MPC-2000 Series Hardware Manual
Contents
1. 6 Re install the cover of the MPC 2000 series and fasten the screws to secure the cover in place NOTE To fasten the screws on the cover of the MPC 2000 series we recommend that you use a T10 Trox Star screwdriver with a torque of 4 5 kgf cm 3 18 4 Driver Installation and Configure This chapter describes how to install the VGA driver and the touch screen driver for touch screen models After installing the drivers you can use the software tools to adjust display resolution and touch screen features on the MPC 2000 series The following topics are covered in this chapter O Installing the VGA Driver Setting Display Resolution Installing the Touch Screen Driver Performing Screen Calibration n DU D MPC 2260 MxGenerall o Driver Installation gt Installing the MxGenerallo Driver MPC 2260 UART Driver Installation gt Installing the UART Driver a MPC 2000 Series Hardware Driver Installation and Configure Installing the VGA Driver The steps below describe how to install the MPC 2000 series VGA driver for Windows Embedded Standard 7 After you install the VGA driver you can configure the display resolution settings using the utility provided by Intel 1 On the software CD that came with your MPC 2000 series go to the CD drive Driver Win7 32 bit or 64 bit 2 VGA folder L la es GO gt Computer USBDISK D Win7 32 bit n H Search 32 bit ol Organize v A Open2. Connecting Data Transmission Cables This section describes how to connect the MPC 2000 series to serial devices and the network Connecting to the Network To connect the MPC 2000 series to a network connect an Ethernet cable to an Ethernet port on the bottom panel of the MPC 2000 series The LED on the Ethernet port on the MPC 2000 series turns on to indicate that an Ethernet connection has been established The following figures indicate the location of the Gigabit Ethernet ports MPC 2240 MPC 2260 Gigabit Ethernet Port x 2 MPC 2190 The 10 100 1000 Mbps Ethernet LAN port uses 8 pin RJ 45 connectors The following diagram shows the pinouts and the descriptions for these ports LAN 2 100 Mbps Ethernet mode Yellow 1000 EE Gigabit Ethernet mode 3 12 MPC 2000 Series Hardware Hardware Installation and Connection Connecting Serial Devices You can configure the serial ports 1 and 2 male DB9 RS 232 RS 422 or RS 485 communications See the figure below for the location of the serial ports MPC 2240 MPC 2260 Serial Port x 2 RS 232 422 485 MPC 2190 Serial Port x 2 RS 232 422 485 DCD TXDA TXDA RxD rz C RS 232 RS 422 RS 485 4 wire RS 485 2 wire Do 2 RxD i GND Dep E LA RARA RR gt RA Configuring the Serial Ports For instructions on how to set the serial port for RS 232 422 485 communications refer to the examples in one of the following
3. Destination Folder C Program Files eG alaxT ouch Browse lt Back Next gt Cancel 10 Click Next to continue eGalaxTouch Select Program Folder Please select a program folder Setup will add program icons to the Program Folder listed below rou may type a new folder name or select one from the existing folders list Click Mest to continue Program Folder eGalaxT ouch Existing Folders Administrative Tools Games Maintenance Startup Subsystem for UN based Applications Tablet PC 11 If you want select Create a eGalaxTouch Utility shortcut on desktop Click Next to continue eGalaxTouch Setup Type Select the setup wpe that best suits your needs Select the features pon want to install and deselect the features you do not want to install Click Next to continue z Create a eGalaxTouch Utility shortcut on desktop 4 10 MPC 2000 Series Hardware Driver Installation and Configure 12 Wait until the installation is complete Setup Status eG alaxT ouch le configuring your new software installation InstallShield Cancel 13 Click Yes to perform 4 points calibration Ch The eGalaxTouch driver has been installed before operating touch WS function please do 4 point calibration Would you do 4 point calibration now MS A 14 The system displays a circle at each corner of the screen Touch the center of the circle until the screen displays OK Repeat this ste
4. Gigabit Ethernet LAN ports USB 2 0 ports dual AC DC power inputs and tape bonding Package Checklist The MPC 2000 series package is shipped with the following items 1 MPC 2000 series panel computer 2 keys for the removable storage trays 1 terminal block for DC power input 4 5 pin Euroblock terminals for NMEA 0183 v2 interfaces Documentation and driver DVD Quick installation guide printed Warranty card Optional accessories are also available upon request Desktop mounting kit Wall mounting clamps VESA mounting kit 1 2 MPC 2000 Series Hardware Introduction NOTE Please notify your sales representative if any of the above items are missing or damaged Product Features e 19 inch 24 inch or 26 inch display screen e Color calibration for ECDIS compliance e Fanless design e SavvyTouch display controls e 3rd Generation Intel Core Default Celeron 1047UE 1 40 GHz with Intel HD Graphics e Built in NMEA 0183 and software selectable RS 232 422 485 interfaces e Dual AC DC power supply units Hardware Specifications MPC 2260 Models Computer CPU Intel Celeron Processor 1047UE 2M Cache 1 40GHz OS Windows 7 Professional Windows XP Embedded Windows Embedded Standard 7 Windows XP SP3 System Chipset ntel HM65 System Memory 8 GB capacity 4 GB pre installed 1 slot of 4 GB DDR3 1600 204 pin SO DIMM SDRAM USB 4 bootable USB 2 0 hosts type A connectors Storage 2 SATA III interfaces 6
5. ground it Proper grounding and wire routing help 6 AC 100 240V limit the effects of noise due to electromagnetic interference EMI Run the ground connection from the ground screw to the grounding surface prior to connecting the power ATTENTION This unit is intended to be mounted to a well grounded mounting surface such as a metal panel 3 9 MPC 2000 Series Hardware Hardware Installation and Connection Powering On the MPC 2000 Series 1 Connect the MPC 2000 series display to a power source do one of the following e Connect the terminal block to the MPC 2000 Series DC Euroblock terminal located on the bottom panel e Connect the MPC 2000 series to a power source using the AC power cord provided 2 Touch the MENU button on the lower right hand corner of the display panel for about one second to turn on the MPC 2000 series NOTE It takes between 10 30 seconds for the system to complete the start up process Powering Off the MPC 2000 Series To power off the MPC 2000 series panel computer touch the MENU button for about four seconds Depending on the power management settings you configure in the operating system the MPC 2000 series may enter the standby hibernation or system shutdown mode To force the MPC 2000 series to shut down touch the MENU button for about 10 seconds NOTE If the MPC 2000 series is powered using a DC converter the INFO dialog displays the Error status for AC input power as sho
6. Hardware Introduction Serial Communication Parameters Data Bits 5 6 7 8 Stop Bits 1 1 5 2 Parity None Even Odd Space Mark Flow Control RTS CTS XON XOFF ADDC automatic data direction control for RS 485 Baudrate 50 bps to 115 2 Kbps supports non standard baudrates see user s manual for details Serial Signals RS 232 TxD RxD DTR DSR RTS CTS DCD GND RS 422 TxD TxD RxD RxD GND RS 485 4w TxD TxD RxD RxD GND RS 485 2w Data Data GND NMEA Interface Serial Standards 4 NMEA 0183 ports Base Serial Standard RS 422 Optical Isolation Protection 6kV contact discharge 8kV air discharge Voltage Differential 15 V to 15 V Baudrate 4800 bps Data Bits 8 Stop Bits 1 1 5 2 Parity None Handshake None LEDs System Storage Power LAN 100M Link x 2 1000M Link x 2 on connector Front Panel LEDs MENU Brightness INFO ECDIS Day Dusk Night Storage Smart OSD Yes Physical Characteristics Housing Aluminum sheet metal Weight 7 8 kg Dimensions 429 x 387 x 74 5 mm 16 89 x 15 24 x 2 93 in Mounting Flush mounting System Cooling Fanless thermal design Environmental Limits Operating Temperature 15 to 55 C 5 to 131 F Storage Temperature 20 to 60 C 4 to 140 F Ambient Relative Humidity 5 to 9 non condensing IP Rating e Front IP 54 e Rear IP 22 Anti Vibration e 0 7 g DNV 2 4 Class A sine wave 2 100 Hz 1 Oct min 1 5 hr per axi
7. folders on the software CD e For Windows 32 bit platforms lt Software DVD gt MPC 2000 Series Example X86 Release e For Windows 64 bit platforms lt Software DVD gt MPC 2000 Series Example x64 Release 3 13 MPC 2000 Series Hardware Hardware Installation and Connection Connecting NMEA 0183 Devices The MPC 2000 series comes with either eight NMEA 0183 ports MPC 2240 and MPC 2260 models or eight NMEA 0183 ports MPC 2190 models on the bottom panel The following figures show the location of the NMEA ports and the pin assignments MPC 2240 MPC 2260 TX RX NMEA 0183 Port x 8 MPC 2190 NMEA 0183 Port x 4 Connecting Speakers or Headphones The MPC 2000 series comes with standard 3 5 mm monaural line in and line out ports for connecting microphone speakers and headphones See the following figure for detailed location MPC 2240 MPC 2260 Line in Line out MPC 2190 Line in Line out 3 14 MPC 2000 Series Hardware Hardware Installation and Connection Connecting a PS 2 Keyboard and Mouse Your MCP 2240 MP computer comes with two PS 2 connectors to connect to a PS 2 keyboard upper connector and PS 2 mouse lower connector See the following figure for the detailed location MPC 2240 MPC 2260 PS 2 Keyboard PS 2 Mouse MPC 2190 PS 2 Keyboard Connector PS 2 Mouse Connector Connecting to USB Devices The MPC 2000 series comes with four USB 2 0 ports on t
