Home

User Guide

Contents

1. Power connector H Mouse connector Serial connector El Parallel connector H Ethernet connector El Audio line in connector PCI slots EJ AGP slot some models E Audio line out connector Microphone connector USB connectors VGA monitor connector Serial connector USB connectors Keyboard connector Note Some connectors on the rear of the computer are color coded to help you to determine where to connect the cables on your computer Chapter 3 Types 8305 8306 8309 and 8313 37 Connector Mouse connector Serial connector Parallel connector Ethernet connector Audio line in connector Audio line out connector Microphone connector USB connectors Keyboard connector Description Used to attach a mouse trackball or other pointing device that uses a standard mouse connector Used to attach an external modem serial printer or other devices that use a 9 pin serial connector Used to attach a parallel printer parallel scanner or other devices that use a 25 pin parallel connector Used to attach an Ethernet cable for a local area network LAN Note To operate the computer within FCC Class B limits use a Category 5 Ethernet cable Used to receive audio signals from an external audio device such as a stereo system When you attach
2. m Od i m Microprocessor E Battery H DIMM connector 1 Clear CMOS Recovery jumper DIMM connector 2 SCSI LED connector El Power connector PCI slots E Diskette drive connector Front panel audio connector El Primary IDE connector CD ROM audio connector Front panel connector AGP slot some models H Secondary IDE connector Serial connector Installing memory Your computer has two connectors for installing dual inline memory modules DIMMs that provide up to a maximum of 2 0 GB of system memory When installing DIMMs the following rules apply Fill each system memory connector sequentially starting at DIMM connector 1 Use 2 5 V 184 pin 266 MHz double data rate synchronous dynamic random access memory DDR SDRAM Use 128 MB 256 MB 512 MB or 1 0 GB when available DIMMs in any combination e DIMMs are 38 1 mm 1 5 inches in height Note Only DDR SDRAM DIMMs can be used To install a DIMM 1 Remove the cover See Removing the cover on page 17 Chapter 2 Types 8303 8304 and 8312 19 2 To locate the DIMM connectors See Identifying parts on the system board onl 3 Open the retaining clips ha 4 Make sure the notches in the DIMM align with the tabs on the connector Push or insert the DIMM straight down into the connector
3. VBT VCI Beep Tone Timer Identify Compression Method VLS Voice line select VRA Ringback goes away timer VRN Ringback never came timer VRX Voice Receive Mode VSDB Silence deletion tuner VSK Buffer skid setting VSP Silence detection period VSR Sampling rate selection VSS Silence deletion tuner VTD DTMF tone reporting capability VTM Enable timing mark placement VTS Generate tone signals VTX Voice transmit mode 88 User Guide r Attention Switzerland User If your Swisscom phone line does not have Taxsignal switched OFF modem function may be impaired The impairment may be resolved by a filter with the following specifications Telekom PTT SCR BE Taximpulssperrfilter 12kHz PTT Art 444 112 7 Bakom 93 0291 Z N Appendix B Manual modem commands 89 90 User Guide Appendix C System address maps The following charts represent how the hard disk stores different types of information Address ranges and byte sizes are approximate System memory map The first 640 KB of system board RAM is mapped starting at address hex 00000000 A 256 byte area and a 1 KB area of this RAM are reserved for BIOS data Memory can be mapped differently if POST detects an error Table 1 System memory map Address range Address range Size Description de
4. Chapter 3 Types 8305 8306 8309 and 8313 51 52 User Guide Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 This chapter provides an introduction to the features and options that are available for your computer You can expand the capabilities of your computer by adding memory adapters or drives When installing an option use these instructions along with the instructions that come with the option m Important Before you install or remove any option read Safety Information on page v These precautions and guidelines will help you work safely Features This section provides an overview of the computer features and preinstalled software Microprocessor varies by model type Intel Pentium 4 processor with 256 KB or 512 KB of internal L2 cache memory and Intel NetBurst micro architecture Memory Support for two dual inline memory modules DIMMs e 512 KB flash memory for system programs Internal drives e 3 5 inch 1 44 MB diskette drive e Internal hard disk drive e EIDE CD drive or DVD drive Video subsystem e Intel Extreme graphics Copyright IBM Corp 2002 53 54 User Guide Accelerated graphics port AGP video adapter slot on the system board some models Audio subsystem Integrated SoundMAX 3 audio Connectivity 10 100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN feature Soft modem V 90 V 44 some models S
5. Soft modem V 90 V 44 some models System management features Remote Program Load RPL and Dynamic Host Configuration Protocol DHCP e Wake on LAN Wake on Ring in the IBM Setup Utility program this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem Remote Administration Automatic power on startup System Management SM BIOS and SM software Ability to store POST hardware test results Input output features e 25 pin Extended Capabilities Port ECP Extended Parallel Port EPP e Two 9 pin serial connectors Six 4 pin USB connectors PS 2 mouse connector e PS 2 keyboard connector e Ethernet connector e VGA monitor connector Three audio connectors line in line out and microphone Front connectors for headphone microphone IEEE 1394 and S PDIF some models Expansion e Three drive bays e Three 32 bit peripheral component interconnect PCI adapter slots supports low profile adapters only One accelerated graphics port AGP expansion slot supports low profile adapters only Power 160 W power supply with manual voltage selection switch Automatic 50 60 Hz input frequency switching Advanced Power Management support Advanced Configuration and Power Interface ACPI support Security features User and administrator passwords Support for the addition of a rope clip and lockable cable Support
6. i m Microprocessor E Battery H DIMM connector 1 Clear CMOS Recovery jumper DIMM connector 2 SCSI LED connector El Power connector PCI slots E Diskette drive connector Front panel audio connector g Primary IDE connector CD ROM audio connector Front panel connector AGP slot some models E Secondary IDE connector Serial connector Installing memory Your computer has two connectors for installing dual inline memory modules DIMMs that provide up to a maximum of 2 0 GB of system memory When installing DIMMs the following rules apply Fill each system memory connector sequentially starting at DIMM connector 1 Use 2 5 V 184 pin 266 MHz double data rate synchronous dynamic random access memory DDR SDRAM Use 128 MB 256 MB 512 MB or 1 0 GB when available DIMMs in any combination e DIMMs are 38 1 mm 1 5 inches in height Note Only DDR SDRAM DIMMs can be used To install a DIMM 1 Remove the cover See Removing the cover on page 39 Chapter 3 Types 8305 8306 8309 and 8313 41 2 You might have to remove an adapter to gain access to the DIMM slots See Installing adapters on page 42 3 To locate the DIMM connectors See Identifying parts on the system board on page 40 4 Open the retaining clips lt 5 Make sure the notches in the DIMM align with the tabs on the connector Push or insert the DIMM straight down into the connector until the retaining clips cl
7. Parameter e specifies the codec type 0 Law and 1 A Law Parameter f specifies robbed bit signaling detection 0 detection disabled 1 detection enabled MNP V 42 V 42bis V 44 commands Command Function C_ CO Disable MNP Class 5 and V 42bis data compression C1 Enable MNP Class 5 data compression only C2 Enable V 42bis data compression only C3 Enable MNP Class 5 and V 42bis data compression amp Q_ amp Q0 Direct data link only same as N1 amp Q5 V 42 data link with fallback options amp Q6 Normal data link only same as NO DS44 0 0 Disable V 44 DS44 3 0 Enable V 44 DS44 Current values DS44 List of support values 86 User Guide Fax Class 1 commands FAE n Data Fax Auto Answer FCLASS n Service Class FRH n Receive data with HDLC framing FRM n Receive data FRS n Receive silence FTH n Transmit data with HDLC framing FTM n Transmit data FTS n Stop transmission and wait Fax Class 2 commands FCLASS n FAA n Services class Adaptive answer FAXERR FBOR Fax error value Phase C data bit order FBUF Buffer size read only FCFR Indicate confirmation to receive FCLASS Service class FCON Facsimile connection response FCIG Set the polled station identification FCIG Report the polled stat
8. 10 to 35 C 50 to 95 F System off 10 to 43 C 50 to 110 F Maximum altitude 2134 m 7000 ft Note The maximum altitude 2134 m 7000 ft is the maximum altitude at which the specified air temperatures apply At higher altitudes the maximum air temperatures are lower than those specified Humidity System on 8 to 80 System off 8 to 80 Electrical input Input voltage Low range Minimum 90 V ac Maximum 137 V ac Input frequency range 57 63 Hz Voltage switch setting 115 V ac High range Minimum 180 V ac Maximum 265 V ac Input frequency range 47 53 Hz Voltage switch setting 230 V ac Input kilovolt amperes kVA approximate Minimum configuration as shipped 0 08 kVA Maximum configuration 0 3 kVA Note Power consumption and heat output vary depending on the number and type of optional features installed and the power management optional features in use Heat output approximate in British thermal units Btu per hour Minimum configuration 257 Btu hr 75 watts Maximum configuration 890 Btu hr 260 watts Airflow Approximately 0 56 cubic meters per minute 20 cubic feet per minute maximum Acoustical noise emission values Average sound pressure levels At operator position Idle 33 dBA Operating 36 dBA At bystander position 1 meter 3 3 ft Idle 30 dBA Operating 33 dBA Declared upper limit sound power levels Idle 4 4 bels Operating 4 7 bels Note These levels were
9. 34 dBA Declared upper limit sound power levels Idle 4 4 bels Operating 4 7 bels Note These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute ANSI 12 10 and ISO 7779 and are reported in accordance with ISO 9296 Actual sound pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources The declared sound power levels indicate an upper limit below which a large number of computers will operate Note See the Quick Reference for the classification of your computer 4 User Guide Available options The following are some available options External options Parallel port devices such as printers and external drives Serial port devices such as external modems and digital cameras Audio devices such as external speakers for the sound system USB devices such as printers joysticks and scanners Monitors Internal drives such as CD ROM drive some models Hard disk drive For the latest information about available options see the following World Wide Web pages http www ibm com pc us options http www ibm com pc support You can also obtain information by calling the following telephone numbers Within the United States call 1 800 IBM 2YOU 1 800 426 2968 your IBM reseller or IBM marketing representative
10. Maximum configuration 10 2 kg 22 5 Ib Environment Air temperature System on 10 to 35 C 50 to 95 F System off 10 to 43 C 50 to 110 F Maximum altitude 2134 m 7000 ft Note The maximum altitude 2134 m 7000 ft is the maximum altitude at which the specified air temperatures apply At higher altitudes the maximum air temperatures are lower than those specified Humidity System on 8 to 80 System off 8 to 80 Electrical input Input voltage Low range Minimum 90 V ac Maximum 137 V ac Input frequency range 57 63 Hz Voltage switch setting 115 V ac High range Minimum 180 V ac Maximum 265 V ac Input frequency range 47 53 Hz Voltage switch setting 230 V ac Input kilovolt amperes kVA approximate Minimum configuration as shipped 0 08 kVA Maximum configuration 0 3 kVA Note Power consumption and heat output vary depending on the number and type of optional features installed and the power management optional features in use Heat output approximate in British thermal units Btu per hour Minimum configuration 257 Btu hr 75 watts Maximum configuration 890 Btu hr 260 watts Airflow Approximately 0 76 cubic meters per minute 26 cubic feet per minute maximum Acoustical noise emission values Average sound pressure levels At operator position Idle 30 dBA Operating 34 dBA At bystander position 1 meter 3 3 ft Idle 29 dBA Operating 33 dBA Declared upper limit
11. See Chapter 5 Using the IBM Setup Utility program on page 77 Erasing a lost or forgotten password clearing CMOS This section applies to lost or forgotten passwords For more information about lost or forgotten passwords see Access IBM on your desktop To erase a forgotten password 1 2 3 Turn off the computer and all attached devices Remove the cover See Removing the cover on page 61 Locate the Clear CMOS Recovery jumper on the system board See Identifying parts on the system board on page 63 If necessary see Installing adapters on page 65 to remove any adapters that impede access to the Clear CMOS Recovery jumper Move the jumper from the standard position pins 1 and 2 to the maintenance or configure position pins 2 and 3 Replace the cover and connect the power cord See Replacing the cover and connecting the cables Restart the computer leave it on for approximately 10 seconds Turn off the computer by holding the power switch for approximately 5 seconds The computer will turn off Repeat steps 2 through 4 on page 74 Move the jumper back to the standard pins 1 and 2 Replace the cover and connect the power cord See Replacing the cover and connecting the cables Replacing the cover and connecting the cables 74 User Guide After working with options you need to install any removed parts replace the cover and reconnect any cables includin
12. and 8313 49 Install the new battery Remove the old battery i So m Replace any adapters that were removed to gain access to the battery See Installing adapters on page 42 for instructions for replacing adapters Replace the cover and plug in the power cord See Replacing the cover and connecting the cables on page 51 Note When the computer is turned on for the first time after battery replacement an error message might be displayed This is normal after replacing the battery Turn on the computer and all attached devices Use the IBM Setup Utility program to set the date and time and an passwords See Chapter 5 Using the IBM Setup Utilit Erasing a lost or forgotten password clearing CMOS This section applies to lost or forgotten passwords For more information about lost or forgotten passwords see Access IBM on your desktop To erase a forgotten password 1 2 3 50 User Guide Turn off the computer and all attached devices Remove the cover See Removing the cover on page 39 Locate the Clear CMOS Recovery jumper on the system board See Identifying parts on the system board on page 40 If necessary see Installing adapters on page 42 to remove any adapters that impede access to the Clear CMOS Recovery jumper Move the jumper from the standard position pins 1 and 2 to
13. de CD ROM DVD ROM peut entra ner un risque d exposition au rayon laser Pour toute intervention faites appel du personnel qualifi Certaines unit s de CD ROM DVD ROM peuvent contenir une diode a laser de classe 3A ou 3B Tenez compte de la consigne qui suit DANGER Rayonnement laser lorsque le carter est ouvert Evitez toute exposition directe des yeux au rayon laser vitez de regarder fixement le faisceau ou de l observer l aide d instruments optiques Overview Thank you for selecting an IBM computer Your computer incorporates many of the latest advances in computer technology and can be upgraded as your needs change This publication supports several computer models Information in this section will help you identify your computer and help you find the chapter that contains information specific to your computer Adding hardware options to your computer is an easy way to increase its capabilities Instructions for installing external and internal options are included in this publication When adding an option use these instructions along with the instructions that come along with the option Information resources The Quick Reference that comes with your computer provides information for installing your computer and starting the operating system It also includes basic troubleshooting information software recovery procedures help and service information and warranty information Access IBM o
