buttons Press the ENTER button to access the desired menu You can s
16. EMENT NO FUNCTION LAMP ON OFF RESET amp PROGRAMS 0 79 NORMAL 80 84 ALL MOTOR RESET 85 96 NO FUNCTION 97 99 OTHER MOTOR RESET 100 119 INTERNAL PROGRAM 1 120 139 INTERNAL PROGRAM 2 140 159 INTERNAL PROGRAM 3 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 35 0 225 226 235 246 255 Illusion Dotz 4 4 12 Channel DMX Mode Illusion Dotz 4 4 14 Channel DMX Mode Function KEE 160 179 INTERNAL PROGRAM 4 PAN MOVEMENT 8bit 180 199 INTERNAL PROGRAM 5 PAN FINE 16bit 200 219 INTERNAL PROGRAM 6 TILT MOVEMENT 8bit 220 239 INTERNAL PROGRAM 7 TILT FINE 16bit 240 255 SOUND ACTIVE PROGRAM ALL RED 0 100 ALL GREEN 0 100 ALL BLUE 0 100 SHUTTER amp STROBE LED S OFF LED S ON STROBING SLOW FAST LED S ON PULSE EFFECT IN SEQUENCES LED S ON RANDOM STROBE SLOW FAST LED S ON DIMMER CURVES STANDARD STAGE TV ARCHITECTURAL THEATRE DEFAULT TO UNIT SETTING AUTO PROGRAMS PROGRAM 1 PROGRAM 2 PROGRAM 3 PROGRAM 4 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 36 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 37 Channel Value Function Function TT AUTO PROGRAMS LAMP ON OFF RESET amp PROGRAMS PROGRAM 1 97 99 OTHER MOTOR RESET PROGRAM 2 100 119 INTERNAL PROGRAM 1 PROGRAM 3 120 139 INTERNAL PROGRAM 2 PROGRAM 4 140 159 INTERNAL PROGRAM 3 PROGRAM 8 160 179 INTERNAL PROGRAM 4
17. LC www adj com Illusion Dotz 4 4 Instruction Manual Page 30 Illusion Dotz 4 4 Operation Universal DMX Control This function allows you to use a uni versal DMX 512 controller such as the Elatione DMX Operator or Elatione Show Designer to control head movement RGB colors master dimmer shutter strobe and various other features A DMX controller allows you to create unique programs tailored to your indi vidual needs 1 The Illusion Dotz 4 4 has a 12 Channel mode 14 Channel mode and 59 Channel mode See pages 34 44 for detailed description of the DMX traits 2 Tocontrol your fixture in DMX mode follow the set up procedures on pages 13 15 as well as the set up specifications that are included with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the directions on page 36 to select your DMX Channel mode and follow the instruction on page 17 to set the DMX address 6 For longer cable runs more than a 100 feet use a terminator on the last fixture 7 For help operating in DMX mode consult the manual included with your DMX controller Oi teg Stand Alone Sound Active or Auto Program This mode allows a single unit to run to the beat of the music or run through a built in program AUTO PROGRAM 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press EN
18. PROGRAM 9 180 199 INTERNAL PROGRAM 5 PROGRAM 10 200 219 INTERNAL PROGRAM 6 PROGRAM 11 220 239 INTERNAL PROGRAM 7 PROGRAM 12 240 255 SOUND ACTIVE PROGRAM PROGRAM 13 PROGRAM 14 PROGRAM 15 PROGRAM 16 PROGRAM 17 PROGRAM 18 PROGRAM 19 PROGRAM 20 PROGRAM 21 PROGRAM 22 PROGRAM 23 PROGRAM 24 PROGRAM 25 GRADIENT EFFECT PROGRAM SPEED SLOW FAST PAN TILT MOVEMENT SPEED MAX TO MIN SPEED BLACKOUT BY MOVEMENT NO FUNCTION LAMP ON OFF RESET amp PROGRAMS NORMAL ALL MOTOR RESET NO FUNCTION ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 38 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 39 IIlusion Dotz 4 4 59 Channel DMX Mode Illusion Dotz 4 4 59 Channel DMX Mode Value Function Value Function p RED 6 0 255 0 100 GREEN 6 0 255 0 100 BLUE 6 0 255 0 100 0 255 0 100 GREEN 1 RED 7 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 re GREEN 10 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 0 255 0 100 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Pag
19. TER 2 Press the UP or DOWN buttons until Disp Set is displayed and press ENTER 3 Press the UP or DOWN buttons until Auto Pro is displayed and press ENTER 4 Either Master or Alone will be displayed Using the UP or DOWN buttons select Alone and press ENTER SOUND ACTIVE 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Disp Set is displayed and ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 31 Illusion Dotz 4 4 Operation press ENTER 3 Press the UP or DOWN buttons until Sound Ctrl is displayed and press ENTER 4 Either Master or Alone will be displayed Using the UP or DOWN buttons select Alone and press ENTER Master Slave Operation Sound Active or Auto Program This function will allow you to link up to 16 units together and oper ate without a controller The units can run a built in program or run in sound actiive mode In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units pro grams Any unit can act as a Master or as a Slave 1 Using standard XLR microphone cables daisy chain your units together via the XLR connector on the rear of the units Remem ber the Male XLR connector is the input and the Female XLR connector is the output The first unit in the cha