8. 26 2011 12 22PM HDR File 13 KB E data2 5 26 2011 12 22 PM Cabinet File 1 KB ISSetup dll 5 26 2011 12 22 PM Application extens 540 KB _ layout bin 5 26 2011 12 22 DM BIN File 2 KB PS2setup 6 4 2007 10 13 AM Windows Batch File 1 KB _ PS2setup iss 4 25 2007 2 25PM ISS File 2 KB mE setup 5 24 200612 10PM Application 445 KB setup 7 15 2009 4 14 PM Configuration sett 1 KB _ setup inx 5 24 2011 4 44 PM INX File 272 KB _ setup isn 4 9 2007 4 17 PM ISN File 284 KB _ setup iss 12 24 2009 7 15PM __ ISS File 2 KB setup 12 2 2008 7 36 PM Text Document 1 KB _ TouchKit xpo 10 6 2008 3 13 PM XPO File 272 KB En setup Date modified 5 24 2006 12 10 PM Date created 2 7 2014 2 53 PM Application Size 444 KB MPC 2000 Series Hardware Driver Installation and Configure 3 Click Next to continue Welcome to the InstallShield Wizard for eGalaxT ouch The InstallShield Wizard will install eG alaxT ouch on your computer To continue click Mest eGalaxTouch Setup Type Select the setup wpe that best suits your needs Extra PS 2 interface driver for eG alaxT ouch controller Please check the check box for PS 2 touch controller Install PS 42 interface driver InstallShield 5 Select Install RS232 interface drive and click Next eGalaxTouch Setup Type Select the setup type that best suits your needs Extra AS 232 interface driver for eGalasT ouch controller Please check the check box for AS 232 touch con
9. 8 73 0 34 MPC 2240 9 24 0 36 576 83 22 71 512395 6 7 144 o 9 5 0 37 4 o 595 31 23 44 si e a W a l GC E d Se T Se a 3 D ii e Ha a S A 8 MPC 2000 Series Hardware Hardware Overview MPC 2190 10 550 42 407 93 16 06 74 5 2 93 36 2 1 43 mM d oi S 295 0 37 5 o S m Lo eN q x n o E wD cu wD cr 0000 SavvyTouch Display Control Buttons The MPC 2000 series comes with SavvyTouch display controls situated in the lower right corner of the screen These intelligent buttons will light up automatically when your fingers draw near Refer to the following table for more information on each button gg red system hardware error has occurred Brightness l White Displays the brightness mode Display mode ECDIS models only Brightness of display panel is out of ECDIS standard range Storage drive is functioning properly Storage Red eist Accessing or writing data to storage drive Off Storage drive is offline 2 4 MPC 2000 Series Hardware Hardware Overview Real Time Clock The real time clock in the MPC 2000 series is powered by a lithium battery Do NOT replace the lithium battery on your own If the battery needs to be changed please contact the Moxa RMA service team ATTENTION A There is a risk of explosion if the wrong type of battery is used To avoid this potential danger always use the cor
10. Contrast Ratio 5000 1 Light Intensity 300 cd m Viewing Angles 178 178 Active Display Area 531 36 H x 298 89 V mm Max Colors 16 7M 8 bit color Resolution e VGA 640 x 480 e SVGA 800 x 600 e XGA 1024 x 768 e SXGA 1280 x 1024 e WSXGA 1920 x 1080 benchmarked setting 1 5 MPC 2000 Series Hardware Introduction Ethernet I nterface LAN 2 auto sensing 10 100 1000 Mbps ports RJ 45 Magnetic Isolation Protection 1 5 kV built in Serial Interface Serial Standards 2 RS 232 422 485 ports software selectable DB9 male Serial Communication Parameters Data Bits 5 6 7 8 Stop Bits 1 1 5 2 Parity None Even Odd Space Mark Flow Control RTS CTS XON XOFF ADDC automatic data direction control for RS 485 Baudrate 50 bps to 921 6 Kbps supports non standard baudrates see user s manual for details Serial Signals RS 232 TxD RxD DTR DSR RTS CTS DCD GND RS 422 TxD TxD RxD RxD GND RS 485 4w TxD TxD RxD RxD GND RS 485 2w Data Data GND NMEA Interface Serial Standards 8 NMEA 0183 ports Base Serial Standard RS 422 Optical Isolation Protection 6 kV contact discharge 8 kV air discharge Voltage Differential 15 V to 15 V Baudrate 4800 bps Data Bits 8 Stop Bits 1 1 5 2 Parity None Handshake None LEDs System Storage Power LAN 100M Link x 2 1000M Link x 2 on connector Front Panel LEDs Storage SavvyTouch Display Control Buttons ECDI
11. D RS 485 4w TxD TxD RxD RxD GND RS 485 2w Data Data GND NMEA Interface Serial Standards 8 NMEA 0183 ports Base Serial Standard RS 422 Optical Isolation Protection 6 kV contact discharge 8 kV air discharge Voltage Differential 15 Vto 15 V Baudrate 4800 bps Data Bits 8 Stop Bits 1 1 5 2 Parity None Handshake None LEDs System Storage Power LAN 100M Link x 2 1000M Link x 2 on connector Front Panel LEDs Storage SavvyTouch Display Control Buttons ECDIS INFO Brightness MENU Physical Characteristics Housing Aluminum sheet metal Weight 16 6 kg Dimensions 621 x 444 x 90 mm 24 45 x 17 48 x 3 57 in Mounting VESA panel and desktop mounting Environmental Limits Operating Temperature 15 to 55 C 5 to 131 F Storage Temperature 20 to 60 C 4 to 140 F Ambient Relative Humidity 5 to 9 non condensing Note If you expect the storage temperature to exceed 40 C please ensure that the ambient relative humidity remains below 60 IP Rating e Front 1P54 e Rear IP22 Anti Vibration e 0 7 g DNV2 4 Class A sine wave 2 100 Hz 1 Oct min 1 5 hr per axis e 1g DNV2 4 random wave 3 100 Hz 2 5 hr per axis e 2 1 g DNV2 4 Class C sine wave 2 50 Hz 1 Oct min 1 5 hr per axis 1 4 MPC 2000 Series Hardware Introduction Power Requirements Input Voltage e 24 VDC 18 to 36 VDC screw type terminal block e 100 to 240 VAC AC power inlet Po
12. Gbps 2 5 removable storage trays BIOS 64 Mbit Flash BIOS with SPI ACPI Graphics Controller Intel HM65 Express chipset built in Video Outputs DVI D x 1 VGA x 1 female Other Peripherals Audio line in out 3 5 mm mini jack KB MS 2 PS 2 interfaces supporting standard PS 2 keyboard and mouse Display Panel Size 26 viewable image size Panel Type MVA Aspect Ratio 16 10 Pixels 1920 x 1200 WUXGA Pixel Pitch RGB 0 2865 H x 0 2865 V mm Response Time 15 ms gray to gray Contrast Ratio 1500 1 Light Intensity 300 cd m Viewing Angles 176 176 Active Display Area 550 08 H x 343 8 V mm Max Colors 16 7M 8 bit color Resolution e VGA 640 x 480 e SVGA 800 x 600 e XGA 1024 x 768 e SXGA 1280 x 1024 e WSXGA 1920 x 1080 e WUXGA 1920 x 1200 1 3 MPC 2000 Series Hardware Introduction Ethernet I nterface LAN 2 auto sensing 10 100 1000 Mbps ports RJ 45 Magnetic Isolation Protection 1 5 kV built in Serial Interface Serial Standards 2 RS 232 422 485 ports software selectable DB9 male Serial Communication Parameters Data Bits 5 6 7 8 Stop Bits 1 1 5 2 Parity None Even Odd Space Mark Flow Control RTS CTS XON XOFF ADDC automatic data direction control for RS 485 Baudrate 50 bps to 115 2 Kbps supports non standard baudrates see user s manual for details Serial Signals RS 232 TxD RxD DTR DSR RTS CTS DCD GND RS 422 TxD TxD RxD RxD GN
13. MPC 2000 Series Hardware Manual First Edition July 2015 www moxa com product MOXA 2015 Moxa Inc All rights reserved MPC 2000 Series Hardware Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice Trademarks O 2015 Moxa Inc All rights reserved The MOXA logo is a registered trademark of Moxa Inc All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa Moxa provides this document as is without warranty of any kind either expressed or implied including but not limited to its particular purpose Moxa reserves the right to make improvements and or changes to this manual or to the products and or the programs described in this manual at any time Information provided in this manual is intended to be accurate and reliable However Moxa assumes no responsibility for its use or for any infringements on the rights of third parties that may result from its use This product might include unintentional technical or typographical errors Changes are periodically made to the information herein to correct such errors and these changes are incorporated into new editions of the publication Technical Support Contact I nformatio
14. Next WARNING This program is protected by copyright law and 4 13 MPC 2000 Series Hardware Driver Installation and Configure 3 Click Install A Bet e Ge Bett TW ism a fi E T ee _ E A TP AA wit gl ai i e d e ira P eT oi i Le Bet ant ai ett Fa ga d em el AA SE bm DK aii nie ae oR St y EE ai Ra Ee tegt Zo V x E al a eT a ate L Je a aoe ar Lie s anpi AA GAS Ca A E Ready to Install the Program The wizard is ready to begin installation If you want to review or change any of your installation settings dick Back Click Cancel to exit the wizard C Program Files Moxa MxGenerallo User Information Company 4 Click Finish Ra Nicer assem ee eer SEELEN ZA MxGenerallo_W7_64 Click Finish to exit the wizard 4 14 MPC 2000 Series Hardware Driver Installation and Configure 5 Check your computer s Device Manager to verify that MxGenerall o Portl O Driver KMDF was installed correctly La Disk demes Be Display adapter 03 Human imedace Devices G DE AT ASA TAPT controller D Mice and ether port dee SP MOLA Embedded Drivers Network adapters TA Ports COM amp LPT DI Processors DN Farndrk O Securty Devices pi ym deent ei A Urerercal Senal Bus controller MPC 2260 UART Driver Installation Installing the UART Driver 1 Run the executable file MSSetup_QUADPORT exe located in the MCS7840_7820_Win7_64bit_driver_v1 4 7 19 WHQL
