Temblor T10
Contents
1. Eris E8 Right Eris E8 Left 2 Hookup Temblor T10 2 2 Hookup Diagrams Owner s Manual LOW PASS FILTER 60Hz 80Hz 100Hz 50Hz 130Hz Temblor T10 Slave 3 Tutorials Temblor T10 2 2 Hookup Diagrams Owner s Manual 3 Tutorials 3 1 Subwoofer Placement The goal of proper subwoofer placement is to set up your system so that your subwoofer acts as a natural extension of your full range monitors without boosting the overall bass response of your room or exaggerating any one frequency or frequency range Because low frequencies are not directional that is humans cannot perceive the direction from which low frequencies are coming you aren t limited to placing it facing the mix position A quick way to find the best location for your subwoofer is to temporarily place it in the mix position and play some program material that contains a lot of bass Move around the half of the room where your full range monitors are positioned until you find the spot where the bass sounds its best Again it s important to remember that low frequencies are not directional so placing the subwoofer beside or behind you will not be an issue In general you will want to avoid placing your subwoofer too near to reflective surfaces like a wall or in a corner as this will exaggerate the bass energy and make your T10 sound boomy Once you find t2. Manual Pan the pink noise so that it only plays in the right speaker hard right and repeat step 6 for the right channel Turn your full range monitors off 9 Begin slowly increasing the input volume on your Temblor T10 until the acoustic level of the pink noise reaches 79 dB SPL on your SPL meter when measured at mix position 10 Set the lowpass filter on your T10 to 130 Hz This will create an overlap between your T10 s and your full range system s frequency responses 13 3 2 2 Tutorials Hookup Diagrams 11 Temblor T10 Owner s Manual Play pink noise through your full system and experiment with the polarity switch on your TemblorT10 to see which position provides the best bass response at your mix position Leave the polarity switch in the position that provided the loudest bass response This means that you subwoofer is in phase with your full range system Ifyou are using the 80 Hz highpass filter on the T10 to bandpass your full range monitors set the lowpass filter to 80 Hz If you are using an external highpass filter for your full range monitors set the lowpass filter to the appropriate frequency e g if your high pass filter is set to 100 Hz set the lowpass filter to the same frequency You may need to experiment with the Low Pass Filter setting on your subwoofer until you find the smoothest crossover position Once the Input Gain control is set on your full rang
3. or 220 240V 50 60 Hz CABINET Vinyl laminated MDF PHYSICAL Width 12 60 320 mm Depth 15 75 400 mm Height 15 75 400 mm Weight 39 46 lbs 17 9 kg 4 2 Block Diagram Left RCA input O a ge EE Laferas ligi l Z J LeftTRS Output Left XLR Input oS 93 Left XLR Output y High Pass Filter Right XLR Output Low Pass Filter WADA c Limiter cj p oto om E Sub Bypass Footswitch 16 4 Resources Temblor T10 4 3 Troubleshooting Owner s Manual 4 3 Troubleshooting No power First ensure that your Temblor T10 is plugged in If it s connected to a power conditioner verify that the power conditioner is turned on and functioning If it is yet there is still no power to the monitor contact PreSonus for a repair No audio If your Temblor T10 appears to power on but you hear no sound when playing audio from the mixer the lights are on but nobody s home first make sure that the cables connecting the mixer to the subwoofer are working correctly Also verify that the Input Gain control is set to provide enough amplitude for the signal Hum Usually hum is caused by a ground loop Verify that all audio equipment is connected to the same power source If you are not using a power conditioner we highly recommend that you add one Not only will this help to minimize hum it will better protect your equipment from power surges brownouts etc Try setting the Ground Lift switch to Lift This adds 1 kQ resist
