Vision Scan 575 User Manual
Contents
1. 5 Press the UP button to select ON to activate this function or OFF to deactivate this function 6 Press MODE ENTER to confirm 7 Press EXIT to return to the main menu FINE Switch between 16 bit 8 bit resolution of movement 1 Access the main menu 3 Tap the UP button until FINE is displayed press MODE ENTER 4 The display will show ON OFF 5 Press the UP button to select ON to activate this function or OFF to deactivate this function 6 Press MODE ENTER to confirm 7 Press EXIT to return to the main menu DISP MAIN MENU 7 Press EXIT DN to return to the main menu RPAN MAIN MENU RPAN The movement of the Pan will be reversed 1 Access the main menu 2 Tap the UP button until RPAN is displayed press MODE ENTER 4 The display will show ON OFF 5 Press the UP button to select ON to activate this function or OFF to deactivate this function 6 Press MODE ENTER to confirm 7 Press EXIT to return to the main menu RTILT MAIN MENU RTILT The movement of the Tilt will be reversed 1 Access the main menu 3 Tap the UP button until RTILT is displayed press MODE ENTER 4 The display will show ON OFF 5 Press the UP button to select ON to activate this function or OFF to deactivate this function 6 Press MODE ENTER to confirm 7 Press EXIT to return to the main menu DISP MAIN MENU 7 Press EXIT to retu2. OFF Press the UP button to display ON to activate this function or OFF to deactivate this function Press MODE ENTER to confirm Press EXIT to return to the main menu When you exit this function the unit will begin to reload data NDAN VER Use this function to display the Software version of the unit 1 Access the main menu 2 Tap the UP button until SPEC is displayed press MODE ENTER 3 Tap the UP button until VER is displayed press MODE ENTER 4 The display will show V 1 0 the display may also show V 2 0 V 9 9 etc 5 Press ENTER or EXIT DN to exit EDIT This menu item allows you to write a program into the memory EEPROM via the control panel or via the external controller RUN With the function RUN you can run your pre made program You can set the number of steps under Step S 01 S 48 You can edit the individual scenes under Edit 1 Access the main menu 2 Tap the UP button until EDIT is displayed press MODE ENTER 3 Tap the UP button until RUN is displayed press MODE ENTER 4 AUTO is displayed If you press the UP button it will show SOUN Select which one you want to activate and press ENTER 5 Press UP to select ALON or NAST Which mean stand alone and master slave mode 6 Select a mode and press ENTER to confirm 7 Press EXIT DN to return to the main menu STEP With this function you can
3. program the number of steps in your individual Program 1 Access the main menu 2 Tap the UP button until EDIT is displayed press ENTER 3 Tap the UP button until STEP is displayed press ENTER 4 The display shows S 01 this stands for the first step of your program You can call up to 48 scenes in Run For example if S 05 is displayed it means that Run will run the first 5 scenes you saved in Edit 5 Press ENTER to save and exit SC01 With this function you can choose the number of scenes in your Program 1 Access the main menu 2 Tap the UP button until EDIT is displayed press MODE ENTER 3 Tap the UP button until SC01 is displayed 4 The display shows SC01 this stands for the first scene of your program You can call up to 30 scenes For example if SC05 it means that Run will run the first 5 scenes you saved in Edit 5 Press ENTER to save and exit Editing procedure 1 Using the control board only 1 Access the main menu 2 Tap the UP button until EDIT is displayed Press MODE ENTER 3 The display will show SC 01 this stands for the scene number For example SC 01 is displayed it means you will be editing scene 1 press MODE ENTER You can change the scene number by pressing the UP button 4 Press MODE ENTER the display will show C 1 this stands for the channel number If C 01 is displayed you wi
4. to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current
5. 0 167 Macro 5 168 175 Macro 6 176 183 Macro 7 184 191 Macro 8 192 199 Macro 9 200 207 Macro 10 208 215 Macro 11 216 223 Macro 12 224 231 Macro 13 232 239 Macro 14 240 247 Macro 15 248 255 Macro 16 Channel 10 Focus amp Zoom 0 85 Zoom1 amp Continuous adjustment from far to near 86 171 Zoom2 amp Continuous adjustment from far to near 172 255 Zoom3 amp Continuous adjustment from far to near Channel 11 Shutter strobe 0 31 Shutter closed 32 63 No function shutter open 64 95 Strobe effect slow to fast 96 127 No function shutter open 128 159 Pulse effect in sequences 160 191 No function shutter open 192 223 Random strobe effect slow to fast 224 255 No function shutter open Channel 12 Dimmer intensit 0 255 Intensity 0 to 100 Channel 13 Iris 0 191 Max diameter to Min diameter 192 223 Pulse closing fast to slow 224 255 Pulse opening slow to fast Channel 14 Frost 0 191 Frost 0 100 192 223 Pulse closing fast to slow 224 255 Pulse opening slow to fast Channel 15 Speed pan tilt movement 0 4 max speed 5 225 max to min speed 226 235 blackout by movement 236 245 blackout by all wheel changing 246 255 no function Channel 16 Lamp on off reset internal programs 0 19 colour change normal 20 39 colour change to any position 40 59 Lamp on 60 79 Lamp switch off 80 84 All motor reset 85 87 Scan motor reset 88 90 Colors motor reset 91 93 Gobos motor reset 94 96 Shutter amp Di
