Powermoon Contractor Manual
Contents
1. If used or mixed with other systems or components POWERMOON warranty is no longer valid Attention when mounting the POWERMOON onto a tripod pole or moving machinery Ensure that the POWERMOON does not touch or interfere with overhead cables tree branches bridges etc For tripod use Ensure that the complete system has a secure stand to prevent it from toppling Inner tripod steles need to be horizontal 4 All screws must be tightened at all times Keep safety distance to roads pedestrians animals cars mobiles buildings etc We advise the usage of fixing lopes when lighting traffic routes for example POWERMOON fixing lopes One guy rope should then be in right angle to road to secure tripod from toppling on to road Alternatively weigh down POWERMOON tripod telescopic pole with additional material sandbags concrete blocks etc POWERMOON Lights and signals Make sure that the POWERMOON balloon or its light never mask other lights such as railway crossings signposts signals and traffic lights When lighting crowded areas such as sport events music festivals always secure the area around the balloon with barrier tape Also secure the guy ropes Environmental protection Emission of light in residential areas or protected nature reserves could be disturbing Read city guidelines for emission of light before use Inform all involved circles and facilities Disturbances to environment are po2. watt bulbs e g 400W or bigger watt bulb e g 1000W Information on bulb positioning The bulb position vertical is predetermined by the way the POWERMOON is constructed Bulbs that usually are used in horizontal position can be used as well Using these bulbs in an upright position will only reduce the lifespan of the bulb by approx 50 as the anodes and cathodes burn down unevenly 5 Close burst cage by clipping buttons 6 Close Velcro of bottom and top cove by starting at the corners Repair kit for small holes in balloon cover Small holes in the lower white cover can be pasted over with the self adhesive repair kit which is delivered together with the POWERMOONTM 6 Trouble Shooting 6 1 Mechanical Defects The POWERMOON won t open Should the POWERMOON not open properly grip handle won t slide easily over glider twist and turn grip handle while holding POWERMOON main bell firm Try to press down and open POWERMOON again 6 2 Electrical Defects The POWERMOON won t ignite and light up 1 Check power source 110V 50Hz should be available Check cables from balloon base to power source on possible damages or loose connections Are any cables or plugs broken Is there any interruption in current flow Are plugs correctly attached 3 Check if bulbs are placed in sockets correctly and that they show no damages Use hand gloves 12 Also check whether bulbs are placed in socket correctly It can happe
3. POWERMOONIM Contractor 2000W Halogen 4x500W Halogen USING INSTRUCTIONS US Patent No US 6 305 827 B1 US TM Reg No 2 537 683 Canadian Patent No 2311220 1 Congratulations on your purchase of aPOWERMOON balloon lighting system Your POWERMOON Contractor is the most up to date glare free floodlight system on the market and worldwide the only balloon light that works on basis of a solid and robust steel spring open and close mechanism This system ensures that your POWERMOON always stays open while in use Even when not running the POWERMOONT can stay open for days or even weeks Just as well as you can close it within seconds Your POWERMOONT is IP54 approved which means wind and weather resistant The benefits of a POWERMOON balloon lighting system No glare No harsh shadows Wide light distribution High portability Small storage Solid and robust gt safety and work efficiency at night increase enormously One more benefit Great looks and elegant design To ensure best possible lighting results and correct usage please read the manual carefully If you have any questions need further information or advice never hesitate to contact us POWERMOON Enterprises Ltd 113 Dials Drive Woodstock GA 30188 USA Phone 770 516 2266 Toll Free 1877 MOON 085 Fax 770 516 2267 info powermoon com www powermoon com Your POWERMOON team Table of contents Pa
4. ar protective goggles when changing cover of balloon Reason POWERMOON balloons open through stainless steel springs which might be uncontrollable If cover is severely damaged it must be changed 1 Change cover of balloon by opening Velcro 2 Open elastics 3 Apply new cover Velcro of lower cover must direct to outside 4 Close elastics 5 Close Velcro of bottom and top cove by starting at the corners For further info on how to change cover please visit website www powermoon com Bulb replacement Attention Precautions Completely unplug POWERMOON from any power source 10 Allow used bulbs to cool off before replacing Make sure not to touch any heated parts bulbs burst cage steel bars ceramic brackets etc on POWERMOON Wear gloves and protective goggles Bulbs are under high pressure and could explode implode Caution Do not look in to burning bulb Lamps radiate strong UV Light 1 Carefully open two 2 Velcro segments while balloon is fully opened 2 Open burst cage 4 Insert new bulb by placing it in the lower socket first Then gently press down bulb and place in upper socket Make sure it sits correct and firm 2 Insert bulb in upper socket after having it placed in lower socket 1 Insert bulb in lower socket first 11 Attention Improper insertion for example loose bulb may result in dangerous smoldering or other uncontrollable electricity flow Attention Never use smaller
5. ces Safety margins should be considered carefully when a POWERMOON is installed on vehicles and construction equipment High Voltage Cables should be at least approx 160 ft 50m linear distance Overhead railway electric lines should be kept at a distance of 8ft 2 5m Check regulation clearance of tripods for rail tracks Different regulations apply for different regions Check safety regulations and zones for airports ports and oil refineries Different regulations apply for different regions Ensure that the power supply cable of POWERMOON cannot be damaged or cut off by passing traffic and trains Pedestrians should not be endangered by wires which they could stumble over Take care when running POWERMOON with other machines on the same generator or power source Warning Check capacity of small generators of less than 15kVA before letting large machines use it at the same time as the POWERMOON Strong inductive and capacitance machines like POWERMOONs or engines immersion pumps have influence on phases and sine curves of generators Do not attach electronic equipment like computers televisions or hi fi s This equipment could be damaged when turning the POWERMOON on and off due to the surge in voltage This occurs especially if the electronic control unit is defective Violation of the above results in responsibility of user and frees manufacturer from all liabilities Violation of the above and any defect o