4. this output set its Low Pass Filter control to its highest setting IEC Power Connection Your Temblor T10 accepts a standard IEC power cord Warning Do not remove the center grounding prong or use a separate ground lift adapter as this could result in electric shock Power Switch This is the On Off switch The power status is indicated by the illuminated logo on the front of the cabinet AC Select Switch The input power voltage is set at the factory to correspond with the country to which it was shipped Use this switch only if you are using your Temblor T10 in a country that uses a different standard voltage than is used in the country where you purchased your T10 2 Hookup Temblor T10 2 1 Rear Panel Connections and Controls Owner s Manual 2 1 4 User Controls SUB Bypass footswitch Sub Bypass Connect the bypass footswitch cable to this 1 4 input Stepping on the footswitch will bypass the subwoofer highpass filter and Sub Out altogether This will allow the signal from your audio source to pass directly through your Temblor T10 to your full range studio monitors and allow you to compare your mix without subharmonic frequencies While bypass is active the LED on the front of your T10 will flash between red and blue The footswitch is latching so the bypass remains in effect until you step on it again Power User Tip The T10 s Sub Bypass function is a conveni
5. Temblor T10 Active Studio Subwoofer Owner s Manual Q Co IIB PreSonus Table of Contents 1 1 1 1 2 1 3 Overview 1 Introduction 1 Summary of Temblor T10 Features 2 What is in the box 2 Hookup 3 Rear Panel Connections and Controls 3 2 1 1 Inputs 3 2 1 2 Outputs 4 2 1 3 Power 4 2 1 4 User Controls 5 2 2 4 1 4 2 4 3 4 4 Hookup Diagrams 7 2 2 1 Basic Setup 7 2 2 2 Advanced Setup 8 Tutorials 10 3 1 Subwoofer Placement 10 3 2 Level Calibration 71 Resources 15 Technical Specifications 15 Block Diagram 16 Troubleshooting 17 PreSonus Limited Warranty 18 1 Overview Temblor T10 1 1 Introduction Owner s Manual 1 1 Introduction Thank you for purchasing the PreSonus Temblor T10 active studio subwoofer PreSonus Audio Electronics has designed the T10 utilizing high grade components to ensure optimum performance that will last The Temblor T10 is an active subwoofer with a 10 inch glass composite driver high temperature voice coil and damped rubber surround in a ported cabinet which allows the subwoofer to produce higher volume up to 113 dB SPL with less power than a sealed box design Featuring a variable 50 to 130 Hz lowpass filter the Temblor T10 can be dialed in to pair perfectly with full range studio monitors making it the ideal solu
6. ance to the ground of the balanced inputs and often eliminates hum Use balanced cables whenever possible If your audio device does not offer a balanced output you can connect it to the unbalanced RCA inputs on the Temblor T10 or you can connect it to a DI direct injection box which will provide a ground lift switch and a balanced output Finally make sure that your audio cables are not run near power cables and use cables that are the appropriate length for your application Using cables that are too long not only increases the risk of noise itincreases the likelihood that the cables are coiled which will essentially create an antenna that picks up all kinds of audio interference 17 4 Resources Temblor T10 4 4 PreSonus Limited Warranty Owner s Manual 44 PreSonus Limited Warranty PreSonus Audio Electronics Inc warrants this product to be free of defects in material and workmanship for a period of one year from the date of original retail purchase This warranty is enforceable only by the original retail purchaser To be protected by this warranty the purchaser must complete and return the enclosed warranty card within 14 days of purchase During the warranty period PreSonus shall at its sole and absolute option repair or replace free of charge any product that proves to be defective on inspection by PreSonus or its authorized service representative If you are located in the USA and need warranty repair please subm
7. e set the Low Pass Filter control to the lowest frequency that your main studio monitors can reliably reproduce Note that this control only affects the signal going to the internal amplifier and the Sub Out output and does not affect the main outputs If you daisy chain two T10s set the second one s lowpass filter to its highest setting 130 Hz to make sure it reproduces everything it gets from the first T10 Ground Lift Switch In the Lift position this switch adds 1 kQ resistance to the ground for the balanced inputs The Ground Lift switch doesn t affect the AC mains safety ground for the power supply Power User Tip Enabling the ground lift can help to reduce ground loop noise in your audio system Ground loops can be caused by running audio cables with power cables by older buildings with improper wiring or by equipment that generates a lot of RFI such as computers laptop power supplies and the like 2 Hookup Temblor T10 2 2 Hookup Diagrams Owner s Manual 2 2 Hookup Diagrams 2 2 1 Basic Setup FU Sceptre S6 Right Sceptre S6 Left 2 Hookup Temblor T10 2 2 Hookup Diagrams Owner s Manual 2 2 2 Advanced Setup Footswitch Temblor T10 Master