14. package and your body When possible remove the option and install it directly in the computer without setting the option down When this is not possible place the static protective package that the option came in on a smooth level surface and place the option on it Do not place the option on the computer cover or other metal surface Installing external options This section shows the various external connectors on your computer to which you can attach external options such as external speakers a printer or a scanner For some external options you must install additional software in addition to making the physical connection When adding an external option use the information in this section to identify the required connector and then use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer wr 60 oO dd USB connector A USB connector 36 User Guide Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer fe 2 1 0209080 fe 90 6 o o o o o O re o Q O o a a O fe fo fe a
15. sound power levels Idle 4 4 bels Operating 4 7 bels Note These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute ANSI 12 10 and ISO 7779 and are reported in accordance with ISO 9296 Actual sound pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources The declared sound power levels indicate an upper limit below which a large number of computers will operate Note See the Quick Reference for the classification of your computer 56 User Guide Available options The following are some available options e External options Parallel port devices such as printers and external drives Serial port devices such as external modems and digital cameras Audio devices such as external speakers for the sound system USB devices such as printers joysticks and scanners Security device such as a rope clip Monitors IEEE 1394 devices requires an IEEE 1394 adapter Internal options System memory called dual inline memory modules DIMMs Peripheral component interconnect PCI adapters Accelerated graphics port AGP adapters Internal drives such as CD drive and DVD drive Hard disk drive Diskette drives and other removable media drives For the latest information about available options see the following Wo
16. write request register 00 02 000A Channels 0 3 write single mas register bits 00 02 000B Channels 0 3 mode register write 00 07 000C Channels 0 3 clear byte pointer write N A 000D Channels 0 3 master clear write temp 00 07 read 000E Channels 0 3 clear mask register write 00 03 000F Channels 0 3 write all mask register bits 00 03 0081 Channel 2 page table address register 00 07 0082 Channel 3 page table address register 00 07 Appendix C System address maps 93 94 User Guide Table 3 DMA I O address map continued Address hex Description Bits Byte pointer 0083 Channel 1 page table address register 00 07 0087 Channel 0 page table address register 00 07 0089 Channel 6 page table address register 00 07 008A Channel 7 page table address register 00 07 008B Channel 5 page table address register 00 07 008F Channel 4 page table address refresh 00 07 register 00C0 Channel 4 memory address register 00 15 Yes 00C2 Channel 4 transfer count register 00 15 Yes 00C4 Channel 5 memory address register 00 15 Yes 00C6 Channel 5 transfer count register 00 15 Yes 00C8 Channel 6 memory address register 00 15 Yes 00CA Channel 6 transfer count register 00 15 Yes 00CC Channel 7 memory address register 00 15 Yes 00CE Channel 7 transfer count register 00 15 Yes 00D0 Channels 4 7 read status write
17. 5 Thread the cable through the rope clip and around an object that is not a part of or permanently secured to the building structure or foundation and from which it cannot be removed then fasten the cable ends together with a lock r What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 51 Changing the battery Your computer has a special type of memory that maintains the date time and settings for built in features such as parallel port assignments configuration A battery keeps this information active when you turn off the computer The battery normally requires no charging or maintenance throughout its life however no battery lasts forever If the battery fails the date time and configuration information including passwords are lost An error message is displayed when you turn on the computer Refer to Lithium battery notice on page vil for information about replacing and disposing of the battery To change the battery 1 Turn off the computer and all attached devices Remove the cover See Removing the cover on page 39 Locate the battery See Identifying parts on the system board on page 40 If necessary remove any adapters that impede access to the battery See Installing adapters on page 42 for more information PON Chapter 3 Types 8305 8306 8309
18. 9GHz 2 0GHz 2 26GHz Normal Power consumption W 59 W 58 W 61 W 64 W Maximum power consumption W VA 172 W 176 W 1152 W 160 W 219 VA 233 VA 194 VA 203 VA Wattage when suspend W 3 1 W 3 1 W 3 1 W 3 1 W Wattage when power off W 2 7 W 2 7 W 2 7 W 2 7 W Energy consumption efficiency class Q Q Q Q Class Q Criteria 0 12 0 12 0 12 0 12 CTP in MTOPS 4800 5067 5333 6027 Energy consumption efficiency value 0 00065 0 00061 0 00058 0 00051 Appendix E Notices 99 100 User Guide Types 8310 and 8311 value 1 8GHz 1 9GHz 2 0GHz 2 26GHz 2 4GHz Normal Power consumption W 59 W 61 W 58 W 61 W 64 W Maximum power consumption W 180 W 184 W 160 W 169 W 174 W VA 232 VA 236 VA 204 VA 213 VA 220 VA Wattage when suspend W 3 1 W 13 1 W 3 1 W 13 1 W 3 1 W Wattage when power off W 2 7 W 12 7 W 2 7 W 12 7 W 2 7 W Energy consumption efficiency Q Q Q Q Q class Class Q Criteria 0 12 0 12 0 12 0 12 0 12 CTP in MTOPS 4800 5067 5333 6027 6400 Energy consumption efficiency 0 00065 0 00061 0 00058 0 00051 0 00048 Index A adapters accelerated graphics port AGP 13 35 57 installing Types 8303 8304 and 8312 20 Types 8305 8306 8309 and 8313 42 Types 8307 8308 8310 8311 8314 and 8315 65 peripheral component interconnect PCI 13 35 57 slots 20 42 65 address map DMA input
19. CMOS Recovery jumper Move the jumper from the standard position pins 1 and 2 to the maintenance or configure position pins 2 and 3 Replace the cover and connect the power cord See Replacing the cover and connecting the cables Restart the computer leave it on for approximately 10 seconds Turn off the computer by holding the power switch for approximately 5 seconds The computer will turn off Repeat steps 2 through 4 on page 8 Move the jumper back to the standard pins 1 and 2 Replace the cover and connect the power cord See Replacing the cover and connecting the cables Replacing the cover and connecting the cables 28 User Guide After working with options you need to install any removed parts replace the cover and reconnect cables including telephone lines and power cords Also depending on the option that is installed you might need to confirm the updated information in the IBM Setup Utility program To replace the cover and connect cables to your computer 1 2 Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer Clear any cables that might impede the replacement of the cover 3 Position the cover over the chassis and pivot it down over the computer until it snaps into place 4 Reconnect the external cables and power cords to the computer See Installing external options on page 14 5 To
20. I O control Serial and parallel port I O control Security profile by device IBM preinstalled software Your computer might come with preinstalled software If it does an operating system device drivers to support built in features and other support programs are included Operating systems preinstalled varies by model type Note Not all countries or regions will have these operating systems e Microsoft Windows XP Home e Microsoft Windows XP Professional e Microsoft Windows 2000 Professional Operating systems tested for compatibility e Microsoft Windows NT Workstation Version 4 0 e Microsoft Windows 98 Second Edition e 09 2 3 The operating systems listed here are being tested for compatibility at the time this publication goes to press Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet Corrections and additions to this list are subject to change To determine if an operating system has been tested for compatibility check the Web site of the operating system vendor Chapter 3 Types 8305 8306 8309 and 8313 33 Specifications This section lists the physical specifications for your computer Dimensions Height 140 mm 5 5 in Width 425 mm 16 7 in Depth 414 mm 16 3 in Weight Minimum configuration as shipped 10 0 kg 22 Ib Maximum configuration 11 4 kg 25 0 Ib Environment Air temperature System on
21. IBM de type ou d un type quivalent recommand par le fabricant La batterie contient du lithium et peut exploser en cas de mauvaise utilisation de mauvaise manipulation ou de mise au rebut inappropri e Ne pas Lancer ou plonger dans l eau e Chauffer plus de 100 C 212 F e R parer ou d sassembler Mettre au rebut les batteries usag es conform ment aux r glements locaux Modem safety information To reduce the risk of fire electrical shock or injury when using telephone equipment always follow basic safety precautions such as Never install telephone wiring during a lightning storm vi User Guide Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface Use caution when installing or modifying telephone lines Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning e Do not use the telephone to report a gas leak in the vicinity of the leak Consignes de s curit relatives au modem Lors de l utilisation de votre mat riel t l phonique il est important de respecter les consignes ci apr s afin de r duire les risques d incendie d lectrocution et d autres blessures e N installez jamais de cordons t l phon
22. Within Canada call 1 800 565 3344 or 1 800 IBM 4YOU Outside the United States and Canada contact your IBM reseller or IBM marketing representative Handling static sensitive devices Static electricity although harmless to you can seriously damage computer components and options When you add an option do not open the static protective package containing the option until you are instructed to do so When you handle options and other computer components take these precautions to avoid static electricity damage Limit your movement Movement can cause static electricity to build up around you Always handle components carefully Handle adapters and memory modules by the edges Never touch any exposed circuitry Prevent others from touching components When you install a new option touch the static protective package containing the option to a metal expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the package and your body When possible remove the option and install it directly in the computer without setting the option down When this is not possible place the static protective package that the option came in on a smooth level surface and place the option on it Do not place the option on the computer cover or other metal surface Chapter 1 Types 8301 and 8302 5 Installing external options This section shows the various external
23. any attached devices such as printers monitors and external drives Unplug all power cords from electrical outlets and remove the cover See Removing the cover in the chapter for your model Locate the Clear CMOS Recovery jumper on the system board See Identifying parts on the system board in the chapter for your model type If necessary refer to Installing adapters to remove any adapters that impede access to the Clear CMOS Recovery jumper Move the jumper from the standard position pins 1 and 2 to pins 2 and 3 Replace the cover See Replacing the cover and connecting the cables in the chapter for your model type Reconnect the power cords for the computer and monitor to electrical outlets Insert the POST BIOS update flash diskette into drive A and turn on the computer and the monitor After the update session is completed there will be no video and the series of beeps will end Remove the diskette from the diskette drive and turn off the computer and monitor Unplug the power cords from electrical outlets Remove the cover See Removing the cover in the chapter for your model type Remove any adapters that impede access to the BIOS Configuration jumper Replace the Clear CMOS Recovery jumper to its original position Replace any adapters that were removed Replace the cover and reconnect any cables that were disconnected Turn on the computer to restart the operating system Appendix B Manual
24. command 00 07 register 00D2 Channels 4 7 write request register 00 02 00D4 Channels 4 7 write single mask register bit 00 02 00D6 Channels 4 7 mode register write 00 07 00D8 Channels 4 7 clear byte pointer write N A 00DA Channels 4 7 master clear write temp 00 07 read 00DC Channels 4 7 clear mask register write 00 03 00DE Channels 4 7 write all mask register bits 00 03 00DF Channels 5 7 8 or 16 bit mode select 00 07 Appendix D Interrupt request and direct memory access channel assignments The following tables list the IRQ and DMA channel assignments Table 4 IRQ channel assignment IRQ System resource NMI Critical system error SMI System management interrupt for power management 0 Timer 1 Keyboard 2 Cascade interrupt from slave PIC 3 COM2 some models only 4 COM1 5 Available to user 6 Diskette controller 7 LPT1 8 Real time clock 9 Video ACPI 10 Available to user 11 Available to user 12 Mouse port 13 Math coprocessor 14 Primary IDE if present 15 Secondary IDE if present Note The default settings for COM 1 IRQ 4 COM 2 IRQ 3 and LPT 1 IRQ 7 can be changed to another IRQ Table 5 DMA channel assignments DMA Data width System resource 0 8 bits Open 1 8 bits Open 2 8 bits Diskette drive 3 8 bits Parallel port for ECP or EPP 4 Reserved ca
25. components A Identifying parts on the system board Installing memory Installing adapters Installing internal drives Drive specifications Installing a drive Installing a rope clip Changing the battery Z Erasing a lost or forgotten password cleating CMOS als Replacing the cover and connecting the abies Chapter 3 Types 8305 8306 8309 and 8313 Features Specifications Available options Tools required Handling static sensitive devices Installing external options Copyright IBM Corp 2002 Vi Vi Vi Vili IX ix X 1 1 4 29 6 6 8 9 9 12 13 13 13 14 14 16 16 17 18 19 19 20 23 23 24 25 27 28 28 31 al 34 33 35 35 36 Locating the connectors on the front of your computer Locating the conneeters on n the 1 rear nat your computer Obtaining device drivers Removing the cover Locating components Identifying parts on the system board Installing memory Installing adapters Installing internal drives Drive specifications Installing a drive Installing a rope clip Changing the battery Erasing a lost or forgotten password clearing CMOS Rb x Replacing the cover and connecting the cables Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 Features Specifications Available options Tools required Handling static sensitive devices Installing exte
26. drive that you are installing is set correctly as either a master or a slave device e If it is the first CD drive or DVD drive set it as a master device e If it is an additional CD drive or DVD drive set it as a slave device e If it is a hard disk drive set it as a slave device Refer to the documentation that comes with your drive for master slave jumper information Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 69 70 User Guide 6 Install the drive into the bay Align the screw holes and insert the screws that secure the drive to the bay 7 Each integrated drive electronics IDE drive requires two cables a four wire power cable that connects to the power supply and a signal cable that connects to the system board For a CD ROM drive you might also have an audio cable ODY The steps to connect an IDE drive are different depending on the type of drive you are connecting Use one of the following procedures for your drive connection Connecting the first IDE CD drive or DVD drive 1 Locate the three connector signal cable that comes with your computer or with the new drive Locate the secondary IDE connector on the system board See Identifying parts on the system board on page 63 Connect one end of the signal cable to the drive and the other to the secondary IDE connector on the system board To reduce electronic noise use the connectors at the end of the cable only You
