www.mortuary.spencer.it Folding dressing table with adjustable
Contents
1. Are all spare parts included in the box Before transporting the device carry out the following checks the packaging is safe and adequate risk of bumping or falling during the transportation is minimised Keep the original packaging for any future transportation Any damages during the transportation and loading unloading operations are not covered by the warranty Any repai ring or replacement of damaged parts is at the Customer s charge The product should be stocked in a dry humidity free place In case of damages to the box or any other packaging material immediately call the forwarder and afterwards con tact Spencer Italia S r l If the product shows any defects or damages it must be IMMEDIATELY PUT OUT OF USE as long as it is comple tely repaired or replaced 4 2 METHOD OF USE See pages 4 5 4 3 TROUBLE SHOOTING CHART See page 4 MAINTENANCE 5 1 PRESERVATION The product needs periodic maintenance and checks to preserve its efficiency and to extend its life Check the product at least once a month and more frequently if the product is used on a regular basis The check must consist in verifying the correct functioning of the product detecting any anomalies that could compro mise its integrity and correct functioning 5 2 CLEANING The Frack must be cleaned after each use At the same time an inspection must be carried out to check the product for damages Disinfect the Frack with a clean cloth2. using an alcohol free detergent Never use aggressive substances or solvents of any kind If necessary dry with a clean clothe eS A Whilst stocking do not place heavy loads onto the Frack the product must never be considered as a stora ge platform for any materials 5 3 CUSTOMER SERVICE For any information concerning the use maintenance installation the Manufacturer is at the Customer s disposal 5 4 DEMOLITION Keep to laws in force 5 5 ENVIRONMENTAL CONDITIONS Acceptable conditions for working preservation and transportation TEMPERATURE OF USE from 10 to 50 C TEMPERATURE OF PRESERVATION AND TRANSPORTATION from 20 to 60 C 6 J ACCESSORIES AND SPARE PA 6 1 ACCESSORIES AND SPARE PARTS Each product is supplied with a set of restraint belts Mod 591 Code ST00591A DESCRIPTION efe B QUICK ASSEMBLE BASIN for Frack ZV00201A CARRYING BAG for Frack ZV00202A SAFETY BELT Mod 591 ST00591A Notice t The information contained in this document may be modified without notification and therefore it does not represent a formal offer engagement for the Manufacturer Spencer exports its products to many countries where the same rules cannot always be applied For this reason there may be some little differences between what is described here and what is effectively delivered Spencer continuously aims to perfection all of its products We are sure to count on your understanding fo
3. the fabric can contain the liquids F R After ensuring the plug is clo z sed it is possible to use the basin system for Frack A avoid liquid stagnation the Frack should be set to a tilted position and the corpse fixed to the board with the restraint system provided locked into position model with Use the Frack only for the intended purposes i Do not use the Frack if q the brakes on the four wheels are not locked into position model with wheels only With the help of an operator pull the lever on one side of the Frack so to release the leg mechanism Adjust the belt once again and check that all mechani sms are locked into position Use the Frack only for the intended purposes d Before any height adjust ment check the proper adjustment of the safety belt loosen it before the height adjustment then tighten it adequately Press the 2 buttons at the top of the basin then the ones positioned on the sides making sure that at the end of the operation the fabric of the basin forms a corner where the horizontal and vertical levels meet repeat this procedure on all 4 corners of the basin Insert the valve in the trian gular buttonhole and even tually connect a way out hose Copyright Spencer Italia S r l All Rights reserved Rev 2 22 01 08 5
4. FRACK Folding dressing table with adjustable heights FRACK Dressing table with adjustable heights Cod ZV00200A FRACK Dressing table with adjustable heights 4 swivel whells with brakes Cod ZV00204A 4 INDEX GENERAL INFORMATION PRODUCT DESCRIPTION SAFETY OPERATIONS MAINTENANCE ACCESSORIES AND SPARE PARTS Spencer Italia S r l Str Cavi 7 43044 Collecchio PR ITALY tel 39 0521 541111 fax 39 0521 541222 e mail info spencer it SP 01 242 1U Thank you for choosing Mortuary GENERAL INFORMATION i 1 1 CONTENTS AND PURPOSE This manual is intended to provide the customers with all the necessary information to manage the product in the most adequate autonomous and safe way It includes information related to Technical matters Operation Maintenance Spare Parts and Safety 1 2 PRESERVATION OF THE MANUAL The Instruction Manual must be kept near the product in a special container and most importantly away from liquids and anything that may compromise its legibility 1 3 SYMBOLS USED SYMBOL MEANING DANGER Indicates a danger also with risk of death for i users WARNING Indicates a warning note about key functions or useful information Pay maximum attention to text blocks marked by this symbol eS Before each use read the instructions contained in this publication carefully In case of doubts on how to interpret the instructions ask the Manufacturer for the necessary explan