8. e monitors and T10 leave it alone don t use it as a volume control Leave that job to your audio device s output level control 14 4 Resources Temblor T10 4 1 Technical Specifications Owner s Manual 4 Resources 4 1 Technical Specifications INPUTS 2 Balanced XLR 2 Balanced 14 TRS 2 Unbalanced RCA OUTPUTS 2 Balanced XLR full range with 80 Hz HPF option 2 Balanced 4 TRS full range with 80 Hz HPF option 1 Balanced XLR Sub Out PERFORMANCE Frequency Response 20 Hz 200 Hz Low Pass Filter Frequency 50 130 Hz variable Signal to Noise Ratio gt 98 dB THD 0 019 power lt 160W Amplifier Power 170W RMS 250W Peak Power Consumption 230W Amplifier Type Class AB Peak SPL at 1m 113 dB Woofer 10 glass composite USER CONTROLS Input Gain Control 30 to 6 dB Polarity Switch 0 or 180 Low Pass Filter Control 50 Hz to 130 Hz Ground Lift Switch On Off High Pass Filter Switch On Off Bypass Footswitch On Off PROTECTION RF interference Output current limiting Over temperature Turn on off transient Subsonic filter External mains fuse 15 4 Resources Temblor T10 4 2 Block Diagram Owner s Manual POWER 100 120V 50 60 Hz
9. ent way to make sure your mix will sound good on systems with and without a subwoofer Bypassing the subwoofer will let you hear how the mix sounds without it After all many listeners will be using two speakers without a sub and you want your mix to sound just as good in a stereo system Polarity The Polarity button reverses the polarity of the summed input signal High Pass Filter Removes frequency content below 80 Hz from the full range signal sent from the T10 outputs This is useful if your main studio monitors do not have their own high pass filter The highpass filter is also bypassed when the sub bypass is enabled Power User Tip Leaving frequency content below 80 Hz in full range studio monitors can introduce destructive cancellations with the highest frequencies that are reproduced by the Temblor T10 Conversely this can reinforce these frequencies and make your mix seem to have more bass in it than it actually does By rolling off your full range speakers you will create a more linear frequency response between the subwoofer and full range content 2 Hookup Temblor T10 2 1 Rear Panel Connections and Controls Owner s Manual LOW PASS FILTER 60Hz 50Hz 130Hz Lift Low Pass Filter This control determines the upper end of the frequency range reproduced by the Temblor T10 If you have enabled the onboard highpass filter set the Low Pass Filter control to the same value Otherwis
10. he place in the room where the bass sounds the smoothest place your T10 in that spot return to the mix position and listen to it again You may need to adjust the location just keep making small adjustment a foot or so at a time until the bass response sounds as even as possible Don t locate your T10 where it will exaggerate frequencies as this will have the opposite effect on your mix For example if your system has a bump around 100 Hz what you hear will not accurately reflect what is in your mixes resulting in less kick drum punch than you wanted 10 3 Tutorials Temblor T10 2 2 Hookup Diagrams Owner s Manual 3 2 Level Calibration Matching the levels of the all studio monitors in your system is an easy extra step that will help you to achieve an optimal listening environment You will need an SPL meter to do this luckily there are many inexpensive and free SPL meter apps for just about every type of smartphone that will do the job nicely Below is a brief tutorial on how to level match your monitors Note Make sure that any effects processors such as EQs compressors and reverbs have been bypassed You ll want a clean signal 1 Connect your studio monitors and Temblor T10 as shown in the hook up diagram in Section 2 2 1 2 Turn your Temblor T10 and your full range studio monitors input levels to their lowest setting INPUT GAIN 8 30dB 6dB 3 Play pink noise through your primary audio source s ou