15. S INFO Brightness Power Physical Characteristics Housing Aluminum sheet metal Weight 12 4 kg Dimensions 595 x 393 x 75 mm 23 44 x 15 48 x 2 95 in Mounting Flush mounting Environmental Limits Operating Temperature 15 to 55 C 5 to 131 F Storage Temperature 20 to 60 C 4 to 140 F Ambient Relative Humidity 5 to 9 non condensing IP Rating P22 IP65 models available on request Anti Vibration e 0 7 g DNV 2 4 Class A sine wave 2 100 Hz 1 Oct min 1 5 hr per axis e 1 g DNV 2 4 random wave 3 100 Hz 2 5 hr per axis e 2 1 g DNV 2 4 Class C sine wave 2 50 Hz 1 Oct min 1 5 hr per axis Power Requirements Input Voltage e 24 VDC 18 to 36 VDC screw type terminal block e 100 to 240 VAC AC power inlet Power Consumption 40 to 75 W 1 6 MPC 2000 Series Hardware Introduction Standards and Certifications Safety UL 60950 1 CCC EMC EN 55022 Class B EN 55024 4 2 EN 55024 4 3 EN 55024 4 4 FCC Part 15 Subpart B Class A Marine IEC 60945 4th IEC 61174 IEC 61162 DNV2 4 ACS E10 Green Product RoHS cRoHS WEEE Reliability Automatic Reboot Trigger Built in watchdog timer WDT configurable for resets following 1 255 second hang intervals software programmable Warranty Warranty Period 1 year Details See www moxa com warranty MPC 2190 Models Computer CPU Intel Celeron Processor 1047UE 2M Cache 1 4 GHz OS Windows 7 Professional Windows XP Embedded W
16. Share with Y New folder j v Ai Oe eee Name Date modified Type Size de 1 Chipset 2 6 2014 3 33 PM Filefolder A Libraries d 2 VGA 2 6 2014 3 33 PM File folder de 3 Audio 2 6 2014 3 33PM File folder P Computer Le 4 Network 2 6 2014 3 33PM _ File folder amp Local Disk C Je S UART 2 6 2014 3 33PM _ File folder e USB DISK D dy 6 MxGenerallo 2 6 2014 3 33 PM File folder dy 7 Touch 2 6 2014 3 33 PM File folder th Network 2 VGA Date modified 2 6 2014 3 33 PM d File folder 2 Double click Win32_15319 e AAA A A a A A AAA A NA EY el ye de Computer LEA DEE Mh Win e 1 b ANGA di earch A D V Organce mi Open Mew folder HN G r T Eis Tr Faventes y vee Installation Fearne wal Libraries _ Relsaseblotes GFX 3165 pai 25 2015 11 FH KE IBA Win32 15319 NARIZ PM Application 117 922 KB JB Computer amp Local Disk i a USE DISK D th Neteark Site 115 MBE f 3 Wina 15319 Date modiied 7303 1 72 PM Date creabed 2 7 3014 355 PM bat cati n 4 2 MPC 2000 Series Hardware Driver Installation and Configure 3 The installation wizard screen appears Click Next to continue Gal Intel R Graphics Driver Software InstallShield Wizard ES Production Version Release Microsoft Windows 7 Microsoft Windows 8 Driver Revision 15 31 9 3165 May 10 2013 NOTE This document refers to systems containing the following Intel R processors 4th Generation Int
17. TC VGA Gigabit Intel HM65 LAN x 2 Line in out USB 2 0 x 4 SATA x 2 Keyboard Mouse Serial x 2 1 9 2 Hardware Overview The MPC 2000 series is compact well designed and hardened for industrial marine applications The intelligent SavvyTouch display control buttons allow you to easily locate and manipulate control buttons in low light environments or to receive immediate system hardware reports for troubleshooting The MPC 2000 series features a reliable and stable hardware platform with multiple serial ports for connecting a wide variety of data devices The following topics are covered in this chapter O Appearance gt Front View gt Bottom View O Dimensions gt MPC 2260 gt MPC 2240 gt MPC 2190 O SavvyTouch Display Control Buttons O Real Time Clock MPC 2000 Series Hardware Hardware Overview Appearance Front View Panel Buzzer Savvy Touch Display Control Buttons x 5 Bottom View MPC 2240 MPC 2260 RS 232 422 485 Port x 2 Line in out NMEA 0183 Port x 8 IIA KA AAA E aaa E 14 dest Ac Power Input Grounding Connector USB 2 0 Gigabit LAN Port x 2 Host x 4 2 0 SSD Trayx2 PS 2 Mouse Keyboard MPC 2190 RS 232 422 485 NMEA 0183 Port x 4 Potx2 GigabitLANx2 AC Power Input Line in out USB 2 0x 4 DVI D VGA Keyboard Mouse Output Connectors DC Power Input 2 2 MPC 2000 Series Hardware Hardware Overview Dimensions MPC 2260
18. VESA mounting bracket 3 6 MPC 2000 Series Hardware Hardware Installation and Connection MPC 2240 Round screw M4x4mm SUS Y Torque 5 kgf cm Flat screw M4x4mm SUS VESA mounting bracket MPC 2000 Series Hardware Hardware Installation and Connection MPC 2190 Round screw M4x4mm SUS Pd Torque 5 kgf cm Flat screw M4x4mm SUS Torque 5 5 kgf cm i VESA mounting P bracket 280 11 02 51 66 2 03 150 5 91 VESA Mounting Kit 4xM6 max 10 mm deep mounting holes 3 8 MPC 2000 Series Hardware Hardware Installation and Connection Wiring Requirements NOTE This section describes how to connect serial devices to the MPC 2000 series Read and follow these safety precautions before proceeding with the installation of any electronic devices e Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point Do NOT run signal or communications wires together with power wires in the same conduit To avoid interference wires with different signal characteristics should be routed separately e Based on the type of signal transmitted through a wire determine which wires should be kept separate and which bundled together The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together e Keep input wiring and output wiring separate e It is advi
19. ave Change Without Exit gt Exit Discarding Changes gt Load Optimal Defaults gt Load Custom Defaults gt Save Custom Defaults gt Discard Changes O Upgrading the BIOS MPC 2000 Series Hardware BIOS Setup Starting the BIOS Setup Utility NOTE To start the BIOS setup utility press the F2 key while the system is booting up The main BIOS Setup screen appears Select SCU to access the BIOS Configuration screen Continue Boot Manager Boot From File em AN A SCU The BIOS does not support the touch screen function You must connect a keyboard to the MPC 2000 series to configure the BIOS A short description of each function key is displayed at the bottom of the screen F1 General Help F5 F6 Change Values F9 Setup Defaults F10 Save and Exit Select Item lt gt Select Menu ESC Exit ENTER Select or go to Submenu 5 2 MPC 2000 Series Hardware BIOS Setup System Time F5 F6 Enter Main Information The main page displays the system hardware information such as the model name BIOS version and CPU type Advanced Settings Select the Advanced tab to display the Advanced screen as shown in the following figure Boot Configuration F5 F6 Enter MPC 2000 Series Hardware BIOS Setup Boot Configuration You can configure the numlock values in the Boot Configuration screen Option On default Off F5 F6 Enter Peripheral Configuration Use this screen to co
20. ce 1 Get the BIOS upgrade installation file The file name should have following format 2000xxSx exe xx refers to version numbers 2 Copy the file to the bootable USB drive Step 3 Run the upgrade program on the MPC 2000 Series 1 Reboot the computer press F2 while during the boot process to access the Boot Manager 2 Select Generic USB Flask Disk as the first boot source Press Enter to continue Boot Manager Boot Option Menu MOXA SSD Generic USB Flash Fisk t and to change option ENTER to select an option ESC to exit 3 When the boot process is complete a command screen appears Go to the directory where the upgrade file is located For example if the upgrade file is stored in the MPC2240 folder type cd MPC2240 C cd MPC2240 4 Run the upgrade program by typing 22410S02 exe Note that the upgrade filename may vary depending on the versions C MPC2240 gt 22410S02 exe 5 The system automatically executes the upgrade program Wait until the upgrade process is complete C gt 22410S02 exe Reading file flash package mode Option BIOS C Desc ME Please do not remove the AC power Insyde Flash Utility for InsydeH20 Version 1 5t Initializing Current BIOS Model name MPC 2240 New BIOS Model name MPC 2240 Current BIOS version V1 00S02 New BIOS version V1 00S02 Updating Block at FFDE8000 5 15 MPC 2000 Series Hardware BIOS Setup 6 After the upgrade process is comp