6. EST Reset Resets the unit to default VER Version Displays the software version EDIT MENU RUN This will run your own custom program STEP S 01 S 48 These are the steps slots that you write your programs into There are at total of 48 steps SCXX SC01 SC30 These are the scenes that are stored in your program There are a total of 30 scenes C 01 C 08 Channel 1 Channel 08 The channels of each scene that can be edited See page 27 TIME Time Running time of the entire program See page 27 CEDT Edit program using a external controller See page 29 On Board System Menu The Accu Scan 250 comes with an easy to navigate system menu This next section will detail the functions of each command in the system menu Enter Button To access the main menu locate the MODE ENTER button 4 on the front of the unit Press this button to activate the system menu Tap the UP button 2 until you reach function you wish to change When you reach the function you wish to change tap the MODE ENTER button When a function is selected the menu will begin to ash use the UP button to change the function Once your changes are made tap the MODE ENTER button again to lock the change in the system To exit without making any changes tap the EXIT button 2 ADDR MAIN MENU ADDR DMX Address Setting via control board 1 Access the main menu 2 Tap the UP button until ADDR is displayed press ENTER 4 Now the dis
7. Hz 0220VAC 50Hz 0230VAC 50Hz 0240VAC 50Hz 98VAC 60Hz 0120VAC 60Hz 0208VAC 50Hz 0220VAC 60Hz 0230VAC 60Hz 0240V AC 60Hz Power consumption max 01000W Lamp MSR 575 2 6500k Motors 13 micro motors Packing dimensions 92x48x43cm Net weight 032KGS Gross weight 036KGS Remark errors and omissions for every information given in this manual excepted All information is subject to change without prior notice mL Galea
8. NTER 3 Tap the UP button until GOBO is displayed press MODE ENTER to confirm 4 The display will show ON OFF Press the UP button to select ON to reset the gobo motor Press MODE ENTER to confirm 5 Press EXIT DN to return to the main menu SHTR When you activate this reset function the fixture will only reset the shutter dimmer motor 1 Access the main menu 2 Tap the UP button until RESE is displayed press MODE ENTER 3 Tap the UP button until SHTR is displayed press MODE ENTER to confirm 4 The display will show ON OFF Press the UP button to select ON to restart the shutter dimmer motor Press MODE ENTER to confirm 5 Press EXIT DN to return to the main menu OTHR When you activate this reset function the fixture will only reset the other motors 1 Access the main menu 2 Tap the UP button until RESE is displayed press MODE ENTER 3 Tap the UP button until OTHR is displayed press MODE ENTER to confirm 4 The display will show ON OFF Press the UP button to select ON to reset the color motor Press MODE ENTER 5 Press EXIT DN to return to the main menu TIME MAIN MENU LIFE With this function you can display the total running time of the unit 1 Access the main menu 2 Tap the UP button until TIME is displayed press MODE ENTER 3 Tap the UP button until LIFE is displayed press MODE ENTER 4 Press EXIT to return to th
9. Orange 98 111 Purple 112 128 Pink 128 187 Forwards rainbow effect from fast to slow 188 193 No rotation 194 255 Backwards rainbow effect from slow to fast Channel 6 Rotating gobos cont rotation 0 9 Open 10 19 Rot gobo 1 20 29 Rot gobo 2 30 39 Rot gobo 3 40 49 Rot gobo 4 50 59 Rot gobo 5 60 69 Rot gobo 6 70 89 Gobo 1 shake slow to fast 90 109 Gobo 2 shake slow to fast 110 129 Gobo 3 shake slow to fast 130 149 Gobo 4 shake slow to fast 150 169 Gobo 5 shake slow to fast 170 189 Gobo 6 shake slow to fast 190 255 Rot gobo wheel cont rotation slow to fast Channel 7 _ Rotating gobo index rotating gobo rotation 0 127 Gobo indexing 128 187 Forwards gobo rotation from fast to slow 188 193 No rotation 194 255 Backwards gobo rotation from slow to fast Channel 8 Fixed Gobos 0 13 Open hole 14 27 Gobo 1 28 41 Gobo 2 42 55 Gobo 3 56 69 Gobo 4 70 83 Gobo 5 84 97 Gobo 6 98 111 Gobo 7 112 127 Gobo 1 shake slow to fast 128 143 Gobo 2 shake slow to fast 144 159 Gobo 3 shake slow to fast 160 175 Gobo 4 shake slow to fast 176 191 Gobo 5 shake slow to fast 192 207 Gobo 6 shake slow to fast 208 223 Gobo 7 shake slow to fast 224 255 Gobo wheel rotation from slow to fast Channel 9 _3 facet rotating prism Prism Gobo macros 0 3 open 4 63 Forwards rotation from fast to slow 64 67 No rotation 68 127 Backwards rotation from slow to fast 128 135 Macro 1 136 143 Macro 2 144 151 Macro 3 152 159 Macro 4 16
