Instructions - Fisher
Contents
1. tabs Make sure the tabs fit into the slot in each pedal hub e While holding the pedal hubs on the pedal axle insert the 7 Assembly Front Wheel Pedal Pedal Axle Front Wheel Assembly pedal axle through the hole in the center of the front wheel e Push the pedal hubs into the center of the front wheel until e Place a scrap block of wood under the front wheel assembly with the exposed end up Fit a pedal on the pedal axle Tap the pedal with a hammer until it is secure they are flush with the surface of the front wheel Pedal Axle Fork Arms Fork Cover Pedal Hub 5 Pedal Axle Place the front wheel assembly between the fork arms Make sure the pedal axle fits into the groove at the bottom of each fork arm Turn the front wheel assembly over Insert a pedal hub onto the top of the pedal axle and into the hole in the center of the front wheel Place a fork cover over the pedal axle on one fork arm Insert two 8 x 3 4 1 9 cm screws through the fork cover ay and into the fork arm Tighten the screws with a Phillips Insert the remaining pedal hub below the pedal axle and screwdriver Do not over tighten into the hole in the center of the front wheel Repeat this procedure to attach the other fork cover to the Push the pedal hubs into the center of the front wheel until other fork arm they are flush with the surface of the front wheel e Assembly Q Ay Handleba2. Fisher Price Please keep this instruction sheet for future reference as itcontains important information Adult assembly is required Required tools Hammer Phillips Screwdriver and Scrap Block of Wood not included Age 2 6 years Weight Limit 60 Ibs 27 kg www fisher price com Consumer Information N WARNING TO AVOID SERIOUS INJURY a umy e Continuous adult supervision is required e Never use near cars and other motor vehicles near streets steps sloped Cap Nut 8 x 3 4 1 9 cm Screw 4 driveways hills roadways alleys swimming NNN NON NNN NN NON pools or other bodies of water P i e Always wear shoes Xa ATE CM SEW e Never allow more than one rider FASTENERS SHOWN ACTUAL SIZE Parts e Please save all packaging material until assembly is complete to ensure that no parts are discarded e Please wipe each part with a clean dry cloth before assembly e Some parts shown are assembled to both sides of the trike e Tighten the assembled screws with a Phillips screwdriver Do not over tighten the screws Handlebar Cap 7 Seat St Seat Retainer Straight Axle Fork Rear Wheel 2 Hubcaps 2 Covers Frame Cap Nut _ _S Za 2 Pedals Pedal Axle E Cap Nut Assembly Tool Front Wheel 4 Pedal Hubs Part Not Shown Label Sheet Assembly VAN oF Un ile This product contains small parts in an unassembled state Adult assembly is required Rear Wheel Indented Si
3. de Down lt Hubcap Straight Axle e Slide a hubcap peg side up onto the straight axle e Slide a rear wheel indented side down onto the straight axle Hole Straight Axle 2 BOTTOM VIEW e Turn the frame upside down e Insert the straight axle through the holes in the rear of the frame e e Rear Wheel Indented Side Up a4 lt ___ Cap Nut Straight Axle W_ gt Frame OX XOK 00009 00000 Assembled Rear Wheel gt Cap Nut 3 Assembly Tool Place a scrap block of wood on a flat surface Turn the frame on its side with the exposed end of the straight axle up Place the cap nut assembly tool under the assembled rear wheel and onto the cap nut Slide a rear wheel indented side up onto the end of the straight axle Slide a hubcap peg side down onto the straight axle Place a cap nut on the end of the straight axle Tap the cap nut with a hammer Gently pull the rear wheel up to be sure the cap nut is securely attached to the straight axle Dispose of the cap nut assembly tool properly Insert one of the tabs on a cover into a slot in the hubcap Push to snap the cover in place Repeat this procedure to attach the other cover to the other hubcap Set the frame assembly aside Pedal Hub Pedal Axle Pedal Hub Fit two pedal hubs onto the pedal axle
4. he seat up or down Seat Tabs Seat Retainer Upper Position Middle Position Lower Position e At an angle insert the tabs on the seat into any of the top three sets of slots for the lower middle or upper position e Lower the seat so that the seat retainer inserts and snaps into the slots in the frame e Pull up on the seat to be sure it is secure gi 00000 87 a Seat goody Seat Retainer Tab Ze s Oo oO Oo Frame 0 0 0 0 ON Seat Retainer Tab 0000 e Turn the frame on its side e Squeeze the seat retainer tabs toward one another and lift the seat from the frame Fisher Price Inc a subsidiary of Mattel Inc East Aurora New York 14052 U S A 2011 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc Consumer Information IMPORTANT It is a good practice to start training children very young regarding the importance of helmet use When children are older and riding bicycles and faster vehicles it is important that they use a helmet each and every time they ride For this reason even while riding a tricycle it is a good idea to familiarize your child with helmet use so that it becomes a habit for life Choose a helmet that complies with requirements of the applicable certifying agency for bicycle helmets Care e Periodically check the plastic parts and if broken or cracked dispose of them properly e Check all fasteners regularl
5. r Frame Neck Fork Post 11 e Position the seat upside down ki e Fit the small pegs on the seat retainer into the holes in the seat 9 AAACN Turn the frame upright Insert the fork post up through the hole in the neck of the frame Make sure the fork is positioned so that the fork covers face the rear wheels Place the handlebar over the fork post and push it down onto the frame Make sure the handlebar is positioned so that the screw hole faces the rear wheels and aligns with the screw hole in the fork post Hint You may need to rotate the handlebar to align the holes e Insert the 8 x 3 7 6 cm screw through the hole in the handlebar and into the fork post Tighten the screw with a Phillips screwdriver Do not over tighten Label on other side e Make sure the areas where the labels will be applied are clean and dry Wipe your vehicle with a clean soft dry cloth to remove any dust or oils e For best results avoid applying a label more than once e Apply the labels as shown in the illustration above 10 e Insert and snap the cap into the hole in the frame Attaching and Removing the Seat Helpful Hint The seat can be attached to the frame in any of three positions depending on the size of your child Check your child s fit on the trike by observing the seat to pedal distance as it is being ridden If the pedals seem too far away or too close for your child move t
6. y to be sure they are tight If the fasteners are not tight tighten them as necessary e To clean use a mild soap and water solution and a clean cloth Rinse clean with water to remove soap residue CONSUMER ASSISTANCE 1 800 432 5437 US amp Canada 1300 135 312 Australia service fisher price com Fisher Price Inc 636 Girard Avenue East Aurora NY 14052 Hearing impaired consumers 1 800 382 7470 Outside the United States Canada Mattel Canada Inc 6155 Freemont Blvd Mississauga Ontario L5R 3W2 www service mattel com Great Britain Mattel UK Ltd Vanwall Business Park Maidenhead SL6 4UB Helpline 01628 500303 www service mattel com uk Mattel Europa B V Gondel 1 1186 MJ Amstelveen Nederland Australia Mattel Australia Pty Ltd 658 Church Street Locked Bag 870 Richmond Victoria 3121 Australia New Zealand 16 18 William Pickering Drive Albany 1331 Auckland PRINTED IN MEXICO M7332a 0921
Download Pdf Manuals
Related Search