21. ch online this time only Windows will search for the latest drivers and applications for this device and download them to your computer Don t search online Your device may not function properly until you get the latest software Please read Microsoft s privacy statement Cancel 4 17 MPC 2000 Series Hardware Driver Installation and Configure 7 Click Close Update Driver Software High Speed USB MultiSerial Compound Device A ZEN rI It 4 18 8 BIOS Setup This chapter describes the BIOS settings of the MPC 2000 series marine panel computer The BIOS is used to initialize basic peripherals and helps boot the operating system before the operating system is loaded You can access the BIOS setup screens to change the configurations of these basic input output peripherals The configuration information is stored in the battery backed up CMOS RAM which retains the system information after the system reboots or when the power is disconnected The following topics are covered in this chapter O Entering the BIOS Setup Utility O Main Information O Advanced Settings Boot Configuration Peripheral Configuration HDC Configuration Video Configuration Chipset Configuration Y Y Y Y Y Y Hardware Monitor O Security Settings gt Set Supervisor Password O Power Settings O Boot Settings gt Boot Type gt EFI Device First gt Boot Delay Time gt Legacy O Exit Settings gt Exit Saving Changes gt S
22. dware Driver Installation and Configure 6 Click Next to continue tel Intel HD Graphics Driver Readme Fille Information UL i Refer to the Readme file below to view the system requirements and installation information Production Version Release Microsoft Windows 7 Microsoft Windows 8 Driver Revision 15 51 9 5165 May 10 2013 Intel Installation Framework Intel HD Graphics Driver Setup Progress Please wait while the following setup operations are performed Version 9 18 10 3165 Next gt Intel Installation Framework Intel HD Graphics Driver Setup Progress Please wait while the following setup operations are performed Copying File c Program Files Intel Intel R Processor Graphics uninstall th TH license txt eg Copying File c Program Files IntelIntel R Processor Graphics uninstall th TH setup exe mui Copying File c Program Files IntellIntel R Processor Graphics uninstall tr TR Yicense txt Copying File c Program Files Intel Intel R Processor Graphics uninstall ir TR setup exe mui Copying File c Program Files Intel Intel R Processor Graphics uninstall zh CN license txt Copying File c Program Files Intel Intel R Processor Graphics uninstall zh CN setup exe mu Copying File c Program Files Intel Intel R Processor Graphics uninstall zh TW license txt Copying File c Program Files Intel Intel R Processor Graphics uninstall zh TW setup exe mu Copying File C W
23. e computer mow Yes I want to restart this computer now 5 No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework 10 The MPC 2000 series will automatically restart Setting Display Resolution Follow these steps to adjust the display resolution 1 Right click the Intel HD Graphics Control Panel icon on the taskbar and select Graphics Properties Graphics Properties Graphics Options Exit Tray Intel R HD Graphics ontrol Panel intel 4 5 MPC 2000 Series Hardware Driver Installation and Configure 2 Select Display Intel HD Graphics Control Panel inteD Customize your graphics settings for an enhanced visual experience 3 You can make changes to the screen resolution refresh rate and image rotation Make sure that you select Maintain Display Scaling to maximize the display to fit the screen Click Apply to save the changes Intel HD Graphics Control Pane Display Ki splav Settir ge Caplay Settings Select Display T Bice E Advarced Digital Display EXPC 141 e Resolution Ch Prima WA Display Profiles LOA w uneni Settings k Relraih Rate ep Hz w Rotation Wo 3 180 270 Scaling W Maintain Display Seeing ES Cusiomine Ate Ratio 4 6 MPC 2000 Series Hardware Driver Installation and Configure 4 Click Customize Aspect Ratio to set
24. el R Core TM Processors with Intel R Iris R Pro Graphics 5200 4th Generation Intel R Core TM E Intel HD Graphics Driver Welcome to the Setup Program This setup program will install the following components Intel HD Graphics Driver It is strongly recommended that you exit all programs before continuing Click Next to continue Automatically run WinSAT and enable the Windows Aero desktop theme if supported Intel HD Graphics Driver License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note If you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHY or Independent Software Vendor TV this complete LICENSE AGREEMENT applies If you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT Intel Installation Framework 4 3 MPC 2000 Series Har
25. en ee ENEN ee eee tee TT ere Ter A A Ud Terre arr Tee 5 11 ENDS TI IS A A AAA RA RAR RA T 5 12 610 Gm Ee EM Din 5 12 Reie iii 5 12 E A A O O O 5 13 o desta 0 qlo El pr glo PO E E EE TEOT OA 5 13 Save Change Without EECH 5 13 Exit Discarding CA EEN 5 13 fosa Optimal EE 5 13 Egad CUSTOM DES TEE EE 5 13 Save CUSTOM Deals ata E ce cela hort E AAA AA AA ARA 5 14 Decard CORTES ii ee 5 14 Bieielecle tl aie Mica a BIO EE 5 14 A Regulatory Approval Statement ccoiiocococc ce seeeces ec seedeneescenenneeeaneantsensssnieessassrnsesaseseenesaecne A 1 1 Introduction The MPC 2000 series of panel computers features advanced Intel processors 3rd generation Ivy Bridge Core or Celeron matched with 4 GB of system memory delivering a reliable high performance platform of wide versatility for use in industrial marine environments With its RS 232 422 485 serial NMEA 0183 and Gigabit Ethernet LAN ports the MPC 2000 series supports a wide variety of serial and marine specific interfaces for high speed network communications all with native network redundancy The MPC 2000 series comes with a range of standard display enhancements useful in industrial environments including O to 100 full range dimming 178 178 wide viewing angles optional optical bonding and or a multi touch touch screen as well as Moxa s innovative SavvyTouch display controls The MPC 2000 series panel computers are compliant with key industrial marine standard
26. folder M mcs7840_7820_Win _64bit_driver_v1 4 7 19_WHOL UL 6 UART MC57840_7820 Vin _64bit_driver_v1 4 7 19 WHOL File Edit View Tools Help Organize e 323 Views e Open Burn Favorite Links SS T IEA A win 4_AMD 2 19 2013 11 29 File Folder EI Documents 99710_7840_QUADP 7 19 2009 12 32 Application 366 KB E Pictures E Installation_Notes 7115 2011 2 47PM Text Document 1KB Bi Music MSSetup QUADPORT 4 27 2010 2 32 PM Application D Recently Changed E Release Notes 7115 2011 2 47PM Text Document 21KB L Searches Je Public 4 15 MPC 2000 Series Hardware Driver Installation and Configure 2 Click Install High Speed USB MultiSerial Device Drivers Setup Multitenal Device For Cancelling the Installation press Exit button oe Press Install button to Install the drives for High Speed USB Exit 3 Click Exit High Speed USB MultiSerial Device Drivers Setup need to restart the machine Unplug and Replug the Device if it is e Installation completed Press Est to terminate the application No current connected el Device Manager File Action View Help E WIN SNOYS0O5OGIH 2 1 Computer a Disk drives E Display adapters 42 DVD CD ROM drives ks Human Interface Devices Eq IDE ATA ATAPI controllers 5 Keyboards D Mice and other pointing devices Y Multi port serial adapters 2 High Speed USB MultiSerial Compound Device II MOXA CP 118U Series PCI Bus ELSE Netwo
27. ge to the system motherboard may occur The minimal distance that must be maintained between the heat sink and another heat source is 150 mm Do NOT install the unit horizontally for example lying down on its back as heat cannot be dissipated effectively and may cause damage to the LCD panel To ensure adequate heat dissipation install the unit vertically or within a 40 degrees slope off the vertical Exposure to extreme direct sunlight may cause a considerable increase in the temperature of the unit and under certain circumstances might lead to overheating Take this into consideration when bridge equipment is being planned for example sun shades distance from the windows and ventilation Exposure to strong vibration or loud chronic noise might affect functionality and or product lifespan It is advised to take vibration and noise into consideration during system assembly and installation so that the mount point may be carefully selected to avoid exposure to undue vibration For maximum safety at least two persons should work together to lift place and fasten the computer at its mount point Before you lift or move the computer make sure that the system is turned off and no power is being supplied to the system In addition make sure that you have prepared the correct screws for mounting CORRECT Handling Improper Handling j op Place the computer face down on a non abrasive surface Do not stress the corners nor place