10. PROFESSIONAL SCANNER USER S MANUAL VER1 0 KEEP THIS MANUAL FOR FUTURE NEEDS C For your own safety please read this user manual carefully before installing the device CAUTION K eep this device away from rain and moisture CAUTION Unplug mains lead before opening the housing Every person involved with the installation operation and maintenance of this device has to be qualified follow carefully the instructions of this manual INTRODUCTION Thank you for having chosen this professional moving head You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find the fixture device a power cable an XLR connection cable a safety cable and this manual Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device Features Pan movement pan 155 Tilt movement tilt 45 3 operation mode DMX controlled stand alone or sound activated via built in microphone _ 8 colors plus white with two direction rainbow effect Switchable colour change mode 1 only full colours mode 2 colour change at every position _ rotating gobo wheel has 6 rotating gobos plus open all gobos can be easily replaceable and gobo indexing static gobo wheel has 7 static gobos plus open with different speed gobo shaking and gobo indexing strobe effect 0 15 flashes per second or random stro
11. am SCXX C 01 0 1 XX 00 FFH C 30 3 0 XX 00 FFH TIME T XX 01 FFH CEDT ON OFF RUN ON OFF Program test Main functions ADDRESS MENU AOO 1 A511 Value This is where you set the DMX address of the unit TEST MENU T 01 T XX Test Tests the functions of each channel There are eight channels but only channels 1 2 3 4 and 6 can be tested AUDI MENU MAST Master Runs the unit as master in sound active mode ALON Alone Runs the unit stand alone sound active mode RESE RESET MENU ALL Resets all the motors in the unit SCAN Reset the motors for pan tilt mirror movement COLR Color Resets the color motors GOBO Resets the gobo motors SHTR Resets the shutter motors OTHR Reset other motors TIME MENU LIFE Displays the fixtures total running time LAMP Displays the lamp running time CLMP Clears the lamp running time REVERSE PAN RPAN Reverse Pan Reverses the pan REVERSE TILT RTILT Reverse Tilt Reverses the tilt FINE MENU Switch between 16 bit and 8 bit DISPLAY MENU VALU DMX 512 Value Display the DMX 512 value of each channel D ON Display On Turns digital display on or off FLIP Flips the digital display 180 degree SPEC MENU LAAU Automatic lamp start with power DLOF Switch lamp via DMX controller DLAY Lamp delay on time SPOT This provides a spot beam for better lamp optimization R
12. be prism and prism rotating with 16 prism macros step zoom function 15 18 21 lens can be selected dimmer intensity from 0 100 Iris from 100 to 5 with pulse iris effect Frost effect lt 8 preset programs selectable Control board with 4 digit display and foil keyboard for adjusting the DMX starting address Pan tilt Reverse Program Reset lamp on off operating hours and etc digital display can be turn 180 reverse to fit for different installation position local or remote resetting auto test for all functions value of each DMX channel can be displayed save program edit and save the program to the incorporated EEPROM through the front control panel or external controller can save maximum 48 scenes and run the saved program by the run menu from the front control panel SAFETY INSTRUCTIONS CAUTION Becareful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual ES Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due
13. e main menu LAMP With this function you can display the running time of the lamp 1 Access the main menu 2 Tap the UP button until TIME is displayed press MODE ENTER 3 Tap the UP button until LAMP is displayed press MODE ENTER 4 Press EXIT to return to the main menu CLMP With this function you can clear the running time of the lamp Note Very Important Please clear the lamp time every time you replace the lamp Access the main menu Tap the UP button until TIME is displayed press MODE ENTER Tap the UP button until CLMP is displayed press MODE ENTER Press MODE ENTER the display will show ON OFF Press the UP button to select ON to activate this function or OFF to deactivate this function Press MODE ENTER to confirm Press EXIT DN to return to the main menu RPAN MAIN MENU RPAN The movement of the Pan will be reversed wm wb 1 Access the main menu 2 Tap the UP button until RPAN is displayed press MODE ENTER 4 The display will show ON OFF 5 Press the UP button to select ON to activate this function or OFF to deactivate this function 6 Press MODE ENTER to confirm 7 Press EXIT to return to the main menu RTLT MAIN MENU RTLT The movement of the Tilt will be reversed 1 Access the main menu 3 Tap the UP button until RTILT is displayed press MODE ENTER 4 The display will show ON OFF
