English Manual
Contents
1. BIND Ye CONNECTION PERFECTION SAS SATA II RAID System User Manual English LINDY No 20637 CE Fe WWW LINDY com Tested to Comply with FCC Standards O LINDY ELECTRONICS LIMITED amp LINDY ELEKTRONIK GMBH FIRST EDITION Apr 2010 English Manual Product Features Frame Aluminium material and Plastic material for the front bezel Interface Support SAS SATA I SATA II Form Factor 1 x 5 25 Bay for 4 x 2 SAS amp SATA Hard Drive SSD High performance transfer rate up to SAS 3Gb s amp SATA 3Gb s With built in Raid controller amp Support external RAID modes including RAID 0 1 3 5 10 JBOD Large Clone amp Normal Single Plug amp play hot swappable Supports 2 5 single hard drive up to 14 5mm thickness in height With 4 Pin Power connector and 7 Pin Signal connector Built in 2 x 4cm 4020 cooling fan Mechanical lock on the front of each HDD tray LED for Power amp HDD access functions Dimension 173 5 L X 146 W X 42 H mm Weight 0 79kg English Manual 3 HDD Installation 1 For 2 5 SATA HDD SSD put it into the tray as shown on Picture A 1 and use the provided screws to mount it on the HDD tray 2 For 2 5 SAS HDD or HDD with more than 10 5mm in height unscrew the cover mounting screw and remove the upper cover Then mount the SAS HDD or the thick HDD to the open tray Note After installation of a SAS HDD do not remount the upper cover since the SAS HDD hei2. EE for the collection and recycling of all waste electrical and electronic equipment The wheelie bin symbol shown indicates that this product must not be disposed of with household waste Instead the product must be recycled in a manner that is environmentally friendly For more information on how to dispose of this product please contact your local recycling centre or your household waste disposal service Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways Please follow your national law when you want to dispose of any electrical or electronic products More details can be obtained from your national WEEE recycling agency Germany Deutschland Die Europ ische Union hat mit der WEEE Direktive umfassende Regelungen f r die Verschrottung und das Recycling von Elektro und Elektronikprodukten geschaffen Diese wurden von der Bundesregierung im Elektro und Elektronikger tegesetz ElektroG in deutsches Recht umgesetzt Dieses Gesetz verbietet vom 24 M rz 2006 an das Entsorgen von Elektro und Elektronikger ten ber die Hausm lltonne Diese Ger te m ssen den lokalen Sammelsystemen bzw rtlichen Sammelstellen zugef hrt werden Dort werden sie kostenlos entgegen genommen Die Kosten f r den weiteren Recyclingprozess bernimmt die Gesamtheit der Ger tehersteller C C LINDY No 20637 FC 1 Edition April 2010 www lindy com
3. Four hard drives Clone environment data in each hard drive will be same CLONE Disk 0 Disk 1 Disk 2 Disk 3 Normal Single DIP Switch Setting SW1 OFF SW2 OFF SWS OFF Normal mode means all of the configured hard drives exist and the RAID System is not in the rebuild condition User can see the original hard drives from the host which supports port multiplier technology Note If the host does not support port multiplier function then you will find only one hard drive on the operating system The RAID tool is useful in this case Reserved DIP Switch Setting SW1 OFF SW2 OFF SW3 ON This mode is reserved for future functionality Radio Frequency Energy Certifications FCC Warning This equipment has been tested and found to comply with the limits for a Class B Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the fol
4. ght is higher and does not leave enough space for the cover Picture A 2 Store the upper in a safe place This HDD tray can fit the HDD max to 15mm high Safety Lock The mechanical lock design keeps the HDD inside the frame and prevents it from being taken out while the HDD is working See Picture B1 amp B2 a How to LOCK the HDD Tray olide in the HDD tray and press the front handle to lock the HDD tray on the frame See picture B 2 b How to OPEN the HDD Tray Use a finger to hold the Clicker Lock on the front panel and pull the HDD tray out see Picture B 1 Front Panel amp Real View See Picture C amp D 4 Picture C English Manual 4 C1 C4 HDD Tray C5 Mechanical locker for front panel C6 Blue LED blinking while HDD is accessing No LED indication if HDD is not being accessed Picture D Picture E D7 4 pin power connector D8 D9 Cooling FAN D10 RAID Mode configuration DIP switch see Picture E for details D11 Change Mode Button After setting the RAID mode from the DIP Switch the new Raid mode can be effective only after you pressed the hChange Mode Button h for more than 2 seconds D12 For SATA or SAS data port connections to the host SATA or SAS RAID controllers RAID Mode Setting amp Description RAID 0 Disk Striping DIP Switch Setting SW1 ON SW2 ON SW3 ON RAID 0 or Stripe is the segmentation of logically sequential data such as a single file so tha
