Model 1020 Standalone Enclosure User Manual
Contents
1. Web Site www canoga com Email fiber canoga com Copyright 2003 2005 Canoga Perkins Corporation All Rights Reserved EdgeAccess Universal Chassis System Model 1020 Users Manual Model Number 1020 UM Product Number 6913070 Rev C 09 2005 MM 2 EdgeAccess Model 1020 Model 1020 Standalone Enclosure User Manual The Model 1020 standalone enclosure shown in Figure 1 supports one 2U sized module that is managed through either SNMP or Sideband Management Control SBMC A Figure 1 Model 1020 Standalone Enclosure The front provides three switches three LEDs two connectors and a slot for a managed module The back includes an AC power cord socket The AC power supply provides 5 VDC to the module Switch Setting Selects MDM TRM for EIA 232 port MDM DTE terminal for SLIP TRM DCE terminal for VT100 F1 NRM F2 typically for Loopback for the module F1 Local loopback typically Note Set to NRM except to isolate a fault NRM Normal operation F2 Remote loopback typically HDX FDX for 10BASE T port HDX Half duplex FDX Full duplex Note If the link partner is set to auto negotiation the link uses 10M and follows the HDX FDX switch setting for this port otherwise set this switch to match the other switch on the link LED State Definition PWR Off No power Green Power is on Tx for 10BASE T port Off No transmission Green blinking Transmission activity LNK Rx for 10BASE T port Off No link Green Link is estab2. and click OK At the COM Properties dialog on the Port Settings tab check for these selections e Bits per second 19200 bps e Data bits 8 e Parity None e Stop bits 1 e Flow control None Click OK HyperTerminal connects to the system and the VT100 terminal emulation starts To use the module and access its management functions in the 1020 enclosure see the User Manual for the module EdgeAccess Model 1020 Specifications Dimensions 10 0 L x 6 25 W x 1 625 H 254 mm x 159 mm x 43 mm Weight 3 0 lbs 1 4 kg Power 10 W maximum 100 to 240 VAC 50 to 60 Hz autoranging Operating Environment 0 to 50 C Up to 90 Non condensing Regulatory Compliance ETL cETL UL 60950 CAN CSA C22 2 No 60950 EN IEC 60950 EN 60825 1 2 CDRH CFR21 FCC Part 15B IC 003 VCCI Class A C Tick AS NZS 3548 EN 55022 Class A EN 61000 3 2 EN 61000 3 3 EN 55024 R amp TTE Directive EN 300 386 CE Mark EdgeAccess Model 1020 EdgeAccess Model 1020 Limited Lifetime Warranty Effective July 1 2005 and After Canoga Perkins warrants that at the time of sale and for its lifetime with certain exceptions noted below every Canoga Perkins labeled product purchased will be free from defects in material and workmanship for its lifetime if properly installed and used in conformity to Canoga Perkins published specifications This warranty covers the original user only and is not transferable For the purposes of this Warr
3. CANOGA PERKINS Model 1020 Standalone Enclosure User Manual NOTICE This device contains static sensitive components It should be handled only with proper Electrostatic Discharge ESD grounding procedures NOTE Cet quipement contient des composants sensibles aux d charges lectro statiques Il doit absolument tre manipul en respectant les r gles de mise la terre afin de pr venir de telles d charges NOTICE Canoga Perkins has prepared this users manual for use by customers and Canoga Perkins personnel as a guide for the proper installation operation and or maintenance of Canoga Perkins equipment The drawings specifications and information contained in this document are the property of Canoga Perkins and any unauthorized use or disclosure of such drawings specifications and information is prohibited Canoga Perkins reserves the right to change or update the contents of this manual and to change the specifications of its products at any time without prior notification Every effort has been made to keep the information in this document current and accurate as of the date of publication or revision However no guarantee is given or implied that the document is error free or that is accurate with regard to any specification Canoga Perkins Corporation 20600 Prairie Street Chatsworth California 91311 6008 Business Phone 818 718 6300 Monday Friday 7 a m 5 p m Pacific Time FAX 818 718 6312 24 hrs
4. ETHER IN CONTRACT IN TORT UNDER ANY WARRANTY IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE AMOUNT OF THE PURCHASE PRICE PAID BY THE CUSTOMER AND UNDER NO CIRCUMSTANCES SHALL CANOGA PERKINS BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES THE PRICE STATED FOR THE EQUIPMENT IS A CONSIDERATION IN LIMITING CANOGA PERKINS LIABILITY NO ACTION REGARDLESS OF FORM ARISING OUT OF THE TRANSACTIONS OF THIS AGREEMENT MAY BE BROUGHT BY CUSTOMER MORE THAN ONE YEAR AFTER THE CAUSE OF THE ACTION HAS ACCRUED CANOGA PERKINS MAXIMUM LIABILITY SHALL NOT EXCEED AND CUSTOMER S REMEDY IS LIMITED TO EITHER i REPAIR OR REPLACEMENT OF THE DEFECTIVE PART OF PRODUCT OR AT CANOGA PERKINS OPTION 11 RETURN OF THE PRODUCT AND REFUND OF THE PURCHASE PRICE AND SUCH REMEDY SHALL BE CUSTOMER S ENTIRE AND EXCLUSIVE REMEDY AUTHORIZED RESELLERS ARE NOT AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON CANOGA PERKINS BEHALF Return Policy Customer must obtain an RMA Return Material Authorization number from the Canoga Perkins Customer Service Department before returning a product for service or repair Canoga Perkins technical support department can be reached through any of the following means Telephone 818 718 6300 Fax 818 718 6312 E Mail fiber canoga com If the warranty for a power supply fan optics consumable or software has expired customer must provide the Canoga Perkins Customer Service Representative with a Purchase Order to auth