14. get the maximum light output as shown below Please remember the lamp is not a hot restrike type you must wait for approximately 10 minutes after having turned off the lamp before you can turn it back on again CAUTION Do not operate this device with open cover b Mounting the device CAUTION Please consider the EN 60598 2 17 and the other respective national norms during the installation The installation must only be carried out by a qualified person The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year CAUTION Before taking into operation for the first time the installation has to be approved by an expert Cautions The effect should be installed outside areas where persons may reach it walk by or be seated CAUTION When installing the device make sure there is no highly inflammable material within a distance of min 0 5m Overhead mounting requires extensive experie
15. isy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 P Controller projector 3 projector 2 projector 1 starting address 33 starting address 17 starting address 1 Projector DMX starting address selection All fixtures should be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting address is achieved by setting the correct number on the display located on the base of the device You can set the same starting address for all fixtures or a group of fixtures or make different address for each fixture individually If you set the same address all the units will start to listen to the same control signal from the same channel number In other words changing the settings of one channel will affect all the fixtures simultaneously If you set a different address each unit will start to listen to the channel number you have set based
16. ixture will begin the reset motion 1 Access the main menu 2 Tap the UP button until RESE is displayed press MODE ENTER 3 Tap the UP button until ALL is displayed press MODE ENTER 4 The display will show ON OFF Press the UP button to select ON to reset the color motor 5 Press MODE ENTER to confirm 6 Press EXIT DN to return to the main menu SCAN When you activate this reset function the fixture will only reset the pan tilt motor 1 Access the main menu 2 Tap the UP button until RESE is displayed press MODE ENTER 3 Tap the UP button until SCAN is displayed press MODE ENTER to confirm 4 The display will show ON OFF Press the UP button to select ON to reset the pan tilt motor Press MODE ENTER to confirm 5 Press EXIT DN to return to the main menu COLR When you activate this reset function the fixture will only reset the color wheel motor 1 Access the main menu 2 Tap the UP button until RESE is displayed press MODE ENTER 3 Tap the UP button until COLR is displayed press MODE ENTER to confirm 4 The display will show ON OFF Press the UP button to select ON to reset the color motor Press MODE ENTER 5 Press EXIT DN to return to the main menu GOBO When you activate this reset function the fixture will only reset the gobo wheel motor 1 Access the main menu 2 Tap the UP button until RESE is displayed press MODE E
17. ll be editing channel 1 of your selected scene press MODE ENTER You can change the channel number by pressing the UP button 5 The display will show the DMX value for the channel that is being edited It will be displayed as 11XX it stands for Channel 11 of the editing scene the DMX value is XX 6 Adjust the DMX value by pressing the UP button until you get the expected effect for this channel 7 Press MODE ENTER to enter the editing of the other channels of the scene 8 Repeat steps 5 8 until you finish setting all the DMX values for all the channels of this scene each scene can have 15 channels maximum 9 Once all the channels are completed the display will ash TIME this stands for the time needed to run this scene 10 Press MODE ENTER to edit the time needed the display shows T XX XX stands for the time needed to run this scene For example T 02 means scene 1 needs 6 seconds to run T 15 means this scene needs 45 seconds to run Note XX is always three seconds not one second 11 Adjust the time needed by pressing the UP button 12 Press MODE ENTER to save the settings for the scene you are editing the display will change to the next scene automatically 13 Repeat steps 3 12 to edit other scenes you can edit and save 48 scenes maximum 14 Press EXIT to exit now you have edited and saved scenes using the control board The number of steps can be defined under EDIT a