5. ation 2 DESCRIPTION OF TH 2 1 INTENDED USE The adjustable heights folding system for the FRACK dressing table is intended for corpse cleaning preparation and dressing The Frack is easy to use thanks to its small dimensions weight and folding system optimising storage and carrying The FRACK is available with or without swivelling wheels 2 2 MAIN COMPONENTS The product cannot be separated into parts with the exception of the restraint system 2 3 DIMENSIONS AND TECHNICAL DATA Thickness max folded 180 mm Height max folded 980 mm Board max Width 630 mm Length max folded 1860 mm Total weight with wheels 19 5 kg Max Load Cap 150 kg Wheels if present 100 mm swivelling with brake N 3 Adjust heights 550mm 720mm 850 mm Frame Polished aluminium 35 Board One shell high density polyethylene 3 SAFETY E 3 1 GENERAL ADVICE eS The operator must read the information in this Manual carefully especially the parts concerning cautions for safety and methods of use H The product must not undergo manumission or mishandling should this occur we decline any responsibility for any damages caused Ensure to position the belt parallel to the two central joints see figure 9 page 5 In case of anomalies or damages that may compromise the good functioning and the safety of the product it is necessary to put the product immediately out of use Evenly distribute the w
6. eight on the Frack table Always respect the maximum load capacity as indicated in the present User s Manual The FRACK must not be exposed nor come tin contact with flammable agents or thermal sources The Frack can be only used when it is open When folded or in a vertical position and if unlocked the Frack does not provide a steady balance Pay attention When opening or folding the Frack the parts in movement centre of the board leg mechanism can be dangerous for the operator s hands if caught between them Whilst folding make sure that the surface between the 2 tables is absolutely free from any objects or extraneous bodies Whilst stocking do not place heavy loads onto the Frack the product must never be considered as a storage platform for any materials 3 2 LABELLING A OPERATIONAL INSTRUCTIONS The serial number as indicated below can be found on each appliance and must not be removed or covered In order to facilitate assistance please indicate or communicate the serial number SN or lot number LOT on the label 4 1 TRANSPORTATION AND STOCKING l Always make sure of the integrity of Frack before each use so to detect any anomalies or damages When opening the packing and before each use check that the screws are fixed properly Before using the device carry out the following checks Is the product free from cuts abrasions holes deformations Are the adjustable heights comfortable to reach
7. r occasional slight modifications in the shape equipment and technique explained in this manual 4 3 TROUBLE SHOOTING CHART PROBLEM When open the Frack does not stay in a horizontal position CAUSE Something is obstructing the fol ding of the board ACTION Eliminate the obstructing element The surface of the grounds the Frack is positioned on is rough and irregular Always check the grounds before each use The brakes are not locked into posi The open Frack does not have tion Lock the brakes on the four wheels pressing the levers with your foot a steady balance The restraint belt on the lower part of the Frack is not properly adjusted Position the belt on the lower part of the Frack correctly Wear and tear excessive load human The FRACK is damaged error Immediately put the product out of use and contact Customer Service The buttons are not fastened correc tly or the metal inserts are not bent to the right angle The Frack basin leaks Check the sealing of the buttons and angle the metal inserts inwards METHOD OF USE l Take the product out of the box checking the integrity and the presence of all the accessories Pull the red lever towards the board releasing the safety lock m With the help of an opera tor lift the Frack and make it stand on_its legs or wheels if present A Position the closed FRACK on asafe and level
8. surface resting the longer part of it on the ground Open the two tables and the legs until the highest adjustable height is set verify that the pivot comes out from the hole on the telescopic piston Choose the most appropriate height between those available 55 cm 72 cm 85 cm from the ground Lock the restraint belt if it is open which is located underneath the board in corre spondence with the central ledge and adjust it using the apposite regulator as shown in the images Ensure to position the belt paral lel to the two central joints see figure 9 After choosing the height and S where to position the Frack make sure that the brakes on each of the four wheels are locked into position model with wheels only HEIGHT ADJUSTMENT Adjust the safety belt s length using the fastener Once the_right height is found release the lever and make sure that the safety pivot is inserted in the apposite hole on the telescopic tube N gt After choosing the height and where to position the Frack HOW TO USE THE FRACK make sure that the brakes on each of the four wheels are wheels only Put the basin on an open Frack a making it sure that the plug is ree positioned downwards and that ae N the perimeter of the basin fits the tabletop Bend the 8 metal inserts on the fabric edges 3 each on the long sides and 1 each on the short sides manually turning them inwards so that
Download Pdf Manuals
Related Search