20. access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until Pan Invert is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit TILT INVERT With this function you can reverse the Tilt movement 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 15 Illusion Dotz 4 4 System Menu 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until Tilt Invert is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit PAN DEGREE With this function you can change the pan degree from 630 to 540 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until Pan Degree is displayed and press ENTER
21. active or under DMX control The Illusion Dotz 4 4 can be used as a stand alone unit or in a master slave con figuration For best results use fog or special effects smoke to enhance the beams projections Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2610 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all times ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 3 Illusion Dotz 4 4 Safety Precautions For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or brea
22. address setting User Mode Standard User s mode to change channel Basic numbers g Extend g User A User B S User C gt Edit A Max Channel Preset User modes Edit B PAN Edit C A Status Remote Add ON OFF Add via DMX No DMX Status Blackout GId Auto Sound Auto run if no DMX Pan Invert on OFF Pan Reverse movement Tilt Invert on OFF Tilt Reverse movement Pan Degree 630 540 Pan Degree Select Feedback GN OFF Movement Feedback switch Move Spd Speed 4 Movement Mode Select Mie Sons 0 99 Sensitivity of Mic Stand By OFF 01M 99M SM Stand By Mode Fixture ID Service PIN Password XXX Service Code 050 RDM PID Xxxxax RDM Unique PID setting Device IP Addr EES Set the Device IP address Ctrl IP Addr XXX XIX XXX XXX Set the Console IP address Universe es Port number Protocol Set Kling Net Default Kling Net ArtNet Net Switch ON OFF Ethernet Switeh D Fan Set Head Fan Auto Fans Speed Mode Select 2 High S Low f Base Fan 50 75 95 LCD Set Backlight 02 60m 05m Display shutoff time Flip Display Gi Display Flip 180 Key Lock ON OEE Key Lock DispF lash Display flashes when NoSignal Dim Curve Standard Stage TV Architectural Theater Temp C F Celsius Temperature switch Fahrenheit between CT Init Effect PAN XXX Initial effect position Disp Set Chan Value PAN Value of channel is displayed Slave Set Slavel Slave2 Slave3 Slave receive location choice Auto Pro Master Alone Auto program Sound Ctrl Master Alone Music control DFS
23. amp fails see next page Never use the carrying handles for secondary attachment ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 7 Illusion Dotz 4 4 Mounting NOTICE The suitable enviromental temperature for this light ing fixture is between 25 C to 45 C Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above This will allow the fixture to run at its best and help prolong the fixture life Clamp Quickly locked Safety rope hole Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the Illusion Dotz 4 4 Tighten the quick lock fasteners fully clock wise Install the second Omega holder Pull the safety cable through the holes on the bottom of the base and over the truss ing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 8 Illusion Dotz 4 4 Set Up Power Supply The ADJ Illusion Dotz 4 4 contains a electronic volt age switch which will auto sense the voltage when it is plugged into the power source With the electronic ballast you do not need to worry about wall voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used
24. arranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Dav Limited Warranty e L ED Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1
25. ave 1 Slave 2 or Slave 3 will be displayed Press ENTER to select either of the three or press MODE button to exit AUTO PROGRAM This function allows the internal programs to run in either stand alone or master slave mode In Master mode the fixture will send DMX data to other fixtures connect via the DMX chain In Alone mode the fixture will operate as a single fixture The program for this mode is selected in the Select program section of the control menu You can set the number of steps under Edit pro gram You can edit the individual scenes under Edit scenes With this function you can run the individual scenes either automatically i e with the adjusted Step Time 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Auto Program is displayed and press ENTER 3 Either Master or Alone will be displayed 4 Press ENTER to to make your selection or press MODE button to exit ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 24 Illusion Dotz 4 4 System Menu SOUND CONTROL With this function the internal program will run in sound active mode 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Sound Control is dis played press ENTER 3 Eithe
26. by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Illusion Dotz 4 4 can be controlled via DMX 512 pro tocol The Illusion Dotz 4 4 can be either a 12 14 or 59 channel DMX unit The DMX address is set