11. imbit Notion PreSonus QMix Al StudioLive and XMAX are trademarks or registered trademarks of PreSonus Audio Electronics Inc Capture Impact Mixverb Presence RedLightDist SampleOne Studio One and Tricomp are trademarks or registered trademarks of PreSonus Software Ltd Mac and Mac 0S are registered trademarks of Apple Inc in the U S and other countries Windows is a registered trademark of Microsoft Inc in the U S and other countries Other product names mentioned herein may be trademarks of their respective companies All specifications subject to change without notice except the recipe which is a classic Temblor T10 Active Studio Subwoofer Owner s Manual WB Co 18011 Grand Bay Ct Baton Rouge f Y A PreSonus Louisiana 70809 USA 1 225 216 7887 D qunwipresanusicorn Parti 820 GEB0028 B
12. it an online technical support request at http support presonus com to receive a return authorization number and shipping information If you are located outside of the USA please contact the PreSonus distributor for your region for warranty repairs All inquiries must be accompanied by a description of the problem All authorized returns must be sent to the PreSonus repair facility postage prepaid insured and properly packaged PreSonus reserves the right to update any unit returned for repair PreSonus reserves the right to change or improve the design of the product at any time without prior notice This warranty does not cover claims for damage due to abuse neglect alteration or attempted repair by unauthorized personnel and is limited to failures arising during normal use that are due to defects in material or workmanship in the product Any implied warranties including implied warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this limited warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you In no event will PreSonus be liable for incidental consequential or other damages resulting from the breach of any express or implied warranty including among other things damage to property damage based on inconvenience or on loss of use of the product and to the extent permitted by law damages for persona
13. l injury Some states do not allow the exclusion of limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty only applies to products sold and used in the United States of America For warranty information in all other countries please refer to your local distributor PreSonus Audio Electronics Inc 18011 Grand Bay Ct Baton Rouge Louisiana 70809 USA 1 225 216 7887 www presonus com 18 Dinner is Served Added bonus PreSonus previously Top Secret recipe for Rice Dressing Ingredients e 1lb ground beef e 1 Ib chopped chicken liver 1 onion diced e 2 green peppers diced e 4 6 celery stalks diced e 2 garlic cloves minced e YC chopped fresh parsley e 3C chicken stock e 6C cooked rice e 1 Tbs oil e Salt and pepper to taste e Cayenne pepper to taste Cooking Instructions 1 Ina large pot heat oil on medium high and add meat salt and pepper to taste Stir until meat begins to brown 2 Lower heat and add all vegetables Cook until onions are transparent and celery is very tender Add stock as necessary to prevent burning 3 Stir in cooked rice Add remaining stock and simmer on low until ready to serve 2014 PreSonus Audio Electronics Inc All Rights Reserved Active Integration AudioBox DigiMax FireStudio N
14. temperature voice coil and damped rubber surround Frequency response 20 200 Hz Variable lowpass filter control 50 130 Hz 80 Hz highpass filter with defeat switch for satellite connections Sub HPF bypass with footswitch control Footswitch with cable included Front ported cabinet Metal mesh grille to protect driver 1 3 Whatis in the box In addition to this manual your Temblor T10 package contains the following 1 PreSonus Temblor T10 powered subwoofer 1 IEC power cable 1 Footswitch with cable 2 Hookup Temblor T10 2 1 Rear Panel Connections and Controls Owner s Manual 2 Hookup 2 1 Rear Panel Connections and Controls 2 1 1 Inputs Line level Inputs The Temblor T10 provides a choice of XLR three input pairs two sets of balanced inputs XLR and Ya TRS and one pair of RCA unbalanced inputs When both of the balanced connections are in use the TRS inputs will take precedence over the XLR inputs The RCA inputs will sum into either balanced connection dis 0 Two inputs are provided in order to accept a stereo RIGHT LEFT RIGHT LEFT signal from the output of your audio source Both channels should be connected as they will be summed together before passing through the onboard lowpass ADAC filter so you do not have to connect your audio source to pe goni a crossover 23 1 3 2 3 E Sleeve Ring Tip XLR TRS Ground H E Power User Tip If your a
