Cen-Tec CT24QD Manual - Central Vacuum Supplier
Contents
1. Length z Adjust y Button Overload Protector Overload Protector The overload protector reset button protects the motor from brush jamming and belt breakage H the agitator slows down or stops the overload protector shuts off the brush To correct problem Unplug the electrical cord remove obstruction Check brush area for excessive lint buildup or jamming To reset Press the reset button on top of the brush Plug in the power cord turn on vacuum and brush DO NOT attach or remove handle or wands while cleaner is ON This could cause sparking and damage the electrical contacts To remove wand from the POWER HEAD lock wands in straight up position ei Wand 1 Press wand easy release Easy e Release Pedal with foot and pull Pedal the wands straight up out of the POWERHEAD The plug and cord do not have to be removed to use attachments on the wands2. unplug grasp plug not the cord Do not handle system or appliances with wet hands Turn off all controls before unplugging Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to distributor 10 1 12 13 14 15 16 Do not allow to be used as a toy Close attention is necessary when used by or near small children The hose contains electrical wires Do not use if damaged cut or punc tured Avoid picking up sharp objects Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of the body away from open ings and moving parts Do not leave vacuum or brush when plugged in Unplug from outlet when not in use and before servicing Do not pick up flammable or com bustible liquids such as gasoline or use it in areas where they may be present Use extra care when cleaning on stairs Save These Instructions INTENDED FOR HOUSEHOLD USE ONLY EXPLOSION PARTS amp LIST E See next page for CT 24QD Hard Floor Nozzle Brush parts explosion and list CT 24QD Electric Power Nozzle lllustration Part 55904 2 55915 3 40438A 4 55926 5 55937 6 55948 1 55959 8 55970 9 55981 10 55992 II 56003 H 56014 13 56025 14 56036 15 56047 16 5605
3. 8 H 56069 18 56080 19 56091 20 56102 21 56113 22 56124 23 56135 24 56146 Part Description Lower Plate Wheel Lifter Note current service part Indicator Block Unit Pedal Height Adjust Pedal Bottom Height Adjust Screw Axle Assembly Agitator Unit Belt Motor Overload Protector Contact Terminal Unit Screw Motor Spring Motor Gasket Lead Wire Lead Wire Spring Protector Handle Protector Lock Handle Release Pedal Handle Release Pedal Fitting Handle Release Spring Handle Release illustration 25 26 21 28 29 30 3l 32 33 34 35 Part 56157 56168 56179 56190 56201 56212 56223 56234 56245 56256 56267 Part Description Pedal Brush Release Agitator Cover Bulb Unit Belt Reset Wire Connector Nozzle Housing Furniture Guard Window Heigth Adjust Button Belt Reset Agitator Cover Floor Nozzle Brush Assembly Power Nozzle Assembly Note Floor Nozzle Brush and Power Nozzle are optional if Cen Tec needs to service as a one piece unit KM TO WARNING Electrical Shock or Personal Injury Hazard Disconnect electrical supply before servic ing or cleaning the unit Failure to do so could result in electrical shock or personal injury from cleaner suddenly starting To Check Agitator Assembly When brushes are worn to the level esche of the base support x GC bars replace the he agitator assembly Base Support Bars E AGITATOR SERVIC
4. E EXPLOSION PARTS amp LIST d Quiet drive GEN EC CT 24QD Hard Floor Nozzle Illustration Part Part Description Illustration Part Bart Description 56278 Nozzle Brush Unit II 56388 Pedal Spring 2 56289 Contact Base Unit H 56399 Foot Pedal Upper 3 56300 Suction Inlet 13 56410 Rear Cover 4 56311 Screw 14 56421 Front Cover 5 56322 Nozzle Support H 56432 Screw 6 56333 Connection Cord Swivel l6 56443 Swivel Cap Floor Nozzle 1 56344 Wire Cover Front H 56454 Supporter Swivel Cap 8 56355 Screw 18 56465 Floor Nozzle Upper 9 56366 Lever Quick Release 19 56476 Floor Nozzle Bumper 10 56377 Foot Pedal Lower CT 24QD ELECTRIC BRUSH 8 1807 Morrissey Drive Bloomington IL 61704 Phone 309 664 0328 Toll Free 800 833 2822 Email help centecsystems com Cen Tec Systems Inc 2008 F51062 10 08 2 3 4 5 6 7 8 E SAFETY INSTRUCTIONS Please read all instructions before using this Electric Powerhead P O WARNING Electric shock could occur if used out doors or on wet surfaces Unplug and disconnect power before servicing Always turn off this appliance before connecting or disconnecting either hose or motorized nozzle Do not pick up anything that is burn ing or smoking such as cigarettes matches or hot ashes Use only as described in this manual Use only manufacturers recomm ended attachments Do not unplug by pulling on cord To