27. croll through the submenus using the UP DOWN RIGHT 8 LEFT buttons To confirm every selection press the ENTER button You can exit every menu and submenu by pressing the MODE button The unit will automatically exit the menus if no buttons are pressed after 10 sec onds These next pages will explain each function in the menu layout located on the previous page RECEIVE SET ADDRESS With this function you can adjust the desired DMX address via the Control Board 1 Access the main menu and press the UP or DOWN buttons so that Receive is higlighted then press ENTER 2 Set Address will be displayed press ENTER The current DMX address will now be displayed 3 Use the UP or DOWN buttons to adjust the DMX address 4 Press ENTER to confirm or press MODE to return to the main menu USER MODE USER MODE 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that User Mode is highlighted then press ENTER 2 Press the UP or DOWN buttons until User Mode is displayed press ENTER 3 Use the UP or DOWN buttons to scroll through the 3 DMX Channel Modes Standard Mode This is 14 Channel Mode Basic Mode This is 12 Channel Mode Extended Mode This is 59 Channel Mode 4 Press the MODE button once to return to the User Mode menu ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 13 Illusion Dotz 4 4 System Menu Use the UP or DOWN b
28. d or High Fand Speed will be displayed use the UP and DOWN buttons to ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 20 Illusion Dotz 4 4 System Menu toggle between 4 Press ENTER to confirm your selection or press MODE to exit BASE FAN With this function you can adjust the speed of the base fans 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Base Fan is displayed press ENTER 3 Either Auto Fan Speed default Low Fan Speed or High Fand Speed will be displayed use the UP and DOWN buttons to toggle between 4 Press ENTER to confirm your selection or press MODE to exit LCD Setting BACKLIGHT With this function you can have the LCD display after 2 60 minutes Use this function to adjust the time 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until LCD Set is displayed press ENTER 3 Press UP or DOWN buttons until Backlight is displayed and press ENTER 4 05m 5 minutes will be displayed use the UP and DOWN but tons to adjust the shutoff time between 02m 60m or Off 5 Press ENTER to confirm your selection or press MODE to exit FLIP DISPLAY With this function you can r
29. dard CAT Cable Standard CAT Cable yous DURO Note 1 The Ethernet Switch must be Gigabit Switch 2 Do not daisy chain more than 25pcs units from a single network port of the Ethernet Switch 3 Maximum 2 output network ports of the Ethernet Switch can be used So the system can control 25pes maximum When connecting you must use a CAT 5 Straight Network cable ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 33 Illusion Dotz 4 4 12 Channel DMX Mode Function ALL RED 0 100 ALL GREEN 0 100 ALL BLUE 0 100 SHUTTER amp STROBE LED S OFF LED S ON STROBING SLOW FAST LED S ON PULSE EFFECT IN SEQUENCES LED S ON RANDOM STROBE SLOW FAST LED S ON DIMMER INTENSITY 0 100 DIMMER CURVES STANDARD STAGE TV ARCHITECTURAL THEATRE DEFAULT TO UNIT SETTING PROGRAM 1 PROGRAM 2 PROGRAM 3 PROGRAM 4 PROGRAM 5 PROGRAM 6 PROGRAM 7 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 34 Channel Value Function AUTO PROGRAMS PROGRAM 8 PROGRAM 9 PROGRAM 10 PROGRAM 11 PROGRAM 12 PROGRAM 13 PROGRAM 14 PROGRAM 15 PROGRAM 16 PROGRAM 17 PROGRAM 18 PROGRAM 19 PROGRAM 20 PROGRAM 21 PROGRAM 22 PROGRAM 23 PROGRAM 24 PROGRAM 25 GRADIENT EFFECT PROGRAM SPEED SLOW FAST PAN TILT MOVEMENT SPEED MAX TO MIN SPEED BLACKOUT BY MOV
30. e 40 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 41 Channel Channel dd 2 21 BE i mil i 11 RED 3 28 re BLUE 8 0 255 0 100 0 255 0 100 b l i B i Illusion Dotz 4 4 59 Channel DMX Mode Channel Value Function Illusion Dotz 4 4 59 Channel DMX Mode Channel Value Function 0 255 0 100 0 255 0 100 0 255 0 100 0 100 0 100 RED 14 0 100 GREEN 14 0 100 BLUE 14 0 100 RED 15 0 100 GREEN 15 0 100 BLUE 15 0 100 RED 16 0 100 GREEN 16 0 100 52 A BLUE 16 0 255 100 GE ae SHUTTER amp STROBE 0 31 LED S OFF ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 42 SHUTTER amp STROBE LED S ON STROBING SLOW FAST LED S ON PULSE EFFECT IN SEQUENCES LED S ON RANDOM STROBE SLOW FAST LED S ON DIMMER CURVES STANDARD STAGE TV ARCHITECTURAL THEATRE DEFAULT TO UNIT SETTING PROGRAM 1 PROGRAM 2 PROGRAM 3 PROGRAM 4 PROGRAM 8 PROGRAM 9 PROGRAM 10 PROGRAM 11 PROGRAM 12 PROGRAM 13 PROGRAM 14 PROGRAM 15 PROGRAM 16 PROGRAM 17 PROGRAM 18 PROGRAM 19 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 43 Illusion Dotz 4 4 59 Channel DMX Mode Function _____ Illusion Dotz 4 4 Photometric Chart Intensity LUX AUTO PROGRAMS Red LEDs 9160 4090 2020 1280 832 18