15. tion for any 2 1 system The included latching footswitch lets you bypass the sub altogether making comparing your mix with or without sub frequencies quick and easy You can even cascade two Temblor T10s together for more and smoother bass We encourage you to contact us at 1 225 216 7887 9 a m to 5 p m Central Time with questions or comments regarding your PreSonus Temblor T10 PreSonus Audio Electronics is committed to constant product improvement and we value your suggestions highly We believe the best way to achieve our goal of constant product improvement is by listening to the real experts our valued customers We appreciate the support you have shown us through the purchase of this product and are confident that you will enjoy your Temblor T10 1 Overview Temblor T10 1 2 Summary of Temblor T10 Features Owner s Manual ABOUT THIS MANUAL We suggest that you use this manual to familiarize yourself with the features applications and correct connection procedures for your Temblor T10 before connecting it to the rest of your studio gear This will help you avoid problems during installation and setup In addition to all the basic info you ll need to connect and operate your Temblor T10 this manual also provides several tutorials that cover subwoofer placement connections and calibration 1 2 Summary of Temblor T10 Features Active subwoofer with 250 watt Class AB amplifier 10 inch glass composite woofer with high
16. tputs You should not hear anything yet 4h Tone Generator ITI rar MU Frequency Length Phase Sten Target Freq y Level 11 3 Tutorials 2 2 Hookup Diagrams None 2Trackin L R Temblor T10 Owner s Manual Power User Tip Some DAW applications including PreSonus Studio One offer a tone generator for this purpose If you re mixing in a DAW application use the built in tone generator or load a sample audio file or plug in After all your DAW is the beginning of your mixing environment s signal path Pan the pink noise so it only plays in the left speaker hard left Begin turning up the outputs of your primary audio source to their unity gain setting Unity gain is the level or setting at which the signal level is neither boosted nor attenuated and it is usually marked by a U on the audio device s level fader or knob In many digital interfaces and other digital devices the device s maximum level is also its unity gain setting Please consult your audio device s user manual or the manufacturer s Web site for more information on its levels and adjustments 6 Begin slowly increasing the input sensitivity volume of your left studio monitor until the acoustic level of the pink noise reaches 85 dB SPL on your SPL meter when measured at your mix position 12 3 Tutorials 2 2 Hookup Diagrams None 2Trackin L R 7 8 Temblor T10 Owner s
17. udio source provides balanced XLR or 4 TRS tip ring sleeve outputs use the corresponding balanced Temblor inputs Balanced connections are resistant to induced noise from radio frequency or electromagnetic interference RFI or EMI If the audio source has unbalanced 14 TS tip sleeve outputs use 14 to RCA adapters or adapter cables Always use the shortest cables possible to minimize the risk of induced RFI or EMI noise Input Gain Sets the level of the input signal before it is INPUT GAIN amplified 30dB 6dB 2 Hookup Temblor T10 2 1 Rear Panel Connections and Controls Owner s Manual 2 1 2 Outputs RIGHT LEFT HPF Off On round nm 1 3 1 2 3 Outputs The Temblor T10 provides two pairs g XLR D of balanced outputs XLR and 4 TRS The full range signal connected to the stereo inputs NH ontheT10 is passed through to these outputs Use these outputs to connect your main left _ and right studio monitors If the High Pass Filter switch is engaged frequencies below 80 Hz are Y not sent from these outputs SUB OUT SUB Bypass footswitch XLR O_O 2 o 3 OUTPUTS SUB OUT 2 1 3 Power a POWER AC SELECT Sub Out This balanced XLR output sends the low frequency signal from the lowpass filter to a second Temblor T10 When connecting a second T10 to
Download Pdf Manuals
Related Search