27. for the addition of an integrated cable lock Startup sequence control Startup without diskette drive keyboard or mouse Unattended start mode Diskette and hard disk I O control Serial and parallel port I O control Security profile by device IBM preinstalled software Your computer might come with preinstalled software If it does an operating system device drivers to support built in features and other support programs are included Operating systems preinstalled varies by model type Note Not all countries or regions will have these operating systems e Microsoft Windows XP Home Microsoft Windows XP Professional Microsoft Windows 2000 Professional Operating systems tested for compatibility e Microsoft Windows NT Workstation Version 4 0 e Microsoft Windows 98 Second Edition e OS 2 The operating systems listed here are being tested for compatibility at the time this publication goes to press Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet Corrections and additions to this list are subject to change To determine if an operating system has been tested for compatibility check the Web site of the operating system vendor Chapter 2 Types 8303 8304 and 8312 11 Specifications This section lists the physical specifications for your computer Dimensions Height 104 mm 4 1 in Width 360 mm 1
28. map continued Address range hex Size bytes Description 03F0 03F5 6 Diskette channel 1 03F6 1 Primary IDE channel command port 03F7 Write 1 Diskette channel 1 command 03F7 bit 7 1 bit Diskette disk change channel 03F7 bits 6 0 7 bits Primary IDE channel status port 03F8 O3FF 8 COM1 0400 047F 128 Available 0480 048F 16 DMA channel high page registers 0490 OCF7 1912 Available OCF8 OCFB 4 PCI configuration address register OCFC OCFF 4 PCI configuration data register LPTn 400h 8 ECP port LPTn base address hex 400 OCF9 1 Turbo and reset control register 0D00 FFFF 62207 Available DMA I O address map The following table lists resource assignments for the DMA address map Any addresses that are not shown are reserved Table 3 DMA 1 0 address map Address hex Description Bits Byte pointer 0000 Channel 0 memory address register 00 15 Yes 0001 Channel 0 transfer count register 00 15 Yes 0002 Channel 1 memory address register 00 15 Yes 0003 Channel 1 transfer count register 00 15 Yes 0004 Channel 2 memory address register 00 15 Yes 0005 Channel 2 transfer count register 00 15 Yes 0006 Channel 3 memory address register 00 15 Yes 0007 Channel 3 transfer count register 00 15 Yes 0008 Channels 0 3 read status write command 00 07 register 0009 Channels 0 3
29. more information see Replacing the cover and connecting the cables on page 28 6 Thread the cable through the rope clip and around an object that is not a part of or permanently secured to the building structure or foundation and from which it cannot be removed then fasten the cable ends together with a lock M What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 28 26 User Guide Changing the battery Your computer has a special type of memory that maintains the date time and settings for built in features such as parallel port assignments configuration A battery keeps this information active when you turn off the computer The battery normally requires no charging or maintenance throughout its life however no battery lasts forever If the battery fails the date time and configuration information including passwords are lost An error message is displayed when you turn on the computer Refer to Lithium battery notice on page vil for information about replacing and disposing of the battery To change the battery 1 PON Turn off the computer and all attached devices Remove the cover See Removing the cover on page 17 Locate the battery See Identifying parts on the system board on page 18 If necessary remove any adapters that impede access
30. off W 3 6 W 3 6 W 3 6 W 3 6 W Energy consumption efficiency class Q Q Q Q Class Q Criteria 0 12 0 12 0 12 0 12 CTP in MTOPS 4800 5333 6027 6400 1 8GHz 2 0GHz 2 26GHz 2 4GHz Energy consumption efficiency value 0 00086 0 00077 0 00068 0 00064 Types 8305 and 8306 1 8GHz 2 0GHz 2 26GHz 2 4GHz Normal Power consumption W 59 W 58 W 61 W 64 W Maximum power consumption W VA 172 W 152 W 160 W 167 W 219 VA 194 VA 203 VA 210 VA Wattage when suspend W 3 1 W 3 1 W 3 1 W 3 1 W Wattage when power off W 2 7 W 2 7 W 2 7 W 2 7 W Energy consumption efficiency class Q Q Q Q Class Q Criteria 0 12 0 12 0 12 0 12 CTP in MTOPS 4800 5333 6027 6400 Energy consumption efficiency value 0 00065 0 00058 0 00051 0 00048 Type 8307 1 8GHz 2 0GHz 2 26GHz 2 4GHz Normal Power consumption W 59 W 58 W 61 W 64 W Maximum power consumption W VA 180 W 160 W 169 W 174 W 232 VA 204 VA 1213 VA 220 VA Wattage when suspend W 3 1 W 3 1 W 3 1 W 3 1 W Wattage when power off W 2 7 W 2 7 W 2 7 W 2 7 W Energy consumption efficiency class Q Q Q Q Class Q Criteria 0 12 0 12 0 12 0 12 CTP in MTOPS 4800 5333 6027 6400 Energy consumption efficiency value 0 00065 0 00058 0 00051 0 00048 Type 8309 1 8GHz 1
31. settings in the IBM Setup Utility program Starting the IBM Setup Utility program To start the IBM Setup Utility program do the following 1 If your computer is already on when you start this procedure shut down the operating system and turn off the computer 2 Turn on the computer and look for the following prompt on the logo screen To interrupt normal startup press Enter Press Enter when you see the prompt 3 When the Startup Interrupt Menu displays press F1 Note If an administrator password has been set the IBM Setup Utility program menu is not displayed until you type your password See ee more information The IBM Setup Utility might start automatically when POST detects that hardware has been removed or new hardware has been installed in your computer Viewing and changing settings The IBM Setup Utility program menu lists items that identify system configuration topics When working with the IBM Setup Utility program menu you must use the keyboard The keys used to perform various tasks are displayed at the bottom of each screen Exiting from the IBM Setup Utility program When you finish viewing or changing settings press Esc to return to the IBM Setup Utility program menu you might have to press Esc several times If you want to save the new settings select Save Settings before you exit Otherwise your changes will not be saved Using passwords You can use passwords to provide securit
32. static protective package 4 Install the adapter into the appropriate slot on the system board 5 Install the adapter slot cover latch 66 User Guide What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 74 Installing internal drives This section provides information and instructions for installing and removing internal drives Internal drives are devices that your computer uses to read and store data You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media Some of the different drives that are available for your computer are e Hard disk drives e CD drives or DVD drives e Removable media drives Internal drives are installed in bays In this book the bays are referred to as bay 1 bay 2 and so on When you install an internal drive it is important to note what type and size of drive that you can install in each bay Also it is important to correctly connect the internal drive cables to the installed drive Drive specifications Your computer comes with the following IBM installed drives e ACD drive or DVD drive in bay 1 some models e A 3 5 inch diskette disk drive in bay 3 e A 3 5 inch hard drive in bay 4 Any bay that does not have a drive installed has a static shield and bay panel installed Chapter 4 Ty
33. to the battery See Installing adapters on page 20 for more information Remove the old battery Install the new battery Replace any adapters that were removed to gain access to the battery See Installing adapters on page 20 for instructions for replacing adapters Replace the cover and plug in the power cord See Replacing the cover and connecting the cables on page 28 Note When the computer is turned on for the first time after battery replacement an error message might be displayed This is normal after replacing the battery Turn on the computer and all attached devices Use the IBM Setup Utility program to set the date and time and an passwords See Chapter 5 Using the IBM Setup Utility program on page 77 Chapter 2 Types 8303 8304 and 8312 27 Erasing a lost or forgotten password clearing CMOS This section applies to lost or forgotten passwords For more information about lost or forgotten passwords see Access IBM on your desktop To erase a forgotten password If necessary see Turn off the computer and all attached devices Remove the cover See Removing the cover on page 17 Locate the Clear CMOS Recover jumper on the system board See Identifying parts on the system board on page 18 Installing adapters on page 20 to remove any adapters that impede access to the Clear
34. to the drive Connecting an additional IDE hard disk drive 1 Locate the primary IDE connector on the system board One end of the three connector cable connects to the hard disk drive and the other connects to the system board See Identifying parts on the system board on page 40 2 Connect the extra connector in the signal cable to the new hard disk drive 3 Your computer has extra power connectors for additional drives Connect a power connector to the drive r What to do next To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 51 Installing a rope clip 48 User Guide To help prevent hardware theft you can add a 3 16 inch or 5 mm rope clip and cable to your computer After you add the security cable make sure that it does not interfere with other cables that are connected to the computer For more information about security see Installing a cable lock in Access IBM To install a rope clip 1 Remove the cover See Removing the cover on page 39 2 Use a tool such as a screwdriver to remove the two metal knockouts 3 Insert the rope clip through the rear panel then attach and tighten the nuts with an appropriately sized or adjustable wrench 4 Replace the computer cover For more information see Replacing the cover and connecting the cables on page 51
35. update the configuration see Chapter 5 Using the IBM Setup Utilit Chapter 2 Types 8303 8304 and 8312 29 30 User Guide Chapter 3 Types 8305 8306 8309 and 8313 This chapter provides an introduction to the features and options that are available for your computer You can expand the capabilities of your computer by adding memory adapters or drives When installing an option use these instructions along with the instructions that come with the option Important Before you install or remove any option read Safety Information on page v These precautions and guidelines will help you work safely Features This section provides an overview of the computer features and preinstalled software Microprocessor varies by model type Intel Pentium 4 processor with 256 KB or 512 KB of internal L2 cache memory and Intel NetBurst micro architecture Memory Support for two dual inline memory modules DIMMs e 512 KB flash memory for system programs Internal drives e 3 5 inch 1 44 MB diskette drive e Internal hard disk drive e EIDE CD drive or DVD drive some models Video subsystem Intel Extreme graphics Accelerated graphics port AGP video adapter slot on the system board some models Audio subsystem Integrated SoundMAX 3 audio Copyright IBM Corp 2002 31 32 User Guide Connectivity 10 100 Mbps integrated Intel Ethernet controller that supports the Wake
36. you can purchase a USB hub which you can use to connect additional USB devices Used to attach a parallel printer parallel scanner or other devices that use a 25 pin parallel connector Used to attach an Ethernet cable for a local area network LAN Note To operate the computer within FCC Class B limits use a Category 5 Ethernet cable Used to attach a microphone to your computer when you want to record voice or other sounds on the hard disk if you use speech recognition software Used to send audio signals from the computer to external devices such as powered stereo speakers speakers with built in amplifiers headphones multimedia keyboards or the audio line in connector on a stereo system or other external recording device Used to receive audio signals from an external audio device such as a stereo system When you attach an external audio device a cable is connected between the audio line out connector of the device and the audio line in connector of the computer Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http www ibm com pc support on the World Wide Web Installation instructions are provided in README files with the device driver files 60 User Guide Removing the cover m Important Read Safety Information on page vland Handling static sensitive devices before removing the cover To remove the cover 1 Shut
37. 070 bits 6 0 6 bits Real time clock address 0071 1 Real time clock data 0072 1 bit Enable NMI 0072 bits 6 0 6 bits RTC address 0073 1 RTC data 0080 1 POST checkpoint register during POST only 008F 1 Refresh page register 0080 008F 16 DMA page registers 0090 0091 15 General I O locations available to PCI bus 0092 1 PS 2 keyboard controller registers 0093 009F 15 General I O locations 00A0 00A1 2 Interrupt controller 2 00A2 OOBF 30 APM control 00C0 00DF 31 DMA 2 OOEO OOEF 16 General I O locations available to PCI bus OOFO 1 Coprocessor error register OOF1 016F 127 General I O locations available to PCI bus 0170 0177 8 Secondary IDE channel O1F0 01F7 8 Primary IDE channel 0200 0207 8 MIDI joystick port 0220 0227 8 Serial port 3 or 4 0228 0277 80 General I O locations available to PCI bus 0278 027F 8 LPT3 0280 02E7 102 Available 02E8 02EF 8 Serial port 3 or 4 02F8 02FF 8 COM2 0338 033F 8 Serial port 3 or 4 0340 036F 48 Available 0370 0371 2 IDE channel 1 command 0378 037F 8 LPT2 0380 03B3 52 Available 03B4 03B7 4 Video 03BA 1 Video 03BC 03BE 16 LPT1 03C0 03CF 52 Video 03D4 03D7 16 Video 03DA 1 Video 03D0 03DF 11 Available 03E0 03E7 8 Available 03E8 03EF 8 COM3 or COM4 Table 2 1 0 address
38. 4 2 in Depth 412 mm 16 2 in Weight Minimum configuration as shipped 8 1 kg 18 Ib Maximum configuration 9 1 kg 20 Ib Environment Air temperature System on 10 to 35 C 50 to 95 F System off 10 to 43 C 50 to 110 F Maximum altitude 2134 m 7000 ft Note The maximum altitude 2134 m 7000 ft is the maximum altitude at which the specified air temperatures apply At higher altitudes the maximum air temperatures are lower than those specified Humidity System on 8 to 80 System off 8 to 80 Electrical input Input voltage Low range Minimum 90 V ac Maximum 137 V ac Input frequency range 57 63 Hz Voltage switch setting 115 V ac High range Minimum 180 V ac Maximum 265 V ac Input frequency range 47 53 Hz Voltage switch setting 230 V ac Input kilovolt amperes kVA approximate Minimum configuration as shipped 0 08 kVA Maximum configuration 0 30 kVA Note Power consumption and heat output vary depending on the number and type of optional features installed and the power management optional features in use Heat output approximate in British thermal units Btu per hour Minimum configuration 257 Btu hr 75 watts Maximum configuration 806 Btu hr 235 watts Airflow Approximately 0 45 cubic meters per minute 16 cubic feet per minute maximum Acoustical noise emission values Average sound pressure levels At operator position Idle 32 dBA Operating 35 dBA At byst