6. en changing tripod segments Attention Pay attention to wind and weather We advise to tie rope tripods or other masts as wind and weather conditions might change Attention Make sure that inner steles are horizontal and all three tripod stands are on ground This could for example not be the case if middle pole is touching ground as well lt gt Br VEG Br EA SE JESS ve SA DEE ET 4 Pa at p A A vs ST Re a O ee nn eee ee Petree z e oe My f 8 Plug POWERMOON cord in to power source Turn off POWERMOON 1 Turn of POWERMOON by pulling power plug out of power source 3 Close POWERMOON by holding black handle bar and pulling pin Slowly close POWERMOON by letting handle bar slide up POWERMOON middle axis Attention Wait until bulb has cooled off Approx 4 8min 3 Electrical requirements and data Voltage 100V 120V Hertz 50Hz 60Hz Amps 16 66A Bulbs 4x500W halogen Type T Base R s 4 Care and maintenance The POWERMOON may get damp with use Always let the POWERMOON dry out before storing it in bag or cylinder Small holes in translucent cover can be pasted with self adhesive repair kit Dirt on both top and bottom cover can be wiped off with thin soap liquid Do not clean cover with any solvent as it will be destroyed Leave defective cables or broken plugs for an electrician to repair 5 Parts replacement Balloon cover replacement Caution We advise to we
7. ge 4 Page 7 Page 10 Page 11 Page 11 Page 13 Safety Instructions POWERMOON Using Instructions Electrical Requirements Care And Maintenance Parts Replacement incl bulb replacement Trouble Shooting 1 Safety Instructions Caution before using the POWERMOON read all instructions POWERMOON is a fuseless system and can only be used with power sources that have a circuit breaker POWERMOON can be used both indoors and outdoors The system is IP54 approved weather and rain proof After unpacking Check all electrical cables for damages or cutts Make sure that the bulb is free of any packing material used for transport Check bulbs for cracked glass or any other transport caused damage Vibration during transportation could cause bulb to shatter Use gloves Check if bulbs are properly placed in ceramic sockets Use gloves If the POWERMOON has already been used check the following before reuse Cables should not be cut or damaged Power plug should be checked for burn damage cracks etc In case of any damage check with a professional electrician before continuing Safety instructions and restrictions for your own operational safety The POWERMOON and all additional equipment such telescopic poles etc can only be used for lighting purposes Any other use happens at users own risk and liability POWERMOON components should not be used mixed together with other lighting systems or components
8. n other machines equipment and instruments coming thereof caused for example by regeneration back coupling is not the manufacturers responsibility 2 POWERMOON using instructions Attention Never switch POWERMOON on before it has been completely assembled Always pay attention to warning labels and using instructions 1 Take POWERMOON cords out of bag or cylinder before taking out POWERMOON 2 When using cylinder Take POWERMOON out of cylinder by gripping pin and gently pulling the POWERMOON 3 Place POWERMOON with bottom pin on solid ground Grip black handle bar pull pin and press down until POWERMOON is fully opened and locked in place 4 Check if Velcro is closed all around and if transparent balloon cover is not damaged In case of bigger damages repair with delivered repair kit or change cover 5 Lift POWERMOON by gripping bottom pin with one hand and upper cover with other hand Mount POWERMOON on suitable tripod or other mast 6 If using a tripod bring it up to desired height Optimal installation height of balloon is 13 16ft 4 5 meters m Attention when mounting the POWERMOON onto a tripod pole or moving machinery Ensure that the POWERMOON does not touch or interfere with overhead cables tree branches bridges etc DANGER Attention Always watch hands when bringing tripod up and down Attention Always make sure to tighten all screws wh
9. n that during transport a bulb loosens Even though the bulb might ignite when not placed in socket correctly sparks might cause smouldering and bulbs might melt Change bulb and socket if this should have happened All necessary spare parts are available from POWERMOON Enterprises Ltd 13
10. ssible when not using sound proof generators as electric power supply Make sure to use up to date power supplies Clearance distance Radiation heat protection Always keep a clearance distance of min 3 feet to easy burnable materials such as wood plastics and textile such as curtains wooden ceiling wooden walls plastic foam insulation etc Z ats Attention when mounting the POWERMOON onto a tripod pole or moving machinery Ensure that the POWERMOON does not touch or interfere with overhead cables tree branches bridges etc DANGER Keep lamp away from materials that may burn Do not use a POWERMOON near open or leaking highly inflammable mediums gasoline and gas Do not use POWERMOON in EX Zones Do not use POWERMOON for salvage or rescue work with tank ship disasters damages in refineries or gas pipelines Lighting inside tanks big chimneys and floating bodies POWERMOONS should only be used with a suitable insulating transformer when inside enclosed areas and chimneys as well as floating metal pontoons ships and wrecks In such cases an electrician should test safety before starting Check regional rules of conduct with a professional electrician when using the POWERMOONT or other electric devices on ships If a person and a POWERMOON are situated on the same metal base insulation and earth grounding precautions must be taken Keep POWERMOON away from pylons and high voltage sour
Download Pdf Manuals
Related Search