18. mmer motor reset 97 99 Other motor reset 100 119 Internal program 1 120 139 Internal program 2 140 159 Internal program 3 160 179 Internal program 4 180 199 Internal program 5 200 219 Internal program 6 220 239 Internal program 7 240 255 Auto program by music CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 1 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 2 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed gt Qd CAUTION Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the lamp Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer TECHNICAL SPECIFICATIONS Power supply 98VAC 50Hz 0120VAC 50Hz 0208VAC 50
19. nce including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug Installation method via clamp Please refer to the picture below Screw one clamp each via a M10 screw and nut directly into the bracket of the scanner Pull the safety chain through the bracket of the base and over the trussing system or a safe fixation spot DMX 512 control connection Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX output DMX input XLR mounting sockat XLR mounting sockat 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically no
20. nd the scenes can be called up under Run To run the scenes see page 26 Editing procedure 2 Using an external controller 1 Access the main menu 2 Tap the UP button until EDIT is displayed Press MODE ENTER 3 The display will show SC01 this stands for the first scene number to be edited For example If SC01 is displayed you will be editing scene 1 4 Change the scene number by pressing the UP button 5 Press MODE ENTER the display will show C 01 the 1 stands for the channel number 1 6 Press the UP button until CEDT is displayed press MODE ENTER 7 The display will show OFF press the UP button so that ON is displayed press MODE ENTER 8 The display shows SC02 You have successfully downloaded the rst scene 9 Adjust the Step time needed by pressing the UP button 10 Call up the second scene in your controller now 11 Repeat steps 3 6 until all desired scenes are downloaded 12 Press EXIT to exit The number of steps can be defined under Step and the scenes can be called up under Run INSTRUCTIONS ON USE The moving head is controlled by 16 DMX channels DMX channel s functions and their values Channel1 PAN movement 8bit Channel 2 Pan fine Channel 3 TILT movement 8bit Channel 4 Tilt fine Channel 5 Color Wheel 0 13 Open white 14 27 Red 28 41 Blue 42 55 Green 56 69 Light Yellow 70 83 Mangenta 84 97
21. on the quantity of control channels of the unit That means changing the settings of one channel will affect only the selected fixture In the case of the scanner which is a 16 channel fixture you should set the starting address of the first unit to 1 the second unit to 17 16 1 the third unit to 33 17 16 and so on Note After switching on the machine will automatically detect whether DMX 512 data is received or not If the data is received the display will show A 001 with the actually set address If there is no data received at the DMX input the display flashes A001 with the actually set address This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the machine the controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector Control Board The Control Board offers several features you can simply set the starting address switch on and off the lamp run the pre programmed program or make a reset The main menu is accessed by pressing the Enter button for 3 seconds until the display starts flashing Browse through the menu by pressing the Up button Press the Enter button in order to select the desired menu You can change the selection by pressing the Up button Confirm every selection by pressing the Enter button You can leave every mode by pressing the Exit button The functions pro
22. one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc INSTALLATION INSTRUCTIONS a Installing or replacing the lamp CAUTION Only install the lamp with the device unplugged from the mains CAUTION The lamp has to be replaced when it is damaged or deformed Before replacing the lamp let the lamp cool down because during operation the lamp can reach very high temperature During the installation of halogen lamps do not touch the glass bulbs bare handed Always use a cloth to handle the lamps during insertion and removal Do not install lamps with a higher wattage They generate higher temperatures than which the device was designed for For the installation you need one Philips MSR 575 2 Procedure 1 Unscrew the 3 screws A B C on the bottom of the housing holding the plate where the lamp is underneath 2 Gently pull the socket holder using the knob in the middle 3 Carefully insert the lamp into the socket Please remember there is only one way to insert the lamp Gently slide the lamp and its lamp holder back into place and fasten the 2 screws 4 On the access plate there are 3 small screws marked 1 2 and 3 which are used to adjust the lamp holder in the lamp housing You can adjust the 3 screws to fine turn the position of the lamp to