5. lowing measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced technician for help You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CE Statement EMC Compatibilty This device complies with EN Standards EN55022 and EN55024 according to the relevant EC EMC Directive It must be used with shielded cables only to maintain EMC compatibility Dieses Produkt entspricht den einschl gigen EMV Richtlinien der EU und darf nur zusammen mit abgeschirmten Kabeln verwendet werden LINDY Herstellergarantie LINDY gew hrt f r dieses Produkt ber die gesetzliche Regelung hinaus eine zweijahrige Herstellergarantie ab Kaufdatum Die detaillierten Bedingungen dieser Garantie finden Sie auf der LINDY Website aufgelistet bei den AGBs WEEE Waste of Electrical and Electronic Equipment Recycling of Electronic Products In 2006 the European Union introduced regulations WE
6. s also named Concatenating In this mode the RAID System will concatenate all of the hard drives into a single hard drive with larger capacity For example if three 500GB hard disks are connected to the RAID System in concatenating mode user will get a single hard disk with capacity of 1 500 GB after it is configured JBOD Disk O Disk 1 Disk 2 RAID 3 Parity protection DIP Switch Setting SW1 ON SW2 OFF SW3 OFF RAID 5 Parity protection DIP Switch Setting SW1 OFF SW2 ON SW3 OFF XOR engine in the RAID System generates Parity Block In RAID 3 mode Parity Block will be stored in the same hard drive While in RAID 5 mode Parity Block will be spread over all of the different hard drives The RAID System will also make use of same size disk space in each hard disk under RAID 3 5 condition Note Failure in a hard disk will cause the RAID System enter degrade mode and in this case host controller still could read write data through the RAID system normally without knowing any defects Users have to replace the defective hard disk the RAID System then will enter into the identical rebuild mode automatically RAID 3 RAID 5 English Manual 7 Clone DIP Switch Setting SW1 OFF SW2 ON SW3 ON This mode is useful especially when users would like to copy data from a hard drive to several hard drives at the same time The action of Clone is similar to RAID 1 However all of the hard disks will be the mirrors For example in a
7. t segments can be assigned to multiple hard disks in a round robin fashion and through written concurrently Note If any hard disk becomes defective information stored in this RAID 0 mode will be invalid RAID 0 Disk 0 Disk 1 English Manual RAID 1 Mirroring for high security RAID 1 or Mirror is the replication of data onto separate HAI D 1 hard disks in real time to ensure continuous availability Take a RAID 1 system with two hard disks as an example data in a hard disk will be exactly the same as the data in another hard disk Note Failure in a hard disk Host controller still could read write data Users have to replace the defect hard Disk and the RAID system will enter identical rebuild mode automatically when you replace a new hard disk in RAID 1 0 For high performance amp high security DIP Switch Setting SW1 ON SW2 ON SWS OFF RAID System could be configured to support Stripe and Mirror at the same time i e RAID 10 Take four hard drives RAID 10 as an example hard drive 0 and hard l drive 1 could act as Mirror 1 and hard drive 2 and hard Disk 0 Disk 1 drive 3 could act as another Mirror 1 too The system then will configure these two Mirrors as Stripe RAID 10 RAID O Please note When DIP Switch is set to RAID 10 and you installed two HDD only the system uses the RAID 1 mode English Manual 6 JBOD Concatenating DIP Switch Setting SW1 ON SW2 OFF SW3 ON This mode i
Download Pdf Manuals
Related Search