28. he bottom panel You can connect USB devices such as a mouse or keyboard or an external storage drive to the USB ports MPC 2240 MPC 2260 USB 2 0 x 4 3 15 MPC 2000 Series Hardware Hardware Installation and Connection Installing a SATA Storage Drive You can install a SATA hard disk drive HDD or sold state drive SSD in the MPC 2000 series For added reliability we recommend that you install an SSD in the MPC 2000 series The procedure to install a SATA storage drive varies depending on your MPC 2000 series model On the MPC 2260 or MPC 2240 To install a SATA storage drive in an MPC 2260 or MPC 2240 panel computer complete the following steps NOTE 1 Locate the storage trays on the bottom panel of the computer For ease of installation we recommend that you place the MPC 2260 or MPC 2240 on a non abrasive surface with its display panel facing down Use the protection key to unlock the storage tray cover Lift the lever to open the storage tray cover Orient the SATA storage face up drive and insert it into the slot Push the lever to close the storage tray cover Protection Lock If you are unable to properly secure the SATA storage drive in the storage tray check that you have inserted the SATA storage drive correctly 6 Use the protection key to lock the storage tray cover and secure the SATA storage drive in place 7 To install the second SATA storage drive repeat steps 1 to 6 Make s
29. he user may be required to take adequate measures
30. indows Embedded Standard 7 Windows XP SP3 models with OS pre installed available by request System Chipset ntel BD82HM65 platform controller hub System Memory 4 GB pre installed 1 slots of 4 GB DDR3 1066 204 pin SO DIMM SDRAM USB USB 2 0 hosts x 4 type A connectors supporting system boot up Storage 2 SATA III connectors BIOS 64 Mbit Flash BIOS SPI type ACPI function supported Graphics Controller ntel HM65 Express chipset built in Video Output DVI D x 1 VGA x 1 female Digital nput Output 4 Dis 4 DOs or 8 Dis 8 DOs optional LPT Port 1 available on request Buzzer 75 to 85 db IEC 60945 compliant Other Peripherals Audio Line in and line out interface with 3 5 mm mini jack KB MS 2 PS 2 interface supporting standard PS 2 keyboard and mouse Display Panel Size 19 inch wide viewable image size Panel Type MVA Aspect Ratio 5 4 Pixels 1280 x 1024 SXGA Response Time 20 ms Contrast Ratio 2000 1 Light Intensity 300 cd m Viewing Angles 178 178 Active Display Area 376 32 H x 301 06 V mm Max Colors 16 7M 8 bits color Display I nterface Dual channel LVDS Resolution e VGA 640 x 480 e SVGA 800 x 600 e XGA 1024 x 768 e SXGA 1280 x 1024 Ethernet I nterface LAN 2 auto sensing 10 100 1000 Mbps ports RJ 45 Magnetic Isolation Protection 1 5 kV built in Serial Interface Serial Standards 2 RS 232 422 485 ports software selectable DB9 male 1 7 MPC 2000 Series
31. indows system3 difxapi dll Deleting Registry Key HKLM SOFTWARE Microsoft Windows CurrentVersion Uninstall HDMI Deleting Registry Key HKLM SOFTWARE Intel IGDI Creating Process C Users moxa ApoData Local Temp pft0960 tmp OpencCL OcLSetup exe Next gt Intel Installation Framework 4 4 MPC 2000 Series Hardware Driver Installation and Configure 8 Click Next to continue Intel Installation Framework Intel HD Graphics Driver Setup Progress Please wait while the following setup operations are performed Copying File C WWindows lsystem32Wdifhcapi dll Deleting Registry Key HELMISOFTWAREMicoosoft Windows CurrentVersion Uninstall HDMI Deleting Registry Key HELMISOFTWAREYntelVIGDI Creating Process C Users moxa AppData Local Temp pftD9B0 tmp OpencCL OCLSetup exe Creating Process C Users moxaAppDatalLocallTemplpAD9BO tmp1CCSSetupICCS exe Deleting File C ProgramData Microsoft Windows Start Menu Programs Intel Intel R HD Graf Deleting File C PProgramDataMicrosoftWindows Start MenulPrograms Intel R HD Graphics Deleting File C PProgramDiataMicrosoftWindows Start MenulPrograms Intel R Graphics and Deleting File C Users Public Desktop Intel R HD Graphics Control Panel Ink Deleting File C Users PubliclDesktop Intel R Graphics and Media Control Panel nk Click Next to continue T Setup Is Complete You must restart this computer for the changes to take effect Would you like to restart th
32. ive Before upgrading the BIOS you must first create a bootable USB storage drive for system upgrade You may use any software that to create a bootable USB drive We use Rufus as an example in this section 1 Start Rufus and select the USB device from the Device drop down list Rufus 1 3 4 270 2 Select MBR partition scheme for BIOS or UEFI computers to boot from legacy BIOS or UEFI Fartition scheme and target system type 3 Select FAT Default from the File system A ae File system FAT Default drop down list 4 Select 16 kilobytes Default from the Cluster size SR drop down list 16 kilobytes Default k i i l d lume label 5 Enter a drive name in the New volume label field BOO E 6 Check Quick format Create a bootable disk using Format Options 7 FreeDOS and Create extended label and icon check device For bad blocks files Quick Format Create a bootable disk using TA 7 Click Start to format and create the bootable USB Create extended label and icon files drive devices found ATTENTION We recommend that you use a USB drive with less than 2 GB of storage capacity A USB drive with bigger storage capacity may not support FAT file format and consequently may fail to boot 5 14 MPC 2000 Series Hardware BIOS Setup Step 2 Prepare the Upgrade File You must use the BIOS upgrade installation file to upgrade the BIOS Contact Moxa s technical department for assistan
33. lete the computer automatically restarts Access the BIOS Setup screen to verify the BIOS version on Main page The following figure shows an example ATTENTION Do NOT turn off the power supply during the BIOS upgrade process Doing so may interrupt the upgrade process and cause damage to the mainboard 5 16 A Regulatory Approval Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device C must accept any interference received including interference that may cause undesired operation Class A FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense European Community Warning This is a class A product In a domestic environment this product may cause radio interference in which case t
34. m For a secure mounting use all 14 clamps for MPC 2260 and MPC 2240 models or 10 C Tolorence 1 mm clamps for MPC 2190 models The clamp B MIN Thickness Behind Wall arms are fastened into slots on all four sides of gw l the MPC 2000 series display Modeli A B C D Mounting kits pcs __MPC 2260 140mm 81 3mm 609 0mm 4230mm 4 MPC 2240 11 0mm 650mm 5810mm 3740mm 14 MPC 2190 120mm 650mm 411 0mm 3680mmf 10 To fasten the clamp arms to the MPC 2240 mounting slots as shown in the following figure use the short M4 SUS stainless screws Then use the clamps to fasten the display to its mounting point Note the torque values shown in the figure Long screw M4x25mm SUS with cushion Torque 5 kgf cm Short screw M4 SUS with spring washer and flat washer Torque 5 kgf cm Wall mounting clamps CC LC Ly Mounting Kits Section VESA Mounting The MPC 2000 series also comes with an optional VESA mounting kit Six flat headed screws and four round screws are required to fasten the VESA mounting bracket See the following figure for detailed screw specifications and torque values Four additional screws not included in the kit are required to mount the unit on a VESA rack Use M6 screws with a length between 10 and 12 mm 3 5 MPC 2000 Series Hardware Hardware Installation and Connection MPC 2260 Round screw M4x4mm SUS Torque 5 kgf cm Flat screw M4x4mm SUS
35. n Moxa Americas Toll free 1 888 669 2872 Tel 1 714 528 6777 Fax 1 714 528 6778 Moxa Europe Tel 49 89 3 70 03 99 0 Fax 49 89 3 70 03 99 99 www moxa com su ort Moxa China Shanghai office Toll free 800 820 5036 Tel 86 21 5258 9955 Fax 86 21 5258 5505 Moxa Asia Pacific Tel 886 2 8919 1230 Fax 886 2 8919 1231 Table of Contents De d e UL O d Vu EE 1 1 EENEG 1 2 Package Checklist eee td 1 2 Product FOatUreS nt ii RO E E O AO NN 1 3 Hardware SPECIHCIUON cool oro 1 3 MPC 2260 Models iaa aaa EE EEN 1 3 MAPEO EE 1 5 MPC2190 ee 1 7 Optional Features for the MPC 2000 Geres cnn nn rr 1 9 AI O oil 1 9 Za Hardware tere NNNNNeeKEN NENNEN ENNEN NNN NNN NEEN NENNEN nai 2 1 AU eeh hh eh eh e aaa ad 2 2 PROG EE 2 2 A O 2 2 DIME e EE 2 3 MPC 2 26 Orei RO 2 3 MPC 2240 nuai aaa eet aaa aaa a ade adaa ada adada dadadada 2 3 MIRC E219 0 WEE 2 4 Savvy Louch Display CONTON BULONS incaseis cvs as duress ees Wadia ER 2 4 Sek en ere 2 5 3 Hardware Installation and Connection see KKK KENNEN rca 3 1 Hmstalation ANA Handling NOTES a esas 3 2 BIZ ele Wei Lange iii cdi caidas ci 3 3 lt e Ee e Le EE 3 5 VE SA MOTIN O A In A 3 5 A A 3 9 Grounding the MPC 2000 Series Panel Conti a 3 9 Powering On the MPC 2000 Series un aida 3 10 F werng OF thexMPG EE e ee de 3 10 Savvy LOuCh DISPLAY CONTO EE 3 10 Connecting Data Transmission Cables 00occcoccccccccnnncncnccannnnnnn cnn rr rn rr 3 12 Connecting