39. CD ROM drive and DVD ROM drive some models Hard disk drive Diskette drives and other removable media drives For the latest information about available options see the following World Wide Web pages e http www ibm com pc us options e http www ibm com pc support You can also obtain information by calling the following telephone numbers Within the United States call 1 800 IBM 2YOU 1 800 426 2968 your IBM reseller or IBM marketing representative e Within Canada call 1 800 565 3344 or 1 800 IBM 4YOU Outside the United States and Canada contact your IBM reseller or IBM marketing representative Tools required To install some options in your computer you might need a flat blade or Phillips screwdriver Additional tools might be needed for certain options See the instructions that come with the option Handling static sensitive devices Static electricity although harmless to you can seriously damage computer components and options When you add an option do not open the static protective package containing the option until you are instructed to do so When you handle options and other computer components take these precautions to avoid static electricity damage Chapter 2 Types 8303 8304 and 8312 13 Limit your movement Movement can cause static electricity to build up around you Always handle components carefully Handle adapters and memory modules by the edges Never touch any e
40. NetVista User Guide Type 8301 8302 8303 8304 8305 Type 8306 8307 8308 8309 8310 Type 8311 8312 8315 8314 8315 at NetVista User Guide Type 8301 8302 8303 8304 8305 Type 8306 8307 8308 8309 8310 Type 8311 8312 8315 8314 8315 at Note Before using this information and the product it supports be sure to read the Safety Information on page vland Appendix E Notices on page 97 First Edition April 2002 Copyright International Business Machines Corporation 2002 All rights reserved US Government Users Restricted Rights Use duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp Contents Safety Information Lithium battery notice Modem safety information Laser compliance statement Overview Information resources Identifying your computer Chapter 1 Le 8301 and 8302 Features Specifications Available options Handling static sensitive devices Installing external options Locating connectors on the front of your computer Locating the connectors on the rear of your computer Chapter 2 Nee 8303 8304 and 8312 Features Specifications Available options Tools required Handling static sensitive devices Installing external options Locating the connectors on the front of your computer 2 Locating the connectors on a thei rear rof your computer a Obtaining device drivers Removing the cover Locating
41. Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both IBM NetVista Wake on LAN PS 2 OS 2 Intel Pentium NetBurst and Extreme are trademarks of Intel Corporation in the United States other countries or both Microsoft Windows and Windows NT are trademarks of Microsoft Corporation in the United States other countries or both Other company product and service names may be trademarks or service marks of others PC Green label compliance information Japan 98 User Guide Type 8301 1 8GHz 2 0GHz 2 26GHz 2 4GHz Normal Power consumption W 58 W 58 W 61 W 64 W Maximum power consumption W VA 145 W 116 W 126 W 131 W 181 VA 147 VA 159 VA 165 VA Wattage when suspend W 3 1 W 3 1 W 3 1 W 3 1 W Wattage when power off W 2 7 W 2 7 W 2 7 W 2 7 W Energy consumption efficiency class Q Q Q Q Class Q Criteria 0 12 0 12 0 12 0 12 CTP in MTOPS 4800 5333 6027 6400 Energy consumption efficiency value 0 00065 0 00058 0 00051 0 00048 Types 8303 and 8304 1 8GHz 2 0GHz 2 26GHz 2 4GHz Normal Power consumption W 58 W 58 W 60 W 65 W Maximum power consumption W VA 153 W 130 W 1138 W 141 W 192 VA 163 VA 171 VA 178 VA Wattage when suspend W 4 1 W 4 1 W 4 1 W 4 1 W Wattage when power
42. a POST BIOS update failure 82 removing the cover Types 8303 8304 and 8312 17 Types 8305 8306 8309 and 8313 39 Types 8307 8308 8310 8311 8314 and 8315 61 replacing the cover Types 8303 8304 and 8312 28 Types 8305 8306 8309 and 8313 51 Types 8307 8308 8310 8311 8314 and 8315 74 S security features 2 10 32 54 rope clip 25 48 71 security profile by device 78 serial connectors 8 16 38 60 system address maps 91 system board connectors 19 41 64 identifying parts 18 40 63 location 19 41 64 memory 13 19 35 41 57 64 system programs 81 102 User Guide U USB connectors 8 16 38 60 using security profile by device 78 V video subsystem 1 9 31 53 Part Number 49P0935 Printed in U S A 1P P N 49P0935
43. ables as described in the following table when installing moving or opening covers on this product or attached devices To connect To disconnect 1 Turn everything OFF 1 Turn everything OFF 2 First attach all cables to devices 2 First remove power cords from outlet 3 Attach signal cables to connectors 3 Remove signal cables from connectors 4 Attach power cords to outlet 4 Remove all cables from devices 5 Turn device ON DANGER Le courant lectrique provenant de l alimentation du t l phone et des c bles de transmission peut pr senter un danger Pour viter tout risque de choc lectrique Copyright IBM Corp 2002 Ne manipulez aucun c ble et n effectuez aucune op ration d installation d entretien ou de reconfiguration de ce produit au cours d un orage Branchez tous les cordons d alimentation sur un socle de prise de courant correctement c bl et mis la terre Branchez sur des socles de prise de courant correctement c bl s tout quipement connect ce produit Lorsque cela est possible n utilisez qu une seule main pour connecter ou d connecter les cables d interface Ne mettez jamais un quipement sous tension en cas d incendie ou d inondation ou en pr sence de dommages mat riels Avant de retirer les carters de l unit mettez celle ci hors tension et d connectez ses cordons d alimentation ainsi que les cables qui la relient aux r seaux au
44. aintenance throughout its life however no battery lasts forever If the battery fails the date time and configuration information including passwords are lost An error message is displayed when you turn on the computer Refer to Lithium battery notice on page vilfor information about replacing and disposing of the battery To change the battery 1 Turn off the computer and all attached devices Remove the cover See Removing the cover on page 61 Locate the battery See Identifying parts on the system board on page 63 If necessary remove any adapters that impede access to the battery See Installing adapters on page 65 for more information 5 Remove the old battery PON 6 Install the new battery me 7 Replace any adapters that were removed to gain access to the battery See Installing adapters on page 65 for instructions for replacing adapters 8 Replace the cover and plug in the power cord See Replacing the cover and connecting the cables on page 74 Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 73 Note When the computer is turned on for the first time after battery replacement an error message might be displayed This is normal after replacing the battery Turn on the computer and all attached devices Use the IBM Setup Utility program to set the date and time and an passwords
45. al detection Z_ ZO Reset and retrieve active profile 0 Z1 Reset and retrieve active profile 1 84 User Guide Extended AT commands Command Function amp C_ amp CO Force Carrier Detect Signal High ON amp C1 Turn on CD when remote carrier is present amp D_ amp DO Modem ignores the DTR signal amp D1 Modem returns to Command Mode after DTR toggle amp D2 Modem hangs up returns to the Command Mode after DTR toggle amp D3 Resets modem after DTR toggle amp F_ amp F Recall factory default configuration amp G_ amp G0 Guard tone disabled amp G1 Guard tone disabled amp G2 1800 Hz guard tone amp K_ amp KO Disable flow control amp K3 Enable RTS CTS hardware flow control amp K4 Enable XON XOFF software flow control amp K5 Enable transparent XON XOFF flow control amp K6 Enable both RTS CTS and XON XOFF flow control amp M_ amp MO Asynchronous operation amp P_ amp P0 US setting for off hook to on hook ratio amp P1 UK and Hong Kong off hook to on hook ratio amp P2 Same as amp P0 setting but at 20 pulses per minute amp P3 Same as amp P1 setting but at 20 pulses per minute amp R_ amp RO Reserved amp R1 CTS operates per flow control requirements amp S_ amp S0 Force DSR Signal High ON amp S1 DSR off in command mode on in on line mode amp T_ amp TO Ends test in progress amp T1 Perform Local Analog Loopback Tes
46. an external audio device a cable is connected between the audio line out connector of the device and the audio line in connector of the computer Used to send audio signals from the computer to external devices such as powered stereo speakers speakers with built in amplifiers headphones multimedia keyboards or the audio line in connector on a stereo system or other external recording device Used to attach a microphone to your computer when you want to record voice or other sounds on the hard disk if you use speech recognition software Used to attach a device that requires a Universal Serial Bus USB connection such as a USB scanner or USB printer If you have more than four USB devices you can purchase a USB hub which you can use to connect additional USB devices Used to attach a keyboard that uses a standard keyboard connector Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http www ibm com pc support on the World Wide Web Installation instructions are provided in README files with the device driver files 38 User Guide Removing the cover m Important Read Safety Information on page vland Handling static sensitive devices on page 35 before removing the cover To remove the cover 1 Shut down your operating system remove any media diskettes CDs or tapes from the drives and turn off all attached devices and the com
47. ander position 1 meter 3 3 ft Idle 29 dBA Operating 33 dBA Declared upper limit sound power levels Idle 4 4 bels Operating 4 7 bels Note These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute ANSI 12 10 and ISO 7779 and are reported in accordance with ISO 9296 Actual sound pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources The declared sound power levels indicate an upper limit below which a large number of computers will operate Note See the Quick Reference for the classification of your computer 12 User Guide Available options The following are some available options e External options Parallel port devices such as printers and external drives Serial port devices such as external modems and digital cameras Audio devices such as external speakers for the sound system USB devices such as printers joysticks and scanners Security device such as a rope clip Monitors IEEE 1394 devices requires an IEEE 1394 adapter Internal options System memory called dual inline memory modules DIMMs Peripheral component interconnect PCI adapters supports low profile adapters only Accelerated graphics port AGP adapters supports low profile adapters only Internal drives such as
48. ands Extended AT commands MNP V 42 V 42bis V 44 commands Fax Class 1 commands iv User Guide 78 78 79 279 79 81 81 81 81 82 83 83 85 86 87 Fax Class 2 commands Voice commands Appendix C System address maps System memory map I O address map DMA I O address map Appendix D Interrupt request and direct memory access channel assignments Appendix E Notices Television output notice Trademarks PC Green label compliance information Japan Index 87 88 91 91 91 93 95 97 97 98 100 101 Safety Information DANGER Electrical current from power telephone and communication cables is hazardous To avoid a shock hazard Do not connect or disconnect any cables or perform installation maintenance or reconfiguration of this product during an electrical storm Connect all power cords to a properly wired and grounded electrical outlet Connect to properly wired outlets any equipment that will be attached to this product When possible use one hand only to connect or disconnect signal cables Never turn on any equipment when there is evidence of fire water or structural damage Disconnect the attached power cords telecommunications systems networks and modems before you open the device covers unless instructed otherwise in the installation and configuration procedures Connect and disconnect c
49. at are greater than 43 0 mm 1 7 in high cannot be installed 2 Install removable media tape or CD drives in the accessible bay bay 1 or 2 Installing a drive To install an internal drive follow these steps 1 Remove the cover See Removing the cover on page 39 2 If your computer has a CD drive or DVD drive you might need to remove the signal and power cables from the drive 3 Ifthe drive you are installing is a removable media drive remove the bay panel from the front bezel Chapter 3 Types 8305 8306 8309 and 8313 45 4 Remove the metal shield from the drive bay by inserting a flat blade screwdriver into one of the slots and gently prying it loose 5 Pivot the drive bay latch handle toward the front of the computer and then pivot the drive bay cage upward as shown until it is latched in the upright position 6 Make sure the drive that you are installing is set correctly as either a master or a slave device e If it is a hard disk drive set it as a slave device e If it is the first CD drive or DVD drive set it as a master device e If it is an additional CD drive or DVD drive set it as a slave device Refer to the documentation that comes with your drive for master slave jumper information 46 User Guide 7 Install the drive into the bay Align the screw holes and insert the two screws 8 Pivot the drive bay cage back into place 9 Each integrated drive electronics IDE dri
50. ate section e To complete the installation go to Replacing the cover and connecting the cables on page 28 22 User Guide Installing internal drives This section provides information and instructions for installing and removing internal drives Internal drives are devices that your computer uses to read and store data You can add or replace drives to your computer to increase storage capacity and to enable your computer to read other types of media such as CD ROM Internal drives are installed in bays In this book the bays are referred to as bay 1 bay 2 and so on When you install an internal drive it is important to note what type and size of drive that you can install in each bay Also it is important to correctly connect the internal drive cables to the installed drive Drive specifications Your computer might come with the following IBM installed drives e A3 5 inch diskette drive in bay 1 e A CD ROM drive or DVD ROM drive in bay 2 some models e A3 5 inch hard disk drive in bay 3 Any bay that does not have a drive installed has a static shield and bay panel installed The following illustration shows the locations of the drive bays The following list describes some of the drives that you can install in each bay and their height requirements Bay 1 Maximum height 25 8 mm 1 0 in 3 5 inch diskette drive preinstalled A Bay 2 Maximum height 43 0 mm 1 7 in CD ROM drive or DVD ROM driv
51. ble for a local area network LAN Note To operate the computer within FCC Class B limits use a Category 5 Ethernet cable Used to receive audio signals from an external audio device such as a stereo system When you attach an external audio device a cable is connected between the audio line out connector of the device and the audio line in connector of the computer Used to send audio signals from the computer to external devices such as powered stereo speakers speakers with built in amplifiers headphones multimedia keyboards or the audio line in connector on a stereo system or other external recording device Used to attach a microphone to your computer when you want to record voice or other sounds on the hard disk if you use speech recognition software Used to attach a device that requires a Universal Serial Bus USB connection such as a USB scanner or USB printer If you have more than four USB devices you can purchase a USB hub which you can use to connect additional USB devices Used to attach a keyboard that uses a standard keyboard connector Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http www ibm com pc support on the World Wide Web Installation instructions are provided in README files with the device driver files 16 User Guide Removing the cover m Important Read Safety Information on page vjand Handling static sens