31. electronically using the controls on the front panel of the unit Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use stan dard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and 8 lighting stores Your cables should be made with a male and female XLR connector on either end of the GORE Also ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 9 Illusion Dotz 4 4 Set Up remember that DMX cable must be daisv chained and cannot be split Notice Be sure to follow figures two and three when making vour own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMXS12 OUT DMXS12 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 XLR Female Socket I 2 ey i Li J l l I I 1 1 Li XLR Male Socket e 1 1 H l 1 Ground 2 Cold 1 1 1 1 1 1 1 Figure 3 XLR Pin Configuration Pin 1 Ground Pin 2 Data Compliment negative Pin 3 Data True positive Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last u
32. ge 19 Illusion Dotz 4 4 System Menu Protocol Set KLING NET ARTNET With this function you can select the soft ware for which you are going to control the fixture 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Protocol Set is displayed press ENTER 3 Either Kling Net or ArtNet will be displayed Use the UP or DOWN buttons to find the software you wish to use and press ENTER to select 4 Press the MODE button to exit Net Switch NET SWITCH This function will activate the unit to receive Kling Net ArtNet signal 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Net Switch is displayed press ENTER 3 Either On or Off will be displayed To activate the Net Switch use the UP or DOWN buttons to select On and press ENTER to select 4 Press the MODE button to exit Fan Set HEAD FAN With this function you can adjust the speed of the moving head fans 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Head Fan is displayed press ENTER 3 Either Auto Fan Speed default Low Fan Spee
33. in master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a terminator at the last fixture 2 On your Master unit access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 3 Press the UP or DOWN buttons until Disp Set is displayed and press ENTER 4 Select your desired operating mode Use the UP or DOWN but tons to select between Auto Pro or Sound Ctrl press ENTER to select your desired program 5 Either Master or Alone will be displayed Using the UP or DOWN buttons select Master and press ENTER 6 For your Slave units access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 7 Press the UP or DOWN buttons until Disp Set is displayed and press ENTER 8 Press the UP or DOWN buttons until Slave Mode is displayed and press ENTER 9 Either Slave 1 Slave 2 or Slave 3 will be displayed Select your desired Slave setting and press ENTER 10 Press MODE if you want to return to the main menu ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 32 Illusion Dotz 4 4 Kling Net or Art Net Operation 1 Activate the Net Switch using the instructions on page 20 under Net Switch Select your software using the instructions on page 20 under
34. ion is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Total Time is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the total run ning time 5 Press ENTER or press MODE to exit LAST CLEAR This will allow you to check when the last running time was cleared 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Last Clear is displayed and press ENTER 4 KXXX will now be displayed XXXX represents the last running time 5 Press ENTER or press MODE to exit RUN PASSWORD This will display the timer password 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 26 Illusion Dotz 4 4 System Menu 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Timer Pin is displayed and press ENTER 4 The Timer Pin is 050 5 Press ENTER or press MODE to exit CLEAR LAST This will allow you to clea
35. k off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 46 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fallen or liquid has been spilled into the appliance B The appliance has been exposed to rain or water C The appliance does not appear to operate normally
36. l Error Info is displayed press ENTER 3 Use the UP or DOWN buttons to find the error message that needs to be cleared 4 Press ENTER or press MODE to exit MODEL INFO In this menu you are able to see the lamps model information 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Model Info is displayed press ENTER 3 XXXX will now be displayed XXXX represents the model infor mation 4 Press MODE to exit SOFTWARE VERSION This will allow you to see the software ver sion of each IC 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Software Version is dis played press ENTER 3 Use the UP or DOWN buttons to scroll through each IC and see the software version 4 Press MODE to exit ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 28 Illusion Dotz 4 4 System Menu TEST RESET MOTORS With this function you can reset the Pan amp Tilt motors 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Test is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Motor is displayed press ENTER 3 Press ENTER to reset or press MODE t
