Start Up
Contents
1. OPEN LED will turn on green 2 User the Iris Adjustment Dial for intensity adjustment to desired level Warning UV light and high levels of visible light will be emitted from the end of the light guide 3 Press the SHUTTER button to close the shutter The OPEN indicator will turn off Adjusting Light Output 1 To adjust light intensity use the Iris Adjustment Dial and set to desired level by turning 2 There are no hard stops motion is smooth from 0 to 100 0 12 5 25 50 100 are marked on the fascia around the dial for reference 3 Note that as the lamp ages absolute power at a given setting will decrease Adjust the intensity as necessary If monitoring absolute value of lamp output is desired contact Lumen Dynamics about purchasing the X Cite Optical Power Measurement System Viewing Accumulated Lamp Hours 1 The X Cite 200DC system automatically accumulates the number of hours for which the lamp has been on and shows this information on the LED display The lamp hours are shown when the unit is powered on and after lamp has warmed up Refer to User Guide 035 00446R for Power Measurement options button WARNING Never look into the light emitting end of the light guide The light could severely damage the cornea and retina of the eye l l f d if the light is observed directly Eye shielding must be used at all times as well as clothing to protect exposed skin Printed in Canada Refer to X Cite 200DC User s2. Guide 03500446R Section 3 035 00447R Rev O e X Cite Fluorescence Illumination In Control SIDE 2 X Cite 200DC Quick Start Guide AN Warning Refer to User Manual 035 00446R for all safety precautions prior to use Installing the Lamp Module 6 Locate the 4 pin Intelli Lamp sensor connector at the rear of the lamp module 1 Be sure the AC power cord is disconnected from the unit and connect it to its mate located on the top of the lamp housing wall 2 Remove the screw from the lamp access side panel using the 3mm hex Tip the Intelli Lamp connector will only attach in the correct orientation If tool you are having difficulty attaching the connector try rotating it by 180 3 Carefully remove the lamp module from its container holding only the ceramic component and glass rim 4 As illustrated below position the lamp facing towards the front of the unit with the power leads facing towards you Caution Do not touch the bulb s glass envelope or the inside surface of the reflector Skin oils can cause the lamp module to fail prematurely Rim 7 Locate the Power connector with two leads and connect it to its mate located on the bottom of the lamp housing wall Tip the Lamp Power connector will only attach in the correct orientation If you are having difficulty inserting the connector try rotating it by 180 5 Make sure the middle of the lamp is in position to fit into the spring clamp Slide the lam
3. X Cite Fluorescence Illumination In Control SIDE 1 X Cite 200DC Quick Start Guide Warning Refer to User Manual 035 00446R for all safety precautions prior to use Start Up Install the lamp module see side 2 Install the light guide see below Plug the unit into a properly grounded AC outlet Turn on the Power switch at the front of the unit The lamp will automatically strike when power is turned on to the unit The LAMP indicator will be illuminated Allow the lamp to warm up approximately 4 minutes During the warm up period the LED display and indicators will flash Se oN Installing the Light Guide 1 Remove the protective end caps from the light guide 2 Insert the light guide into the light guide port on the front panel until it seats with a positive click 3 Insert the light emitting end of the light guide into the collimating adapter after it has been installed on the microscope Front Panel Controls 1 SHUTTER button will open close the shutter OPEN LED will indicate when shutter is open 2 Power on off switch 3 Iris Adjustment Dial Using the Footpedal Remote Device 1 Connect Footpedal remote device to 3 5mm jack at rear of unit 2 Depressing the footpedal or providing a momentary contact closure provides the same function as pressing the SHUTTER Illuminating a Specimen 1 To Illuminate a specimen press and release the SHUTTER button to open the shutter
4. p until it snaps into the spring clamp The leading Center edge of the reflector should fit snugly into the lamp holder recess lamp power lead as shown 8 It is very important to ensure that the lamp anode cooling fin bar and lamp power lead at the front of the lamp are centered within the lamp holder cutout Rotate the lamp as required 9 Replace the lamp housing side panel and tighten the fastening screw 10 Replace the hex tool in the clips underneath the system for future use Note if the lamp housing panel is not secured completely the lamp will not strike and the bulb message will display when power is turned on to the unit Lumen Dynamics Group Inc Tel 1 905 821 2600 2260 Argentia Rd Toll Free 1 800 668 8752 Mississauga Ont Fax 1 905 821 2055 Canada LSN 6H7 www ldgi xcite com
Download Pdf Manuals
Related Search