52. cimal hex 0 K 512 KB 00000 7FFFF 512 KB Conventional 512 K 639 KB 80000 9FBFF 127 KB Extended conventional 639 K 640 KB 9FCOO 9FFFF 1 KB Extended BIOS data 640 K 767 KB A0000 BFFFF 128 KB Dynamic video memory display cache 768 K 800 KB C0000 C7FFF 32 KB Video ROM BIOS shadowed 800 K 896 KB C8000 DFFFF 96 KB PCI space available to adapter ROMs 896 K 1MB E0000 FFFFF 128 KB System ROM BIOS main memory shadowed 1 MB 16 MB 1000000 FFFFFF 15 MB PCI space 16 MB 4096 MB 10000000 4080 MB PCI space positive decode FFDFFFFF FFFEO000 128 KB System ROM BIOS FFFFFFFF I O address map The following table lists resource assignments for the I O address map Any addresses that are not shown are reserved Table 2 I O address map Address range hex Size bytes Description 0000 000F 16 DMA 1 0010 001F 16 General I O locations available to PCI bus 0020 0021 2 Interrupt controller 1 0022 003F 30 General I O locations available to PCI bus 0040 0043 4 Counter timer 1 0044 OOFF 28 General I O locations available to PCI bus 0060 1 Keyboard controller byte reset IRQ 0061 1 System port B 0064 1 Keyboard controller CMD ATAT byte 0070 bit 7 1 bit Enable NMI Copyright IBM Corp 2002 91 92 User Guide Table 2 1 0 address map continued Address range hex Size bytes Description 0
53. connectors on your computer to which you can attach external options such as external speakers a printer or a scanner For some external options you must install additional software in addition to making the physical connection When adding an external option use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option Locating connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer USB connector A USB connector 6 User Guide Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer FE ea ET O El E a 6 Serial connector E Microphone connector H Mouse connector E USB connectors Parallel connector VGA monitor connector E Ethernet connector Serial connector E Audio line in connector USB connectors El Power connector Keyboard connector Audio line out connector Note Some connectors on the rear of the computer are color coded to help you to determine where to connect the cables on your computer Chapter 1 Types 8301 and 8302 7 8 User Guide Connector Serial connector Mouse connector Parallel connector Ethernet co
54. down your operating system remove any media diskettes CDs or tapes from the drives and turn off all attached devices and the computer Unplug all power cords from electrical outlets Disconnect all cables attached to the computer This includes power cords input output I O cables and any other cables that are connected to the computer on gt Press the cover release button on the left side cover and remove the cover Im SA SEAT SER SEEN TELE PS RS SITE Rd THe Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 61 Locating components The following illustration will help you locate the various components in your computer Microprocessor and heat sink EX PCI adapter A DIMMs H Power supply AGP slot some models Moving the power supply To perform some operations inside the computer you might need to move the power supply to access parts of the system board that are difficult to see or hard to reach Use the following procedure to provide easier access to the system board 1 Locate the power supply See Locating components on page 62 62 User Guide 2 Push the plastic tab to release the power supply To replace the power supply reverse these steps Identifying parts on the system board The system board sometimes called the planar or motherboard is the main circuit board in your computer It provides basic com
55. e preinstalled in some models Bay 3 Maximum height 25 8 mm 1 0 in 3 5 inch hard disk drive preinstalled Notes 1 Drives that are greater than 43 0 mm 17 in high cannot be installed 2 Install removable media tape or CD drives in the accessible bay bay 2 Chapter 2 Types 8303 8304 and 8312 23 Installing a drive To install a CD ROM drive or DVD ROM drive in bay 2 follow these steps 1 Remove the cover see Removing the cover on page 17 2 If the drive you are installing is a removable media drive remove the bay panel from the front bezel 3 Remove the metal shield from the drive bay by inserting a flat blade screwdriver into one of the slots and gently prying it loose 4 Make sure the drive is set correctly as the master device Refer to the documentation that comes with your CD ROM drive or DVD ROM drive for master slave jumper information 5 Pivot the drive bay latch handle toward the front of the computer and then pivot the drive bay cage upward as shown until it is latched in the up position 24 User Guide 7 Each integrated drive electronics IDE drive requires two cables a four wire power cable that connects to the power supply and a signal cable that connects to the system board To connect a CD ROM drive or DVD ROM drive to your computer follow these steps a Locate the signal cable that comes with your computer or with the new drive b Locate the secondary IDE connecto
56. e Characters Switch from Data Mode to Command Mode T I E S Command H HO Force modem on hook hang up Copyright IBM Corp 2002 83 Command Function H1 Force modem off hook make busy Note H1 command is not supported for Italy L 10 Display product identification code Il Factory ROM checksum test 12 Internal memory test 13 Firmware ID 14 Reserved ID L_ LO Low speaker volume L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume M_ MO Internal speaker off M1 Internal speaker on until carrier detected M2 Internal speaker always on M3 Internal speaker on until carrier detected and off while dialing N_ Included for compatibility only provides no effect O_ O0 Return to Data Mode O1 Return to Data Mode and initiate an equalizer retrain P Set Pulse dial as default Q_ Q0 Modem sends responses Sr Read and display value in register r Sr n Set register r to value n n 0 255 T Set Tone Dial as default V_ VO Numeric responses V1 Word responses W_ wo Report DTE speed only wi Report line speed error correction protocol and DTE speed W2 Report DCE speed only X_ X0 Hayes Smartmodem 300 compatible responses blind dialing X1 Same as X0 plus all CONNECT responses blind dialing X2 Same as X1 plus dial tone detection X3 Same as X1 plus busy detection blind dialing X4 All responses and dial tone and busy sign
57. e sure that it does not interfere with other cables that are connected to the computer For more information about security see Installing a cable lock in Access IBM To install a rope clip 1 Remove cover see Removing the cover on page 61 Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 71 2 Use a tool such as a screwdriver to remove the two metal knockouts 3 Insert the rope clip through the rear panel then attach and tighten the nuts with an appropriately sized or adjustable wrench SER SEEN SC SER SEO TER 4 Replace the computer cover For more information see Replacing the cover and connecting the cables on page 74 72 User Guide 5 Thread the cable through the rope clip and around an object that is not a part of or permanently secured to the building structure or foundation and from which it cannot be removed then fasten the cable ends together with a lock m What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 74 Changing the battery Your computer has a special type of memory that maintains the date time and settings for built in features such as parallel port assignments configuration A battery keeps this information active when you turn off the computer The battery normally requires no charging or m
58. f media Some of the different drives that are available for your computer are e Hard disk drives Tape drives CD drives or DVD drives Removable media drives Internal drives are installed in bays In this book the bays are referred to as bay 1 bay 2 and so on When you install an internal drive it is important to note what type and size of drive that you can install in each bay Also it is important to correctly connect the internal drive cables to the installed drive Drive specifications 44 User Guide Your computer comes with the following IBM installed drives ACD drive or DVD drive in bay 1 some models e A 3 5 inch hard disk drive in bay 3 e A 3 5 inch diskette drive in bay 4 Any bay that does not have a drive installed has a static shield and bay panel installed The following illustration shows the locations of the drive bays X Q The following list describes some of the drives that you can install in each bay and their height requirements Bay 1 Maximum height 43 0 mm 1 7 in CD drive or DVD drive preinstalled in some models 5 25 inch hard disk drive A Bay 2 Maximum height 43 0 mm 1 7 in 5 25 inch hard disk drive 3 5 inch hard disk drive requires a mounting bracket CD drive DVD drive Bay 3 Maximum height 25 8 mm 1 0 in 3 5 inch hard disk drive preinstalled a Bay 4 Maximum height 25 8 mm 1 0 in 3 5 inch diskette drive preinstalled Notes 1 Drives th
59. g telephone lines and power cords Also depending on the option that is installed you might need to confirm the updated information in the IBM Setup Utility program To replace the cover and connect cables to your computer Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer 2 Clear any cables that might impede the replacement of the cover 3 Position the cover on the chassis so that the rail guides on the bottom of the cover engage the rails and push the cover closed until it latches 4 Reconnect the external cables and power cords to the computer See Installing external options on page 58 5 To update the configuration see Chapter 5 Using the IBM Setup Utilit fr Important When the power cord is first plugged in the computer might appear to turn on for a few seconds and then turn off This is a normal sequence to enable the computer to initialize Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 75 76 User Guide Chapter 5 Using the IBM Setup Utility program The IBM Setup Utility program is stored in the electrically erasable programmable read only memory EEPROM of your computer The IBM Setup Utility program is used to view and change the configuration settings of your computer regardless of which operating system you are using However the operating system settings might override any similar
60. han those specified herein might result in hazardous radiation exposure Removing the covers of the CD ROM drive or DVD ROM drive could result in exposure to hazardous laser radiation There are no serviceable parts inside the CD ROM drive or DVD ROM drive Do not remove the drive covers Some CD ROM drives and DVD ROM drives contain an embedded Class 3A or Class 3B laser diode Note the following statement Safety Information vii viii User Guide DANGER Laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam DANGER Certains mod les d ordinateurs personnels sont quip s d origine d une unit de CD ROM ou de DVD ROM Mais ces unit s sont galement vendues s par ment en tant qu options L unit de CD ROM DVD ROM est un appareil laser Aux Etat Unis l unit de CD ROM DVD ROM est certifi e conforme aux normes indiqu es dans le sous chapitre J du DHHS 21 CFR relatif aux produits laser de classe 1 Dans les autres pays elle est certifi e tre un produit laser de classe 1 conforme aux normes CEI 825 et CENELEC EN 60 825 Lorsqu une unit de CD ROM DVD ROM est install e tenez compte des remarques suivantes ATTENTION Pour viter tout risque d exposition au rayon laser respectez les consignes de r glage et d utilisation des commandes ainsi que les proc dures d crites L ouverture de l unit
61. ing illustration shows the locations of the connectors on the back of the computer j 3 FS AO 0 10 A Of 4 lol RAR ddl geo Serial connector E Ethernet connector H Mouse connector Microphone connector Keyboard connector Audio line out connector EI USB connectors Audio line in connector H Serial connector AGP slot some models BE Parallel connector PCI slots VGA monitor connector Power connector EJ USB connectors Note Some connectors on the rear of the computer are color coded to help you to determine where to connect the cables on your computer Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 59 Connector Serial connector Mouse connector Keyboard connector USB connectors Parallel connector Ethernet connector Microphone connector Audio line out connector Audio line in connector Description Used to attach an external modem serial printer or other devices that use a 9 pin serial connector Used to attach a mouse trackball or other pointing device that uses a standard mouse connector Used to attach a keyboard that uses a standard keyboard connector Used to attach a device that requires a Universal Serial Bus USB connection such as a USB scanner or USB printer If you have more than four USB devices
62. intenance or upgrade and not for daily security e EIDE CD ROM drive some models Video subsystem Intel Extreme graphics Audio subsystem Integrated SoundMAX 3 audio Connectivity 10 100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN feature Copyright IBM Corp 2002 1 2 User Guide System management features Remote Program Load RPL and Dynamic Host Configuration Protocol DHCP e Wake on LAN Wake on Ring in the IBM Setup Utility program this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem Remote Administration Automatic power on startup System Management SM BIOS and SM software Ability to store POST hardware test results Input output features e 25 pin Extended Capabilities Port ECP Extended Parallel Port EPP e Two 9 pin serial connectors Six 4 pin USB connectors PS 2 mouse connector e PS 2 keyboard connector e Ethernet connector e VGA monitor connector Three audio connectors line in line out and microphone Expansion Two drive bays Power e 125 W power supply with manual voltage selection switch Automatic 50 60 Hz input frequency switching Advanced Power Management support Advanced Configuration and Power Interface ACPI support Security features User and administrator passwords Support for the addition of a rope clip and lockable cable Suppor
63. ion by calling the following telephone numbers e Within the United States call 1 800 IBM 2YOU 1 800 426 2968 your IBM reseller or IBM marketing representative e Within Canada call 1 800 565 3344 or 1 800 IBM 4YOU Outside the United States and Canada contact your IBM reseller or IBM marketing representative Tools required To install some options in your computer you might need a flat blade or Phillips screwdriver Additional tools might be needed for certain options See the instructions that come with the option Handling static sensitive devices Static electricity although harmless to you can seriously damage computer components and options When you add an option do not open the static protective package containing the option until you are instructed to do so When you handle options and other computer components take these precautions to avoid static electricity damage Limit your movement Movement can cause static electricity to build up around you Always handle components carefully Handle adapters and memory modules by the edges Never touch any exposed circuitry Chapter 3 Types 8305 8306 8309 and 8313 35 Prevent others from touching components When you install a new option touch the static protective package containing the option to a metal expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the
64. ion identification FCR Capability to receive FCR Capability to receive FCSI Report the called station ID FDCC DCE capabilities parameters FDCS Report current session FDCS Current session results FDIS Report remote capabilities FDIS Current sessions parameters FDR Begin or continue phase C receive data FDT Data transmission FDTC Report the polled station capabilities FET Post page message response FET N Transmit page punctuation FHNG Call termination with status FK Session termination FLID FLPL Local ID string Document for polling FMDL FMFR Identify model Identify manufacturer Appendix B Manual modem commands 87 FPHCTO Phase C time out FPOLL Indicates polling request FPTS Page transfer status FPTS Page transfer status FREV Identify revision FSPT Enable polling FTSI Report the transmit station ID Voice commands BDR Select Baud Rate CID Enable Caller ID detection and reporting format CLS Select Data Fax or Voice Audio MDL Identify Model MFR Identify Manufacturer REV TL Identify Revision Level Audio output transmit level VBQ VBS Query Buffer Size Bits per sample ADPCM or PCM