36. nding MPC 2267X 26 inch fanless panel computer with Intel Core 7 3517UE 1 7 GHz processor NMEA 0183 RS 232 422 485 serial ports Gigabit Ethernet LAN ports USB 2 0 ports dual AC DC power inputs and tape bonding MPC 2240X 24 inch fanless panel computer with Intel Celeron 1047UE 1 4 GHz processor NMEA 0183 RS 232 422 485 serial ports Gigabit Ethernet LAN ports USB 2 0 ports dual AC DC power inputs and tape bonding MPC 2240Z 24 inch fanless panel computer with Intel Celeron 1047UE 1 4 GHz processor NMEA 0183 RS 232 422 485 serial ports Gigabit Ethernet LAN ports USB 2 0 ports dual AC DC power inputs tape bonding and projected capacitive touchscreen MPC 2247X 24 inch fanless panel computer with Intel Core 7 2610UE 1 5 GHz processor NMEA 0183 RS 232 422 485 serial ports Gigabit Ethernet LAN ports USB 2 0 ports dual AC DC power inputs and tape bonding MPC 2190X 19 inch fanless panel computer with Intel Celeron 1047UE 1 4 GHz processor NMEA 0183 RS 232 422 485 serial ports Gigabit Ethernet LAN ports USB 2 0 ports dual AC DC power inputs and tape bonding MPC 2190Z 19 inch fanless panel computer with Intel Celeron 1047UE 1 4 GHz processor NMEA 0183 RS 232 422 485 serial ports Gigabit Ethernet LAN ports USB 2 0 ports dual AC DC power inputs tape bonding and projected capacitive touchscreen MPC 2197X 19 inch fanless panel computer with Intel Core i7 3517UE 1 7 GHz processor NMEA 0183 RS 232 422 485 serial ports
37. nfigure the parallel port Parallel Port lt Disabled gt Parallel Port This item allows you to configure the parallel port Options Disabled default 378 1 RQ7 5 4 MPC 2000 Series Hardware BIOS Setup Mode This setting allows you to configure the mode for the parallel port Options SPP default EPP ECP EPP ECP HDC Configuration You can set the host drive controller in IDE legacy default or AHCI mode The following screen appears when you select the legacy IDE mode HDD Detect Delay Time lt 0 Second gt F5 F6 Enter HDD Detect Delay Time This setting allows you to set the time delay when detecting hard disks Option O default 1 2 3 seconds Serial ATA Port O to 1 This setting allows you to display information about the installed drives AHCI SALP Note that AHCI SALP only appears when you select the AHCI mode This setting allows you to enable Aggressive Link Power Management SALP in AHCI for the host bus adapter to conserve power by detecting when a SATA drive is no longer processing information and then immediately setting it to suspended or sleep mode without waiting for the software to initiate power down processes Host Capability Register bit 26 Options Enabled default Disabled 5 5 MPC 2000 Series Hardware BIOS Setup SATA Port 0 to 1 HotPlug This item allows you to enable disable hotplug capabilities the ability to remove the drive while the computer is
38. nges This item allows you to exit the BIOS environment and save the values you have just configured Options Yes default No Save Change without Exit This item allows you to save changes without exiting the BIOS environment Options Yes default No Exit Discarding Changes This item allows you to exit without saving any changes that might have been made to the BIOS Options Yes default No Load Optimal Defaults This item allows you to revert to the factory default BIOS values Options Yes default No Load Custom Defaults This item allows you to load custom default values for the BIOS settings Options Yes default No 5 13 MPC 2000 Series Hardware BIOS Setup Save Custom Defaults This item allows you to save the current BIOS values as a custom default that may be reverted to at any time by the load custom defaults selection just above Options Yes default No Discard Changes This item allows you to discard all settings you have just configured Options Yes default No Upgrading the Bl OS This section describes how to upgrade the BIOS However note that an improper BIOS update may damage the mainboard leaving the computer unable to boot We strongly recommend that you contact Moxa s technical support staff to obtain the necessary tools and the most current advice before attempting to upgrade the BIOS on any Moxa devices Step 1 Create a Bootable USB Storage Dr
39. on a coarse or gritty surface 3 2 MPC 2000 Series Hardware Hardware Installation and Connection Desktop Mounting The MPC 2000 series display comes with optional brackets that allow you to install the unit on a horizontal surface such as a desktop Three round screws are required for each bracket See the following figures for detailed screw specifications and the torque values 1 Flat screws M4x4mm Flat screws M4x4mm Torque 5 5 kgf cm Torque 5 5 kgf cm Flat screws M4x4mm Torque 5 5 kgf cm Torque 8 5 kgf cm 3 3 MPC 2000 Series Hardware Hardware Installation and Connection MPC 2260 and MPC 2240 MPC 2190 33 58 5 26 245 71 9 67 6 68 0 26 Place your MPC 2000 series display on a clean flat well ventilated desktop For proper ventilation leave some space between the MPC 2000 series display and other equipment Do NOT place equipment or objects on top of the MPC 2000 series display Doing so might damage internal components MPC 2000 Series Hardware Hardware Installation and Connection Panel Mounting The MPC 2000 series display comes with 14 Bomber Wall Cult Bien optional clamp mounts that enable you to an install the unit onto a wall where space has l p A MAX Wall Thickness been cut out to accommodate the rest of the hardware or into computing stations where a flush mount is needed The maximum thickness of the surface to which the unit can be clamped is 11 m
40. ows you to enable disable PXE boot to LAN function Options Disabled default Enabled Add Boot Options This item allows you to add the boot order options for shell network and Removables Options Last default First USB Boot This item allows you to enable disable USB boot function Options Enabled default Disabled 5 11 MPC 2000 Series Hardware BIOS Setup EFI Device First This item allows you to determine EFI device first or legacy device first If enabled EFI device will be the first if disabled legacy device will be the first Options Disabled default Enabled Boot Delay Time This item allows you to configure the delay time value for users to input hot key during POST time Options O Second default 3 Seconds 5 Seconds 10 Seconds Legacy Normal Boot Menu This item allows you to configure the boot menu Options Normal default Advance Boot Type Order This item allows you to select the boot order Use F5 F6 to change values Options Hard Disk Drive default CD DVD ROM Drive USB Others Hard Disk Drive USB Drive This item allows you to view installed devices such as hard disk drives USB drives or CD ROMs For example if you have inserted a USB drive into the computer it will appear here 5 12 MPC 2000 Series Hardware BIOS Setup Exit Settings The section allows users to exit the BIOS environment Exit Saving Changes F5 F6 Enter Exit Saving Cha
41. p until you have touched a circle in each corner 15 Click OK 4 points calibration completed Press Ok to continue 4 11 MPC 2000 Series Hardware Driver Installation and Configure Performing Screen Calibration Note that you have to do 4 points calibration each time you change the display resolution This enables the touch function to work properly To perform 4 points calibration complete the following steps 1 Double click the eGalaxTouch icon on the desktop eGalaxT ouch General Setting Tools Display Hardware About Linearization Curve Do 4 points alignment to match display Clear linearization parameter and do 4 points alignment Do points linearization for better touchscreen linearity Do draw test to venfy the touch accuracy 3 The system displays a circle at each corner of the screen Touch the center of the circle until the screen displays OK Repeat this step until you have touched a circle in each corner Ok 4 Click OK to complete the calibration O 4 points calibration completed Press Ok to continue 4 12 MPC 2000 Series Hardware Driver Installation and Configure MPC 2260 MxGenerall o Driver Installation Installing the MxGenerall o Driver 1 Run the executable program MxGenerallo_W7_x64 exe elcome to the InstallShield Wizard for freier W7_x64 The InstaliShield R Wizard will instal MaGenerallo_W7_x64 on your computer To continue dick
42. rect type of battery Contact the Moxa RMA service team if you need to replace the battery 2 5 3 Hardware Installation and Connection This chapter describes how to connect the MPC 2000 series to the network and to other devices The following topics are covered in this chapter O Installation and Handling Notes gt Desktop Mounting gt Panel Mounting gt VESA Mounting Wiring Requirements Grounding the MPC 2000 Series Panel Computer Powering On the MPC 2000 Series Powering Off the MPC 2000 Series n DU D gt SavvyTouch Display Controls a Connecting Data Transmission Cables gt Connecting to the Network gt Connecting Serial Devices gt Connecting NMEA 0183 Devices Connecting Speakers or Headphones Connecting a PS 2 Keyboard and Mouse Connecting to USB Devices n DU D Installing a SATA Storage Drive gt On the MPC 2260 or MPC 2240 gt On the MPC 2190 MPC 2000 Series Hardware Hardware Installation and Connection Installation and Handling Notes Before installing or mounting the MPC 2000 series panel computer read the following notes 1 The MPC 2000 series is designed for mounting on a desktop wall or an FDMI VESA interface Refer to the illustrations in the related sections for detailed instructions To prolong product lifespan good ventilation must be maintained around the machinery The chassis heat sink area MUST be kept clear from other heat generating items otherwise dama
