GA80-B7061 Quick Installation Guide
Contents
1. the Chassis pre installed pre installed Align the tabs on Air Duct and install onto 1 the chassis Preparing the Chassis eran Read normal ESD Electrostatic Discharge procedures 7 40x40x56mm system FANs 1 M1618G80 D PDB 1 M1201 L16 1F riser card 1 M1202 L16 1F riser card Place your TYAN Server Chassis on a flat anti static surface to perform the following integration procedures Read ESD procedures before reaching inside to install components pre installed pre installed pre installed pre installed 1 M7018 BP SG HDD backplane 1 M2091 R PCI E riser card 1 M1706G62 FPB front panel board pre installed pre installed pre installed TYAN Quick Installation Guide Unscrew the riser bracket f Remove the screw on the Loosen the 2 thumb screws on 3 Slide to remove the top cover 2 CPU heatsinks 2 Sliding rails amp 1 screw pack 1 Quick Installation Guide 1 Driver s and Utilities CD nop covey the rear side 1 Alr duct 2 Mounting ear 2 Intel GPU 1 AC Power cord US 1 AC power cord EU 3 Screw pack amp 1 screw pack bracket Required Hardware Components Minimum Hardware Requirements Press the locking lever latch and 2 Slide the HDD tray out pull the locking lever open To avoid integration difficulties and possible board damage your system must meet the following minimum requirements e Proces2. GA80 B7061 Quick Installation Guide Document D2263 100 Revision 1 0 etl General Information System Installation Read Me First The User s Manual is available for download from our Web site at http www tyan com Make sure to read all precautions and instructions before you start installing the server system Installing the CPUO Heatsink Installing the Air Duct a A U YN _ A NO Refer all servicing to qualified personnel to avoid the risk of damage to the server system Ke SS SX lt SS SS SS ws Sy as ye K G w WS amp Exercise normal ESD Electrostatic Discharge procedures during system integration TYAN MiTAC recommends wearing Ss gloves and an anti static wrist strap to avoid possible damage to the equipment 4 Current processor socket design places the pins on the motherboard instead of the processor itself Exercise caution when installing the processors as the manufacturer s warranty does not cover damage inflicted upon the motherboard including damage to the CPU sockets Box Content E oF oS Glenn a 1E i Eeee ered T g f ANA it Hh ewe Y 9 el a Toha la ee EL p eo e 9 l EX zl g o S E mR 1E cm 4 Oe _ e I a eee ni Pd a 2 com 3m g e 2 e 1U chassis 4 hot swap HDD bays TYAN 7061 system board 1 1 200W 80 Platinum power supply Open
3. l C D Chassis intrusion header 2PHD_1 9 LC C CPU1 DIMM SLOT Channel A B JUMPER D CPU1 DIMM SLOT Channel C D a DOA RMA Reminder 10 1 PCIE Gen3 slot x16 POEG CPU XDP bypass jumper 3PHD_2 3PHD_3 nor a so r ME recovery mode jumper 3PHD_4 Note Please save and fale the CPU TEG oon Ce en gt Slot Xx BIOS recovery mode jumper 3PHD_5 protection cap when returning eo E ERE e223 4 PCIE Gen3 slot x8 COM port select jumper 3PHD_6 3PHD_7 the server board for the service edh a cb 5 PCIE Gen3 slot x16 Security override mode jumper 3PHD_8 11 12 13 14 15 16 1718 19 20 Note There is a risk when setting the jumper by yourself A T A SETERS Y l BMC reset jumper 3PHD_11 Connect the add on card to the connector Close the latch to secure the add on card to on the riser card the riser bracket AANA ONIN www tyan com
4. ling other GPU cards onto the riser bracket please refer to the User s 1 COM2 header J3 20 CPU fan power connector Loca te the external I O port Manual on our website at http www tyan com 2 USB2 0 ports and LAN port 3 LAN3 21 8 pin fan connector from down to up 3 BIOS J2014 J2013 J2012 J2009 J2008 Ethernet 36 35 34 33 32 31 30 29 28 27 26 25 4 ID_LED button 22 Fan connector SYS_FAN_2 LAN3 5 ID_LED 23 Fan connector SYS_FAN_1 shared with IPMI 6 VGA port 24 8 pin power connector PW6 Leo TA 7 Power button 25 4 pin power connector PW9 1 Ce SE 8 LAN port 1 LAN1 26 PDB to MB connector J2006 aF 9 LAN port 2 LAN2 27 Type A USB connector A_USB1 i 10 Port 80 header J2004 28 Front panel connector FPIO1 j o 11 CPUO fan power connector 29 SAS SMbus header J205 a4 12 Clear CMOS button 30 8 pin power connector PW4 USB 2 0 Ports ID LED button 13 Fan connector SYS_FAN_4 31 8 pin power connector PW5 3 14 8 pin fan connector J2011 32 24 pin power connector PW8 A j 15 8 pin power connector PW3 33 SATA2 i 16 8 pin power connector PW2 34 SATA1 5 17 8 pin fan connector J2010 35 4in1 Mini SAS connector z 18 USB front panel connector USB1 36 4in1 Mini SAS connector 6 19 Fan connector SYS_FAN_3 1 Pull the latch on the rear panel to release J SLOTS HEADER the PCI E bracket from the chassis g A CPUODIMMSLOT Channel A B Description B CPUO DIMM SLOT Channe
5. sor Intel Xeon processor E5 2600 Series with 5MB cache support e Memory Type Minimum of one 1GB 240 pin DDR3 800 1066 1333 1600 MT s DIMMs e Hard disk drives SATA SAS e Rack mount kit industry 19 rack mountable Unscrew the support bracket Insert the Nvidia GPU card Open the Open the Open the CPU Remove the cel and the PCI E brackets from onto the riser bracket and socket lever other socket lever socket cover protective cap the riser bracket secure it with 2 screws Tools prepared N y Install the processor Close the CPU Close the 8 Close the other Place a hard drive into Reinsert the HDD tray into Press the locking lever SS SX and make sure the socket cover socket lever socket lever the drive tray the chassis to secure the tray Phillips screwdriver Y Flat head screwdriver Y Anti static wrist strap golden arrow is located Use four screws to Repeat the same procedures in the right direction secure the HDD to install other HDD trays Secure the GPU card to the riser Align and install the riser 8 Secure the riser assembly to bracket with the 6 screws and assembly onto the chassis the chassis with the 3 screws connect the GPU cable 2 Motherboard Placement Note 1 The Intel GPU brackets will only be included in B7061G80W4H X SKU CONNECTORS Motherboard Placement 2 There are two riser brackets inside the chassis For instal
Download Pdf Manuals
Related Search