65. iques durant un orage Les prises t l phoniques ne doivent pas tre install es dans des endroits humides except si le mod le a t con u cet effet Ne touchez jamais un cordon t l phonique ou un terminal non isol avant que la ligne ait t d connect e du r seau t l phonique e Soyez toujours prudent lorsque vous proc dez l installation ou la modification de lignes t l phoniques Si vous devez t l phoner pendant un orage pour viter tout risque de choc lectrique utilisez toujours un t l phone sans fil En cas de fuite de gaz n utilisez jamais un t l phone situ proximit de la fuite Laser compliance statement Some IBM Personal Computer models are equipped from the factory with a CD ROM drive or a DVD ROM drive CD ROM drives and DVD ROM drives are also sold separately as options CD ROM drives and DVD ROM drives are laser products These drives are certified in the U S to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations DHHS 21 CFR Subchapter J for Class 1 laser products Elsewhere these drives are certified to conform to the requirements of the International Electrotechnical Commission IEC 825 and CENELEC EN 60 825 for Class 1 laser products When a CD ROM drive or a DVD ROM drive is installed note the following handling instructions CAUTION Use of controls or adjustments or performance of procedures other t
66. itive devices on page 13 before removing the cover To remove the cover 1 Shut down your operating system remove any media diskettes CDs or tapes from the drives and turn off all attached devices and the computer 2 Unplug all power cords from electrical outlets 3 Disconnect all cables attached to the computer This includes power cords input output I O cables and any other cables that are connected to the computer 4 Press the buttons on the sides of the computer and pivot the rear end of the cover up toward the front of the computer Chapter 2 Types 8303 8304 and 8312 17 Locating components The following illustration will help you locate the various components in your computer Power supply H DIMM A PCI slot El Hard disk drive AGP slot some models CD ROM drive or DVD ROM drive El Support bar El Diskette drive Identifying parts on the system board The system board sometimes called the planar or motherboard is the main circuit board in your computer It provides basic computer functions and supports a variety of devices that are IBM installed or that you can install later 18 User Guide The following illustration shows the locations of parts on the system board i i l
67. ive keyboard or mouse e Unattended start mode e Diskette and hard disk I O control Serial and parallel port I O control Security profile by device IBM preinstalled software Your computer might come with preinstalled software If it does an operating system device drivers to support built in features and other support programs are included Operating systems preinstalled varies by model type Note Not all countries or regions will have these operating systems e Microsoft Windows XP Home e Microsoft Windows XP Professional e Microsoft Windows 2000 Professional Operating systems tested for compatibility e Microsoft Windows NT Workstation Version 4 0 e Microsoft Windows 98 Second Edition e 05 27 4 The operating systems listed here are being tested for compatibility at the time this publication goes to press Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet Corrections and additions to this list are subject to change To determine if an operating system has been tested for compatibility check the Web site of the operating system vendor Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 55 Specifications This section lists the physical specifications for your computer Dimensions Height 413 mm 16 25 in Width 191 mm 7 5 in Depth 406 mm 16 in Weight Minimum configuration as shipped 9 1 kg 20 Ib
68. l expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the package and your body When possible remove the option and install it directly in the computer without setting the option down When this is not possible place the static protective package that the option came in on a smooth level surface and place the option on it Do not place the option on the computer cover or other metal surface Installing external options 58 This section shows the various external connectors on your computer to which you can attach external options such as external speakers a printer or a scanner For some external options you must install additional software in addition to making the physical connection When adding an external option use the information in this section to identify the required connector and then use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option Locating the connectors on the front of your computer User Guide The following illustration shows the locations of the connectors on the front of the computer Note Not all computer models will have the following connectors IEEE 1394 connector El USB connector H Microphone connector E USB connector Headphone connector Locating the connectors on the rear of your computer The follow
69. measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute ANSI 12 10 and ISO 7779 and are reported in accordance with ISO 9296 Actual sound pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources The declared sound power levels indicate an upper limit below which a large number of computers will operate Note See the Quick Reference for the classification of your computer 34 User Guide Available options The following are some available options e External options Parallel port devices such as printers and external drives Serial port devices such as external modems and digital cameras Audio devices such as external speakers for the sound system USB devices such as printers joysticks and scanners Security device such as a rope clip Monitors Internal options System memory called dual inline memory modules DIMMs Peripheral component interconnect PCI adapters Accelerated graphics port AGP adapters Internal drives such as CD drive or DVD drive some models Hard disk drive Diskette drives and other removable media drives For the latest information about available options see the following World Wide Web pages e http www ibm com pc us options e http www ibm com pc support You can also obtain informat
70. modem commands The following section lists commands for manually programming your modem Commands are accepted by the modem while it is in Command Mode Your modem is automatically in Command Mode until you dial a number and establish a connection Commands may be sent to your modem from a PC running communication software or any other terminal devices All commands sent to the modem must begin with AT and end with ENTER All commands may be typed in either upper or lower case but not mixed To make the command line more readable spaces may be inserted between commands If you omit a parameter from a command that requires one it is just like specifying a parameter of 0 Example ATH ENTER Basic AT commands In the following listings all default settings are printed in bold text Command Function A Manually answer incoming call Al Repeat last command executed Do not precede A with AT or follow with ENTER D_ 0 9 A D and last number redial pulse dialing Note Pulse dialling is not supported for Australia New Zealand Norway and South Africa T touch tone dialing W wait for second dial tone pause wait for five seconds of silence flash 3 return to Command Mode after dialing DS n Dial one of the four telephone numbers n 0 3 stored in the modem non volatile memory E EO Commands are not echoed E1 Commands are echoed Escap
71. mputer Turn on your computer and look for the following prompt on the logo screen To interrupt normal startup press Enter Press Enter when you see the prompt When the Startup Interrupt Menu displays press F12 Select the desired startup device from the Startup Device menu and press Enter to begin Note Selecting a startup device from the Startup Device menu does not permanently change the startup sequence Changing the startup sequence To view or change the primary or automatic power on startup sequence do the following 1 5 Start the IBM Setup Utility program see Starting the IBM Setup Utilit Select Startup Select Startup Sequence See the information displayed on the right side of the screen Select the sequence of devices for the Primary Startup Sequence the Automatic Startup Sequence and the Error Startup Sequence Select Exit from the IBM Setup Utility menu and then Save Settings If you have changed these settings and want to return to the default settings select Load Default Settings on the Exit menu Chapter 5 Using the IBM Setup Utility program 79 80 User Guide Appendix A Updating system programs This appendix contains information about updating system programs and how to recover from a POST BIOS update failure System programs System programs are the basic layer of software that is built into your computer They include the power on self test POST the basic input output sys
72. n your desktop provides a link to more information about your computer If you have Internet access the most up to date manuals for your computer are available from the World Wide Web To access this information point your browser to http www ibm com pc support Type your machine type and model number in the Quick Path field and click Go Copyright IBM Corp 2002 ix Identifying your computer See Chapter 1 Types 8301 and 8302 See Chapter 2 Types 8303 8304 andl 8312 on page 9 See Chapter 3 Types 8305 8306 8309 and 8313 on page 31 TE See Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 on X User Guide Chapter 1 Types 8301 and 8302 This chapter provides an introduction to the features that are available for your computer m Important Before you install or remove any option read Safety Information on page v These precautions and guidelines will help you work safely Features This section provides an overview of the computer features and preinstalled software Microprocessor Intel Pentium 4 processor with 512 KB of internal L2 cache memory and Intel NetBurst micro architecture Memory Support for two dual inline memory modules DIMMs e 512 KB flash memory for system programs Internal drives Internal hard disk drive Note The hard disk drive should only be removed for ma
73. nnector Audio line in connector Audio line out connector Microphone connector USB connectors Keyboard connector Description Used to attach an external modem serial printer or other devices that use a 9 pin serial connector Used to attach a mouse trackball or other pointing device that uses a standard mouse connector Used to attach a parallel printer parallel scanner or other devices that use a 25 pin parallel connector Used to attach an Ethernet cable for a local area network LAN Note To operate the computer within FCC Class B limits use a Category 5 Ethernet cable Used to receive audio signals from an external audio device such as a stereo system When you attach an external audio device a cable is connected between the audio line out connector of the device and the audio line in connector of the computer Used to send audio signals from the computer to external devices such as powered stereo speakers speakers with built in amplifiers headphones multimedia keyboards or the audio line in connector on a stereo system or other external recording device Used to attach a microphone to your computer when you want to record voice or other sounds on the hard disk if you use speech recognition software Used to attach a device that requires a Universal Serial Bus USB connection such as a USB scanner or USB printer If you have more than four USB devices you can purchase a USB hub which you can
74. ns therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication IBM may make improvements and or changes in the product s and or the program s described in this publication at any time without notice IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk Television output notice The following notice applies to models that have the factory installed television output feature This product incorporates copyright protection technology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macrovision Corporation and is Copyright IBM Corp 2002 97 intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited
75. omputer If it is on already you must turn it off and back on again The update begins Updating flashing BIOS from your operating system Note Due to constant improvements being made to the IBM Web site Web page content including the links referenced in the following procedure is subject to change 1 From your browser type http www pc ibm com support in the address field and press Enter Click NetVista and NetVista Thin Client Click NetVista Personal Computer Click Downloadable files Under Select your product choose your machine type and click Go In Downloadable file by category click BIOS Under Download files BIOS by date click your machine type Scroll down and look for a txt file that has instructions for Flash BIOS update from the operating system Click the txt file one a pP ON Copyright IBM Corp 2002 81 10 Print these instructions This is very important since they are not on the screen after the download begins From your browser Click Back to return to the list of files Carefully follow the printed instructions to download extract and install the update Recovering from a POST BIOS update failure 82 User Guide If power to your computer is interrupted while POST BIOS is being updated flash update your computer might not restart correctly If this happens perform the following procedure to recover 1 10 11 12 13 14 15 16 Turn off the computer and
76. on LAN feature System management features Remote Program Load RPL and Dynamic Host Configuration Protocol DHCP Wake on LAN Wake on Ring in the IBM Setup Utility program this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem Remote Administration Automatic power on startup System Management SM BIOS and SM software Ability to store POST hardware test results Input output features e 25 pin Extended Capabilities Port ECP Extended Parallel Port EPP e Two 9 pin serial connectors Six 4 pin USB connectors PS 2 mouse connector e PS 2 keyboard connector e Ethernet connector e VGA monitor connector Three audio connectors line in line out and microphone Expansion Four drive bays Three 32 bit peripheral component interconnect PCI adapter slots One accelerated graphics port AGP expansion slot Power e 185 W power supply with manual voltage selection switch Automatic 50 60 Hz input frequency switching Advanced Power Management support Advanced Configuration and Power Interface ACPI support Security features User and administrator passwords Support for the addition of a rope clip and lockable cable Support for the addition of an integrated cable lock Startup sequence control Startup without diskette drive keyboard or mouse Unattended start mode Diskette and hard disk
77. ose m What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 51 Installing adapters This section provides information and instructions for installing and removing adapters Your computer has three expansion slots for PCI adapters and one slot used for an AGP adapter You can install an adapter up to 340 mm 13 4 inches long To install an adapter 1 Remove the cover See Removing the cover on page 39 42 User Guide 2 Remove the adapter slot cover latch and the slot cover for the appropriate expansion slot 3 Remove the adapter from its static protective package 4 Install the adapter into the appropriate slot on the system board 5 Install the adapter slot cover latch Tr What to do next e To work with another option go to the appropriate section To complete the installation go to Replacing the cover and connecting the cables on page 51 Chapter 3 Types 8305 8306 8309 and 8313 43 Installing internal drives This section provides information and instructions for installing and removing internal drives Internal drives are devices that your computer uses to read and store data You can add drives to your computer to increase storage capacity and to enable your computer to read other types o
