Moxa VP-IR2 Series User`s Manual
Contents
1. E aii enced es ei esse rat edad dies crei cc es elusive rset evaieiaee sees ersten ENN 2 1 Synchronization ieieieieiioses A 2 2 1 Introduction The VP IR2 series IR illuminator is designed specifically to work with Moxa VPort series IP cameras It features high power efficiency and a long LED life cycle and is suitable for all types of industrial surveillance applications The VP IR2 can be easily mounted on a VPort camera housing Package Checklist e VP IR2 series IR illuminator e Nut and bolt for mounting the VP IR2 to a VPort camera housing e Power and I O cable NOTE Moxa s VP IR2 Series is shipped with the mounting bracket attached to the body When installing the VP IR2 use an appropriate screw to attach the VP IR2 mounting bracket to a wall or use the provided nut and bolt to attach the VP IR2 mounting bracket to an appropriate device or frame Ordering Information Model Name Description VP IR22080 Infrared LED illuminator 20 850 nm 12 VDC 60 to 100 m effective range VP IR26080 Infrared LED illuminator 60 850 nm 12 VDC 20 to 50 meter effective range NOTE Check the model name on the VP IR2 s side label to verify that you received the model you ordered NOTE This product must be installed in compliance with your local laws and regulations Moxa VP IR2 Series Introduction Physical Description A Protective Cover made with PMMA material B Main body C Mounting Bracket D Powe2. Moxa VP IR2 Series User s Manual Second Edition August 2014 www moxa com product MOXA 2014 Moxa Inc All rights reserved Moxa VP IR2 Series User s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice Trademarks O 2014 Moxa Inc All rights reserved The MOXA logo is a registered trademark of Moxa Inc All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa Moxa provides this document as is without warranty of any kind either expressed or implied including but not limited to its particular purpose Moxa reserves the right to make improvements and or changes to this manual or to the products and or the programs described in this manual at any time Information provided in this manual is intended to be accurate and reliable However Moxa assumes no responsibility for its use or for any infringements on the rights of third parties that may result from its use This product might include unintentional technical or typographical errors Changes are periodically made to the information herein to correct such errors and these changes are incorporated into new editions of the publication Technical Support Contact Informatio
3. e 1 2 Moxa VP IR2 Series Introduction c Attach the VP IR2 to the housing with the nut and bolt provided in the package ae 1 NOTE Be sure to install the VP IR2 onto the VP CI701 housing and VP CI800 bracket before you install it on the wall NOTE Follow the same process if you are installing the VP IR2 to another housing or camera 1 3 NOTE A Product Specifications VP IR2 Series Infrared Wavelength 850 nm Angle VP IR22080 20 VP IR26080 60 IR Effective Range VP IR22080 60 to 100 m VP IR26080 20 to 50 m Automatic IR On Off Controlled by built in photocell Operating Temperature 30 to 60 C 22 to 140 F IP Rating IP66 ICR Switching Volt free relay output Power Consumption 12 W Power Requirement 12 VDC You can mount multiple VP IR2 IR illuminators pointing in the same direction to increase the illuminated distance and area
4. n Moxa Americas Toll free 1 888 669 2872 Tel 1 714 528 6777 Fax 1 714 528 6778 Moxa Europe Tel 49 89 3 70 03 99 0 Fax 49 89 3 70 03 99 99 Moxa India Tel 91 80 4172 9088 Fax 91 80 4132 1045 www moxa com su ort Moxa China Shanghai office Toll free 800 820 5036 Tel 86 21 5258 9955 Fax 86 21 5258 5505 Moxa Asia Pacific Tel 886 2 8919 1230 Fax 886 2 8919 1231 Before Getting Started Before using your VP IR2 read the following information O The VP IR2 is designed for the following applications 1 For use with Moxa VPort series IP cameras to enhance night view images 2 For use independently as an illuminator O To prevent damage or problems caused by improper use read this user s manual before operating the device and peripherals O If you experience a system error and the system cannot be recovered please contact your local distributor 1 A Table of Contents IntroduUcti n siisisisdsusinunauindndudndnununnadn dunnuna nananana naai aaau a KAWANA USAn Daun EN SENEN RaDa 1 1 Pack Ad 1 1 Ordering Information A A a 1 1 Physical Descriptio Merman as cannes neat oss era deubiventsanavinds evexeusued ama rara vrs ac SAIPAN n AN ana Soni Dina IEEE EEE TATSI A 1 2 DIMENSIONS Unit EA tia rea a A AA a ai 1 2 UY Te eee eee reer eee er ere rer eerereerer rere reererrerer rere errr rere errr eerre errr eeereer eer rere errr re errr eeeere tree eer etree terete 2 1 Installatie aE EE E
5. r amp Signal I O Dimensions unit mm 1 2 Usage In this chapter we describe how to install and synchronize the VP IR2 Installation The VP IR2 IR illuminator is usually used together with a Moxa CCTV camera The VP IR2 can be installed in the following ways 1 Mounted to a wall use an appropriate screw The VP IR2 comes with a mounting bracket already attached that can be mounted to a wall Use an appropriate screw to mount the unit to a wall and then connect the power and I O cable to the camera that the VP IR2 will be used with 2 Mounted to a pole use an appropriate pole mount kit To mount the VP IR2 to a pole choose a pole mount adapter that is suitable for the size of the pole and then mount the VP IR2 to the adapter 3 Mounted to a VP camera housing and VPort camera Use the nut and bolt included in the package to attach the VP IR2 to a VP camera housing The following example illustrates how to install the VP IR2 to a VP CI701 housing and VP CI800 bracket a Install the VPort camera in the VP CI701 camera housing b Pull the VP IR2 s power and I O cable through the VP CI800 bracket The end of the cable with loose electric wires should be pulled out from the top of the bracket as illustrated in the following photograph I i o c Pull the wire end of the cable into VP CI701 housing through the waterproof connector at the bottom of the VP CI701 s housing Completel
6. y tighten the waterproof connector after the cable is pulled through d Connect the wires to the camera as indicated below Black to camera power connector V Red to camera power connector V Blue to camera DI ground Yellow to camera DI IN Brown Orange Not used Moxa VP IR2 Series Introduction Synchronization To synchronize the VP IR2 s auto on off function with the camera s Day Night switch connect the VP IR2 s relay output to the VPort camera s input Take the following steps to complete the configuration 1 Open the Image Tuning page from the camera s web browser interface and then configure the camera s Day Night switch to D I Control Image Tuning V UDP 2006 05 31 14 21 1 4 Environment Outdoor Indoor Image Adjustments Saturation 0 v Contrast 0 Sharpness 0 v AGC 16X BLC Middle AWB ATW Appearance Normal hd Digital Noise Reduction O Enable Day Night Day Night Tngger ralay output when day night mode sunt Relay status is Norma Gose when day mode Relay status is Norma Oper when night made Auto Exposure Shutter Auto Level 0 WDR WOR Level 8 Auto IRIS Enable 2 Connect the VP IR2 s D O to the camera s D I as described below Blue wire to camera DI ground Yellow wire to camera DI IN a Close the VP CI701 s housing and mount the VP CI800 s bracket on the housing b Install the housing and bracket to the desired surfac
Download Pdf Manuals
Related Search