23. play will show A001 Adjust the DMX address by pressing the UP or DOWN buttons 5 Press MODE ENTER to confirm 6 Press the EXIT button to return to the main menu When the display is on A001 you can directly press the UP or DN buttons to change the DMX start address TEST MAIN MENU TEST This will test the functions of each channel 1 Access the main menu 2 Tap the UP button until TEST is displayed press ENTER 3 The display will show T 01 You can now press the up button and test the different channels For example If you press the up button until T 03 is displayed the unit will test the color channel changing the color one by one and show the rainbow effect with different speeds There are eight channels but only channels 1 2 3 4 and 6 can be tested 5 Press MODE ENTER or EXIT to exit AUDI MAIN MENU MSTR Define the unit as the master in master slave mode 1 Access the main menu 2 Tap the UP button until AUDI is displayed press MODE ENTER 3 Tap the UP button until MSTR is displayed press MODE ENTER 4 Press EXIT to return to the main menu ALON Define the unit as a stand alone unit 1 Access the main menu 2 Tap the UP button until NODE is displayed press ENTER 3 Tap the UP button until ALON is displayed press MODE ENTER to confirm 4 Press EXIT to return to the main menu RESE MAIN MENU ALL When you activate the reset function the f
24. rn to the main menu FLIP This function will reverse the display 1800 1 Access the main menu 2 Tap the UP button until DISP is displayed 3 Press MODE ENTER the display will show ON OFF 4 Press the UP button to select ON to activate this function or OFF to deactivate this function 5 Press MODE ENTER to confirm 6 Press EXIT to return to the main menu SPEC MAIN MENU spot With this function you can adjust the lamp via the control board The shutter opens and the lamp can be adjusted In this mode the device will not react to any control signal Access the main menu 2 Tap the UP button until ADJU is displayed press ENTER 3 Tap the UP button until LADJ is displayed press ENTER 4 The display will show ON OFF 5 6 7 Press the UP button to select ON to activate this function or OFF to deactivate this function Press ENTER to confirm Press EXIT DN to return to the main menu DFSE With this function you can restore the factory settings of the device All settings will be set back to the default values Any edited scenes will be lost When restoring the factory settings the unit must be set to the address that the unit was in when you started editing Access the main menu Tap the UP button until SPEC is displayed press MODE ENTER Tap the UP button until DFSE is displayed press MODE ENTER The display will show ON
25. vided are described in the following sections Default settings shaded 0 ADDR A001 AS511 Indicate the staring DMX address A001 also is the setting for slave 1 TEST T 01 T XX Automatically test the function 2 AUDI MSTR Runs fixture as master for audio ALON Runs fixture as alone for audio 3 LAMP ON OFF Manually switches lamp on and off 4 RESE ALL ON OFF Reset all motors and returns fixture to home SCAN ON OFF Reset only motors for pan tilt COLR ON OFF Reset only motors for colors GOBO ON OFF Reset only motors for gobo and rotation SHTR ON OFF Reset only motors for shutter and or dimmer OTHR ON OFF Reset other motors 5 TIME LIFE 0000 9999 Displays the total fixture running time LAMP 0000 9999 Displays a lamps running time CLMP ON OFF Clear lamp running time 6 RPAN ON OFF Reverses the pan movements 7 RTLT ON OFF Reverses the tilt movements 8 FINE ON OFF Switch between 16 bit 8 bit 9 DISP VALU D XX_D 00 DXXX Display the DMX512 value of each channel DON ON OFF Display turn off after 2mins FLIP ON OFF This function will reverse the display 180 10 SPEC LAAU ON OFF Automatic lamp start with power DLOF ON OFF Switch lamp via DMX DLAY D XX D 15 Lamp on delay time SPOT ON OFF Lamp optimization DFSE ON OFF Resets all the fixture functions to default VER V1 0 V9 9 Software version 11 EDIT STEP S 01 S 48 Set the amount of your progr
26. which stated in the technical specifications in the last page of this manual the device was designed for indoor use only Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 0 5 meter Always fix the fixture with an appropriate safety cable if you use the clamp to hang up the fixture When fixing the device on a raised from the ground support be sure to use no less than screws and nuts of M10 x 25 mm and insert them in the pre arranged screw holes in the base of the fixture If you use the quick lock cam in hanging up the fixture please make sure the 4 quick lock fasteners turned in the quick lock holes correctly Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the
Download Pdf Manuals
Related Search