78. output I O 93 input output I O 91 system memory 91 audio line in connector 8 16 38 60 audio line out connector 8 16 38 60 audio subsystem 1 9 31 54 C cables connecting 28 51 74 changing the battery Types 8303 8304 and 8312 27 Types 8305 8306 8309 and 8313 49 Types 8307 8308 8310 8311 8314 and 8315 73 channel assignments DMA 95 IRQ 95 commands Basic AT 83 Extended AT 85 Fax Class 1 87 Fax Class 2 87 MNP V 42 V 42bis V 44 86 Voice 88 connector description Types 8301 and 8302 8 Types 8303 8304 and 8312 16 Types 8305 8306 8309 and 8313 38 Types 8307 8308 8310 8311 8314 and 8315 60 cover removing Types 8303 8304 and 8312 17 Types 8305 8306 8309 and 8313 39 Types 8307 8308 8310 8311 8314 and 8315 61 replacing Types 8303 8304 and 8312 28 Types 8305 8306 8309 and 8313 51 Types 8307 8308 8310 8311 8314 and 8315 74 D device drivers 16 38 60 DIMMs installing 19 41 64 DMA channel assignments 95 DMA I O address map 93 drives bays 2 10 23 32 44 54 67 CD 5 13 35 57 diskette 13 35 57 DVD 13 35 57 Copyright IBM Corp 2002 drives continued hard disk 5 13 35 57 installing 24 45 68 internal 1 9 23 31 44 53 67 removable media 13 35 57 specifications 23 44 67 E environment operating 4 12 34 56 Ethernet connector 8 16 38 60 IBM Setup Utility 77 input output I O address map 91 features 2 10 32 54 installing option
79. pes 8307 8308 8310 8311 8314 and 8315 67 The following illustration shows the locations of the drive bays The following list describes some of the drives you can install in each bay and their height requirements Bay 1 Maximum height 43 0 mm 1 7 in H Bay 2 Maximum height 43 0 mm 1 7 in Bay 3 Maximum height 25 8 mm 1 0 in E Bay 4 Maximum height 25 8 mm 1 0 in H Bay 5 Maximum height 25 8 mm 1 0 in Notes CD drive or DVD drive preinstalled in some models 5 25 inch hard disk drive 5 25 inch hard disk drive 3 5 inch hard disk drive requires a mounting bracket CD drive DVD drive 3 5 inch hard disk drive 3 5 inch diskette drive preinstalled Hard disk drive preinstalled 1 Drives that are greater than 43 0 mm 1 7 in high cannot be installed 2 Install removable media tape or CD drives in the accessible bays bay 1 or 2 Installing a drive To install an internal drive follow these steps 1 Remove the cover See Removing the cover on page 61 2 If your computer has a CD drive or DVD drive you might need to remove the 68 User Guide signal and power cables from the drive 3 Remove the bay panel from the drive bay by inserting a flat blade screwdriver at the end and gently prying it loose 4 Remove the metal shield from the drive bay by inserting a flat blade screwdriver into one of the slots and gently prying it loose 5 Make sure the
80. puter 2 Unplug all power cords from electrical outlets 3 Disconnect all cables attached to the computer This includes power cords input output I O cables and any other cables that are connected to the computer 4 Press the buttons on the sides of the computer and pivot the rear end of the cover up toward the front of the computer 70008 7008 Chapter 3 Types 8305 8306 8309 and 8313 39 Locating components The following illustration will help you locate the various components in your computer CD drive or DVD drive Battery A USB connector E DIMMs USB connector E Microprocessor and heat sink El Optional drive bay AGP slot some models H Hard disk drive PCI slots J Diskette drive Identifying parts on the system board The system board sometimes called the planar or motherboard is the main circuit board in your computer It provides basic computer functions and supports a variety of devices that are IBM installed or that you can install later 40 User Guide The following illustration shows the locations of parts on the system board i i l m Od
81. puter functions and supports a variety of devices that are IBM installed or that you can install later Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 63 The following illustration shows the locations of parts on the system board ji dm f i o 16 m Ca 15 Fa 13 a Microprocessor A DIMM connector 1 DIMM connector 2 E Power connector E Diskette drive connector f Primary IDE connector Front panel connector E Secondary IDE connector EI Battery Clear CMOS Recovery jumper SCSI LED connector PCI slots Front panel audio connector CD ROM audio connector AGP slot some models Serial connector Installing memory 64 User Guide Your computer has two connectors for installing dual inline memory modules DIMMs that provide up to a maximum of 2 0 GB of system memory When installing DIMMs the following rules apply Fill each system memory connector sequentially starting at DIMM connector 1 Use 2 5 V 184 pin 266 MHz double data rate synchronous dynamic random access memory DDR SDRAM Use 128 MB 256 MB 512 MB or 1 GB when available DIMM
82. r computer has extra power connectors for additional drives Connect a power connector to the drive 5 If you have a CD ROM audio cable connect it to the drive and to the system board See Identifying parts on the system board on page 63 Connecting an additional IDE CD drive or DVD drive 1 Locate the secondary IDE connector on the system board and the Te e annedir signal cable Geel Identifying parkson the system baat Gal 2 Connect the extra connector in the signal cable to the new CD drive or DVD drive 3 Your computer has extra power connectors for additional drives Connect a power connector to the drive Connecting an additional IDE hard disk drive 1 Locate the primary IDE connector on the system board One end of the three connector cable connects to the hard disk drive and the other connects to the system board See Identifying parts on the system board on page 63 2 Connect the extra connector in the signal cable to the new hard disk drive 3 Your computer has extra power connectors for additional drives Connect a power connector to the drive Tr What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 74 Installing a rope clip To help prevent hardware theft you can add a 3 16 inch or 5 mm rope clip and cable to your computer After you add the security cable mak
83. r on the system board See Identifying parts on the system board on page 18 Cc Connect one end of the signal cable to the secondary IDE connector on the system board and the other to the CD ROM drive or DVD ROM drive Your computer has extra power connectors for connecting additional drives Connect the power cable to the drive Mm 8 Clear any cables that might impede replacement of the drive cage 9 Pivot the drive cage back into place r What to do next To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 28 Installing a rope clip To help prevent hardware theft you can add a 3 16 inch or 5 mm rope clip and cable to your computer After you add the security cable make sure that it does not interfere with other cables that are connected to the computer For more information about security see Installing a cable lock in Access IBM To install a rope clip 1 Remove the cover see Removing the cover on page 17 Chapter 2 Types 8303 8304 and 8312 25 2 Use a tool such as a screwdriver to remove the two metal knockouts 3 Press both sides of the air baffle and lift it outward from the computer to remove 4 Insert the rope clip through the rear panel then attach and tighten the nuts with an appropriately sized or adjustable wrench 5 Replace the computer cover For
84. ration as shipped 8 1 kg 18 Ib Maximum configuration 9 1 kg 20 Ib Environment Air temperature System on 10 to 35 C 50 to 95 F System off 10 to 43 C 50 to 110 F Maximum altitude 2134 m 7000 ft Note The maximum altitude 2134 m 7000 ft is the maximum altitude at which the specified air temperatures apply At higher altitudes the maximum air temperatures are lower than those specified Humidity System on 8 to 80 System off 8 to 80 Electrical input Input voltage Low range Minimum 90 V ac Maximum 137 V ac Input frequency range 57 63 Hz Voltage switch setting 115 V ac High range Minimum 180 V ac Maximum 265 V ac Input frequency range 47 53 Hz Voltage switch setting 230 V ac Input kilovolt amperes kVA approximate Minimum configuration as shipped 0 08 kVA Maximum configuration 0 30 kVA Note Power consumption and heat output vary depending on the number and type of optional features installed and the power management optional features in use Heat output approximate in British thermal units Btu per hour Minimum configuration 257 Btu hr 75 watts Maximum configuration 497 Btu hr 145 watts Airflow Approximately 0 40 cubic meters per minute 14 cubic feet per minute maximum Acoustical noise emission values Average sound pressure levels At operator position Idle 34 dBA Operating 36 dBA At bystander position 1 meter 3 3 ft Idle 31 dBA Operating
85. rld Wide Web pages e http www ibm com pc us options e http www ibm com pc support You can also obtain information by calling the following telephone numbers Within the United States call 1 800 IBM 2YOU 1 800 426 2968 your IBM reseller or IBM marketing representative e Within Canada call 1 800 565 3344 or 1 800 IBM 4YOU Outside the United States and Canada contact your IBM reseller or IBM marketing representative Tools required To install some options in your computer you might need a flat blade or Phillips screwdriver Additional tools might be needed for certain options See the instructions that come with the option Handling static sensitive devices Static electricity although harmless to you can seriously damage computer components and options When you add an option do not open the static protective package containing the option until you are instructed to do so When you handle options and other computer components take these precautions to avoid static electricity damage Limit your movement Movement can cause static electricity to build up around you Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 57 Always handle components carefully Handle adapters and memory modules by the edges Never touch any exposed circuitry Prevent others from touching components When you install a new option touch the static protective package containing the option to a meta
86. rnal options Locating the connectors on the front of your computer Locating the connec on Ather rear Pat your computer Obtaining device drivers P Removing the cover Locating components Moving the power supply Se Identifying parts on the system hoatd Installing memory Installing adapters Installing internal drives Drive specifications Installing a drive Installing a rope clip Changing the battery Erasing a lost or forgotten password clearing CMOS Replacing the cover and connecting the cables Chapter 5 Using the IBM zur N program Starting the IBM Setup Utility program Viewing and changing settings Exiting from the IBM Setup i program Using passwords User password Administrator password 36 38 38 39 40 41 41 42 44 45 45 48 49 50 01 53 58 56 57 57 3 BF 58 58 60 60 61 62 62 64 64 65 67 68 68 s ZL 73 74 74 77 77 edd 527 77 78 78 iii Setting changing and deleting a password Using Security Profile by Device Selecting a startup device R Selecting a temporary startup device Changing the startup sequence Appendix A SPT pagi programs System programs Updating flashing BIOS rom a a diskette Updating flashing BIOS from your PEE system Recovering from a POST BIOS update failure Appendix B Manual modem commands Basic AT comm
87. s Types 8303 8304 and 8312 adapters 20 DIMMs 19 internal drives 24 memory 19 rope clip 25 Types 8305 8306 8309 and 8313 adapters 42 DIMMs 41 internal drives 45 memory 41 rope clip 48 Types 8307 8308 8310 8311 8314 and 8315 adapters 65 DIMMs 64 internal drives 68 memory 64 rope clip 71 interrupt request IRQ channel assignments 95 K keyboard connector 8 16 38 60 L locating components Types 8303 8304 and 8312 18 Types 8305 8306 8309 and 8313 40 Types 8307 8308 8310 8311 8314 and 8315 62 M memory dual inline memory modules DIMMs 19 41 64 installing 19 41 64 map 91 system 19 41 64 microphone connector 8 16 38 60 101 modem Basic AT commands 83 Extended AT commands 85 Fax Class 1 commands 87 Fax Class 2 commands 87 MNP V 42 V 42bis V 44 commands 86 Voice commands 88 mouse connector 8 16 38 60 moving the power supply 62 N noise level 4 12 34 56 O options available 5 13 35 57 external 5 13 35 57 internal 5 13 35 57 P parallel connector 8 16 38 60 password erasing 28 50 74 lost or forgotten 28 50 74 setting changing deleting 78 physical specifications Types 8301 and 8302 4 Types 8303 8304 and 8312 12 Types 8305 8306 8309 and 8313 34 Types 8307 8308 8310 8311 8314 and 8315 56 power Advanced Configuration and Power Interface ACPI support 2 10 32 54 Advanced Power Management support 2 10 32 54 R recovering from
88. s in any combination e DIMMs are 38 1 mm 1 5 inches in height Note Only DDR SDRAM DIMMs can be used To install a DIMM 1 Remove the cover See Removing the cover on page 61 2 You might have to remove an adapter to gain access to the DIMM slots See Installing adapters 3 To locate the DIMM connectors See Identifying parts on the system board on page 63 4 Open the retaining clips ha 5 Make sure the notches in the DIMM align with the tabs on the connector Push or insert the DIMM straight down into the connector until the retaining clips close m What to do next e Replace any adapters that were removed e Replace the power supply e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting the cables on page 74 Installing adapters This section provides information and instructions for installing and removing adapters Your computer has three expansion slots for PCI adapters and one slot used for an AGP adapter You can install an adapter up to 228 mm 9 inches long To install an adapter 1 Remove the cover See Removing the cover on page 61 Chapter 4 Types 8307 8308 8310 8311 8314 and 8315 65 2 Remove the adapter slot cover latch and the slot cover for the appropriate expansion slot 3 Remove the adapter from its
89. scade channel 5 16 bits Open 6 16 bits Open 7 16 bits Open Copyright IBM Corp 2002 95 96 User Guide Appendix E Notices IBM may not offer the products services or features discussed in this document in all countries Consult your local IBM representative for information on the products and services currently available in your area Any reference to an IBM product program or service is not intended to state or imply that only that IBM product program or service may be used Any functionally equivalent product program or service that does not infringe any IBM intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any non IBM product program or service IBM may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to IBM Director of Licensing IBM Corporation North Castle Drive Armonk NY 10504 1785 U S A INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactio
90. t amp T3 Perform Local Digital Loopback Test amp T4 Grant Remote Digital Loopback Test request by remote modem amp T5 Deny Remote Digital Loopback Test request amp T6 Perform a Remote Digital Loopback Test amp T7 Perform a Remote Digital Loopback Test and Self Test amp T8 Perform Local Analog Loopback Test and Self Test amp V amp VO Displays Active and Stored Profiles Appendix B Manual modem commands 85 Command Function amp V1 Display Last Connection Statistics amp W_ amp WO Stores the active profile as Profile 0 amp W1 Stores the active profile as Profile 1 E_ E0 Disable auto retrain E1 Enable auto retrain MS MS Displays the current Select Modulation settings Displays a list of supported Select Modulation options MS a b c e f Select modulation where a 0 1 2 3 9 10 11 12 56 64 69 b 0 1 c 300 56000 d 300 56000 e 0 1 and f 0 1 A b c d e f default 12 1 300 56000 0 0 Parameter a specifies the modulation protocol desired where 0 V 21 1 V 22 2 V 22bis 3 V 23 9 V 32 10 V 32bis 11 V 34 12 V 90 K56Flex V 34 56 K 56Flex V 90 V 34 64 Bell 103 and 69 Bell 212 Parameter b specifies automode operations where 0 automode disabled 1 automode enabled with V 8 V 32 Annex A Parameter c specifies the minimum connection data rate 300 56000 Parameter d specifies the maximum connection rate 300 56000