5. anty lifetime is defined as the serviceable life of the product a minimum of 5 years or any longer period during which replacement spare parts are available Subject to the conditions and limitations set forth below Canoga Perkins will at its option either repair or replace any part of its product s that prove defective by reason of improper workmanship or materials The warranty period for power supplies fans and optics is five 5 years Consumables such as filters are covered for one year Software is warranted for 90 days Hardened Media Converter HS products are covered for three 3 years This warranty does not cover any damage to products that have been subjected to lightning or other Acts of Nature misuse neglect accident damage improper installation or maintenance including over voltage failures caused by use outside of the product s specified rating normal wear and tear of mechanical components or alteration or repair by anyone other than Canoga Perkins or its authorized representative Ifthe user is unsure about the proper means of installing or using the equipment contact Canoga Perkins free technical support services Customer must notify Canoga Perkins promptly in writing of any claim based on warranty Canoga Perkins is not liable for and does not cover under warranty any costs associated with servicing and or the installation of its products or for any inspection packing or labor costs in connection with return of good
6. lished at full duplex Amber Link is established at half duplex Blinking Data is received EdgeAccess Model 1020 3 Connector Manages EIA 232 Serial port for modem or terminal 10BASE T Halfor full duplex Ethernet supports only modules that include SNMP such as 2x46 or L3x1 Installing and Using the 1020 Enclosure To use the 1020 enclosure 1 Place it on a secure surface with room for air flow and within 10 ft 3 m of the AC power source Insert a managed module in the guide rails and press it firmly into the backplane then secure the thumbscrew finger tight Plug the power cord into the rear of the 1020 enclosure then plug it into the AC power source this turns on the power To turn off the power unplug the power cord To set any switches on the module install the module in the 1020 enclosure connect all cables and access the module see the User Manual for the module Use HyperTerminal for your first VT100 session These steps briefly describe how to set up your PC for a terminal connection For details on using Windows see your Windows documentation 1 Za Turn on your PC When the Windows desktop appears click Start then highlight Programs Accessories the HyperTerminal Folder and then click HyperTerminal At the Connection Description dialog select an icon enter a name for the connection to the system and click OK At the Connect To dialog pull down the Connect using menu select the COM port
7. orize the repair Send the defective product postage and insurance prepaid to the address provided to you by Canoga Perkins technical support representative Failure to properly protect the product during shipping may void this warranty The return authorization number must be written on the outside of the carton to ensure its acceptance The customer must pay for the non compliant product s return transportation costs to Canoga Perkins for evaluation of said product s for repair or replacement Canoga Perkins will pay for the shipping of the repaired or replaced in warranty product s back to the customer any and all customs charges tariffs or and taxes are the customer s responsibility Canoga Perkins reserves the right to charge for all testing and shipping incurred if after testing a return is classified as No Problem Found CANOGA PERKINS 8 EdgeAccess Model 1020
8. s In the event Canoga Perkins breaches its obligation of warranty customer s sole and exclusive remedy is limited to replacement repair or credit of the purchase price at Canoga Perkins option Under no circumstance will Canoga Perkins be liable for consequential or incidental damages or loss of profits Warranty Registration To establish original ownership and to record purchase date please complete the warranty on line form on our product registration page URL www canoga com warranty Optional Service Programs Canoga Perkins offers several optional Service Programs Please call Canoga Perkins Sales Department 818 718 6300 or see our web site www canoga com for details CUSTOMER SERVICE DEPARTMENT REPAIR WARRANTY Repairs performed by the Canoga Perkins Customer Service Department will be free from defects in material and workmanship for a period of ninety 90 DAYS from the date the repaired product is shipped or until the expiration of the original factory warranty whichever is longer EdgeAccess Model 1020 7 Limitations Canoga Perkins may at its sole discretion modify its Limited Warranty at any time and from time to time Other than those expressly stated herein THERE ARE NO OTHER WARRANTIES OF ANY KIND EXPRESSED OR IMPLIED AND SPECIFICALLY EXCLUDED BUT NOT BY WAY OF LIMITATION ARE THE IMPLIED WARRANTIES FOR FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY IT IS UNDERSTOOD AND AGREED CANOGA PERKINS LIABILITY WH
Download Pdf Manuals
Related Search