37. n is highlighted then press ENTER 2 Press the UP or DOWN buttons until Fixture ID is displayed press ENTER 3 Press UP or DOWN buttons until Device IP Addr is displayed and press ENTER 4 XXX XXX XXX XXX will be displayed XXX XXX XXX XXX repre sents the units current Device IP Address 5 Press ENTER or press MODE to exit CTRL IP ADDR With this function you set the Console IP address 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Fixture ID is displayed press ENTER 3 Press UP or DOWN buttons until Ctrl IP Addr is displayed and press ENTER 4 XXX XXX XXX XXX will be displayed XXX XXX XXX XXX repre sents the units current Device IP Address 5 Press ENTER or press MODE to exit UNIVERSE With this function you can enter the port number 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Fixture ID is displayed press ENTER 3 Press UP or DOWN buttons until Universe is displayed and press ENTER 4 XXX will be displayed XXX represents the units current Device IP Address 5 Press ENTER or press MODE to exit ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Pa
38. nit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems o and interference lt is alwavs advisable 5 fa to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX l and PIN 3 DMX of the last fixture Figure 4 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 10 Illusion Dotz 4 4 Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In ETE TE ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 11 Illusion Dotz 4 4 System Menu Receive Set Address A001 AXXX DMX
39. o exit TEST CHANNEL With this function you can test correct each chan nel function 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Test is highlighted then press ENTER 2 Press the UP or DOWN buttons until Test Channel is displayed press ENTER 3 Use the UP or DOWN buttons to scroll through the various chan nels 4 Press ENTER or press MODE to exit PANEL CTRL With this function you can easily adjust the lamp All effects will be canceled the shutter will open and output intensity will be 100 With the individual functions you can focus the light on flat surface a wall and finely adjust the lamp 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Test is highlighted then press ENTER 2 Press the UP or DOWN buttons until Panel Ctrl is displayed press ENTER 3 Use the UP or DOWN buttons to scroll through the various func tions Press ENTER when you find the function you would like to adjust 4 Press ENTER or press MODE to exit CALIBRATION With this function you can calibrate and adjust the effects wheels to their correct positions The Calibration password ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 29 Illusion Dotz 4 4 System Menu 050 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Effect Adjust is highlighted then press
40. ot display ing a R A number on the outside of the package will be returned to the shipper at the shippers cost ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 6 Illusion Dotz 4 4 Mounting When installing the unit the trussing or area of installation must be able to hold 10 times the weight without any deformation When installing the unit must be secured with a secondary safety attach ment e g and appropriate safety cable Never stand directly below the unit when mounting removing or servicing the unit Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself These installaiton should be checked by a skilled person once a year QQ The Illusion Dotz 4 4 is fully operational in two different mounting positions hanging upside down from a ceiling or set on a flat level surface To avoid internal damage to the unit never mount the unit on its side Be sure this fixture is kept at least 0 5m away from any flam mable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the cl
41. otate flip the display 180 degrees 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until LCD Set is displayed press ENTER ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 21 Illusion Dotz 4 4 System Menu 3 Press UP or DOWN buttons until Flip Display is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit KEY LOCK With this function activated the buttons will lock autom matically after 15 seconds 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until LCD Set is displayed press ENTER 3 Press UP or DOWN buttons until Key Lock is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit DISPFLASH With this function activated the the display will flash when there is not DMX signal 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until
42. r Master or Alone will be displayed Use the UP or DOWN buttons to change the operating mode 4 Press ENTER to to make your selection or press MODE button to exit DEFAULT RESET 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until DFSE is displayed press ENTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit INFORMATION Time Information Time information is always represented in hours CURRENT RUNNING TIME This will allow you to check the units current running time 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Current is displayed and press ENTER ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 25 Illusion Dotz 4 4 System Menu 4 XXXX will now be displayed XXXX represents the current run ning time 5 Press ENTER or press MODE to exit TOTAL RUNNING TIME This will allow you to check the units total running time 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Informat