91. t for the addition of an integrated cable lock Startup sequence control Startup without keyboard or mouse Unattended start mode Serial and parallel port I O control Security profile by device IBM preinstalled software Your computer might come with preinstalled software If it does an operating system device drivers to support built in features and other support programs are included Operating systems preinstalled varies by model type Note Not all countries or regions will have these operating systems e Microsoft Windows XP Home e Microsoft Windows XP Professional e Microsoft Windows 2000 Professional Operating systems tested for compatibility e Microsoft Windows NT Workstation Version 4 0 e Microsoft Windows 98 Second Edition OS 2 1 The operating systems listed here are being tested for compatibility at the time this publication goes to press Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet Corrections and additions to this list are subject to change To determine if an operating system has been tested for compatibility check the Web site of the operating system vendor Chapter 1 Types 8301 and 8302 3 Specifications This section lists the physical specifications for your computer Dimensions Height 110 mm 4 3 in Width 310 mm 12 2 in Depth 343 mm 13 5 in Weight Minimum configu
92. tem BIOS code and the IBM Setup Utility program POST is a set of tests and procedures that is performed each time you turn on your computer BIOS is a layer of software that translates instructions from other layers of software into electrical signals that the computer hardware can understand You can use the IBM Setup Utility program to view and change the configuration and setup of your computer Your computer system board has a module called electrically erasable programmable read only memory EEPROM also referred to as flash memory You can easily update POST BIOS and the IBM Setup Utility program by starting your computer using a flash update diskette or by running a special update program from your operating system IBM might make changes and enhancements to the system programs When updates are released they are available as downloadable files on the World Wide Web see the Quick Reference Instructions for using the system program updates are available in a txt file that is included with the update files For most models you can download either an update program to create a system program update flash diskette or an update program that can be run from the operating system Updating flashing BIOS from a diskette 1 Insert a system program update flash diskette into the diskette drive drive A in your computer System program updates are available at http www ibm com pc support on the World Wide Web 2 Turn on the c
93. ter The following illustration shows the locations of the connectors on the rear of the computer o A El Oo A none CL 1 ar lol i Qo E Ti OET ETTI Jo S ONS CET Cu Serial connector E Audio line out connector A Mouse connector Microphone connector Parallel connector USB connectors El Ethernet connector VGA monitor connector H Audio line in connector Serial connector J Power connector USB connectors PCI slots Keyboard connector EJ AGP slot some models Note Some connectors on the rear of the computer are color coded to help you to determine where to connect the cables on your computer Chapter 2 Types 8303 8304 and 8312 15 Connector Serial connector Mouse connector Parallel connector Ethernet connector Audio line in connector Audio line out connector Microphone connector USB connectors Keyboard connector Description Used to attach an external modem serial printer or other devices that use a 9 pin serial connector Used to attach a mouse trackball or other pointing device that uses a standard mouse connector Used to attach a parallel printer parallel scanner or other devices that use a 25 pin parallel connector Used to attach an Ethernet ca
94. the maintenance or configure position pins 2 and 3 Replace the cover and connect the power cord See Replacing the cover and connecting the cables on page 51 Restart the computer leave it on for approximately 10 seconds Turn off the computer by holding the power switch for approximately 5 seconds The computer will turn off Repeat steps 2 through 4 on page 50 Move the jumper back to the standard pins 1 and 2 Replace the cover and connect the power cord See Replacing the cover and connecting the cables on page 51 Replacing the cover and connecting the cables After working with options you need to install any removed parts replace the cover and reconnect any cables including telephone lines and power cords Also depending on the option that is installed you might need to confirm the updated information in the IBM Setup Utility program To replace the cover and connect cables to your computer 1 Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer 2 Clear any cables that might impede the replacement of the cover 3 Position the cover over the chassis and pivot it down over the computer until it snaps into place 4 Reconnect the external cables and power cords to the computer See Installing external options on page 36 5 To date the 7 see Chapter 5 Using the IBM Setup Utility program on page 77
95. the information displayed on the right side of the screen Using Security Profile by Device 78 User Guide Security Profile by Device is used to enable or disable user access to the following devices IDE controller When this feature is set to Disable all devices connected to the IDE controller such as hard disk drives or the CD ROM drive are disabled and will not be displayed in the system configuration Diskette Drive Access When this feature is set to Disable the diskette drive cannot be accessed Diskette Write Protect When this feature is set to Enable all diskettes are treated as if they are write protected To set Security Profile by Device do the following 1 Start the IBM Setup Utility program see Starting the IBM Setup Utility program on page 77 ogram on page 77 From the IBM Setup Utility program menu select Security Select Security Profile by Device Select the desired devices and settings and press Enter ak oh Return to the IBM Setup Utility program menu and select Exit and then Save Settings Selecting a startup device If your computer does not start up boot from a device such as the CD ROM diskette or hard disk as expected use one of the following procedures to select a startup device Selecting a temporary startup device Use this procedure to startup from any boot device Note Not all CDs hard disks and diskettes are startable bootable 1 2 Turn off your co
96. until the retaining clips close m What to do next e To work with another option go to the appropriate section e To complete the installation go to Replacing the cover and connecting thel cables on page 28 Installing adapters This section provides information and instructions for installing and removing adapters Your computer has three expansion slots for PCI adapters and one slot used for an AGP adapter Adapters must be low profile Your computer supports adapters up to 168 mm 6 6 inches long To install an adapter 1 Remove the cover See Removing the cover on page 17 20 User Guide 2 Pivot one of the drive bay latch handles toward the front of the computer and then pivot the drive bay cage upward as shown until it is latched in the up position Repeat this procedure for the remaining drive bay Chapter 2 Types 8303 8304 and 8312 21 4 Remove the adapter slot cover latch and the slot cover for the appropriate expansion slot 5 Remove the adapter from its static protective package 6 Install the adapter into the appropriate slot on the system board 7 Install the adapter slot cover latch 8 Clear any cables that might impede the replacement of the drive bays 9 Replace the support bar and pivot the two drive bays back to their original positions M What to do next To work with another option go to the appropri
97. use to connect additional USB devices Used to attach a keyboard that uses a standard keyboard connector Chapter 2 Types 8303 8304 and 8312 This chapter provides an introduction to the features and options that are available for your computer You can expand the capabilities of your computer by adding memory adapters or drives When installing an option use these instructions along with the instructions that come with the option m Important Before you install or remove any option read Safety Information on page v These precautions and guidelines will help you work safely Features This section provides an overview of the computer features and preinstalled software Microprocessor varies by model type Intel Pentium 4 processor with 256 KB or 512 KB of internal L2 cache memory and Intel NetBurst micro architecture Memory Support for two dual inline memory modules DIMMs e 512 KB flash memory for system programs Internal drives e 3 5 inch 1 44 MB diskette drive e Internal hard disk drive e EIDE CD ROM drive or DVD ROM drive some models Video subsystem e Intel Extreme graphics Accelerated graphics port AGP video adapter slot on the system board some models Audio subsystem Integrated SoundMAX 3 audio Copyright IBM Corp 2002 9 10 User Guide Connectivity 10 100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN feature
98. ve requires two cables a four wire power cable that connects to the power supply and a signal cable that connects to the system board y I The steps to connect an IDE drive are different depending on the type of drive you are connecting Use one of the following procedure for your drive connection Connecting the first IDE CD drive or DVD drive 1 Locate the three connector signal cable that comes with your computer or with the new drive 2 Locate the secondary IDE connector on the system board See Identifying parts on the system board on page 40 3 Connect one end of the signal cable to the drive and the other to the secondary IDE connector on the system board To reduce electronic noise use the connectors at the end of the cable only 4 Your computer has extra power connectors for additional drives Connect a power connector to the drive Chapter 3 Types 8305 8306 8309 and 8313 47 5 If you have a CD ROM audio cable connect it to the drive and to the system board See Identifying parts on the system board on page 40 Connecting an additional IDE CD drive or DVD drive 1 Locate the secondary IDE connector on the system board and the three connector signal cable See Identifying parts on the system board on page 40 40 2 Connect the extra connector in the signal cable to the new CD drive or DVD drive 3 Your computer has extra power connectors for additional drives Connect a power connector
99. x syst mes de t lecommunication et aux modems sauf instruction contraire mentionn e dans les proc dures d installation et de configuration Lorsque vous installez que vous d placez ou que vous manipulez le pr sent produit ou des p riph riques qui lui sont raccord s reportez vous aux instructions ci dessous pour connecter et d connecter les diff rents cordons Connexion D connexion 1 Mettez les unit s hors tension 1 Mettez les unit s hors tension 2 Commencez par brancher tous les 2 D branchez les cordons d alimentation cordons sur les unit s des prises 3 Branchez les c bles d interface sur des 3 D branchez les c bles d interface des connecteurs connecteurs 4 Branchez les cordons d alimentation sur 4 Debranchez tous les c bles des unit s des prises 5 Mettez les unit s sous tension Lithium battery notice CAUTION Danger of explosion if battery is incorrectly replaced When replacing the battery use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer The battery contains lithium and can explode if not properly used handled or disposed of Do not e Throw or immerse into water e Heat to more than 100 C 212 F Repair or disassemble Dispose of the battery as required by local ordinances or regulations ATTENTION Danger d explosion en cas de remplacement incorrect de la batterie Remplacer uniquement par une batterie
100. xposed circuitry Prevent others from touching components When you install a new option touch the static protective package containing the option to a metal expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the package and your body When possible remove the option and install it directly in the computer without setting the option down When this is not possible place the static protective package that the option came in on a smooth level surface and place the option on it Do not place the option on the computer cover or other metal surface Installing external options This section shows the various external connectors on your computer to which you can attach external options such as external speakers a printer or a scanner For some external options you must install additional software in addition to making the physical connection When adding an external option use the information in this section to identify the required connector and then use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option Locating the connectors on the front of your computer 14 User Guide The following illustration shows the locations of the connectors on the front of the computer USB connector A USB connector Locating the connectors on the rear of your compu
101. y for your computer and data There are two kinds of passwords a user password and an administrator password You do not have to set a password of either type to use your computer However if you decide to set either one read the following sections Copyright IBM Corp 2002 77 User password The user password feature deters unauthorized persons from gaining access to your computer Administrator password Setting an administrator password deters unauthorized persons from changing configuration settings If you are responsible for maintaining the settings of several computers you might want to set an administrator password After you set an administrator password a password prompt is displayed each time you try to access the IBM Setup Utility program If you type the wrong password you will see an error message If you type the wrong password three times you must turn the computer off and start again If both the user and administrator passwords are set you can type either password However to change any configuration settings you must use your administrator password Setting changing and deleting a password To set change or delete a password do the following Note A password can be any combination of up to seven characters A Z a z and 0 9 1 Start the IBM Setup Utility program see Starting the IBM Setup Utili 2 From the IBM Setup Utility program menu select Security 3 Select Set Passwords Read
102. ystem management features Remote Program Load RPL and Dynamic Host Configuration Protocol DHCP e Wake on LAN Wake on Ring in the IBM Setup Utility program this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem Remote Administration Automatic power on startup System Management SM BIOS and SM software Ability to store POST hardware test results Input output features e 25 pin Extended Capabilities Port ECP Extended Parallel Port EPP e Two 9 pin serial connectors Six 4 pin USB connectors PS 2 mouse connector e PS 2 keyboard connector e Ethernet connector e VGA monitor connector Three audio connectors line in line out and microphone JEEE 1394 connector some models Front connectors for microphone and headphone some models Expansion e Five drive bays e Three 32 bit peripheral component interconnect PCI adapter slots e One accelerated graphics port AGP expansion slot Power e 185 W power supply with manual voltage selection switch Automatic 50 60 Hz input frequency switching Advanced Power Management support Advanced Configuration and Power Interface ACPI support Security features User and administrator passwords Support for the addition of a rope clip and lockable cable Support for the addition of an integrated cable lock Startup sequence control Startup without diskette dr

Download Pdf Manuals

Related Search

Related Contents

Istruzioni d’uso  User instructions  smokemeter dx260 dx270 manual  Black & Decker LDX220SBFCR User's Manual  Replacement Manual  446s CHAIN SAW 452s CHAIN SAW  Manual English  SAVE NET 取扱説明書    manual  

Copyright © All rights reserved. Failed to retrieve file