43. rk adapters Bn E Intel R 825741 Gigabit Network Connection fu e Intel R 82579LM Gigabit Network Connection fu e Realtek PCIe GBE Family Controller E e Realtek PCIe GBE Family Controller 2 po Other devices i i z Ports COM ALP Update Driver Software ia Processors Disable JI Security Devices Uninstall i Sound video an Ke Storage controll Ku System devices g Universal Serial Scan for hardware changes Launches the Update Driver Software Wizard for the selec 4 16 MPC 2000 Series Hardware Driver Installation and Configure 5 Select Search automatically for updated driver software E Update Driver Software Unknown Device z x ae J Update Driver Software Unknown Device How do you want to search for driver software Search automatically for updated driver software Windows will search your computer and the Internet for the latest driver software for your device Browse my computer for driver software Locate and install driver software manually Cancel 6 Select Don t Search online E Update Driver Software Unknown Device j l xx G 0 Update Driver Software Unknown Device Allow Windows to search online for driver software for your Unknown Device gt Yes always search online recommended Windows will automatically search for the latest drivers and applications for your hardware and download them to your computer Yes sear
44. running for installed storage drives Options Disable default Enabled Video Configuration This item allows you to configure the internal graphics device 1GD for things like memory allocation DVMT and monitor types Boot Type Internal Graphics Device internal Graphic Device F5 F6 Enter 5 6 MPC 2000 Series Hardware BIOS Setup IGD DVMT Pre Allocated This item allows you to configure pre allocated memory capacity for the IGD Pre allocated graphics memory is invisible to the operating system Options 64 MB default 32 MB 96 MB 128 MB 256 MB 512 MB DVMT is a BIOS solution where the optimum amount of memory is dynamically allocated and de allocated as needed for balanced graphics and system performance through Intel Direct AGP and a highly efficient memory utilization scheme DVMT ensures the most efficient use of available system memory resources for maximum 2D 3D graphics performance IGD DYMT Pre Al located lt 64 MB gt F5 F6 Enter IGD DVMT Size This item allows you to configure the maximum amount of memory DVMT will use when allocating additional memory for the internal graphics device Options 256 MB default 128 MB Max IGD Boot Type This item allows you to select the video device which will be activated during POST Options VBIOS Default default VGA DVI Integrated Panel 5 7 MPC 2000 Series Hardware BIOS Setup Chipset Configuration This item allo
45. s e 1 g DNV 2 4 random wave 3 100 Hz 2 5 hr per axis e 1g DNV 2 4 Class C sine wave 2 50 Hz 1 Oct min 1 5 hr per axis Power Requirements Input Voltage 115 to 230 VAC 50 60 Hz 24 VDC Power Consumption 40 Wto 125 W max Standards and Certifications Safety UL 60950 1 CCC EMC EN 55022 Class B EN 55024 4 2 EN 55024 4 3 EN 55024 4 4 FCC Part 15 Subpart B Class A Marine Standard EC 60945 4th EC 61162 EC 61174 Marine Type Approval DNV 2 4 and IACS E10 ABS MR A003 Green Product RoHS cRoHS WEEE 1 8 MPC 2000 Series Hardware Introduction Reliability MTBF mean time between failures 202 309 hrs Automatic Reboot Trigger Built in WDT watchdog timer supporting 1 255 levels for time interval system reset software programmable Warranty Warranty Period 1 year Details See www moxa com warranty Optional Features for the MPC 2000 Series Intel Celeron processor 1047UE 2M Cache 1 40GHz TDP 17 watts Options e Intel Core 3 processor 3217UE 3M Cache 1 60GHz TDP 17 watts p e Intel Core i7 processor 3517UE 4M Cache 2 80GHz TDP 17 watts Options Windows 7 Professional Windows XP Embedded Windows Embedded Standard 7 Windows XP SP3 Factory For MPC 2190 and MPC 2240 Projected capacitive touch screen multi touch USB interface Options Optical bonding Color calibrated for ECDIS Customized options for SSD drives Hardware Block Diagram Intel CPU DDR3 SODIMM DVI D R
46. s such as IEC 60945 4 IEC 61174 IEC 61162 DNV2 4 and ACS E10 validating their resilient durability in marine operations An optional P65 rated unibody housing provides added protection against the harsh conditions found in marine environments The MPC 2000 series delivers a rugged type approved high performance and user friendly panel computer perfect for ECDIS navigation systems and other marine IBS applications The following topics are covered in this chapter O Overview O Package Checklist O Product Features O Hardware Specifications gt MPC 2260 Models gt MPC 2240 Models gt MPC 2190 Models gt Optional Features for the MPC 2000 Series O Hardware Block Diagram MPC 2000 Series Hardware Introduction Overview The MPC 2000 series panel computer range is a flexible all in one computer and monitor solution designed for type approved use in industrial marine environments where reliability and durability are key requirements The MPC 2000 series features Smart OSD Control LED backlight technology full dimming and multi power In addition you can select options such as SSD storage devices multiple interface configurations and operating systems The models available in the MPC 2000 series are listed below MPC 2260X 26 inch fanless panel computer with Intel Celeron 1047UE 1 4 GHz processor NMEA 0183 RS 232 422 485 serial ports Gigabit Ethernet LAN ports USB 2 0 ports dual AC DC power inputs and tape bo
47. sable to label all wires used in the system ATTENTION Safety First Be sure to disconnect the power cord before installing and or wiring your MPC 2000 series panel computer Wiring Caution Calculate the maximum possible current in each power wire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat causing serious damage to your equipment Temperature Caution Be careful when handling the unit When the unit is plugged in the internal components generate heat and consequently the outer casing may feel hot to the touch We recommend taking the following precautions to minimize heat build up within the display e Position the display within 40 of the vertical e Install an external fan to increase airflow upwards through the display if a the display is not positioned within 40 of the vertical b the ambient temperature exceeds 25 C or c the display is used ina location with minimal ventilation Important Safety Precaution Even though the display is rated to operate within the IEC 60945 standard of 15 to 55 C for marine applications it is best to ensure that the ambient temperature does not exceed 25 C Doing so will increase the life of your display and minimize service costs Grounding the MPC 2000 Series Panel Computer Before you power on the MPC 2000 series first Grounding Connector
48. the aspect ratio To configure adjust the image by moving the scrolling bars Intel HD Graphics Control Pane Display Caplay Settings Select Display F bs Advarced Digital Display EXPC 14u Forpolurticn T Previse D EE 155011004 w Display Profiles Cunrer Settings i e Beirezh habe LE 60p Hz K Ratatat T wo 50 180 170 Sealing ih Maintain Depia Sepir v Customize Aspect Ratio 5 Click Apply to save the changes Installing the Touch Screen Driver For touch screen models you must install the driver for the touch function 1 On the software CD go to the CD drive Driver 7 Touch INN T Touch eGalaxTouch_ _ Vista XP 2K 51105815 Diganize Al Open Share with New Folder Ss e E g a h Jate mode lype Sue O Name L vp or Favorites Fd erala Touch 510 9126 26 2014 3 34 DM File folder A Libraries E Computer EL Local Disk C 2 Double click setup to start the installation 4 7 S K J J eGalaxTouch_7_Vista XP_2K_5 1 eGalaxTouch_5 11 0 9126 Organize v Open New folder DW Name i Date modified Type Size e global 2 6 2014 3 34 PM File folder Libraries de 164 2 6 2014 3 34 PM File folder de 86 2 6 2014 3 34 PM File folder E Computer Setup dl 5 17 2006 11 21 AM Application extens 161 KB amp Local Disk C E datal 5 26 2011 12 22 PM Cabinet File 563 KB e USB DISK D _ datal hdr 5
49. the motherboard chipset and VGA subsystems and components When the panel computer is working properly the screen displays Pass for each subsystem component as shown in the figure The screen displays Error to indicate that a faulty component The CPU memory chipset and VGA components are detected only during the boot process The AC and motherboard power components are being monitored continuously system Status AC Input Power Pass M B Power Pass CPU Pass Memory Pass Chipset Pass VGA Pass NOTE If the MPC 2000 series is powered using a DC converter the systems displays Error for the AC power status in the System Status screen This does not affect the operation of the MPC 2000 series System Status AC Input Power M B Power Pass ECDIS Mode Brightness Adjustment For ECDIS approved models you can use the ECDIS button to select an ECDIS display mode DAY DUSK or NIGHT The ECDIS mode setting overwrites the custom display settings you specified The ECDIS button and ECDIS related functions are disabled on standard MPC 2000 series models ECDIS Mode DAY DUSK NIGHT 3 11 MPC 2000 Series Hardware Hardware Installation and Connection cs Storage The storage icon blinks red when data is been accessed on the MPC 2000 series NOTE You can also control the MPC 2000 series using commands over the UART interface For detailed UART command description see Appendix B UART Commands for Display Control