43. r the last run time of the unit You need to put in the Timer PIN before doing this Please see the section before this 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Clear Last is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit TEMPERATURE INFO This will allow you to check the moving head temperature 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Temp Info is displayed press ENTER 3 Head Tem will now be displayed press ENTER 4 XXX will now be displayed XXX represents the current tem perature of the moving head 5 Press ENTER or press MODE to exit ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 27 Illusion Dotz 4 4 System Menu ERROR INFO In this menu you are able to reset the error message 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons unti
44. s bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 46 Illusion Dotz 4 4 Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LL
45. tant safety information regard ing the use and maintenance of this unit Please keep this manual with the unit for future reference Illusion Dotz 4 4 Handling Precautions Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC During operation the housing may become extremely hot Avoid touching the unit with bare hands while in use ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit Illusion Dotz 4 4 Product Registration The Illusion Dotz 4 4 carries a two year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by con tacting our customer support team on our toll free customer support number All packages returned to the service department n
46. uttons to scroll through the Edit modes Press ENTER to select any of the Edit modes Edit A B or C This function allows the user to make the actual changes in the user defined modes that are created in the previous function Function REMOTE ADD With this function you can adjust the DMX address via external controller 1 Press the MODE button to access the main menu Press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status is displayed press ENTER 3 Press UP or DOWN buttons until Remote Add is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE to exit To use this function follow these instructions To adjust the address of your unit you must first go to the address that it is currently set to From there you can adjust the address First make sure all channels are set to the value of 0 1 On your DMX controller set the DMX value of Channel 1 to the value 7 2 Now set the DMX value of Channel 2 to the value 7 to adjust the starting address between 1 and 255 To adjust the address between 256 and 511 set Channel 2 to the value 8 3 Set the DMX value of Channel 3 to your desired starting address This will take about 20 seconds before the unit accepts the new DMX address
47. year 365 day Limited Warranty and batteries which have a 180 day limited warranty ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 47 IIlusion Dotz 4 4 Notes Illusion Dotz 4 4 Notes ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 48 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 49 Illusion Dotz 4 4 Specifications Model Illusion Dotz 4 4 Voltage 100 240V 50 60Hz LEDs 16 x 30W RGB COB LEDs Beam Angle 15 Degrees Power Consumption 490W Power Cord Daisy Chain 3 Fixtures Max 120V 5 Fixtures Max 220V Dimensions 15 5 L x 19 5 W x 18 5 H 393mm x 492mm x 467mm Weight 36 Lbs 16 5 kgs Fuse 3A Duty Cycle None DMX 3 DMX Channel Modes 12 Channels 14 Channels or 59 Channels Sound Active Yes Working Position Any Safe Secure Position Warranty 2 Year 730 days Auto Sensing Voltage This fixture contains a electronic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 50 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A
48. you Table of Contents Aa eiza UG A 3 eg Zeta lie ie EE 3 Customer SUP POM ss ciseacsasscitecnachaadtes snes vesshaxeeacndeiudagvescscceactberaders 3 Safety ErGGOUIODS aaa 4 ENEE geet 5 Handling PRECAUTIONS E 6 E E E 6 NIR e 7 8 DMX Set iri dee EAR EES EES 9 11 RE 12 Operaatio E 31 32 Kling Net ArtNet Control 33 DMX Heed 34 44 Fuse Repla ement arrarena ear 46 FS UMA E 46 Trouble SIMO OUI BEE 46 WV RR eege Ae 47 opeciticatto tt EE 50 ADJ Products LLC www adj com Illusion Dotz 4 4 Instruction Manual Page 2 Illusion Dotz 4 4 General Information Unpacking Thank you for purchasing the Illusion Dotz 4 4 by ADJ Products LLC Every Illusion Dotz 4 4 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for fur ther instructions Please do not return this unit to your dealer without contacting customer support first Introduction The Illusion Dotz 4 4 is a DMX intelligent moving head fixture The Illusion Dotz 4 4 can be a 12 channel 14 channel or 59 Channel DMX unit The fixture can operate in three different operating modes show mode sound
Download Pdf Manuals
Related Search