5. ING To Replace Agitator Assembly Remove the POWERHEAD cover belt and agitator assembly See To Remove Belt in BELT CHANGING AND AGITATOR CLEANING 2 Reinstall belt new agitator assembly and POWERHEAD cover See To Replace Belt in BELT CHANGING AND AGITATOR CLEANING D e N ef VN A g S SS Ae Remove the POWERHEAD cover as shown in BELT CHANGING AND AGITATOR CLEANING section 2 Push in and turn wise then pull out to remove bulb counterclock 3 Push in and turn the bulb clockwise to replace Bulb must not be higher than 130 volts 5 Watts Bush in and turn 4 Reinstall the POWERHEAD cover as shown in BELT CHANGING AND AGITATOR CLEANING section PILE HEIGHT SETTINGS E Pile Height Indicator Suggested pile height settings For best deep down cleaning use the XLO setting However you may need to raise the height to make some jobs easier such as scatter rugs and some deep pile carpets and to prevent Handle Release Pedal Pile Height Pedal XLO most carpet heights LO short to medium pile the vacuum cleaner from shutting off As a general guide MED medium to long pile HI shag and long pile Always follow all safety precautions when cleaning and servicing the POWERHEAD TO WARNING Electrical Shock or Personal Injury Hazard Disconnect electrical supply before servic ing or cleani
6. ke sure you have turned off the power Supplied to the electric brush nozzle by using the on off switch found on the handle 1 Using your foot simply depress the tab located on the rear of the electric brush that reads Brush Release 2 While keeping the tab depressed lift the wand in an upwards motion 3 This will disengage the hard flor brush from the electric nozzle RE INSTALLING THE HARD FLOOR BRUSH Note Make sure the on off switch located in the handle is still in the OFF position I Insert the front edge of the hard floor brush into the electric brush nozzle 2 Using the wand gently press down on the tool you will hear it snap into place 3 You are now ready to use the electric brush nozzle Edge Cleaner Active brush edge cleaners are on both sides of the POWER HEAD electric brush Guide either side of the brush along base boards or next to furniture to help remove dirt trapped at carpet edges Telescoping Wand The wand length is adjustable and requires no assembly To adjust simply push down on the wand adjust button and slide the upper wand to the desired height The swivel located on the POWER HEAD allows you to turn the handle to the left side to reach farther under low furniture When raising the wand you may have to hold the POWERHEAD with your hand or foot Wand Swivel SPECIAL FEATURES E a d IR Keep d Hand e Above Wand This Tab
7. ng the unit Failure to do so could result in electrical shock or personal injury from cleaner suddenly starting Belt Changing and Agitator Cleaning Disconnect cleaner from electrical outlet Frequently check and remove hair string and lint buildup in brush area If buildup becomes excessive disconnect the brush from wand and follow steps below To Remove Belt 4 Turn the POWERHEAD upside down 2 Unscrew the brush cover screws 3 Turn the POWERHEAD right side up Press handle release pedal and lower the swivel To remove cover grasp the sides and pull out to release the outside of the cover 4 Lift rear latches up AAT and tilt cover for ward from back until front snaps free JF lee f N Mf ae 5 Lift agitator assembly out remove worn belt and clear any hair string or lint build up from brush area E ELECTRIC BRUSH CARE To Replace Belt Install new belt e WY Z over motor drive D k Sch then over brush Al Aen EN d sprocket gt LA Brush Drive Sprocket Agitator 2 Replace agitator assembly back into the POWERHEAD 3 Line up front of cover and base Rest cover on front edge of base as shown 5 Tilt cover to back Press cover firmly until side and rear tabs snap into place Turn the POWERHEAD upside down and replace the 2 cover screws REMOVAL OF THE HARD FLOOR BRUSH NOTE Ma
Download Pdf Manuals
Related Search