50. to the Network A 3 12 EoOnnectingd oeral DEVICES tancia 3 13 Connecting NMEA OFE 7 DEVICES ee deel a DAA RAS 3 14 Connecting Speakers Or te le gie te EE 3 14 Connecting a PS 2 Keyboard ANd Mouse 3 15 Connecting to USB DEVICES siria arado tul a aaa dns 3 15 Installing a SATA Storage Drive 3 16 On the MPC 2200 0r MPO A o eleie 3 16 On dn RE NEE 3 17 4 Driver Installation and Configure ainia ee ENEE REESEN NENNEN 4 1 NS AS O A ney nA Are RMN Mani Gan Maer ara mare T E E U RCE T ENT RNE CORT oeUCCere 4 2 SeculhG Display RESONON ertrar aanne a n a a a lt 4 5 Installihg the Touch Screen DAVE es ee ee es VEE EA dead eee ead 4 7 PERO MINO Eege Ke tele e EE 4 12 MPE 22060 MXGen erallo Driver stat e eLo Tn 4 13 Installing the MxGenerallo Driver ER 4 13 MPE 2260 UAR Driver INSTA Nat ON EE EE 4 15 installing the VARTIDIIVET eege EE Ee 4 15 By BIOS SOU EE 5 1 Starting the BOSS et DUTY tn A a aio 5 2 Ma e ad Een EE 5 3 PANG ae de e EE 5 3 BOOE e edel ALI OM EE 5 4 Peribhetal COMMOUFAUO Mek cet el ad a fede ta ao A 5 4 A ne a ee erence errr ren nr eer rere eae ene 5 5 Lee eeh de leg el pee ame tree Meets e Ceererrretrrer reer AI 5 6 EE 5 8 Hardware MONITO ET 5 9 Keele EEN 5 9 SCE SUI A o 5 10 POWER lee Su AA A EE 5 10 Selen de e GER 5 11 BOOL TY Pa a A NN a e e e di iii ii ii bebe ed Bebe eiii dlrs 5 11 A ate neat eee eee ne eet at on a ae oe ee et ale esa octet eae E E eceees EAE a 5 11 ACA B OOO e EE 5 11 USB see em
51. troller Install AS232 interface driver InstallShield 4 8 MPC 2000 Series Hardware Driver Installation and Configure 6 Select a calibration option and click Next eGalaxTouch Setup Type Select the setup wpe that best suits your needs Do 4 point calibration after system reboot O Ever system boot up Nest system boot up None 7 To enable the touch screen function make sure that your touch controller s USB cable is connected to the MPC 2000 series Click OK to continue da earn O If you are trying to install the USB touch device please make sure that AR your touch monitor or touch controller s USB cable is plugged into the computer now Please close the Found New Hardware Wizard dialog when it appears 8 If required select Support Mulit Monitor System Click Next to continue eGalaxTouch Setup Type Select the setup wpe that best suits your needs IF you want to use Mult Monitor please check the box Z Support Multi Monitor System Back Next gt Cancel 4 9 MPC 2000 Series Hardware Driver Installation and Configure 9 Accept the default destination folder or click Browse to choose one then click Next eGalaxTouch Choose Destination Location Select folder where setup will install files Setup will install eGalasT ouch in the following folder To install to this folder click Next To install to a different folder click Browse and select another folder
52. ure that you have securely fastened the 8 door lever If you are installing only one SATA storage drive in the MPC 2000 series install the storage drive in the slot nearer to the display panel If you are installing two SATA storage drives install the first storage drive in the slot nearer to the display panel and the second storage drive in the other slot To remove a storage drive pull out the lever and push the tray door to the side to eject the SATA storage drive from the slot then remove the SATA storage drive from the computer 3 16 MPC 2000 Series Hardware Hardware Installation and Connection On the MPC 2190 To install a SATA storage drive in an MPC 2190 panel computer complete the following steps 1 Remove the seven screws on the back of the MPC 2190 2 Remove the back cover of the MPC 2190 and locate the four screw holes as indicated in the following figure for the storage drive Installation Area SATA Cable A ni D dd 3 17 MPC 2000 Series Hardware Hardware Installation and Connection 3 Use the screws to attach the brackets to the sides of the storage drive HDD or SSD Brackets Screws 4 Align the screw holes on the brackets with the screw holes in the installation area then install the screws to secure the storage drive in place as shown in the following figure 5 Connect the SATA cable to the storage drive LOCH MLL MM 000 SE L014041 Hid 025 gemia FLL ACA ON poy
53. wer Consumption 40 to 75 W Standards and Certifications Safety UL 60950 1 EMC EN 55022 Class B EN 55024 4 2 EN 55024 4 3 EN 55024 4 4 FCC Part 15 Subpart B Class A Marine IEC 60945 4th IEC 61174 IEC 61162 DNV2 4 ACS E10 Green Product RoHS cRoHS WEEE Reliability Automatic Reboot Trigger Built in WDT watchdog timer supporting 1 255 levels for time interval system reset software programmable Warranty Warranty Period 3 years for computer systems 1 year for LCD panels Details See www moxa com warranty MPC 2240 Models Computer CPU Intel Celeron Processor 1047UE 2M Cache 1 40GHz TDP 17 watts standard OS Windows 7 Professional Windows Embedded Standard 7 Windows XP Embedded Windows XP SP3 System Chipset Intel HM65 System Memory 8 GB capacity 4 GB pre installed 1 slot of 4 GB DDR3 1600 204 pin SO DIMM SDRAM USB 4 bootable USB 2 0 hosts type A connectors Storage 2 SATA III interfaces 6 Gbps 2 5 removable storage trays BIOS 64 Mbit Flash BIOS with SPI ACPI Graphics Controller ntel HM65 Express chipset built in Video Output 2 outputs 1 DVI D 1 VGA female Other Peripherals Audio line in out 3 5 mm mini jack KB MS 2 PS 2 interfaces supporting standard PS 2 keyboard and mouse Display Panel Size 24 viewable image size Panel Type MVA Aspect Ratio 16 9 Pixels 1920 x 1080 WSXGA Pixel Pitch RGB 0 276 H x 0 276 V mm Response Time 25 ms gray to gray
54. wn in the following figure This does not affect the normal operation of the MPC 2000 series System Status AC Input Power M B Power Pass SavvyTouch Display Controls The MPC 2000 series comes with five SavvyTouch display controls on the front panel These intelligent controls turn on as your hand draws near the area of the panel where they are located INFO Button MENU Button ECDIS INFO z D MENU soro on OM ONOM ON O ECDIS Button Brightness Button MENU Power Control On the MPC 2000 series the MENU button also serves as the power button To turn on or turn off the MPC 2000 series press the Menu button for about four seconds After the system is powered up the MENU button turns green To power off the MPC 2000 Series press the MENU button for about four seconds and then choose to enter standby hibernation or system shutdown mode the available choices may be configured using your operating system s power management settings If you encounter technical problems press and hold the MENU button for 10 seconds to force a hard shutdown 3 10 MPC 2000 Series Hardware Hardware Installation and Connection Brightness You can use the two brightness buttons to set the brightness of the screen Press the plus button to increase screen brightness and the minus button to decreas screen brightness INFO The INFO button displays a status report shown at right of the AC power supply main board CPU memory
55. ws you to configure the chipset settings Power ON after Power Fail F5 F6 Enter Power ON after Power Fail This item allows you to enable disable the computer form automatically powering up after a system crash Options ON default OFF Last State DO Level This item allows you to set the DO default level 5 8 MPC 2000 Series Hardware BIOS Setup Hardware Monitor This item allows you to view stats like CPU and system temperature voltage levels and other chipset information Security Settings This section allows users to configure security settings with a supervisor password Set Supervisor Password 5 9 MPC 2000 Series Hardware BIOS Setup Set Supervisor Password This item allows you set the supervisor password Select and then enter the password and then confirm the password again To delete the password enter Set Supervisor Password and then enter the old password then leave the new password fields blank and press enter Power Settings The section allows users to configure power settings Auto Wake on 5 lt Disabled gt 5 10 MPC 2000 Series Hardware BIOS Setup Boot Settings This item allows you to select the BIOS support boot device type Boot Type lt Dual Boot Type gt F5 F6 Enter Boot Type This item allows you to enable disable quick boot function Options Dual Boot Type default Legacy Boot Type UEFI Boot Type PXE Boot to LAN This item all
Download Pdf Manuals
Related Search